INSTRUCTION MANUAL

VHF MARINE TRANSCEIVER

iM33
 DECLARATION
OF CONFORMITY

We Icom Inc. Japan

1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan 0560
Declare on our sole responsability that this equipment complies the
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test Düsseldorf 30th Nov. 2006
Suite measurements have been performed. Place and date of issue

Kind of equipment: VHF MARINE TRANSCEIVER

Icom (Europe) GmbH
Himmelgeister straße 100
Type-designation: iM33 D-40225 Düsseldorf
Authorized representative name
Version (where applicable):
H. Ikegami
This compliance is based on conformity with the following harmonised General Manager
standards, specifications or documents:
i) EN 301 178-2 V1.1.1 (2000-8)
ii) EN 60945 2002
iii) EN 60950-1 2001
iv) EN 300 698-2 V1.1.1 (2000-8)
v) EN 300 698-3 V1.1.1 (2001-5)
vi) Signature
vii)

CE Versions of the IC-M33 which display the This warning symbol indicates that this equipment
“CE” symbol on the serial number seal, comply operates in non-harmonised frequency bands
with the essential requirements of the Euro- and/or may be subject to licensing conditions in
pean Radio and Telecommunication Terminal the country of use. Be sure to check that you have
Directive 1999/5/EC. the correct version of this radio or the correct pro-
gramming of this radio, to comply with national li-
censing requirement.
i
IN CASE OF EMERGENCY RECOMMENDATION
If your vessel requires assistance, contact other vessels and CLEAN THE TRANSCEIVER THOROUGHLY WITH FRESH
the Coast Guard by sending a distress call on Channel 16. WATER after exposure to saltwater, and dry it before opera-
tion. Otherwise, the transceiver's keys, switches and con-
trollers may become unusable due to salt crystallization.
❍ USING CHANNEL 16
NOTE: DO NOT wash the transceiver in water if there is any
DISTRESS CALL PROCEDURE reason to suspect the waterproofing may not be effective. For
example, in cases where the battery pack rubber seal is dam-
aged, the transceiver/battery pack is cracked or broken, or
1. “MAYDAY MAYDAY MAYDAY.” has been dropped, or when the battery pack is detached from
the transceiver.
2. “THIS IS ...........................” (name of vessel)
3. Your call sign or other indication of the ves-
sel.
4. “LOCATED AT .....................” (your position)
5. The nature of the distress and assistance re-
quired.
6. Any other information which might facilitate
the rescue.

ii
 FOREWORD FEATURES
Thank you for purchasing this Icom radio. The IC-M33 VHF MA- ☞ Submersible construction
RINE TRANSCEIVER is designed and built with Icom’s state of the Built tough to withstand the punishing marine environ-
art technology and craftsmanship. With proper care this radio ment, the IC-M33’s submersible construction meets IPX7
should provide you with years of trouble-free operation. of the corresponding International Standard IEC 60529
(2001) while using BP-251 (option) or BP-252.

☞ Floating on water
IMPORTANT The IC-M33 floats on fresh or salt
water even when the supplied acces-
READ ALL INSTRUCTIONS carefully and com-
sories are attached.
pletely before using the transceiver. • When third-party battery pack, strap, an-
tenna, etc. is used, it may sink.
SAVE THIS INSTRUCTION MANUAL—This in- • The battery contacts may be prone to rust-
struction manual contains important operating instructions for ing if the transceiver is kept floating in
the IC-M33. fresh or salt water.

☞ Large, easy-to-read LCD

With dimensions of 16(H) × 32(W) mm, the IC-M33’s func-
EXPLICIT DEFINITIONS tion display is easy to read and shows operating condi-
tions at a glance. Backlighting and contrast can be
WORD DEFINITION adjusted to suit your preferences.
Personal injury, fire hazard or electric shock
RWARNING may occur. ☞ Simple operation
9 large buttons on the front panel provide user-friendly op-
CAUTION Equipment damage may occur.
eration. The independent volume and channel buttons are
If disregarded, inconvenience only. No risk located on the front panel for convenient one-hand opera-
NOTE
of personal injury, fire or electric shock.
tion.
iii
PRECAUTIONS
RWARNING! NEVER connect the transceiver to an BE CAREFUL! The transceiver employs waterproof
AC outlet. This may pose a fire hazard or result in an electric construction, which corresponds to IPX7 of the international
shock. standard IEC 60529 (2001). However, once the transceiver
has been dropped, waterproofing cannot be guaranteed due
RWARNING! NEVER hold the transceiver so that the
to the fact that the transceiver may be cracked, or the water-
antenna is closer than 2.5 cm from exposed parts of the body,
proof seal damaged, etc.
especially the face or eyes, while transmitting. The trans-
ceiver will perform best if the microphone is 5 to 10 cm away MAKE SURE the flexible antenna and battery pack are
from the lips and the transceiver is vertical. securely attached to the transceiver, and that the antenna and
battery pack are dry before attachment. Exposing the inside
NEVER connect the transceiver to a power source other
of the transceiver to water will result in serious damage to the
than the BP-251 (option) or BP-252. Such a connection will
transceiver.
ruin the transceiver.
After exposure to water, clean the battery contacts thoroughly
AVOID using or placing the transceiver in direct sunlight or with fresh water and dry them completely to remove any
in areas with temperatures below –15°C or above +55°C. water or salt residue.
KEEP the transceiver out of the reach of children.
KEEP the transceiver at least 0.9 meters away from your
vessel’s magnetic navigation compass.
BE CAREFUL! The transceiver’s right-side panel will
become hot when operating continuously for long periods.

