International Journal of Manufacturing & Industrial Engineering – IJMIE

Volume 1: Issue 1 [ISSN: 2374 -1589]

Publication Date : 09 January 2014

Metallurgy of Continuous Casting Technology

Dr.T.R.Vijayaram PhD
Professor in Mechanical Engineering
School of Mechanical and Building Sciences SMBS
VIT University Chennai Campus
Vandalur-Kelambakkam Road
Chennai 600127 Tamil Nadu South India
India
E-mail: vijayaram.tr@vit.ac.in
In continuous casting process metal is melted in a furnace and transferred in a tundish.
Pouring is accomplished through ceramic piping, and the tundish is covered to prevent
oxidation of the metal. From the tundish, it is released into a mould. As the metal cools
and solidifies, usually aided with water cooling systems, which surround the mould,
finished cast metal protrudes from the far end of the mould. Torches can be used to cut
the metal off at set lengths as desired. This presentation discusses on the continuous
casting process description, mechanism, and control, hydrodynamics, heat transport,
thermal analysis, solidification control and heat transfer, continuous cast product types,
range of sections, and advantages of continuous casting technology for ferrous and non-
ferrous foundries.

Keywords: tundish, metallurgical length, solidification, macrostructure, hydrodynamics,

heat transport, centreline segregation.

INTRODUCTION

Continuous casting technology is most effective, if it is necessary to manufacture semi-

finished products of standardized form in large series. This method also provides
increased control over the process through automation [1]. Equal and continuous supply
of metal, its crystallization and removal of the product allows obtaining a homogeneous
semi-finished metal product during the casting process. With intensified cooling with
water, it is possible to increase the speed of crystallization [2]. By choosing the right
speed, focused crystallization in the material is achieved and a fine structure of crystals
with an even chemical composition is produced. Continuous casting allows producing a
wide range of different profiles: cylindrical bares, tubes, square bares and tubes,
hexagonal profiles, slabs of various thickness and width [3].

CONTINUOUS CASTING PRINCIPLE

The continuous casting process is used to overcome a number of ingot-related difficulties
such as piping, mold spatter, entrapped slag and structure variation along the length of the
product. It is used to produce blooms, billets, slabs and tubing directly from the molten
metal. In this process, molten metal flows into a refractory-lined intermediate pouring
vessel, where impurities are skimmed off [4]. From there, the metal travels through a
bottomless water-cooled copper mold in the form of a vertical tube open at both ends and

17
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

begins to solidify as it travels downward along a path supported by rollers. A schematic

sketch of the continuous casting process is shown below in Figure-1.

Figure-1 Schematic sketch to illustrate the principle of continuous

casting process
Direct water sprays to produce complete solidification then cool the metal. The cast solid
is still hot and is either bent or fed horizontally through a short reheat furnace, which
makes it perfectly straight. Hollow rods or thick-walled tubing is made by placing a
graphite core centrally in the mold to a depth below the level at which solidification is
complete. The continuously cast metal may be cut into desired lengths with a torch or a
circular saw. It may also be fed directly into a rolling mill for further reduction in
thickness and for shape rolling of products such as channels and I-beams. The high
pouring temperature requirement in the preparation of steel offers difficulties in the
design of mold. The slow solidification rate of steel and the high casting speed make it
necessary to have long dies. This increases the chance for bulging of the cast shape due to
the deep liquid core [5]. This process is applied to copper and copper alloys, aluminium,
steel, grey cast iron, and alloy cast iron. Typical parts made by continuous casting process
are tubes, slabs, and gears. These products are obtained by cutting the continuous strand
to the required size. Strand can be of rectangular or circular cross-sections.

HORIZONTAL CONTINUOUS CASTING PLANTS IN FOUNDRIES

18
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

An industrial horizontal continuous casting plant is shown below in Figure-2. It explains

the processing of rod casting and strip casting, which is self-explanatory.

