DL411 TOP HAMMER

LONGHOLE DRILL
TECHNICAL SPECIFICATION

Sandvik DL411 is a fully-mechanized and compact KEY FEATURES

electro-hydraulic top hammer longhole drill designed Hydraulic rock drill HL1560ST (33 kW)
for underground mass mining in 3.6 x 3.6 m or larger Drilling module LFRC1600 (29 + 1 rods)
production drifts. It is capable of drilling vertical and Rod length 4’ - 6’ (1 220 - 1 830 mm)
inclined fans and single or parallel Ø64…115 mm Boom ZR30 (on front stabilizer)
longholes up to 54 meters in depth, using T38, T45 and Minimum drift size (H and W) 3 560 to 4 170 mm
T51 MF-rods or Ø65 mm/T45, ST58 and ST68 tube rods. Drift width in T-section 3.4 m (minimum)
The DL411 is mounted on a 4-wheel drive frame-steered Pivot point height 1 565 - 2 100 mm
and diesel-powered carrier. Sandvik DL411 is equipped Boom coverage (vertical holes) 3 000 mm
with the HL1560ST hydraulic rock drill, LFRC1600 drilling Transport height 3 200 mm
module, ZR30 telescopic boom, TAS drilling control Transport width 2 240 mm
system, remote control panel and FOPS operator’s Transport length 8 800 to 9 400 mm
(tramming) canopy for high drilling capacity and Transport weight 21 000 kg
maximum uptime. The 360° drilling module rotation and
wide boom swing and tilt angles make the unit suitable ROCK TOOLS AND HOLE LENGTH
for most mining methods and various service support Rod and hole diameter
applications. The CANbus based TAS drilling control *Hole
Rod Hole Rock drill
Thread length (m)
system with the user-friendly operating interface and Ø (mm) Ø (mm)
various instrumentation and automation levels allow T38 39 64 HL820ST
maximum productivity and good drilling accuracy. T45 46 76 HL820ST
The layout of the NC7N carrier is designed for good T45 65 (tube) 76 … 89 RD927L, HL820ST
37 … 54
visibility, mobility and stability, ensuring fast and safe T51 52 89 HL820ST
tramming in narrow mine drifts. The operating and ST58 76 (tube) 89 … 102 HL1560ST, RD927L
maintenance interface are designed for easy access, ST68 87 (tube) 102 … 115 HL1560ST
safe operation and all service points are accessible from *) Feed in contact with rock, front stinger retracted
the ground level.

1. DL411 TOP HAMMER - LONGHOLE DRILL

HYDRAULIC ROCK DRILL DRILLING CONTROL SYSTEM
Type of rock drill HL1560ST (TS2-319) Type of control system TAS
Percussion power 33 kW Operating principle CANbus
Percussion pressure Up to 200 bar Portable remote panel
Control panel
Percussion rate 30 - 40 Hz Cable length 20 m
Stabilizer Sleeve type Full percussion
Rotation speed 0 - 100 rpm (OMT500) Collaring
Rotation torque 2 330 Nm (OMT500) Adjustable parameters Rotation / Threading
Weight 490 kg Feed / Anti-jamming
Length with shank adapter 1 505 mm Flushing

Rotation pressure controlled feed With One-hole / Fan automation

DRILLING MODULE Diagnostics system Interactive
Type of drilling module LFRC1600 (TS2-342)
Rod length 1 220 - 1 830 mm (4’ - 6’ ) ELECTRIC SYSTEM
Storing capacity 29 + 1 rods (all threads) Standard voltages 380 - 690 V, 50 or 60 Hz
Retaining centralizer Pito 16 Total installed power 119 kW
Cuttings diverter CC1016 Main switch gear MSE 10
Set-off from stope face 1 000 mm IP-classification Specification TS2-132
Feed force 31 kN Allowed voltage fluctuation ± 10%
Feed and return speed 0.3 m/s Starting method Star delta 380 V - 690 V
Soft starter 575 V
DRILLING MODULE DIMENSIONS Automatic cable reel TCR3E
Type Rod length Total length Cable reel remote control At operator station and cable reel
LFRC1604 1 220 mm 3 360 mm Front and rear lights
10 x 50 W (24 V) LED
LFRC1605 1 525 mm 3 665 mm (combined working and driving)

