Fosroc Renderoc S constructive solutions

Shrinkage compensated, polymer modified, fibre

reinforced, thixotropic repair mortar system

Uses Properties
Renderoc S is suitable for sprayed or trowelled applica- The following typical results were obtained at a water to
tions, with high build characteristics. Typical applications powder ratio of 0.14.
would include, but not be limited to, the following:
Test method Typical result
 All types of structural repair which can be applied by Compressive strength : > 20 N/mm² at 1 day
trowel or wet spray BS1881 : Pt 116 > 40 N/mm² at 3 days
> 50 N/mm² at 7 days
 Repair of structural members subjected to repetitive
> 60 N/mm² at 28 days
loading including application in trafficked areas
Flexural Strength : > 6 N/mm²
 Repairs to reinforced or pre-stressed beams or columns (BS 6319 pt 3)
Tensile Strength : > 4 N/mm²
 Repairs in industrial area, especially those containing
(BS 6319 pt 7)
mineral oils, lubricants etc

 Repairs in marine environments Instructions for use

Preparation
Advantages
It is essential that the substrate to be repaired is sound,
 Wet or dry spray application - rapid application of large
clean and free of all contamination.
quantities
The damaged areas of concrete to be removed must be
 Low rebound - when dry spray applied rebound is
clearly identified. The Perimeter of the area should be saw
minimal with subsequent saving in material cost
eping the sides square. Feather-edging is not permitted
 Extremely low permeability - gives excellent resistance and a minimum thickness of 10mm must be maintained
to attack by aggressive elements over the whole area.

The substrate should be prepared to provide a rough

Description
surface having at least a 5mm amplitude at 20mm
Renderoc S is supplied as a ready to use blend of dry pow- frequency.
ders, which requires only the addition of clean water to pro-
If unsound or oil contaminated concrete is found to
duce a highly consistent, repair mortar suitable for structural
extend beyond the premarked area, consult the engineer
concrete and masonry repairs.
in charge. Subject to approval cut back to clean sound
Renderoc S contains no metallic aggregate and is chloride concrete.
free.
If reinforcement is corroded ensure that the back of the
Renderoc S is formulated for sprayed or trowelled applica- steel has been exposed. reinforcement should have all
tions, in thicknesses upto 50mm in one layer by hand appli- rust removed by the use of power tools, abrasive basting
cation. Greater thicknesses can be achieved when spray (wet or dry) or wire brushing. Reinforcing steel should be
applied. exposed and cleaned around it’s whole circumference.
Steel should be prepared to Swedish Standard SIS
05-900:1967-SA2½ or BS4232 Ref. 24 second quality.

Extra protection to the reiforcement can be provided by

Nitoprime Zincrich*† and Galvashied XP*† or Galvashield
CC*†. Dependent on the circumstances of use and
requirement of the client.

Severely corroded reinforcement may require replacement

and the engineer must be consulted.
Renderoc S
Fosroc Renderoc S

Water Saturation Estimating

Thoroughly saturate the surface of the concrete to provide a Supply
saturated surface dry condition. Poor quality concrete may Renderoc S : 25kg bags
require soaking for a significant length of time. Any surface
Yield
water should be removed using an oil free compressed airjet.
Renderoc S : approx. 13 litres per 25kg bag
Mixing
Limitations
Renderoc S should be mixed mechanically with a Heavy
Duty, slow speed drill or a forced action mixer fitted with  Renderoc S should not be used when the ambient
Fosroc MR3 mortar mixing paddle. temperature is below 5ºC and falling.