Figure-2 Horizontal continuous casting plant

These processes are the most efficient way to solidify large volumes of metal into simple
shapes for subsequent processing. Most basic metals are mass-produced using a
continuous casting process, including over 500 million tons of steel, 20 million tons of
aluminium, and 1 million tons of copper, nickel, and other metals in the world each year.
Continuous casting is distinguished from other solidification processes by its steady state
nature, relative to an outside observer in a laboratory frame of reference. The molten
metal solidifies against the mould walls while it is simultaneously withdrawn from the
bottom of the mould at a rate, which maintains the solid-liquid interface at a constant
position with time. The process works best when all of its aspects operate in this steady-
state manner [6].

19
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

Relative to other casting processes, continuous casting generally has a higher capital cost,
but lower operating cost. It is the most cost- and energy- efficient method to mass-
produce semi finished metal products with consistent quality in a variety of sizes and
shapes. Cross-sections can be rectangular, for subsequent rolling into plate or sheet,
square or circular for long products, and even “dog-bone” shapes, for rolling into I or H
beams. Many different types of continuous casting processes exist. Vertical machines are
used to cast aluminium and a few other metals for special applications. Curved machines
are used for the majority of steel casting and require bending and or unbending of the
solidifying strand. Horizontal casting features a shorter building and is used occasionally
for both nonferrous alloys and steel. Finally, thin strip casting is being pioneered for steel
and other metals in low-production markets in order to minimize the amount of rolling
required [7].

DESCRIPTION OF CONTINUOUS CASTING PROCESS

In the continuous casting process, molten metal is poured from the ladle into the tundish
and then through a submerged entry nozzle into a mould cavity. The mould is water
cooled so that enough heat is extracted to solidify a shell of sufficient thickness. The shell
is withdrawn from the bottom of the mould at a "casting speed" that matches the inflow of
metal, so that the process ideally operates at steady state. Below the mould, water is
sprayed to further extract heat from the strand surface, and the strand eventually becomes
fully solid when it reaches the ''metallurgical length''. Solidification begins in the mould,
and continues through the different zones of cooling while the strand is continuously
withdrawn at the casting speed. Finally, the solidified strand is straightened, cut, and then
discharged for intermediate storage or hot charged for finished rolling [8]. Continuous
casting process details are shown below in Figure-3(a) and Figure-3(b).

To start a cast, a steel dummy bar seals the bottom of the mould. This bar prevents liquid
metal from flowing out of the mould and the solidifying shell until a fully solidified
strand section is obtained. The liquid poured into the mould is partially' solidified in the
mould, producing a strand with a solid outer shell and a liquid core. In this primary
cooling area, once the steel shell has a sufficient thickness, the partially solidified strand
will be withdrawn out of the mould along with the dummy bar at the casting speed.
Liquid metal continues to pour into the mould to replenish the withdrawn metal at an
equal rate. Upon exiting the mould, the strand enters a roller containment section and
secondary cooling chamber in which the solidifying strand is sprayed with water, or a
combination of water and air referred as "air-mist" to promote solidification. Once the
strand is fully solidified and has passed through the straightener, the dummy bar is
disconnected, removed and stored [9].

20
International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

Figure-3 (a) Schematic Sketch of Continuous Casting Process

21
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

Figure-3 (b) Schematic Sketch of Continuous Casting Process with Straightening

Rolls and Cutting Torch

22
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

The shape of the tundish is typically rectangular. Nozzles are located along its bottom to
distribute liquid steel to the mould. The tundish also serves several other key functions
such as to enhance oxide inclusion separation, to provide a continuous flow of liquid steel
to the mould during ladle exchanges, to maintain a steady metal height above the nozzles
to the mould, thereby keeping steel flow uniform and also to provide more stable stream
patterns to the mould. The main function of the mould is to establish a solid shell
sufficient in strength to support its liquid core upon entry into the secondary spray-
cooling zone. The mould is an open-ended box structure, containing a water-cooled inner
lining fabricated from a high purity copper alloy. The inner face of the copper mould is
often plated with chromium or nickel to provide a harder working surface, and to avoid
copper pickup on the surface of the cast strand, which can otherwise facilitate surface
cracks on the product. Mould oscillation is necessary to minimize friction and sticking of
the solidifying shell, and avoid shell tearing, and liquid steel breakouts, which can wreak
havoc on equipment and machine downtime due to clean up and repairs. Friction between
the shell and mould is reduced with mould lubricants such as oils or powdered fluxes.
Oscillation is achieved either hydraulically or via motor-driven cams or levers which
support and reciprocate or oscillate the mould [10].