Icom, Icom Inc. and the logo are registered trademarks of Icom Incor-
porated (Japan) in the United States, the United Kingdom, Germany, France,
Spain, Russia and/or other countries.
iv
 TABLE OF CONTENTS
DOC ........................................................................................... i 5 SCAN OPERATION (Except Holland version) ........ 14–15
IN CASE OF EMERGENCY ..................................................... ii ■ Scan types .................................................................... 14
RECOMMENDATION ............................................................... ii ■ Setting TAG channels ................................................... 15
FOREWORD ............................................................................ iii ■ Starting a scan .............................................................. 15
IMPORTANT ............................................................................ iii 6 DUALWATCH/TRI-WATCH (Except Holland version) ... 16
EXPLICIT DEFINITIONS .......................................................... iii ■ Description .................................................................... 16
FEATURES .............................................................................. iii ■ Operation ...................................................................... 16
PRECAUTIONS ....................................................................... iv 7 SET MODE ................................................................. 17–20
TABLE OF CONTENTS ............................................................ v ■ Set mode programming ................................................ 17
1 OPERATING RULES ......................................................... 1 ■ Set mode items ............................................................. 18
2 SUPPLIED ACCESSORIES AND ATTACHMENTS ....... 2–3 8 BATTERY CHARGING ............................................... 21–24
■ Supplied accessories ....................................................... 2 ■ Battery caution .............................................................. 21
■ Attachments ..................................................................... 2 ■ Supplied battery charger ............................................... 23
3 PANEL DESCRIPTION .................................................. 4–7 ■ Optional battery case ..................................................... 23
■ Front, top and side panels ............................................... 4 ■ Optional battery charger ............................................... 24
■ Function display .............................................................. 6 9 OPTIONAL SPEAKER-MICROPHONE ........................... 25
4 BASIC OPERATION .................................................... 8–13 ■ HM-165 descriptions ..................................................... 25
■ Channel selection ........................................................... 8 ■ Attachment .................................................................... 25
■ Receiving and transmitting ............................................ 10 10 TROUBLESHOOTING ..................................................... 26
■ Call channel programming ............................................ 11 11 VHF MARINE CHANNEL LIST ........................................ 27
■ Adjusting the volume level ............................................. 11 12 SPECIFICATIONS............................................................. 28
■ Volume mute function .................................................... 11
13 OPTIONS .......................................................................... 29
■ Adjusting the squelch level ........................................... 12
■ Lock function ................................................................. 12
■ Automatic backlighting .................................................. 12
■ Monitor function ............................................................ 13
■ AquaQuake water draining function .............................. 13
v
 OPERATING RULES 1
D Priorities (2) OPERATOR’S LICENSE
1
• Read all rules and regulations pertaining to priorities and A restricted Radiotelephone Operator Permit is the license
keep an up-to-date copy handy. Safety and distress calls most often held by small vessel radio operators when a radio
take priority over all others. is not required for safety purposes.

• You must monitor Channel 16 when you are not operating The Restricted Radiotelephone Operator Permit must be
on another channel. posted near the transceiver or be kept with the operator. Only
a licensed radio operator may operate a transceiver.
• False or fraudulent distress calls are prohibited under law.
However, non-licensed individuals may talk over a transceiver
if a licensed operator starts, supervises, ends the call and
D Privacy makes the necessary log entries.
• Information overheard but not intended for you cannot law-
fully be used in any way. A current copy of the applicable government rules and regu-
lations is only required to be on hand for vessels in which a
• Indecent or profane language is prohibited. radio telephone is compulsory. However, even if you are not
required to have these on hand it is your responsibility to be
thoroughly acquainted with all pertinent rules and regulations.
D Radio licenses
(1) SHIP STATION LICENSE
When your craft is equipped with a VHF FM transceiver, you
must have a current radio station license before using the
transceiver. It is unlawful to operate a ship station which is not
licensed.

Inquire through your dealer or the appropriate government

agency for a Ship-Radiotelephone license. This license in-
cludes the call sign which is your craft’s identification for radio
purposes.

1
 2 SUPPLIED ACCESSORIES AND ATTACHMENTS

■ Supplied accessories
D Handstrap
Handstrap Battery pack Battery charger AC adapter
(with 2 screws) (Not supplied with Pass the handstrap through
some version) the loop on the side of the
transceiver as illustrated at
right. This facilitates carry-
ing.

Antenna Belt clip

D Belt clip
Attach/detach the belt clip to the transceiver as illustrated
below.
To attach the belt clip To detach the belt clip
■ Attachments
D Flexible antenna w Be careful!
Not to break
Connect the supplied flexible an-
your nails.
tenna to the antenna connector.

CAUTION!
• NEVER carry the transceiver
by the antenna. q
• Transmitting without an an-
tenna may damage the trans-
ceiver.
2
 SUPPLIED ACCESSORIES AND ATTACHMENTS 2

ï Battery pack
To remove the battery pack: NOTE: When removing or attaching the battery pack, use
Turn the screw counterclockwise one quarter turn, then pull a coin or standard screwdriver to loosen or tighten the bot- 2
the battery pack in the direction of the arrow as shown below. tom screw.

To attach the battery pack: CAUTION!:

Insert the battery pack in the IC-M33 completely, then turn the When attaching or removing a battery pack, make sure the
screw clockwise one quarter turn. rubber seal is set in the groove of the battery pack cor-
rectly. If the seal is not neatly in the groove it may be dam-
NEVER remove or insert the battery pack when the trans- aged when attaching the battery pack.
ceiver is wet or soiled. This may result water or dust get- If the seal is damaged, waterproofing is not guaranteed.
ting into the transceiver/battery pack and may result in the
transceiver being damaged.
NOTE:
When attaching a battery pack, make sure dust or other
material does not adhere to the rubber seal. If dust or other
material is on the seal when attaching a battery pack, water
resistance may be compromised.

Screw position Make sure the rubber seal (purple) is properly seated in the
when removing battery groove and dust or other material does not adhere to it.

Screw position
when attaching battery Correct position Incorrect position

Rubber seal
Groove
Battery pack Battery pack

3
 3 PANEL DESCRIPTION

■ Front, top and side panels

q POWER SWITCH [PWR]
w
Push and hold to turn power ON and OFF.
q e
w SPEAKER-MICROPHONE CONNECTOR [SP MIC] (p. 25)
Connects the optional external speaker-microphone.
NOTE: Attach the [SP MIC] cap when the optional
speaker-microphone is not used. Otherwise, water will
!2 Speaker get into the transceiver.
Microphone q
Function display q Attach the [SP MIC] cap.
(pgs. 6, 7)

w Then rotate it clockwise

r completely.
!1 w
t
y
!0
u e ANTENNA CONNECTOR (p. 2)
o Connects the supplied antenna.
i
r CHANNEL KEY [CH]
➥ Selects the regular channel when pushed. (p. 9)
➥ Selects the U.S.A.,* International or ATIS† channel group
when pushed and held for 1 sec. (p. 9)
➥ Push to return to the previous channel before selecting
channel 16 or the call channel.
*U.K. version only; †German and Holland versions only