Add 3.5 litres of water per 25kg bag. Pour the desired  Renderoc S should not be exposed to running water
quantity of water into a suitably sized mixing vessel for full either during application or prior to final set.
bag mixing. Do not use part-bags. Place 3.5 litres of cool,
clean drinking water in the mixing container followed by the Storage
full bag of Renderoc S and mix for 3-5 minutes, until the mix
Shelf life
becomes fully homogeneous.
Renderoc S has a shelf life of 12 months; if kept in a dry
Application
environment, in its original, unopened packing. If stored in
After mixing, Renderoc S can be sprayed or trowel applied. conditions of high humidity and/or temperature, the shelf life
Suitable spraying units are Putzmeister P11, Turbosol T20 will be reduced.
or Meyco Deguna 20. When applying by hand, Renderoc S,
must be forced tightly into the substrate to ensure intimate Precautions
contact with the pre-wetted substrate. Levelling and initial
Health and safety
finishing should be carried using a wooden or plastic float.
Final finishing should be carried out using a steel float. When Renderoc S contains cement powders which, when mixed
the material has stiffened to the point where finger pressure with water or upon becoming damp, release alkalis which
lightly marks the surface, a final firm trowelling should be can be harmful to the skin. In case of contact with eyes, rinse
given using a steel float. immediately with plenty of clean water and seek medical
advice. If swallowed seek medical attention immediately - do
Curing
not induce vomiting.
Renderoc S demands good curing. Particular care is re-
Fire
quired in hot/windy conditions. Curing is to be commenced
immediately either by applying Concure 1315, or by covering Renderoc S, is non-flammable and thus presents no fire
the work with plastic sheet fixed over wet hessian and taped hazard.
at all edges.
For further information, please refer to the Product Material
Nitobond AR can be used as a curing compound but not Safety Data Sheet for Renderoc S.
recommended in situations where overcoating with epoxy
coatings is required. However it is suitable when overcoated
with the Dekguard range of protective coatings.
†
See separate data sheet

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.

Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
Al Gurg Fosroc Co. LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
United Arab Emirates Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
www.fosroc.com Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com

UAE/0734/11/B
Revision date: 12/09/2019 Revision: 9 Supersedes date: 09/06/2016

SAFETY DATA SHEET

RENDEROC S

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1. Product identifier

Product name RENDEROC S

Product number 2232002AE1

1.2. Relevant identified uses of the substance or mixture and uses advised against
Identified uses Cementitious Repair Mortar.

1.3. Details of the supplier of the safety data sheet

Supplier Al Gurg Fosroc LLC
PO Box 657
Dubai
United Arab Emirates
+ 971 4 2858606

1.4. Emergency telephone number

Emergency telephone +97142039699 (08:00 to 16:30) // +971506258232 (16:30 to 08:00)GMT+4

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture

Classification (EC 1272/2008)
Physical hazards Not Classified

Health hazards Skin Irrit. 2 - H315 Eye Dam. 1 - H318 Skin Sens. 1 - H317 STOT SE 3 - H335

Environmental hazards Not Classified

Human health Dust or splashes from the mixture may cause permanent eye damage. Dust may irritate the
respiratory system. Symptoms following overexposure may include the following: Coughing.
Dust has an irritating effect on moist skin. Prolonged contact with moist or wet product may
cause burns. Frequent inhalation of dust over a long period of time increases the risk of
developing lung diseases.

Environmental The product will harden into a solid mass in contact with water and moisture. The resultant
material is not biodegradable.

2.2. Label elements

Hazard pictograms

Signal word Danger

1/9
Revision date: 12/09/2019 Revision: 9 Supersedes date: 09/06/2016

RENDEROC S

Hazard statements H315 Causes skin irritation.

H318 Causes serious eye damage.
H317 May cause an allergic skin reaction.
H335 May cause respiratory irritation.

Precautionary statements P271 Use only outdoors or in a well-ventilated area.

P280 Wear protective gloves/ protective clothing/ eye protection/ face protection.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P501 Dispose of contents/ container in accordance with national regulations.