STARTER BAR
Continuous casting process with a starter bar is shown below in Figure-4. The starter bar
has a free end portion, which is flexible for storage, and a substantially rigid portion at the
end, which plugs the mould [11].

Figure-4 Continuous Casting Process with a starter bar

23
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

The starter bar is constructed in discrete blocks secured to one side of a planar spine
provided in segments and arranged end to end. Adjustable spacers in the form of tapered
blocks are disposed between the blocks of the bar to allow the starter bar to be self-
supporting in a curved configuration corresponding to the casting path. A more flexible
spine in the end portion of the starter bar allows the starter bar to be curved to a tighter
radius than that of the casting path while the blocks fan out in an unsupported
configuration. A storage ramp is provided to support the flexible end in the stored
position [12].

CONTINUOUS CASTING PROCESS CONTROL

The mechanism of continuous casting process is shown below in Figure-5(a). Starting a
continuous casting machine involves placing a dummy bar, essentially a curved metal
beam, up through the spray chamber to close off the base of the mould. Metal is poured
into the mould and withdrawn with the dummy bar once it solidifies. It is extremely
important that the metal supply afterwards be guaranteed to avoid unnecessary shutdowns
and restarts, known as 'turnarounds'.

Each time the caster stops and restarts a new tundish is required, as any uncast metal in
the tundish cannot be drained and instead freezes into a 'skull'. Avoiding turnarounds
requires the melt shop, including ladle furnaces to keep tight control on the temperature
of the metal, which can vary dramatically with alloying additions, slag cover and
deslagging, and the preheating of the ladle before it accepts metal, among other
parameters [1].

However, the castrate may be lowered by reducing the amount of metal in the tundish,
although this can increase wear on the tundish, or if the caster has multiple strands, one or
more strands may be shut down to accommodate upstream delays. Turnarounds may be
scheduled into a production sequence if the tundish temperature becomes too high after a
certain number of heats.

Many continuous casting operations are now fully computer-controlled. Several

electromagnetic and thermal sensors in the ladle shroud, tundish and mould sense the
metal level or weight, flow rate and temperature of the hot metal, and the programmable
logic controller, PLC can set the rate of strand withdrawal via speed control of the
withdrawal rolls. The flow of metal into the moulds can be controlled by two methods:

 By slide gates or stopper rods at the top of the mould shrouds

 If the metal is open-poured, then the metal flow into the moulds is controlled solely
by the internal diameter of the metering nozzles. These nozzles are usually
interchangeable.

Overall casting speed can be adjusted by altering the amount of metal in the tundish,
through the ladle slide gate. The PLC can also set the mould oscillation rate and the rate
of mould powder feed, as well as the spray water flow. Computer control also allows vital
casting data to be repeated to other manufacturing centres particularly the steelmaking
furnaces, allowing their work rates to be adjusted to avoid 'overflow' or 'underrun' of
product [1,2].

24
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

Figure-5(a) Mechanism of Continuous Casting Process

While the large amount of automation helps produce castings with no shrinkage and little
segregation, continuous casting is of no use if the metal is not clean beforehand, or
becomes 'dirty' during the casting process. One of the main methods through which hot

25
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

metal may become dirty is by oxidation, which occurs rapidly at molten metal
temperatures (up to 1700 °C); inclusions of gas, slag or undissolved alloys may also be
present. To prevent oxidation, the metal is isolated from the atmosphere as much as
possible. To achieve this, exposed metal surfaces are covered by the shrouds, or in the
case of the ladle, tundish and mould, by synthetic slag. In the tundish, any inclusions in
the form of gas bubbles, other slag or oxides, or undissolved alloys may also be trapped in
the slag layer [6, 8].