4
 PANEL DESCRIPTION 3

t FAVORITE/TAG KEY [FAV•TAG] o SCAN/DUAL KEY [SCAN•DUAL]

➥ While pushing and holding this key, push [Y]/[Z] to se- ➥ Push to start or stop normal or priority scan. (p. 15) 3
lect the favorite (TAG) channels with ignoring untagged ➥ Push and hold for 1 sec. to enter watch mode. (p. 16)
channels in the selected channel group in sequence. ➥ Push and hold this key and [H/L], to activate the
(p. 8) AquaQuake function. (p. 13)
• Pushing this key only advances the displayed TAG channel. ➥ Exits watch mode when pushed during watch operation.
➥ Push and hold for 1 sec. to set or clear the displayed (p. 16)
channel as a TAG (scanned) channel. (p. 15)
!0 VOLUME KEY [VOL•MUTE]
➥ While pushing and holding this key, turn power ON to
➥ Push this key, then adjust the volume level with [Y]/[Z].
clear or set all TAG channels (when no TAG channel has
(p. 11)
been set) in the selected channel group. (p. 15)
➥ Push and hold for 1 sec. to activate the volume mute
y SQUELCH/MONITOR KEY [SQL•MONI] function. (p. 11)
➥ Push this key, then adjust the squelch level with [Y]/[Z].
!1 CHANNEL 16 KEY [16•C]
(p. 12)
➥ Push to select Channel 16. (p. 8)
➥ Manually opens the squelch for monitoring the channel
➥ Push and hold for 1 sec. to select the call channel. (p. 8)
while pushing and holding. (p. 13)
➥ Enters call channel programming condition when the call
➥ While pushing and holding this key, turn power ON to
channel is selected and this key is pushed and held for 3
enter the set mode. (p. 17)
sec. (p. 11)
u TRANSMIT POWER/LOCK KEY [H/L•LOCK] ➥ Push to exit set mode during set mode operation. (p. 17)
➥ Selects high or low power when pushed. (p. 10)
!2 PTT SWITCH [PTT]
➥ Toggles between the key lock function ON/OFF when
Push and hold to transmit; release to receive. (p. 10)
pushed and held for 1 sec. (p. 12)
i CHANNEL UP/DOWN KEYS [Y Y]/[ZZ]
➥ Selects an operating channel. (pgs. 8, 9)
➥ Selects the set mode setting of the item. (p. 17)
➥ Checks TAG channels or changes scanning direction
during scan. (p. 15)
5
 3 PANEL DESCRIPTION

■ Function display
q w e r t y t LOCK INDICATOR (p. 12)
Appears while the lock function is activated.
y BATTERY INDICATOR
u Indicates remaining battery power.
!8
i Indication
o
!7 Charging
!0 Battery level Full Middle
required
No battery
!6
!1 blinks when the battery is over charged.
!2 blinks when the battery is exhausted.

!5 !4 !3 u SCAN INDICATOR (p. 15)

Blinks while scanning.
q TRANSMIT INDICATOR (p. 10)
i DUALWATCH/TRI-WATCH INDICATORS (p. 16)
Appears while transmitting.
“DUAL” appears during dualwatch; “TRI” appears during
w BUSY INDICATOR tri-watch.
➥ Appears when receiving a signal or when the squelch
o DUPLEX INDICATOR
opens. (p. 10)
Appears when a duplex channel is selected.
➥ Blinks while monitoring. (p. 13)
!0 SUB CHANNEL READOUT
e TAG CHANNEL INDICATOR (p. 15)
➥ Indicates Channel 16 during priority scan, dualwatch or
Appears when a TAG channel is selected.
tri-watch. (p. 16)
r CALL CHANNEL INDICATOR (p. 8) ➥ Indicates the set mode item while in set mode. (p. 17)
Appears when the call channel is selected. ➥ Indicates the squelch level while squelch setting. (p. 12)
➥ Indicates the volume level while volume setting. (p. 11)

6
 PANEL DESCRIPTION 3

!1 SQUELCH LEVEL INDICATOR

Shows the squelch level. 3
!2 VOLUME LEVEL INDICATOR
➥ Shows the volume level.
➥ Blinks when the volume mute is activated. (p. 11)
!3 VOLUME LEVEL ADJUSTING INDICATOR (p. 11)
Blinks while adjusting the volume level.
!4 SQUELCH LEVEL ADJUSTING INDICATOR (p. 12)
Blinks while adjusting the squelch level.
!5 CHANNEL NUMBER READOUT
➥ Indicates the selected operating channel number.
➥ In set mode, indicates the selected condition.
!6 CHANNEL GROUP INDICATOR (p. 9)
U” appears when U.S.A.*; “ ” appears when Interna-
“U
tional.
*U.K. version only
!7 ATIS INDICATORS (p. 9)
➥ “ATIS” appears when the channel group, which ATIS
function is activated, is selected. (Available with German
and Holland versions only)
!8 LOW POWER INDICATOR (p. 10)
➥ “LOW” appears when low power is selected.
➥ “LOW” blinks when switching forced low power mode
because of a high temperature error or low voltage.

7
 4 BASIC OPERATION

■ Channel selection
IMPORTANT!: Prior to using the transceiver for the first D Call channel
time, the battery pack must be fully charged for optimum Each regular channel group has separate leisure-use call
life and operation. To avoid damage to the transceiver, turn channels. The call channel is monitored during Tri-watch. The
the power OFF while charging. call channels can be programmed (p. 11) and are used to
store your most often used channel in each channel group for
D Channel 16 quick recall.
Channel 16 is the distress and safety channel. It used for es-
tablishing initial contact with a station and for emergency q Push and hold [C] (16) for 1 sec. to select the call channel
communications. Channel 16 is monitored during both Dual- of the selected channel group.
watch and Tri-watch. While standing by, you must monitor • “CALL” and call channel number appear.
Channel 16. • Each channel group may have an independent call channel after
programming a call channel. (p. 11)
q Push [16] momentarily to select Channel 16. w Push [CH] to return to the channel used before call chan-
w Push [CH] to return to the channel used before Channel Y]/[Z
nel, or push [Y Z] to select a channel.
Y]/[Z
16, or push [Y Z] to select a channel.
Push and hold
for 1 sec.
Push

Convenient!
While pushing and holding [FAV], push [Y]/[Z] to select the
favorite (TAG) channels with ignoring untagged channels in
the selected channel group in sequence.
• Pushing [FAV] only advances the displayed TAG channel.
• The favorite channels are selected using the TAG channel setting.
(p. 15)
8
 BASIC OPERATION 4

D U.S.A., International and ATIS channels

The IC-M33 is pre-programmed with U.S.A.*, International
and ATIS† channels. These channel groups may be specified
for the operating area. 4
*U.K. version only; German and Holland versions only
†

q Push [CH] to select a regular channel.

w Push and hold [CH] for 1 sec. to change the channel
group. Repeat to advance to the next group.
• U.S.A., International and ATIS channel groups can be selected in
sequence.
e Push [Y
Y]/[Z
Z] to select a channel.
• “DUP” appears for duplex channels.