Supplementary precautionary P261 Avoid breathing vapour/ spray.

statements P264 Wash contaminated skin thoroughly after handling.
P272 Contaminated work clothing should not be allowed out of the workplace.
P302+P352 IF ON SKIN: Wash with plenty of water.
P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P310 Immediately call a POISON CENTER/ doctor.
P312 Call a POISON CENTRE/doctor if you feel unwell.
P321 Specific treatment (see medical advice on this label).
P332+P313 If skin irritation occurs: Get medical advice/ attention.
P333+P313 If skin irritation or rash occurs: Get medical advice/ attention.
P362+P364 Take off contaminated clothing and wash it before reuse.
P403+P233 Store in a well-ventilated place. Keep container tightly closed.
P405 Store locked up.

2.3. Other hazards

This product does not contain any substances classified as PBT or vPvB.

SECTION 3: Composition/information on ingredients

3.2. Mixtures

ORDINARY PORTLAND CEMENT 30-60%

CAS number: 65997-15-1 EC number: 266-043-4

Classification
Skin Irrit. 2 - H315
Eye Dam. 1 - H318
Skin Sens. 1 - H317
STOT SE 3 - H335

CSA EXPANSIVE AGENT 1-5%

CAS number: 1305-78-8

Classification
Skin Irrit. 2 - H315
Eye Irrit. 2 - H319
STOT SE 3 - H335

2/9
Revision date: 12/09/2019 Revision: 9 Supersedes date: 09/06/2016

RENDEROC S

SILICA SAND <1%

CAS number: 14808-60-7

Classification
Eye Irrit. 2 - H319
STOT SE 3 - H335

The Full Text for all R-Phrases and Hazard Statements are Displayed in Section 16.

SECTION 4: First aid measures

4.1. Description of first aid measures

General information No personal protective equipment is needed for first aid responders. First aid workers should
avoid contact with wet cement or wet cement containing preparations.

Inhalation Move affected person to fresh air at once. Dust in throat and nasal passages should clear
spontaneously. Get medical attention if irritation persists or later develops, or if discomfort,
coughing or other symptoms persist.

Ingestion Do not induce vomiting. Rinse mouth thoroughly with water. Give plenty of water to drink. Give
milk instead of water if readily available. Never give anything by mouth to an unconscious
person. Get medical attention immediately.

Skin contact Wash immediately with copious quantities of water. Remove contaminated clothing
immediately. Obtain medical advice if skin orders develop.

Eye contact Do not rub eye. Remove any contact lenses and open eyelids wide apart. Rinse immediately
with plenty of water. Continue to rinse for 30 minutes. Get medical attention. Show this Safety
Data Sheet to the medical personnel.

4.2. Most important symptoms and effects, both acute and delayed
General information The severity of the symptoms described will vary dependent on the concentration and the
length of exposure.

Inhalation Frequent inhalation of dust over a long period of time increases the risk of developing lung
diseases.

Ingestion Ingestion of large doses may result in irritation to the gastrointestinal tract.

Skin contact May have an irritating effect on moist skin after prolonged contact, or may cause dermatitis
after repeated contact.Prolonged skin contact with wet preparation may cause serious burns
without pain being felt, including through clothing.

Eye contact Eye contact may cause serious and potentially irreversible injuries.

4.3. Indication of any immediate medical attention and special treatment needed
Notes for the doctor No specific recommendations.

SECTION 5: Firefighting measures

5.1. Extinguishing media

Suitable extinguishing media The product is not flammable. Use fire-extinguishing media suitable for the surrounding fire.

5.2. Special hazards arising from the substance or mixture

Specific hazards Water used for fire extinguishing, which has been in contact with the product, may be
corrosive. No unusual fire or explosion hazards noted.

Hazardous combustion No known hazardous decomposition products.

products

3/9
Revision date: 12/09/2019 Revision: 9 Supersedes date: 09/06/2016

RENDEROC S

5.3. Advice for firefighters

Protective actions during No specific firefighting precautions known.
firefighting

Special protective equipment Use protective equipment appropriate for surrounding materials.
for firefighters

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Personal precautions Avoid inhalation of dust. Use work methods which minimize dust production. Avoid contact
with eyes and prolonged skin contact. Wear protective clothing as described in Section 8 of
this safety data sheet.