LFRC1606 1 830 mm 3 970 mm Portable working lights 2 x 50 W (24 V) LED

Carrier positioning lights 2 x Laser type
LONGHOLE BOOM Rear parking / brake lights 2 x Red LED (24V)
Telescopic boom ZR30 (TS2-288) Stair case service lights LED (24V)
Boom swing Left 44° / Right 44° Sealed AGM batteries 2 x 12 V (145 Ah)
Boom (fan) tilt Back 30° / Forward 45°
Drilling module roll-over 360º AIR AND WATER SYSTEM
Boom extension 565 mm Flushing of holes By water

1 000 mm (4' rods) Water booster pump type WBP3

Drilling module travel 1 100 mm (5’ rods) Water pump capacity 215 l/min
1 400 mm (6’ rods) Water pump inlet pressure 2 -7 bar
Vertical hole drilling coverage 3 000 mm Flushing water pressure 10 - 20 bar
Pivot point height (boom vertical) 2 110 - 2 665 mm Shank lubrication device SLU1 (air / oil mist)
Front and rear stinger Mounted on feed cradle Air compressor CTN10 (1.0 m³/min at 7 bar)
1 500 mm (4’) Rock drill oil consumption 200 - 500 g/h
Rear stinger extension
1 700 mm (5’ and 6’) Rock drill air consumption 300 - 400 l/min
1 700 mm (4’) Air cleaner for external air supply IP5
Front stinger extension
2 000 mm (5’ and 6’)
OPERATOR’S SAFETY CANOPY
HYDRAULIC SYSTEM Canopy certification FOPS (ISO3449)
Type of hydraulic system TPC LH Unit height in tramming 3 200 mm
Operating principle Electric pilot control Canopy < 102 dB(A)
Sound pressure level EN 791
Powerpack HPP1590 (90 kW) Emitted 127 dB(A)
Filtration size (pressure / return) 20 µ / 10 µ Operator’s seat Ergonomic T-back seat
Oil tank volume 270 liters
Cooler for hydraulic oil OW45 oil-to-water (45 kW)
Low oil level indication Low oil level switch

2. DL411 TOP HAMMER - LONGHOLE DRILL

CARRIER OPTIONAL ITEMS
Type of carrier NC7N (frame-steered) Cleaning system
Carrier articulation ± 40º Low pressure system with reel Up to 15 bar (TS2-121)
Rear axle oscillation ± 10º High pressure system with reel Up to 220 bar (TS2-121)