A major problem that may occur in continuous casting is breakout. This is when the thin
shell of the strand breaks, allowing the still-molten metal inside the strand to spill out and
foul the machine, requiring a turnaround. Often, breakout is due to too high a withdrawal
rate, as the shell has not had the time to solidify to the required thickness, or the metal is
too hot, which means that final solidification takes place well below the straightening
rolls and the strand breaks due to stresses applied during straightening. A breakout can
also occur if solidifying steel sticks to the mould surface, causing a tear in the shell of the
strand. If the incoming metal is overheated, it is preferable to stop the caster than to risk a
breakout. Additionally, lead contamination of the metal caused by counterweights or
lead-acid batteries in the initial steel charge can form a thin film between the mould wall
and the steel, inhibiting heat removal and shell growth and increasing the risk of
breakouts [1, 8].

Another problem that may occur is a carbon boil, i.e., oxygen dissolved in the steel reacts
with also-present carbon to generate bubbles of carbon monoxide. As the term boil
suggests, this reaction is extremely fast and violent, generating large amounts of hot gas,
and is especially dangerous if it occurs in the confined spaces of a casting machine.
Oxygen can be removed through the addition of silicon or aluminium to the steel, which
reacts to form silicon oxide (silica) or aluminium oxide (alumina). However, too much
alumina in the steel will clog the casting nozzles and cause the steel to 'choke off'.

Computational fluid dynamics and other fluid flow techniques are being used extensively
in the design of new continuous casting operations, especially in the tundish, to ensure
that inclusions and turbulence are removed from the hot metal, yet ensure that all the
metal reaches the mould before it cools too much. Slight adjustments to the flow
conditions within the tundish or the mould can mean the difference between high and low
rejection rates of the product [1, 9, 14]

CONTINUOUS CASTING HYDRODYNAMICS

The motion that is generated in a metal melt at casting and solidification is important for
casting material properties and for the reduction of serious casting defects. The flow in
the melt is generated at the teeming processes from ladle to mold when the melt is forced
to pass a so-called gating system. An incorrect design of the outlet hole in the ladle or of
the gating system may cause serious defects such as cold shuts, and numerous macro slag
inclusions. In addition, flow of melt is also developed during the solidification process in
the form of natural convection, which arises due to temperature or concentration
differences in the melt. This flow influences the structure of the material and its physical
properties. Experiments have shown that the same laws of hydrodynamics area as valid
for molten metals as for other fluids. The result is that the laws of hydrodynamics can be
applied to the continuous casting of metals. The principle of continuity and Bernoulli’s
equation are the two important laws taken from fluid mechanics are applied to the

26
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

continuous casting of metals and alloys [1]. In continuous casting, a water-cooled metal-
mold is used to provide strong and effective cooling of the strand. The solidificied shell of
the strand must have enough stability and strength before leaving the chill-mold. A
tundish is always used between the ladle and the chill-mold to achieve a constant pressure
of the melt at the entrance to the chill-mold. A straight vertical sprue, similar to a casting
tube or a submerged entry nozzle between the tundish and the chill-mold is used in
continuous casting. The casting tube reduces casting defects such as macro slag
inclusions.

The aim of the tundish is to provide a constant casting speed. In this process, it is
desirable to have the most even velocity of the casting that can be obtained. By the use of
a tundish as an intermediate container between the ladle and the chill-mold, the
disadvantage of the velocity of the melt varying with the height of the melt in the ladle is
eliminated. The tundish is kept filled and the distance between the tundish and the chill-
mold is constant. A sliding gate or a stopper rod controls the flow from the tundish.
Flushing with argon gas is performed often to prevent air intrusion or clogging of the
nozzle [1, 2, 3].