6.2. Environmental precautions

Environmental precautions Collect and dispose of spillage as indicated in Section 13. Do not discharge into drains or
watercourses or onto the ground.

6.3. Methods and material for containment and cleaning up

Methods for cleaning up Collect powder using special dust vacuum cleaner with particle filter or carefully sweep into
suitable waste disposal containers and seal securely. Dry material: Collect powder using
special dust vacuum cleaner with particle filter. Alternatively, damp powder with fine spray (to
avoid dust formation) and remove slurry. Place into container and allow to solidify before
disposal as described in section 13. Wet material: Clean up wet material and place in a
container. Allow to dry and solidify before disposal as described in section 13.

6.4. Reference to other sections

Reference to other sections For personal protection, see Section 8. For waste disposal, see section 13.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

Usage precautions Avoid contact with skin and eyes. Avoid generation and spreading of dust. Avoid inhalation of
dust. Mechanical ventilation or local exhaust ventilation may be required. Change
contaminated clothing. Do not eat, drink or smoke when using the product.

7.2. Conditions for safe storage, including any incompatibilities

Storage precautions Store in tightly-closed, original container in a dry and cool place. Unsuitable container
materials: Aluminium. The product contains less than 2 mg chromate/kg dry cement, and this
limit will not be exceeded for 6 months from the packing date stated on the packaging. Seal
opened containers and use up as soon as possible. To be stored out of reach of children in its
original packaging in a dry place.

7.3. Specific end use(s)

Specific end use(s) The identified uses for this product are detailed in Section 1.2.

SECTION 8: Exposure controls/Personal protection

8.1. Control parameters

Occupational exposure limits
ORDINARY PORTLAND CEMENT
Long-term exposure limit (8-hour TWA): WEL 10 mg/m³ inhalable dust
Long-term exposure limit (8-hour TWA): WEL 4 mg/m³ respirable dust
CSA EXPANSIVE AGENT
Long-term exposure limit (8-hour TWA): OES 10 mg/m3 Inhal. Dust 4 mg/m3 Resp. Dust

4/9
Revision date: 12/09/2019 Revision: 9 Supersedes date: 09/06/2016

RENDEROC S

SILICA SAND
Long-term exposure limit (8-hour TWA): WEL 0,1 mg/m³
WEL = Workplace Exposure Limit

ORDINARY PORTLAND CEMENT (CAS: 65997-15-1)

DNEL Workers - Inhalation; Short term : 3 mg/m³

2,2-DIMETHYL 1,3-PROPANEDIOL (CAS: 126-30-7)

DNEL Workers - Inhalation; Long term systemic effects: 35 mg/m³

Workers - Dermal; Long term systemic effects: 10 mg/kg bw/day
General population - Inhalation; Long term systemic effects: 8.7 mg/m³
General population - Dermal; Long term systemic effects: 5 mg/kg bw/day
General population - Oral; Long term systemic effects: 5 mg/kg bw/day

PNEC - Fresh water; 5 mg/l

- marine water; 0.5 mg/l
- STP; 20 mg/l

8.2. Exposure controls

Protective equipment

Appropriate engineering Atmospheric levels of dust must be maintained within the Occupational Exposure Limit.
controls Where mechanical methods are inadequate or impractical, appropriate personal protective
equipment must be used.

Personal protection Personal protection equipment should be chosen according to the CEN standards and in
discussion with the supplier of the personal protective equipment. This product may present a
chromate (VI) allergy risk. Users should wear appropriate personal protective equipment.

Eye/face protection The following protection should be worn: Chemical splash goggles. (conform EN 166)

Hand protection Use impervious, abrasion and alkali resistant gloves. Barrier cream applied before work may
make it easier to clean the skin after exposure, but does not prevent absorption through the
skin.