International channels

Push and hold

for 1 sec.

U.S.A. channels ATIS channels

9
 4 BASIC OPERATION

■ Receiving and transmitting

CAUTION: Transmitting without an antenna will damage IMPORTANT: To maximize the readability of your trans-
the transceiver. mitted signal, pause a few sec. after pushing [PTT], hold
the microphone 5 to 10 cm from your mouth and speak
q Push and hold [PWR] to turn power ON. into the microphone at a normal voice level.
w Set the audio and squelch levels. NOTE: The transceiver has a power save function to con-
➥ Push [SQL], and push [Z
Z] several times to open the squelch. serve the battery power. The power save function activates
➥ Push [VOL], then push [Y
Y]/[Z
Z] to adjust the volume level.
automatically when no signal is received for 5 sec.
➥ Push [SQL], and push [Y
Y] until the noise disappears.
e Push [Y
Y]/[Z
Z] to select the desired channel.
• When receiving a signal, “ ” appears and audio is emitted
from the speaker.
• Further adjustment of the audio may be necessary at this point. t Push to q Power ON
r Push [H/L] to select the output power if necessary. transmit
• “LOW” appears when low power is selected; no indication when y Release to
high power is selected.
receive
• Choose low power to conserve battery power, choose high
power for longer distance communications. Microphone e Set channel
• Some channels are for low power only.
t Push and hold [PTT] to transmit, then speak into the w Set volume w Set the
microphone.
squelch level
•“ ” appears.
• Channel 70 cannot be used for transmission.
y Release [PTT] to receive. w Set the squelch r Set output
and volume level. power

10
 BASIC OPERATION 4

■ Call channel programming ■ Adjusting the volume level

Call channel is used to access Channel 16 (default; may differ Y]/[Z
The volume level can be adjusted with [VOL] and [Y Z].
according to version), however, you can program the call chan-
nel with your most often-used channels in each channel q Push [VOL], then adjust the volume level with [Y
Y]/[Z
Z].
group for quick recall. • “VOL” indicator starts blinking. 4
• There are 31 volume levels and OFF.
q Push and hold [CH] for 1 sec. several times to select the • When no key is pushed for 5 sec., the transceiver returns to nor-
desired channel group (U.S.A., International or ATIS) to be mal condition.
programmed. (p. 9) w Push [VOL] again to return to normal condition.
w Push and hold [C] (16) for 1 sec. to select the call channel
of the selected channel group.
• “CALL” and call channel number appear. Indicates the
e Push and hold [C] (16) again for 3 volume level.
sec. (until a long beep changes to
2 short beeps) to begin call chan- Blinks during volume level adjustment.
nel programming.
• Channel number starts blinking.
■ Volume mute function
r Push [Y
Y]/[Z
Z] to select the desired The volume mute function can be activated temporarily with
channel. [MUTE] (VOL).
t Push [16] to program the dis-
played channel as the call chan- q Push and hold [MUTE] (VOL) for 1 sec to activate the vol-
nel. ume mute function.
• The channel number stops blinking. • The audio is muted.
• The volume level indicator starts blinking.
w Push [VOL] again or turn power OFF to turn the volume
mute function OFF.

11
 4 BASIC OPERATION

■ Adjusting the squelch level ■ Lock function

To adjust the IC-M33’s squelch level, use the [Y Y]/[Z
Z] keys as This function electronically locks all keys (except for [PTT],
described below. In order to receive signals properly, as well [SQL•MONI], [VOL•MUTE], [H/L•LOCK] and [Y Y]/[ZZ]*) to
as for the scan to function effectively, the squelch must be ad- prevent accidental channel changes and function access.
justed to the proper level. * After pushing [VOL•MUTE] or [SQL•MONI] only.
➥ Push and hold [LOCK] (H/L) for 1 sec. to turn the lock
q Push [SQL], then adjust the squelch level with [Y
Y]/[Z
Z]. function ON and OFF.
• “SQL” indicator starts blinking. Appears while the lock
• There are 11 squelch levels to choose from: OP is completely function is used.
open; 10 is tight squelch; 1 is loose squelch.
• If no key is pushed for 5 sec., the transceiver returns to normal
operation.
Push and hold
w Push [SQL] again to return to normal condition.
for 1 sec.

Indicates the
squelch level.

Blinks during squelch

■ Automatic backlighting
level adjustment.
This function is convenient for nighttime operation. The auto-
matic backlighting can be activated in set mode. (p. 19)
➥ Push any key except for [PTT] to turn the backlighting ON.
• The backlighting is automatically turned OFF after 5 sec. of in-
activity.

12
 BASIC OPERATION 4

■ Monitor function
The monitor function opens the squelch. See p. 5 for details
of the monitor key action.

➥ The monitor function activates while pushing and holding 4

[MONI] (SQL).
•“ ” blinks and audio is emitted.
Blinks while the monitor function is used.

Push and hold

■ AquaQuake water draining function

The IC-M33 uses a new technology to clear water away from
the speaker grill: AquaQuake. AquaQuake helps drain water
away from the speaker housing (water that might otherwise
muffle the sound coming from the speaker). The IC-M33
emits a vibrating beep when this function is being used.

➥ Push and hold both [SCAN] and [H/L].