Another problem is the risk of slag inclusions. To decrease the problem of macro slag
inclusions, the upper surface of the melt is covered with casting-powder and the melt
transformed from the tundish to the mold through a submerged entry nozzle or casting
tube. The flow depends on the geometry, depth and dimensions of the nozzle exit and the
flow rate of the jet. The jet causes forced convection in the chill-mold in addition to
natural convection that is always present during solidification. To avoid inclusion of
trapped slag particles at the solidification front, the penetration depth should be moderate.
Therefore, the nozzles often designed with exits on the sides at some angle between zero
degree and ninety degree relative to the vertical axis. The casting tube must be made of a
material that resists chemical attacks from steel alloying elements, such as aluminium,
sulphur, and manganese. Casting tubes are often made of a mixture of aluminium oxide
and graphite. The melt flow in the mold is greatly influenced by the jets from the casting
tube. The superheated melt leaves the nozzle and it impinges laterally into the mold, splits
into two strongly circulating flows are directed upwards and the other one is directed
downwards. The violent motion in the melt contributes strongly to the formation of a
homogeneous fluid.

HEAT TRANSPORT IN CONTINUOUS CASTING

Casting of metals is closely related to heat release and heat transport during solidification
and cooling. The rate of heat removal is very important as it determines the solidification
time of the casting and the temperature distribution in the material. These control directly
or indirectly the structure of the material, precipitation of pores and slag inclusions and
distribution and shape of shrinkage of pores, and hence the qualities and properties of
castings. In the case of solidifying metal melts, thermal conduction will be the most
important way of heat transport. Continuous casting is based on casting of a metal in a
vertical chill-mold [1, 9]. The metal flows from the ladle via the tundish down into the
vertical, water-chilled copper mold. During the passage into the chill-mold, the melt starts
to solidify and a solid shell is formed. This shell is drawn continuously out of the chill-
mold into the chill-zone where complete solidification occurs. The velocity of the shell is
called as casting velocity or casting rate. A necessary condition for continuous casting is
that the shell has such mechanical properties that are rigid outside the chill-mold. Water-

27
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

cooling is therefore very important in this process. Continuous casting is a typical

example of heat transport with poor contact between the chill-mold and metal. To obtain
maximum yield, the highest possible production velocity is required. This demands
careful control of the cooling and casting conditions. With poor contact between the mold
and the metal, there is a discontinuity of the temperature at the interface.

SOLIDIFICATION CONTROL IN CONTINUOUS CASTING OF

STEEL
Solidification in continuous casting technology is initiated in a water-cooled, open-ended
copper mould. The steel shell, which forms in the mould, contains a core of liquid steel,
which gradually solidifies as the strand moves through the caster guided by a large
number of roll pairs. The solidification process initiated at meniscus level in the mould is
completed in secondary cooling zones using a combination of water spray and radiation
cooling. Solidification speciality of continuous casting technology arises from the
dynamic nature of the casting process.

In particular this relates to handling of very high heat flux in the mould, nurturing of the
initial thin and fragile solid shell for avoidance of breakout during descent of the strand
down the mould, designing of casting parameters in tune with the solidification dynamics
of the steel grade for minimisation or elimination of surface and internal defects in the
cast product. Safe caster operation, i.e., without metal breakout and achievement of
acceptable product quality require understanding of both process engineering and
metallurgy of solidification. Early solidification in continuous casting occurs in the form
of partial freezing of the meniscus curvature originating from the mould liquid contact
point. To minimise shell sticking and tearing, friction between the strand surface and
mould wall must be kept below a critical level depending upon the shell strength.
Minimisation of the friction and continuous release of the shell from the mould have been
achieved through the introduction of mould oscillation aided by lubrication [1, 2, 4].

HEAT TRANSFER IN CONTINUOUS CASTING

By its nature, continuous casting is primarily a heat-extraction process. The conversion of
molten metal into a solid semi-finished shape involves the removal of the following forms
of heat.

 Superheat from the liquid entering the mould from the tundish.
 The latent heat of fusion at the solidification front as liquid is transformed solid, and
finally.
 The sensible heat, i.e., cooling below the solidus temperature from the solid shell.

These heats are extracted by a combination of the following heat-transfer mechanisms:

 Convection in the liquid pool.

 Heat conduction down temperature gradients in the solid shell from the
solidification front to the colder outside surface of the cast.
 External heat transfer by radiation, conduction and convection to
surroundings.