Other skin and body Use barrier creams to minimise skin contact. Wear appropriate clothing to prevent repeated or
protection prolonged skin contact.

Hygiene measures This product contains silica sands.

The grain size distribution of silica sand present means that it is not classified as hazardous.
However, any respirable crystalline dust generated by secondary processing may cause
health effects.
Prolonged and /or massive inhalation of respirable crystalline silica dust may cause lung
fibrosis, commonly referred to as silicosis. Principal symptoms of silicosis are cough and
breathlessness.
Occupational exposure to respirable crystalline silica dust should be monitored and controlled.

Respiratory protection Wear a respirator fitted with the following cartridge: Particulate filter, type P2.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties

Appearance Dusty powder.

5/9
Revision date: 12/09/2019 Revision: 9 Supersedes date: 09/06/2016

RENDEROC S

Colour Grey.

Odour Odourless.

Odour threshold Not relevant.

pH pH (concentrated solution): >12

Melting point >1250°C

Initial boiling point and range Not applicable.

Flash point Not applicable.

Evaporation rate Not applicable.

Evaporation factor Not applicable.

Flammability (solid, gas) Not applicable.

Upper/lower flammability or The product is not flammable.

explosive limits

Other flammability Not applicable.

Vapour pressure Not applicable.

Vapour density Not applicable.

Relative density Not determined.

Bulk density Not determined.

Solubility(ies) Slightly soluble in water. Hardens in contact with water.

Partition coefficient Not available.

Auto-ignition temperature Not determined.

Decomposition Temperature Not determined.

Viscosity Not applicable.

Explosive properties Not considered to be explosive.

Explosive under the influence Not considered to be explosive.

of a flame

Oxidising properties The mixture itself has not been tested but none of the ingredient substances meet the criteria
for classification as oxidising.

Comments Information given is applicable to the product as supplied.

9.2. Other information

Other information Not available.

SECTION 10: Stability and reactivity

10.1. Reactivity
Reactivity When mixed with water, hardens to form a stable mass that is not reactive in normal
conditions.

10.2. Chemical stability

6/9
Revision date: 12/09/2019 Revision: 9 Supersedes date: 09/06/2016

RENDEROC S

Stability When stored under humid conditions, the chromate neutralization will decrease. Stable under
the prescribed storage conditions. This product has a shelf life. If not stored in accordance
with packaging instructions (sealed and dry) There is a risk of the presence of hexavalent
chromate leading to a risk of an allergic reaction

10.3. Possibility of hazardous reactions

Possibility of hazardous Not known. Will not polymerise.
reactions

10.4. Conditions to avoid

Conditions to avoid Water, moisture.

10.5. Incompatible materials

Materials to avoid Acids. Chemically-active metals.

10.6. Hazardous decomposition products

Hazardous decomposition No known hazardous decomposition products.
products

SECTION 11: Toxicological information

11.1. Information on toxicological effects

Skin sensitisation
Skin sensitisation Some individuals may exhibit eczema upon exposure to wet cement caused either by the high
pH which induces irritant contact dermatitis, or by an immunological reaction to soluble Cr (VI)
which elicits allergic contact dermatitis.

Inhalation Irritating to respiratory system. Inflammation of the nasal mucous membrane by exposure to
cement dust.

Ingestion May cause irritation of mouth, throat and digestive tract.

Skin contact This product is strongly irritating. Prolonged contact may cause burns. May cause
sensitisation by skin contact.

Eye contact Irritating and may injure eye tissue if not removed promptly.

Acute and chronic health Repeated and/or prolonged contact may lead to dermatitis.
hazards

Toxicological information on ingredients.

ORDINARY PORTLAND CEMENT

Acute toxicity - dermal

Acute toxicity dermal (LD₅₀ 2,000.0

mg/kg)

Species Rabbit

SECTION 12: Ecological information

Ecotoxicity The product is not expected to be hazardous to the environment.