• A low beep tone sounds for 9 sec. to drain water, regardless of
volume level setting.
• The transceiver does not perform key operations while the
AquaQuake function is activated. The AquaQuake function can not
be activated when an optional speaker-microphone is connected.
13
 5 SCAN OPERATION (Except Holland version)

■ Scan types
Scanning is an efficient way to locate signals quickly over a Set the TAG channels (scanned channels) before scanning.
wide frequency range. The transceiver has priority scan and Clear any TAG channels which inconveniently stop scanning,
normal scan. such as digital communications.
In addition, auto scan function is available for standby conve- Choose priority or normal scan in set mode. (p. 18)
nience. This function can be activated depending on the set-
ting in set mode. (p. 18)

PRIORITY SCAN NORMAL SCAN

CH 01 CH 02 CH 01 CH 02

CH 88 CH 16 CH 03 CH 88 CH 03

CH 05 CH 04 CH 05 CH 04

Priority scan searches through all TAG channels in se- Normal scan, like priority scan, searches through all TAG
quence while monitoring Channel 16. When a signal is de- channels in sequence. However, unlike priority scan, Chan-
tected on Channel 16, scan pauses until the signal disap- nel 16 is not checked unless Channel 16 is set as a TAG
pears; when a signal is detected on a channel other than channel.
Channel 16, scan becomes dualwatch until the signal dis-
appears.
14
 SCAN OPERATION 5

■ Setting TAG channels ■ Starting a scan

For more efficient scanning, set the desired channels as TAG Set the priority scan function, scan resume timer and auto
channels or clear the TAG setting from unwanted channels. scan function in advance, using set mode. (p. 18)
Channels that are not tagged will be skipped during scanning.
TAG channels can be assigned to each channel group q Push and hold [CH] for 1 sec. several times to select the
(U.S.A., International and ATIS) independently. desired channel group, if desired. 5
w Push [SCAN] to start priority or normal scan.
q Push and hold [CH] for 1 sec. several times to select the • “SCAN” blinks in the function display.
desired channel group, if desired. • “16” appears on the sub channel readout during priority scan.
w Select the desired channel to be set as a TAG channel. • When a signal is received, scan pauses until the signal disap-
e Push and hold [TAG] (FAV) for 1 sec. to set the displayed pears or resumes after pausing 5 sec. according to the scan re-
sume timer setting. (Channel 16 is still monitored during priority
channel as a TAG channel.
scan.)
•“ ” appears in the function display.
• Push [Y]/[Z] to check which channels have been set as TAG
r To cancel the TAG channel setting, push and hold [TAG] channels, change the scanning direction or resume the scan
(FAV) for 1 sec. manually.
•“ ” disappears. e To stop the scan, push [SCAN].
• “SCAN” disappears.
✔ Clearing (or setting) all tagged channels • Pushing [PTT], [16], [CH] or [FAV] also stops the scan.
While pushing and holding [TAG] (FAV), turn power ON to
clear all TAG channels in the selected channel group.
• Repeat above procedure to set all channels as TAG channels
(when no TAG channel has been set.)

[Example]: Starting a normal scan. Scan starts When a signal is received

Push
Push

to stop the scan

15
 6 DUALWATCH/TRI-WATCH (Except Holland version)

■ Description ■ Operation
Dualwatch monitors Channel 16 while you are receiving q Select Dualwatch or Tri-watch in set mode. (p. 19)
on another channel; Tri-watch monitors Channel 16 and the w Select the desired channel.
call channel while receiving another channel. Dualwatch/Tri- e Push and hold [DUAL] (SCAN) for 1 sec. to start Dual-
watch is convenient for monitoring Channel 16 when you are watch or Tri-watch (depending on set mode setting).
operating on another channel. • “DUAL” blinks during dualwatch; “TRI” blinks during tri-watch.
• A beep tone sounds when a signal is received on Channel 16.
DUALWATCH/TRI-WATCH SIMULATION • Tri-watch becomes dualwatch when receiving a signal on the call
channel.
Call channel r To cancel dualwatch/tri-watch, push [SCAN] again.

[Example]: Operating Tri-watch on INT channel 07.

Signal is received on call
Tri-watch starts. channel.

Dualwatch Tri-watch

• If a signal is received on Channel 16, dualwatch/tri-watch

pauses on Channel 16 until the signal disappears.
• If a signal is received on the call channel during Tri-watch,
Tri-watch becomes Dualwatch until the signal disappears. Tri-watch resumes after Signal received on Channel
• To transmit on the selected channel during Dualwatch/Tri- the signal disappears. 16 takes priority.
watch, push and hold [PTT].

16
 SET MODE 7
■ Set mode programming
Set mode is used to change the settings for 11 transceiver D Set mode operation
functions: beep tone function, priority scan function, scan re- q Turn power OFF.
sume timer, auto scan function, dual/tri-watch function, moni- w While pushing [SQL], turn power ON to enter set mode.
tor key action, automatic backlighting, LCD contrast setting, • “bP” appears.
power save function, squelch sensitivity and low fix function*. e Push [SQL] or [Y Y]/[Z
Z] while pushing and holding [SQL]
*Appears only when the optional battery case is attached; Not avail- to select the desired item, if necessary.
able with German version. r Push [YY]/[ZZ] to select the desired setting of the item. 6
t To exit set mode, push [16].
7
D SET MODE ITEMS (The display shows the current settings, and the selected function is displayed in the dotted circle.)

• Low fix* • Beep tone • Priority scan† • Scan resume timer†

Starting item
• Squelch sensitivity • Auto scan†
: Push or + [Y] *Appears only when the optional
battery case is attached; Not
available with German version.
†
: Push + [Z] Not available with Holland version.

• Automatic
• Power save • LCD contrast backlighting • Monitor key action • Dual/Tri-watch†

17
 7 SET MODE

■ Set mode items

D Beep tone function “bP” D Scan resume timer “St”
Select the key touch beep sound from ON or US, or turn sound (Not available with Holland version)
OFF. The scan resume timer can be set as a pause (OFF) or timer
• US : The preset beeps (e.g. do, re, mi) sound scan (ON). When OFF is selected, the scan pauses until a
• ON : A fixed beep sounds (default) received signal disappears. When ON is selected, the scan
• OFF: Silent operation pauses for 5 sec. after receiving a signal and then resumes
even if the signal is being received.

Push
Push
Beep tone ON (default) Beep tone OFF
Scan resume timer OFF Scan resume timer ON
D Priority scan function “Pr” (default)
(Not available with Holland version)
The transceiver has 2 scan types— normal (OFF) and priority D Auto scan function “AS”
(ON) scans. Normal scan searches all TAG channels in the (Not available with Holland version)
selected channel group. Priority scan searches all TAG chan- The auto scan function starts the desired scan automatically
nels in sequence while monitoring Channel 16. when no signal is received, and no operation is performed for
30 sec.