28
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

Because heat transfer is the major phenomenon occurring in continuous casting, it is also
the limiting factor in the operation of a casting machine. The distance from the meniscus
to the cut-off stand should be greater than the metallurgical length, which is dependent on
the rate of heat conduction through the solid shell and of heat extraction from the outside
surface, in order to avoid cutting into a liquid core. Thus, the casting speed must be
limited to allow sufficient time for the heat of solidification to be extracted from the
strand [1]. Heat transfer not only limits maximum productivity but also profoundly
influences cast quality, particularly with respect to the formation of surface and internal
cracks. In part, this is because metals expand and contract during periods of heating or
cooling. That is, sudden changes in the temperature gradient through the solid shell,
resulting from abrupt changes in surface heat extraction, causes differential thermal
expansion and the generation of tensile strains. Depending on the magnitude of the strain
relative to the strain-to-fracture of the metal and the proximity' of the strain to the
solidification front, cracks may form in the solid shell. The rate of heat extraction also
influences the ability of the shell to withstand the bulging force due to the ferrostatic
pressure owing to the effect of temperature on the mechanical properties of the metal.
Therefore, heat transfer analysis of the continuous casting process should not be
overlooked in the design and operation of a continuous casting machine.

MACROSTRUCTURES IN CONTINUOUSLY CAST MATERIALS

The microstructure of a continuously cast material resembles the macrostructure found in
ingots. The formation mechanisms of the crystal types and crystal zones are same in both
cases, and the discrepancies that appear originate from the different casting conditions.
The growth of macrostructure in a continuously cast product is shown below in Figure-6
[13].

Figure-6 shows the macrostructure of a slab cast in a continuous casting

machine [13]

29
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

Figure-7 Macrostructure of continuously cast Al–1.2Li–0.8 Hf alloy ingot.

(a) Top, (b) Middle and (c) Bottom parts [14]
Figure-7 show the macrostructure of the continuously cast Al–1.2Li–0.8Hf alloy ingot for its
top, middle and bottom parts, respectively. The bottom part is first cast section and it is
composed of columnar grain, elongated in the cast direction, and formed from the outer
surface to the centre of ingot [14]. Finer equiaxed grains are observed in the central part of

30
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

ingot. This solidification pattern is similar to that found in the pure aluminum ingot, but this
one revealed a grain size larger than that found in the Al–1.2Li–0.8Hf alloy [14].

Figure-8 Macrostructure of a continuously cast stainless steel bloom

The above Figure-8 shows the macrostructure of a continuously cast stainless steel
bloom. The size, shape and the orientation of the grains reveal two distinct zones:

 A central region of fine randomly oriented equiaxed grains

 An outer region of columnar grains, elongated normal to the ingot surface.
Careful examination shows that their width increases from the surface to the
centre.
 A third zone, corresponding to very fine chill crystals, is present at the extreme
skin.

SOLIDIFICATION AND COOLING SHRINKAGE DURING

CONTINUOUS CASTING
During continuous casting, the melt must be strongly cooled since no metal must be left
inside the strand, when it leaves the machine. If the walls and bottom of a chill-mold are
strongly cooled, a large temperature gradient is formed in the melt. The dendrites grow
mainly in the direction of the temperature gradient and the shrinkage cavities appear in
the shape of a narrow pipe in the centre [1, 2].

Corresponding cooling conditions with strong temperature gradients are also valid during
continuous casting, when the walls of the strand are cooled by water spraying in the
chilled zone below the chill-mold. Pipe formation appears at the end of the solidification
of the strand when the supply of new melt from the tundish has ceased. Figure-9 shown
above is a schematic sketch of an axial section of a continuous cast ingot.