12.1. Toxicity
Toxicity Not considered toxic to fish.

Acute aquatic toxicity

7/9
Revision date: 12/09/2019 Revision: 9 Supersedes date: 09/06/2016

RENDEROC S

Acute toxicity - fish Not determined.

The product is not expected to be hazardous to the environment. The addition of cements to
water will, however, cause the pH to rise and may therefore be toxic to aquatic life in some
circumstances.

Ecological information on ingredients.

ORDINARY PORTLAND CEMENT

Acute aquatic toxicity

Acute toxicity - fish Not determined.

12.2. Persistence and degradability

Persistence and degradability The product is not biodegradable.

12.3. Bioaccumulative potential

Bioaccumulative potential The product is not bioaccumulating.

Partition coefficient Not available.

12.4. Mobility in soil

Mobility The product hardens to a solid, immobile substance. The product is not volatile but may be
spread by dust-raising handling.

12.5. Results of PBT and vPvB assessment

Results of PBT and vPvB This substance is not classified as PBT or vPvB according to current EU criteria.
assessment

12.6. Other adverse effects

Other adverse effects None known.

SECTION 13: Disposal considerations

13.1. Waste treatment methods

General information Do not empty into drains, sewers or water courses. Cement that has exceeded its shelf life:
when demonstrated that it contains more than 0.0002% Cr (VI), the product shall not be used
other than in controlled closed and totally automated processes. It may be recycled and/or
treated again with a reducing agent.

Disposal methods Dispose of waste to licensed waste disposal site in accordance with the requirements of the
local Waste Disposal Authority. Note that fully cured material is not considered as hazardous
waste.

SECTION 14: Transport information

General The product is not covered by international regulations on the transport of dangerous goods
(IMDG, IATA, ADR/RID).

14.1. UN number
Not applicable.

14.2. UN proper shipping name

Not applicable.

14.3. Transport hazard class(es)

No transport warning sign required.

14.4. Packing group

8/9
Revision date: 12/09/2019 Revision: 9 Supersedes date: 09/06/2016

RENDEROC S

Not applicable.

14.5. Environmental hazards

Environmentally hazardous substance/marine pollutant

No.

14.6. Special precautions for user

Not applicable.

14.7. Transport in bulk according to Annex II of MARPOL and the IBC Code
Transport in bulk according to Not applicable.
Annex II of MARPOL 73/78
and the IBC Code

SECTION 15: Regulatory information

15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
National regulations The Control of Substances Hazardous to Health Regulations 2002 (SI 2002 No. 2677) (as
amended).
The Chemicals (Hazard Information and Packaging for Supply) Regulations 2009 (SI 2009
No. 716).

EU legislation Dangerous Substances Directive 67/548/EEC.

Dangerous Preparations Directive 1999/45/EC.
Regulation (EC) No 1272/2008 of the European Parliament and of the Council of 16
December 2008 on classification, labelling and packaging of substances and mixtures (as
amended).

Guidance Workplace Exposure Limits EH40.

15.2. Chemical safety assessment

No chemical safety assessment has been carried out.

SECTION 16: Other information

General information Only trained personnel should use this material.

Revision comments NOTE: Lines within the margin indicate significant changes from the previous revision.

Revision date 12/09/2019

Revision 9

Supersedes date 09/06/2016

SDS number 23910

Hazard statements in full H315 Causes skin irritation.

H317 May cause an allergic skin reaction.
H318 Causes serious eye damage.
H319 Causes serious eye irritation.
H335 May cause respiratory irritation.

The information on this data sheet represents our current data and is reliable provided that the product is used under the
prescribed conditions and in accordance with the application specified on the packaging and/or in the technical guidance
literature. Any other use of the product which involves using the product in combination with any other product or any other
process is the responsibility of the user.

9/9