Push
Push
Normal scan Priority scan (default)
Auto scan OFF (default) Auto scan ON

18
 SET MODE 7

D Dual/Tri-watch function “dt” D Automatic Backlighting “bL”

(Not available with Holland version) This function is convenient for nighttime operation. The back-
This item selects dual or tri-watch as desired. See p. 16 for light can be selected from ON and OFF.
details. • The backlight is automatically activated when any key except for
[PTT] is pushed.
• The backlight is automatically turned OFF after 5 sec. of inactivity.
Push

Push 7
Dualwatch function Tri-watch function
(default)
Auto backlighting ON Auto backlighting OFF
D Monitor key action “Sq” (default)
The monitor key opens the squelch temporarily. This key ac-
tion contains PUSH (Pu) or HOLD (Ho) settings as shown D LCD contrast setting “LC”
below. Set the LCD contrast level from High contrast or Low con-
• Pu (PUSH): After pushing [MONI] (SQL) for 1 sec., the squelch opens trast.
and emits audio. The squelch is held open while contin- NOTE: The LCD contrast level between High contrast and
uously pushing and holding [MONI] (SQL). (default) Low contrast makes no difference indoors.
• Ho (HOLD): After pushing [MONI] (SQL) for 1 sec., the squelch
opens and emits audio even while [MONI] (SQL) is re-
leased. To close the squelch, push any key.
Push

Push High contrast (default) Low contrast

Push setting (default) Hold setting

19
 7 SET MODE

D Power save function “PS” D Low fix function “LF”

The power save function reduces current drain by deactivat- (Appears only when the optional battery case is attached. Not avail-
ing the receiver circuit for preset intervals. able with German version.)
• ON : The power save function is turned ON. The power save func- When this function is turned ON, the output power is fixed to
tion will activate when no signal is received, and no opera- low except for channel 16.
tion is performed for 5 sec.
• OFF : The power save function is turned OFF.
Push

Push
Low fix function Low fix function ON
OFF (default)
Power save ON Power save OFF
(default)

D Squelch sensitivity “SS”

When this function is turned ON, rejection of noise is im-
proved so that the squelch is not easily affected by noise.

Push

Squelch sensitivity Squelch sensitivity

OFF (default) ON

20
 BATTERY CHARGING 8
■ Battery caution 1
R DANGER! NEVER use or leave battery pack in areas with
2
Misuse of Lithium-Ion batteries may result in the follow-
ing hazards: smoke, fire, or the battery may rupture. temperatures above +60˚C. High temperature buildup in the 3
Misuse can also cause damage to the battery or degra- battery, such as could occur near fires or stoves, inside a sun-
heated car, or by setting the battery in direct sunlight may
4
dation of battery performance.
cause the battery to rupture or catch fire. Excessive tempera- 5
tures may also degrade battery performance or shorten bat-
R DANGER! Use and charge only specified Icom battery tery life. 6
pack with Icom radios or Icom charger. Only Icom battery
pack is tested and approved for use and charge with Icom ra-
R DANGER! DO NOT expose the battery to rain, snow, sea- 7
water, or any other liquids. Do not charge or use a wet bat-
dios or Icom charger. Using third-party or counterfeit battery
tery. If the battery gets wet, be sure to wipe it dry before
8
packs or charger may cause smoke, fire, or cause the battery
to burst.
using. The battery by itself is not waterproof. 9
R DANGER! NEVER incinerate a used battery pack since 10
D Battery caution internal battery gas may cause them to rupture or may cause
an explosion. 11
R DANGER! DO NOT hammer or otherwise impact the bat-
tery. Do not use the battery if it has been severely impacted or R DANGER! NEVER solder the battery terminals, or NEVER 12
dropped, or if the battery has been subjected to heavy pres- modify the battery pack. This may cause heat generation, and
sure. Battery damage may not be visible on the outside of the the battery may rupture, emit smoke or catch fire. 13
case. Even if the surface of the battery does not show cracks R DANGER! Use the battery only with the transceiver for 14
or any other damage, the cells inside the battery may rupture which it is specified. Never use a battery with any other equip-
or catch fire. ment, or for any purpose that is not specified in this instruction
15
manual. 16
R DANGER! If fluid from inside the battery gets in your eyes,
blindness can result. Rinse your eyes with clean water, with-
out rubbing them, and see a doctor immediately.

21
 8 BATTERY CHARGING

WARNING! Immediately stop using the battery if it emits an D Charging caution

abnormal odor, heats up, or is discolored or deformed. If any
R DANGER! NEVER charge the battery pack in areas with
of these conditions occur, contact your Icom dealer or distrib-
extremely high temperatures, such as near fires or stoves, in-
utor.
side a sun-heated car, or in direct sunlight. In such environ-
WARNING! Immediately wash, using clean water, any part of ments, the safety/protection circuit in the battery will activate,
the body that comes into contact with fluid from inside the bat- causing the battery to stop charging.
tery.
WARNING! DO NOT charge or leave the battery in the bat-
WARNING! NEVER put the battery in a microwave oven, tery charger beyond the specified time for charging. If the bat-
high-pressure container, or in an induction heating cooker. tery is not completely charged by the specified time, stop
This could cause overheating, a fire, or cause the battery to charging and remove the battery from the battery charger.
rupture. Continuing to charge the battery beyond the specified time
CAUTION! Always use the battery within the specified tem- limit may cause a fire, overheating, or the battery may rup-
perature range for the transceiver (–15˚C to +55˚C) and the ture.
battery itself (–20˚C to +60˚C). Using the battery out of its WARNING! NEVER insert the battery and transceiver (bat-
specified temperature range will reduce the battery’s perfor- tery attached to the transceiver) into the charger if it is wet or
mance and battery life. soiled. This could corrode the battery charger terminals or
CAUTION! Shorter battery life could occur if the battery is left damage the charger. The charger is not waterproof.
fully charged, completely discharged, or in an excessive tem- CAUTION! DO NOT charge the battery outside of the speci-
perature environment (above +50˚C) for an extended period fied temperature range: ±0˚C to +40˚C. Icom recommends
of time. If the battery must be left unused for a long time, it charging the battery at +20˚C. The battery may heat up or
must be detached from the radio after discharging. You may rupture if charged out of the specified temperature range. Ad-
use the battery until the battery indicator shows half-capacity ditionally, battery performance or battery life may be reduced.
( ), then keep it safely in a cool dry place with the tem-
perature between –20˚C to +20˚C.