31
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

Figure-9 Schematic sketch of an axial section of a continuously cast

ingot
In continuous casting, melt is continuously added to the mold and the volume decrease
due to solidification and cooling shrinkage is thus compensated. Then situation is
changed at the end of the casting process when the supply of melt from the tundish above
the mold ceases. The pipe volume can be reduced by different practical methods and is in
most cases not a major problem in continuous casting process. However, the mechanism
of pipe formation in a continuously cast strand is the same that of centreline segregation,
which is a severe problem. The pipe is well developed in billets but less marked in casting
of slabs. The reason for this difference is found in the design of the casting machine and
the casting conditions in the two cases. Experimental examinations show that the pipe
volume during continuous casting is so large that it cannot be explained entirely by
solidification shrinkage. The central cavities in continuous casting are caused by
combined solidification and cooling shrinkage.

CENTRE SEGGREGATION DURING CONTINUOUS CASTING

Figure-10 show the features of macro segregation in longitudinal section of continuously

cast billets [13]. Centre segregation in continuous casting process is caused like pipe
formation, by solidification and cooling shrinkage. Melt flow through a two-phase region

32
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

and fills the cavity, which is caused by the shrinkage at the centre. Simple and closely
packed V-segregations appear in the region above and below bridges across the pipes.

Figure-10 Features of macro segregation in longitudinal section of

continuously cast billets [13]
Centre segregation and pipe formation in continuous casting can be minimised by the
following methods:

 Reduction of the casting rate during the final stage of the casting.
 Application of an external pressure on the strand at an optimal distance from the
mold.
 No interruption of the pressure treatment until the strand has solidified
completely.
 Design of the secondary cooling in an optimal way; additional cooling from a
certain optimal position is favourable.

CONTINUOUSLY CAST SECTIONS

 Casting machines are designated to be billet, bloom or slab casters.
 Slab casters tend to cast sections with an aspect ratio that is much wider than it is
thick:
o Conventional slabs lie in the range 100–1600 mm wide by 180–250 mm thick
and up to 12 m long with conventional casting speeds of up to 1.4 m/minute.
o Wider slabs are available up to 3250×150 mm.
o Thick slabs are available up to 2200×450 mm.
o Thin slabs: 1680×50 mm
 Conventional bloom casters cast sections above 200×200 mm. Casts sections of
560×400 mm. The bloom length can vary from 4 m to 10 m.
 Billet casters cast smaller section sizes, such as below 200 mm square, with lengths
up to 12 m long. Cast speeds can reach up to 4 m/minute.
 Rounds: either 500 mm or 140 mm in diameter

33
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

 Conventional beam blanks: look similar to I-beams in cross-section; 1048×450 mm or

438×381 mm overall.
 Near net shape beam blanks: 850×250 mm overall
 Strip: 2–5 mm thick by 760–1330 mm wide

CONTINUOUSLY CAST PRODUCTS

Depending on the design of the casting machine, the as-cast products of the continuous
cast process are slabs, blooms, billets, or beam blanks. The cross sections of these
products are shown below in Figure-11.

Figure-11 Continuously Cast Products

Billets have cast section sizes up to about 200 mm square. Bloom section sizes typically
range from approximately 200 mm to 400 mm by 600 mm. Round billets include
diameters of approximately 140 mm to 500 mm. Slab castings range in thickness from 50
mm to 400 mm, and over 2500 mm wide. The aspect ratio (width-to-thickness ratio) is
used to determine the dividing line between blooms and slabs. An aspect ratio of 2.5:1 or
greater constitutes an as-cast product referred to as a slab.

ADVANTAGES OF CONTINUOUS CASTING TECHNOLOGY

 Reduced cost and improved quality.

 Less variability in chemical composition both along the thickness and along
the length and surface has fewer defects.
 Increased yield, since it is not necessary to crop the ends of continuously cast
slabs and reduced energy costs.
 The slabs are sent directly to hot rolling and do not require pits for reheating
and also the thickness of continuously cast slabs is half the thickness of ingot
castings and thus require lower energy for hot rolling.
 Less pollution and the dimensions produced in continuous castings are more
amenable for hot rolling.
 In continiuos casting process, the ladle has to move short distance i.e. only
over the tundish and not over every mould.

34
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

 Continuous casting is perfect for manufacturing semi-finished products (bars,

slabs) of long sizes;
 The microstructure of long semi-finished products is even and due to this there
is less possibility for arising of tension in the product and the finished parts
made from such products will be more durable;
 Continuous casting reduces metal cuttings and loss of metal compared to
casting in moulds. It is economic regarding the energetic consumption and
there are fewer workers needed at the production process compared to casting
in moulds.

CONCLUSION

Continuous casting transforms molten metal into solid on a continuous basis and includes
a variety of important commercial processes. Continuous casting technology is a
metalworking process in which metal is cast continuously, rather than being cast in
discrete molds. This process is extremely efficient and cost effective, making it popular
for the production of a variety of semi finished metal shapes. Once cast, the metal can be
further worked as needed. All operations can be easily automated and supervised. It is
easy to modify the quality and properties of the semi-finished products by changing the
cast parameters like the pulling speed of the product, the temperature of the crystallizer’s
water. Continuous casting allows manufacturing metal slabs or bars in large amounts by
short time.

Acknowledgement

The author expresses his thanks and gratitude to the School of Mechanical and Building
Sciences, SMBS, VIT University, Chennai Campus, Chennai 600127, India.

REFERENCES
1. Hasse Fredriksson and Ulla Akerlind, Materials Processing During Casting, John
Wiley & Sons, Ltd, West Sussex, England, 2006.
2. D.K.Singh, Fundamentals of Manufacturing Engineering, CRC Press, Taylor and
Francis Group, USA, 2008.
3. M.M. Wolf, "History of Continuous Casting," in Steelmaking Conference
Proceedings,75, Iron & Steel Society, Warrendale, PA, USA, 1992.

4. H.F. Schrewe, Continuous Casting of Steel, Fundamental Principles and Practice,

(Stahl und Eisen, Dusseldorf, Germany, 1991.

5. Thomas, B. G., “Continuous Casting: Modeling”, The Encyclopedia of Advanced

Materials (Dantzig, J., Greenwell, A., Michalczyk, J., eds.), Pergamon Elsevier Science
Ltd., Oxford, UK, Vol. 2, 1999.

6. Mechanical Engineer's Reference Book, 12th Edition. Edited by E.H. Smith. Published
by Elsevier, Amsterdam, 1998.

35
 International Journal of Manufacturing & Industrial Engineering – IJMIE
Volume 1: Issue 1 [ISSN: 2374 -1589]
Publication Date : 09 January 2014

7. T Frederick Walters, Fundamentals of Manufacturing for Engineers. Taylor & Francis,

London, 2001.

8. S Mazumdar and S K Ray, Solidification control in continuous casting of steel,

Sadhana, India, Vol. 26, Parts 1 & 2, February–April 2001, pp. 179–198.

9. Hoedle H, Frauenhuber K, Moerwald K 1999-Advanced equipment for high

performance Casters, Steelmaking Conference Proceedings, vol. 82, pp. 141–151.

10. Saucedo I G 1991 Early solidification during continuous casting of steel.

Steelmaking Conference. Proc. (Warrendale, PA: Iron & Steel Soc.) vol. 74, pp 79–89

11. Choudhary, K. and Mazumdar, Dipak, “Mathematical modeling of fluid flow, heat
transfer and solidification phenomena in continuous casting of steel”, Steel Research, 66,
No. 5, 1995.

12. Belete Kiflie and Dr.-Ing. Demiss Alemu, Thermal analysis of continuous casting
process, Journal of the Ethiopian Society of Mechanical Engineers, ESME 5th Annual
Conference on Manufacturing and Process Industry, Addis Ababa, Ethiopia, September
2000.

13. A. Ghosh, Segregation in cast products, Sadhana, Vol. 26, Parts 1 & 2, February–
April 2001, pp. 5–24

14. Tomas Rangel-Ortiz, Federico Chavez Alcala, Victor M. López Hirata, Jose Frias-
Flores, Jorge E. Araujo-Osorio, Hector J. Dorantes-Rosales, Maribel L. Saucedo-Muñoz,
Microstructure and tensile properties of a continuous-cast Al–Li–Hf alloy, Journal of
Materials Processing Technology, Science Direct, Elsevier, 159 (2005) 164–168

36