Ground clearance 320 mm

Greasing systems
Diesel engine MB OM904LA (110kW, Tier 3) Automatic system Lincoln (for carrier, boom and rod
Exhaust catalyzer Standard handler)
Manual system Specification 5-2110
Transmission Hydrodynamic, Spicer T20 000
Axles Spicer
Electric system
Tires 12.00 - 20/20 RL *Voltage option 1 000 V (50 or 60 Hz) and DOL
Service brakes SAHR type, fail safe wet disc brakes starter
Dewatering pump outlet Site voltage 380 - 690 V (8 kW),
Parking / emergency brakes SAHR type, fail safe wet disc brakes
readiness excluding USA/CAN
Horizontal (0%): 15 km/h Flygt pump starter with plug Site voltage 1 000 V (8 kW),
Tramming speed
8°=1:7=14%: 5 km/h Electric cables Specification TS2-121
Ground fault and overcurrent unit VYK
Gradeability / sideways tilt 15° / 5°
Power outlet on carrier 110 or 230 V (16 A), site voltage
Front stabilizer 380 - 690 V
Carrier stabilization
2 x hydraulic jacks (rear) Amber flashing light LED (24 V)
Battery jump start CAT
Fuel tank 140 liters
Hand throttle Standard Air and water system
Filling pump for hydraulic oil Electric *Air compressor CT28 (2.8 m³/min, 18.5 kW)
or 2 x CT28 (5,6 m³/min, 37 kW)
Hand held fire extinguisher 7.7 or 9 kg (type ABC)
Air mist flushing kit For external air and water supply
Carrier centralized greasing Compressed air outlet Quick coupling for pneumatic
Specification 5-2110
points hand tools
1 x 60 liters air receiver For end-of-hole flushing (requires
Tramming alarm Standard
CT28)
Tramming cameras Front, rear and side Water hose reel and hose THR2.5E and Ø38 mm hose
Colour scheme Sandvik standard (length 65 m)
2 x Operator’s manual Fire suppression system
2 x Maintenance manual Spare fire extinguisher 7.7 or 9 kg (type ABC)
Documentation 2 x Technical manual (in English only) Automatic system Sandvik FS1000 (above 0°C)
2 x Parts manual (in English only) Manual or automatic system Ansul (6 nozzles)
1 x Toolman CD
Carrier
OPTIONAL ITEMS Reduced tramming speed 3rd gear lockout
Tramming cameras Front, side and rear
Drilling system
*Foam filled tires 4 pcs
*HL710S rock drill With 55 kW or 90kW powerpack
Fast filling and evacuation system Wiggins (complete)
*HL820ST rock drill With 90 kW powerpack
Wheel chocks and holders 2 Sets
*RD927L rock drill With 90 kW powerpack
Power extractor For HL1560ST, HL820ST, HL710S,
Extra items
RD927L
Spare rock drill HL1560ST, HL820ST, HL710S,
Drilling module wear parts kit For alternative tools
RD927L
Bit changer For LFRC1600 drilling module
Spare wheel assembly Standard or foam filled tires
Rear stinger extension 820 mm
Special tools for rock drill Field kit or complete set
Hydraulic system Documentation Extra manuals
*Oil cooler (Air actuated) OA30 (30 kW) Warranty extension One year (excl. Kazakhstan)
Vacuum pump For hydraulic oil Package: Country specific options USC, AUS and EUR
Package: Harsh water Basic or advance (TS2-049)
Package: Onboard air supply For air mist drilling
Instrumentation
Package: Onboard air and water For air mist drilling
Access detector, or protector Mandatory in Europe (TS2-211)
supply
Drilling instrument TMS for DL400 series (TS2-122)
Spirit level angle indicators 3 pcs (on boom and feed) *) replaces standard feature
OptiMine™ Remote Monitoring For data management

Automation
One-hole automation (incl. TMS) Specification TS2-198
Tele-remote drilling Including data transfer (USB/WLAN)
Fan automation (including TMS) Specification 5-9410
Data transfer USB / WLAN (excluding drill plan
software)

3. DL411 TOP HAMMER - LONGHOLE DRILL

MINIMUM PRODUCTION DRIFT SIZE* RC1600
1 030
H W WP HR
LFRC1604 mm 3 560 3 560 1 750 2 100
35°
LFRC1605 mm 3 865 3 865 2 050 2 100
2 240
LFRC1606 mm 4 170 4 170 2 350 2 100 1 995 3 000
* 100 mm clearance
35°
MAXIMUM PRODUCTION DRIFT SIZE** WP LF1600
2 000
H W WP HR 650
Front stinger
LFRC1604 mm 4 150 4 800 3 000 2 100
LFRC1605 mm 4 250 5 100 3 000 2 100

TS2-272:03/ENG/METRIC © Sandvik Mining and Rock Technology 2018 SANDVIK is a registered trademark owned by Sandvik Intellectual Property AB in Sweden and other countries.
LFRC1606 mm 4 370 5 400 3 000 2 100
** Rear stinger extended, front stinger retracted
H

HR

W
All dimensions in mm

SANDVIK

3 200 2 950 3 400

2 840 5 950
2 460
750 3 150
15° 17° 40°
750
195 1 425 320
3 280 3 175 2 575
Transport lenght
LF1604 LF1605 LF1606
Transport length mm 8 500 8 800 9 100 30°
1 945 45°
Total length (L) mm 3 360 3 665 3 970

SANDVIK
L
360°

2 100
195

1 425 15°
905 30° All dimensions in mm
3 040 3 175
10 055

Sandvik Mining and Rock Technology reserves the right to make changes to the information on this data sheet without prior notification to users.
Please contact a Sandvik representative for clarification on specifications and options.

ROCKTECHNOLOGY.SANDVIK

4. DL411 TOP HAMMER - LONGHOLE DRILL