22
 BATTERY CHARGING 8

■ Supplied battery charger ■ Optional battery case 1

ï Charging connections When you would like to use the optional AAA(LR03) size bat- 2
Do not charge batteries other than the BP-252. tery case (BP-251), install the batteries as illustrated below. 3
q Attach the BC-173 to a flat surface, such as a desk, if desired. Be sure to observe the correct polarity.
w Connect the AC adapter as shown below. 4
e Insert the battery pack with/without the transceiver into the CAUTION: 5
charger. • When installing batteries, make sure they are all the
• The charge indicator lights orange. same brand, type and capacity. Also, do not mix new and 6
• The charge indicator blinks orange (or orange/green alternately) old batteries together.
when the protector is activated. • Keep battery contacts clean. It’s a good idea to clean bat-
7
r Charge the battery pack approx. 10 hours, depending on tery terminals once a week. 8
the remaining battery charge. • When using the optional battery case, output power level
• The charge indicator lights green when charging is completed. is 2 W (at high; except German version).
9
Battery pack
Transceiver NOTE: The transceiver may sink when the optional battery 10
Charge indicator
case is attached. (Depends on the weight of the installed 11
lights orange when
Turn power OFF batteries.)
the battery pack
(with/without the 12
transceiver) is in- NOTE: The battery
serted. charger, BC-173, 13
has a charging 14
timer. The timer
stops the charging 15
process after 14
hours (approx.). 16

AC adapter BC-173

Supplied
screws
23
 8 BATTERY CHARGING

■ Optional battery charger

D BC-162 installation D Charging
• To a desktop • To a wall q Connect the AC adapter as shown below.
w Insert the battery pack with/without the transceiver into the
Supplied screws Supplied screws
charger.
• The charge indicator lights orange.
• The charge indicator blinks orange (or red) when the protector
is activated.
e Charge the battery pack approx. 2 hours, depending on
the remaining battery charge.
• The charge indicator lights green when charging is completed.
NOTE: The battery charger, BC-162, has a charging
timer. The timer stops the charging process after 4
hours (approx.).
Battery pack Transceiver
• For added stability
Turn power OFF

Eyelet:
Use a rubber band to
secure the transceiver,
if desired. Charge BC-162
indicator

AC adapter
(Optional for
some versions)
24
 OPTIONAL SPEAKER-MICROPHONE 9
■ HM-165 descriptions ■ Attachment 1
Alligator type clip
Turn power OFF before attaching the speaker-microphone. 2
Then, insert the speaker-mic connector onto the [SP MIC]
To attach the speaker-mic.
connector and carefully screw it tight, as shown in the dia-
3
to your shirt or collar, etc.
gram below. Be careful not to cross-thread the connection. 4
PTT switch
Transmits during push. IMPORTANT: KEEP the transceiver’s [SP MIC] connector 5
Receives during release. cap attached when the speaker-microphone is not in use. 6
If the cover is not attached, water will get into the trans-
Microphone ceiver. Moreover, the terminals (pins) will become rusty, or 7
the transceiver will function abnormally if the connector has 8
Speaker become wet.
CAUTION: Attach the speaker-microphone’s
9
Turn the transceiver power OFF
when connecting the HM-165. connector securely to prevent accidental 10
loss, or water intrusion in the connector.
11
Detaching:
Rotate the [SP MIC] cap counter- 12
NEVER immerse the connector in water. If the connector be- clockwise (q), then detach it (w).
comes wet, be sure to dry it BEFORE attaching it to the trans- 13
w
ceiver. 14
NOTE: The microphone is located at the top of the q 15
speaker-microphone, as shown in the diagram above. To Attaching:
maximize the readability of your transmitted signal (voice), Attach the [SP MIC] cap (q), then
16
hold the microphone approx. 2.5 cm from your mouth, and rotate it clockwise completely (w).
speak in a normal voice level. q

25
 10 TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION REF.

The transceiver does • The battery is exhausted. • Recharge the battery pack. p. 23
not turn ON. • The battery pack is not attached correctly. • Attach the battery pack correctly. p. 3
No sound from speaker. • Squelch level is too high. • Set squelch to the threshold point. p. 12
• Volume level is too low. • Push [YY]/[Z
Z] after pushing [VOL] to set a p. 11
suitable level.
• Speaker has been exposed to water. • Drain water from the speaker. p. 13
Transmitting is impossi- • Some channels are for low power or re- • Change channels. pgs. 8,
ble, or high power can ceive only. 9, 27
not be selected. • The battery is exhausted. • Recharge the battery pack. p. 23
• The battery over charged. • Verify the battery voltage is correct. —
• The output power is set to low. • Push [H/L] to select high power. p. 10
The displayed channel • Lock function is activated. • Push and hold [LOCK] (H/L) for 1 sec. to p. 12
cannot be changed. cancel the function.
Scan does not start. • “TAG” channels are not programmed. • Set the desired channels as “TAG” channels. p. 15
No beeps. • Beep tone function is turned OFF. • Set the beep tone to ON (Fix Beep/User p. 18
Beep) in set mode.
Battery voltage error • The connected battery pack’s voltage is • Verify the battery voltage is correct. —
more than 11 V.

