TA-COMPACT-P – NPT threads

Combined control & balancing

valves for small terminal units
Pressure independent balancing
and control valve (PIBCV)
IMI TA / Control valves / TA-COMPACT-P – NPT threads

TA-COMPACT-P
– NPT threads
The pressure independent balancing and control valve TA-COMPACT-P
ensures optimum performance over a long life. Adjustable maximum
flow enables design flow and eliminates over flows for accurate
hydronic control. The TA-COMPACT-P together with our balancing
instruments enables advanced measuring and diagnostics.

Key features
>> Precise hydronic balancing >> Full control of the system
Smoothly adjustable setting of max. Exact flow measuring and unique
flow prevents over flow through diagnostic functions for ultimate
terminal unit. energy savings and highly reliable
system.
>> Installations without limits
Slim and compact shape simplifies >> High reliability
installation, one side access to all AMETAL® and stainless steel
functions simplifies operation. guarantees high corrosion resistance
and reduces the risk of leakage.

Technical description

Application: Flow range: Material:

Heating and cooling systems. The flow (qmax) can be set within the Valve body: AMETAL®
range: Valve insert: AMETAL®
Functions: DN 10: 21,5 - 120 l/h Valve plug: Stainless steel
Control DN 15 LF: 44 - 245 l/h Spindle: Stainless steel
Pre-setting (max. flow) DN 15: 88 - 470 l/h Spindle seal: EPDM O-ring
Differential pressure control DN 20: 210 - 1150 l/h Δp insert: PPS
Measuring (ΔH, T, q) DN 25: 370 - 2150 l/h Membrane: EPDM and HNBR
Isolation (for use during system DN 32: 800 - 3700 l/h Springs: Stainless steel
maintenance – see also Leakage rate) qmax = l/h at each setting and fully open O-rings: EPDM
valve plug.
Dimensions: LF = Low flow AMETAL® is the dezincification resistant
DN 10-32 alloy of IMI Hydronic Engineering.
Temperature:
Pressure class: Max. working temperature: 90°C Marking:
PN 16 Min. working temperature: -10°C TA, IMI, PN 16, DN and flow direction
arrow.
Differential pressure (ΔpV): Media: Grey handwheel: TA-COMPACT-P and
Max. differential pressure (ΔpVmax): Water or neutral fluids, water-glycol DN. For low flow version also LF.
400 kPa = 4 bar mixtures (0-57%).
Min. differential pressure (ΔpVmin): Connection:
DN 10-20: 15 kPa = 0,15 bar Lift: Male thread according to ISO 228.
DN 25-32: 23 kPa = 0,23 bar 4 mm Connections (accessories) with female
(Valid for position 10, fully open. Other and male threads NPT according to
positions will require lower differential Leakage rate: ANSI/ASME B1.20.1-1983, or for
pressure, check with the software Leakage flow ≤ 0,01% of max. qmax soldering according to ASME/ANSI
HySelect.) (setting 10) and correct flow direction. B16.18.
ΔpVmax = The maximum allowed pressure (Class IV according to EN 60534-4).
drop over the valve, to fulfill all stated Connection to actuator:
performances. M30x1,5
ΔpVmin = The minimum recommended
pressure drop over the valve, for proper Actuators:
differential
2 pressure control. See separate information on EMO T.
Measuring accuracy
Maximum flow deviation at different settings
±%
24
22
20
18
16
14
12
10
8
6
4
2
0
0 10 20 30 40 50 60 70 80 90 100
[%] *

*) Setting (%) of fully open valve.

Correction factors
The flow calculations are valid for water (+20°C). For other a flow deviation that increases with small valves, low settings
liquids with approximately the same viscosity as water and low differential pressures. Correction for this deviation can
(≤20 cSt = 3°E=100S.U.), it is only necessary to compensate for be made with the software HySelect or directly in our balancing
the specific density. However, at low temperatures, the viscosity instruments.
increases and laminar flow may occur in the valves. This causes

Noise
In order to avoid noise in the installation the valve must be
correctly installed and the water de-aerated.

Actuators
Actuator EMO T Max. recommended pressure drop (ΔpV) for valve and
For more details of EMO T, see separate catalogue leaflet. actuator combination
TA-COMPACT-P is developed to work together with the EMO T The maximum recommended pressure drop over a valve and
actuator. Actuators of other brands require; actuator combination for close off (ΔpVclose) and to fulfill all stated
Working range: X (closed - fully open) = 11,6 - 15,8 performances (ΔpVmax).
Closing force: Min. 125 N (max. 500 N)
Ø22
DN EMO T * [kPa]
10
X 15
10
20 400
25
M30x1.5
32

*) Closing force 125 N.

IMI Hydronic Engineering will not be held responsible for the ΔpVclose = The maximum pressure drop that the valve can close against
control function if other brands of actuator are used. from an opened position, with a specified force (actuator) without
exceeding stated leakage rate.
ΔpVmax = The maximum allowed pressure drop over the valve, to fulfill all
stated performances.

3
IMI TA / Control valves / TA-COMPACT-P – NPT threads

Sizing
1. Choose the smallest valve size that can obtain the design 2. Check that the available ΔpV is within the working range
flow with some safety margin, see “qmax values”. The setting 15-400 kPa or 23-400 kPa.
should be as open as possible.

qmax values
Position
1 2 3 4 5 6 7 8 9 10
DN 10 21,5 39,5 54,0 68,5 80,0 91,0 99,0 107 113 120
DN 15 LF 44,0 71,0 97,0 123 148 170 190 210 227 245
DN 15 88,0 150 200 248 295 340 380 420 450 470
DN 20 210 335 460 575 680 780 890 990 1080 1150
DN 25 370 610 830 1050 1270 1490 1720 1870 2050 2150
DN 32 800 1220 1620 2060 2450 2790 3080 3350 3550 3700

qmax = l/h at each setting and fully open valve plug.

LF = Low flow

Installation
Application example Installation of actuator EMO T
TA-COMPACT-P TA-COMPACT-P
Approx. 15 mm of free space is required above the actuator.

TA-COMPACT-P TA-COMPACT-P
DN 10-20: 107 mm
DN 25-32: 113 mm

~15 mm

TA-COMPACT-P TA-COMPACT-P

TA-COMPACT-P + EMO T

IP54 IP54 IP54 IP54

Flow direction

4
Operating function
Setting Measuring ΔH

1. Turn the setting wheel to desired value, e.g. 5.0.

Shut-off

1. Remove any actuator.

2. Close the valve according to “Shut-off”.
3. Bypass the ∆p part by opening the bypass spindle ≈1 turn
anticlockwise, with a 5 mm Allen key.
1. Turn the setting wheel clockwise to X. 4. Connect TA’s balancing instrument to the measuring points
and measure.
Important! Close the bypass spindle after the measurement is
Measuring q completed.
1. Remove any actuator.
2. Connect TA’s balancing instrument to the measuring points.
3. Input the valve type, size and setting and the actual flow is
displayed.

5
IMI TA / Control valves / TA-COMPACT-P – NPT threads

Articles

L Male thread
ØB Threads according to ISO 228

DN D L H1 H2 B qmax Kg EAN Article No

H1
[l/h]
D 10 G1/2 74 55 55 54 120 0,53 7318794013308 52 164-010
15 LF G3/4 74 55 55 54 245 0,54 7318794025202 52 164-115
H2 15 G3/4 74 55 55 54 470 0,54 7318794013407 52 164-015
20 G1 85 64 55 64 1150 0,69 7318794013506 52 164-020
25 G1 1/4 93 64 61 64 2150 0,79 7318794013605 52 164-025
M30x1.5*
32 G1 1/2 112 78 61 78 3700 1,5 7318794013704 52 164-032

LF = Low flow
*) Connection to actuator.
→ = Flow direction

Connections

With female thread NPT

D D1 Threads according to ANSI/ASME B1.20.1-1983. Swivelling nut

L Valve DN D D1 L* EAN Article No

10 G1/2 3/8 NPT 21 7318794017801 52 163-210
15 G3/4 1/2 NPT 25 7318794017900 52 163-215
20 G1 1/2 NPT 18 7318794018303 52 163-320
20 G1 3/4 NPT 23 7318794018006 52 163-220
25 G1 1/4 3/4 NPT 27 7318794018402 52 163-325
25 G1 1/4 1 NPT 27 7318794018105 52 163-225
32 G1 1/2 1 NPT 27 7318794018501 52 163-332
32 G1 1/2 1 1/4 NPT 31 7318794018204 52 163-232

With male thread NPT

D D1 Threads according to ANSI/ASME B1.20.1-1983. Swivelling nut

L Valve DN D D1 L* EAN Article No

10 - - - - -
15 G3/4 1/2 NPT 29 4024052928415 2400-02.350
20 G1 3/4 NPT 32,5 4024052928514 2400-03.350
25 G1 1/4 1 NPT 35 4024052928613 2400-04.350
32 - - - - -

Soldering connection
D Ø According to ASME/ANSI B16.18 Swivelling nut

L Valve DN D Pipe Ø [in] ~ [mm] L* EAN Article No

10 G1/2 0.504 12.8 13 7318794022805 52 009-710
15 G3/4 0.629 16.0 16 7318794022904 52 009-715
20 G3/4 0.879 22 22 7318794023000 52 009-720
25 G1 1/4 1.130 29 26 7318794023109 52 009-725
32 G1 1/2 1.380 35 28 7318794023208 52 009-732

*) Fitting length (from the gasket surface to the end of the connection).

Other type of connections (ISO), see international version of TA-COMPACT-P.

6
Accessories

Grip for setting wheel, optional

For better grip when presetting.
For TA-COMPACT-P/-DP and TA-Modulator (DN 15-32).

Colour EAN Article No

Orange 7318794040502 52 164-950

Protection cap
For TA-COMPACT-P/-DP, TA-Modulator (DN 15-20), TBV-C/-CM.

EAN Article No
Red 7318793961105 52 143-100

Tamper proof cover

Set containing plastic cover and locking ring for valves with connection M30x1,5 to thermostatic head/
actuator.
Prevents manipulation of setting.

EAN Article No
7318794030206 52 164-100

Insulation
For heating/comfort cooling.
H1 Material: EPP.
Fire class: E (EN 13501-1), B2 (DIN 4102).

H2
Valve DN L H1 H2 D EAN Article No
10-15 100 61 71 84 7318794027404 52 164-901
ØD
L
20 118 67 79 90 7318794027503 52 164-902
25 127 71 84 104 7318794027602 52 164-903
32 154 85 99 124 7318794027701 52 164-904

Spindle extension
Recommended together with the insulation to minimize the risk of condensation at the valve-actuator
interface.
M30x1,5.

L EAN Article No
Plastic, black
30 4024052165018 2002-30.700

7
IMI TA / Control valves / TA-COMPACT-P – NPT threads

The products, texts, photographs, graphics and diagrams in this document may be subject to
alteration by IMI Hydronic Engineering without prior notice or reasons being given. For the most up
to date information about our products and specifications, please visit www.imi-hydronic.com.
5-5-46 TA-COMPACT-P – NPT threads ed.7 02.2019