26
 VHF MARINE CHANNEL LIST 11
• International channels 1
Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz)
CH
Transmit Receive
CH
Transmit Receive
CH
Transmit Receive
CH
Transmit Receive
CH
Transmit Receive
CH
Transmit Receive 2
01 156.050 160.650 11 156.550 156.550 21 157.050 161.650 62 156.125 160.725 72 156.625 156.625 82 157.125 161.725 3
02 156.100 160.700 12 156.600 156.600 22 157.100 161.700 63 156.175 160.775 73 156.675 156.675 83 157.175 161.775
03 156.150 160.750 13 156.650 156.650 23 157.150 161.750 64 156.225 160.825 74 156.725 156.725 84 157.225 161.825 4
04 156.200 160.800 14 156.700 156.700 24 157.200 161.800 65 156.275 160.875 75*2 156.775 156.775 85 157.275 161.875
05 156.250 160.850 15*1 156.750 156.750 25 157.250 161.850 66 156.325 160.925 76*2 156.825 156.825 86 157.325 161.925 5
06 156.300 156.300 16 156.800 156.800 26 157.300 161.900 67 156.375 156.375 77 156.875 156.875 87 157.375 157.375
07 156.350 160.950 17*1 156.850 156.850 27 157.350 161.950 68 156.425 156.425 78 156.925 161.525 88 157.425 157.425
6
08 156.400 156.400 18 156.900 161.500 28 157.400 162.000 69 156.475 156.475 79 156.975 161.575 7
09 156.450 156.450 19 156.950 161.550 60 156.025 160.625 70 Rx only 156.525 80 157.025 161.625
10 156.500 156.500 20 157.000 161.600 61 156.075 160.675 71 156.575 156.575 81 157.075 161.675 8
*1 Channels 15 and 17 may also be used for on-board communications provided the effective radiated power does not exceed 1 W, and subject to the national regu-
lations of the administration concerned when these channels are used in its territorial waters.
9
*2 The use of these channels should be restricted to navigation-related communications only and all precautions should be taken to avoid harmful interference to
channel 16, e.g. by limiting the output power to 1 W or by means geographical separation. 10
• USA channels (for U.K. versions only) 11
Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz) Frequency (MHz)
CH CH CH CH CH CH 12
Transmit Receive Transmit Receive Transmit Receive Transmit Receive Transmit Receive Transmit Receive
01A 156.050 156.050 12 156.600 156.600 22A 157.100 157.100 64A 156.225 156.225 77 156.875 156.875 86 157.325 161.925 13
–– ––– ––– 13 156.650 156.650 23A 157.150 157.150 65A 156.275 156.275 78A 156.925 156.925 86A 157.325 157.325
03A 156.150 156.150 14 156.700 156.700 24 157.200 161.800 66A 156.325 156.325 79A 156.975 156.975 87 157.375 161.975 14
–– ––– ––– 15 156.750 156.750 25 157.250 161.850 67 156.375 156.375 80A 157.025 157.025 87A 157.375 157.375
05A 156.250 156.250 16 156.800 156.800 26 157.300 161.900 68 156.425 156.425 81A 157.075 157.075 88 157.425 162.025
15
06 156.300 156.300 17 156.850 156.850 27 157.350 161.950 69 156.475 156.475 82A 157.125 157.125 88A 157.425 157.425 16
07A 156.350 156.350 18A 156.900 156.900 28 157.400 162.000 70 Rx only 156.525 83A 157.175 157.175 P4* 161.425 161.425
08 156.400 156.400 19A 156.950 156.950 37A* 157.850 157.850 71 156.575 156.575 84 157.225 161.825
09 156.450 156.450 20 157.000 161.600 61A 156.075 156.075 72 156.625 156.625 84A 157.225 157.225
10 156.500 156.500 20A 157.000 157.000 –– ––– ––– 73 156.675 156.675 85 157.275 161.875
11 156.550 156.550 21A 157.050 157.050 63A 156.175 156.175 74 156.725 156.725 85A 157.275 157.275
*UK marina channels: M1=37A (Tx/Rx: 157.850 MHz), M2=P4 (Tx/Rx: 161.425 MHz) for U.K. versions only.
27
 12 SPECIFICATIONS

ï GENERAL ï RECEIVER
• Frequency coverage : Transmit 156.000–161.450 MHz • Receive system : Double-conversion
Receive 156.000–163.425 MHz superheterodyne
• Mode : FM (16K0G3E) • Sensitivity (20 dB SINAD) : –2 dBµ emf typical
• Channel spacing : 25 kHz • Squelch sensitivity : –6 dBµ emf typical (at threshold)
• Power supply requirement : BP-251 and BP-252 only • Intermodulation rejection ratio : 68 dB
• Current drain (at 7.4 V DC) : TX High (5 W) 1.5 A • Spurious response rejection ratio : 70 dB
TX Low (1 W) 0.7 A • Adjacent channel selectivity : 70 dB
Max. audio 0.2 A • Audio output power : 0.2 W at 10% distortion with an
Power save 20 mA typical 8 Ω load
• Frequency stability : ±1.5 kHz
• Useable temperature range : –15°C to +55°C
All stated specifications are subject to change without notice or
• Dimensions : 62 (W) × 141.5(H) × 43(D) mm
obligation.
(Projections not included)
• Weight : Approx. 305 g
(incl. BP-252, FA-SC58V and MB-109)

ï TRANSMITTER
• Output power (at 7.4 V DC) : 5 W (High)* and 1 W (Low)*
*1 W (High) and 0.5 W (Low) only for
German version.
• Modulation system : Variable reactance frequency
modulation
• Max. frequency deviation : ±5 kHz
• Adjacent channel power : 70 dB
• Spurious emissions : 0.25 µW

28
 OPTIONS 13
D BATTERY CASE AND PACK 1
• BP-251 BATTERY CASE
Battery case for 5 × AAA (LR03) alkaline cells. 2
Output power level: 2 W (except for German version)
• BP-252 Li-Ion BATTERY PACK 3
7.4 V/980 mAh Li-Ion battery pack. 4
D CHARGERS 5
• BC-173 DESKTOP CHARGER + BC-174E/BM-95V AC ADAPTER
Used for regular charging of battery pack. An AC adapter is supplied
6
with the charger depending on versions. 7
Charging time: approx. 10 hours
• BC-162 DESKTOP CHARGER + BC-145* AC ADAPTER 8
Used for rapid charging of battery pack.
Charging time: approx. 2 hours. 9
*Not supplied with some versions. 10
D BELT CLIPS 11
• MB-109 BELT CLIP
The same as supplied with the transceiver.
12
13
D OTHER OPTIONS
• HM-165 SPEAKER-MICROPHONE 14
Full sized waterproof (IPX7; 1m/30 min.) speaker-microphone. In-
cludes an alligator clip to attach the speaker mic to your shirt, collar,
15
etc. 16
• FA-SC58V ANTENNA FOR IC-M33

29
 <Intended Country of Use>
■ GER ■ FRA ■ ESP ■ SWE
■ AUT ■ NED ■ POR ■ DEN
■ GBR ■ BEL ■ ITA ■ FIN
■ IRL ■ LUX ■ GRE ■ SUI
■ NOR

A-6545H-1EU
Printed in Japan
© 2007 Icom Inc.
Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan