THGBMHG7C1LBAIL

TOSHIBA e-MMC Module

16GB THGBMHG7C1LBAIL
INTRODUCTION
THGBMHG7C1LBAIL is 16GB density of e-MMC Module product housed in 153 ball BGA package. This unit is utilized
advanced TOSHIBA NAND flash device(s) and controller chip assembled as Multi Chip Module. THGBMHG7C1LBAIL
has an industry standard MMC protocol for easy use.

FEATURES
THGBMHG7C1LBAIL Interface
THGBMHG7C1LBAIL has the JEDEC/MMCA Version 5.1 interface with 1-I/O, 4-I/O and 8-I/O mode.

Pin Connection
P-WFBGA153-1113-0.50 (11.5mm x 13mm, H0.8mm max. package)

14 NC NC NC NC NC NC NC NC NC NC NC NC NC NC

13 NC NC NC NC NC NC NC NC NC NC NC NC NC NC

12 NC NC NC NC NC NC NC NC NC NC NC NC NC NC

11 NC NC NC NC NC NC

10 NC NC NC VSF VSF RFU Vss Vcc RFU NC NC RFU

9 NC NC NC VSF Vcc NC NC NC

8 NC NC NC RFU Vss NC NC NC
Top View
7 RFU NC NC Vss RFU NC NC RFU

6 Vss DAT7 VccQ Vcc RFU CLK NC VssQ

5 DAT2 DAT6 NC RFU Vcc Vss DS Vss RST_n CMD VssQ VccQ

4 DAT1 DAT5 VssQ NC index VccQ VccQ VssQ

3 DAT0 DAT4 NC NC NC NC RFU NC NC NC NC NC NC VccQ

2 NC DAT3 VDDi NC NC NC NC NC NC NC NC NC VssQ NC

1 NC NC NC NC NC NC NC NC NC NC NC NC NC NC

A B C D E F G H J K L M N P

Pin Number Name Pin Number Name Pin Number Name Pin Number Name

A3 DAT0 C2 VDDi J5 Vss N4 VccQ

A4 DAT1 C4 VssQ J10 Vcc N5 VssQ
A5 DAT2 C6 VccQ K5 RST_n P3 VccQ
A6 Vss E6 Vcc K8 Vss P4 VssQ
B2 DAT3 E7 Vss K9 Vcc P5 VccQ
B3 DAT4 F5 Vcc M4 VccQ P6 VssQ
B4 DAT5 G5 Vss M5 CMD
B5 DAT6 H5 DS M6 CLK
B6 DAT7 H10 Vss N2 VssQ
NC: No Connect, shall be connected to ground or left floating.
RFU: Reserved for Future Use, shall be left floating for future use.
VSF: Vendor Specific Function, shall be left floating.

1 Sep. 17th, 2015

 THGBMHG7C1LBAIL

Part Numbers
Available e-MMC Module Products – Part Numbers

TOSHIBA Part Number Density Package Size NAND Flash Type Weight

THGBMHG7C1LBAIL 16GB 11.5mm x 13mm x 0.8mm(max) 1 x 128Gbit 15nm 0.18g typ.

Operating Temperature and Humidity Conditions

-25°C to +85°C, and 0%RH to 95%RH non-condensing

Storage Temperature and Humidity Conditions

-40°C to +85°C, and 0%RH to 95%RH non-condensing

Performance
X8 mode/ Sequential access
Typ. Performance
Interleave Frequency [MB/sec]
TOSHIBA Part Number Density NAND Flash Type VccQ
Operation /Mode
Read Write

1.8V 45 45
52MHz/SDR
3.3V 45 45
Non 1.8V 90 45
THGBMHG7C1LBAIL 16GB 1 x 128Gbit 15nm 52MHz/DDR
Interleave 3.3V 90 45
HS200 1.8V 180 45
HS400 1.8V 220 45

Power Supply
Vcc = 2.7V to 3.6V
VccQ = 1.7V to 1.95V / 2.7V to 3.6V

Operating Current (RMS)

The measurement for max RMS current is done as average RMS current consumption over a period of 100ms

Max Operating
TOSHIBA Part Interleave Frequency Current [mA]
Density NAND Flash Type VccQ
Number Operation /Mode
Iccq Icc

1.8V 95 40
52MHz/SDR
3.3V 110 40
Non 1.8V 115 45
THGBMHG7C1LBAIL 16GB 1 x 128Gb 15nm 52MHz/DDR
Interleave 3.3V 140 45
HS200 1.8V 170 55
HS400 1.8V 215 55

2 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Sleep Mode Current

Iccqs [μA] Iccqs+Iccs [μA]

Interleave
TOSHIBA Part Number Density NAND Flash Type
Operation
Typ. *1 Max. *2 Typ. *1 Max. *2

Non
THGBMHG7C1LBAIL 16GB 1 x 128Gbit 15nm 100 510 120 585
Interleave
*1 : The conditions of typical values are 25°C and VccQ = 3.3V or 1.8V.
*2 : The conditions of maximum values are 85°C and VccQ = 3.6V or 1.95V.

3 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Product Architecture

The diagram in Figure 1 illustrates the main functional blocks of the THGBMHG7C1LBAIL.
Specification of the CREG and recommended values of the CVCC, and CVCCQ in the Figure 1 are as follows.

Parameter Symbol Unit Min. Typ. Max. Remark

μF 0.10 - 2.2* Except HS400

VDDi capacitor value CREG
μF 1.00 - 2.2* HS400

VCC capacitor value CVCC μF - 2.2 + 0.1 -

VCCQ capacitor value CVCCQ μF - 2.2 + 0.1 -

* Toshiba recommends that the value should be usually applied as the value of C REG.

Package
Vcc(3.3V)
CVCC
VccQ(1.8V/3.3V)
CVCCQ NAND
REGULATOR Control signal

NAND I/O BLOCK

MMC I/O BLOCK

VDDi

I/O BLOCK
CREG
CORE LOGIC NAND
x11 NAND I/O
MMC I/F(1.8V/3.3V)

Figure 1 THGBMHG7C1LBAIL Block Diagram

4 Sep. 17th, 2015

 THGBMHG7C1LBAIL
PRODUCT SPECIFICATIONS
Package Dimensions
P-WFBGA153-1113-0.50 (11.5mm x 13mm, H0.8mm max. package) Unit: mm

5 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Density Specifications
Interleave User Area Density SEC_COUNT in
Density Part Number
Operation [Bytes] Extended CSD
16GB THGBMHG7C1LBAIL Non Interleave 15,758,000,128 0x01D5A000
1) User area density shall be reduced if enhanced user data area is defined.

Register Informations
OCR Register

OCR bit VDD Voltage window Value

[6:0] Reserved 000 0000b

[7] 1.70-1.95 1b
[14:8] 2.0-2.6 000 0000b
[23:15] 2.7-3.6 1 1111 1111b
[28:24] Reserved 0 0000b
[30:29] Access Mode 10b
[31] ( card power up status bit (busy) )1
1) This bit is set to LOW if the Device has not finished the power up routine.

CID Register

CID-slice Name Field Width Value

[127:120] Manufacturer ID MID 8 0001 0001b

[119:114] Reserved - 6 0b
[113:112] Device/BGA CBX 2 01b
[111:104] OEM/Application ID OID 8 0b
[103:56] Product name PNM 48 0x30 31 36 47 33 30 (016G30)
[55:48] Product revision PRV 8 0x00
[47:16] Product serial PSN 32 Serial number
[15:8] Manufacturing date MDT 8 see-JEDEC Specification
[7:1] CRC7 checksum CRC 7 CRC7
[0] Not used, always ‘1’ - 1 1b

6 Sep. 17th, 2015

 THGBMHG7C1LBAIL
CSD Register

CSD-slice Name Field Width Cell Type Value

[127:126] CSD structure CSD_STRUCTURE 2 R 0x3

[125:122] System specification version SPEC_VERS 4 R 0x4
[121:120] Reserved - 2 R 0x0
[119:112] Data read access-time 1 TAAC 8 R 0x27
Data read access-time 2 in CLK cycles
[111:104] NSAC 8 R 0x00
(NSAC * 100)
[103:96] Max. bus clock frequency TRAN_SPEED 8 R 0x32
[95:84] Device command classes CCC 12 R 0x8F5
[83:80] Max. read data block length READ_BL_LEN 4 R 0x9
[79:79] Partial blocks for read allowed READ_BL_PARTIAL 1 R 0x0
[78:78] Write block misalignment WRITE_BLK_MISALIGN 1 R 0x0
[77:77] Read block misalignment READ_BLK_MISALIGN 1 R 0x0
[76:76] DSR implemented DSR_IMP 1 R 0x0
[75:74] Reserved - 2 R 0x0
[73:62] Device size C_SIZE 12 R 0xFFF
[61:59] Max. read current @ VDD min. VDD_R_CURR_MIN 3 R 0x7
[58:56] Max. read current @ VDD max. VDD_R_CURR_MAX 3 R 0x7
[55:53] Max. write current @ VDD min. VDD_W_CURR_MIN 3 R 0x7
[52:50] Max. write current @ VDD max. VDD_W_CURR_MAX 3 R 0x7
[49:47] Device size multiplier C_SIZE_MULT 3 R 0x7
[46:42] Erase group size ERASE_GRP_SIZE 5 R 0x1F
[41:37] Erase group size multiplier ERASE_GRP_MULT 5 R 0x1F
[36:32] Write protect group size WP_GRP_SIZE 5 R 0x07
[31:31] Write protect group enable WP_GRP_ENABLE 1 R 0x1
[30:29] Manufacturer default ECC DEFAULT_ECC 2 R 0x0
[28:26] Write speed factor R2W_FACTOR 3 R 0x1
[25:22] Max. write data block length WRITE_BL_LEN 4 R 0x9
[21:21] Partial blocks for write allowed WRITE_BL_PARTIAL 1 R 0x0
[20:17] Reserved - 4 R 0x0
[16:16] Content protection application CONTENT_PROT_APP 1 R 0x0
[15:15] File format group FILE_FORMAT_GRP 1 R/W 0x0
[14:14] Copy flag (OTP) COPY 1 R/W 0x0
[13:13] Permanent write protection PERM_WRITE_PROTECT 1 R/W 0x0
[12:12] Temporary write protection TMP_WRITE_PROTECT 1 R/W/E 0x0
[11:10] File format FILE_FORMAT 2 R/W 0x0
[9:8] ECC code ECC 2 R/W/E 0x0
[7:1] CRC CRC 7 R/W/E CRC
[0] Not used, always ‘1’ - 1 - 0x1

7 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Extended CSD Register

Size Cell
CSD-slice Name Field Value
(Bytes) Type

[511:506] Reserved - 6 - All ‘0’

[505] Extended Security Commands Error EXT_SECURITY_ERR 1 R 0x00
[504] Supported Command Sets S_CMD_SET 1 R 0x01
[503] HPI features HPI_FEATURES 1 R 0x01
[502] Background operations support BKOPS_SUPPORT 1 R 0x01
[501] Max_packed read commands MAX_PACKED_READS 1 R 0x3F
[500] Max_packed write commands MAX_PACKED_WRITES 1 R 0x3F
[499] Data Tag Support DATA_TAG_SUPPORT 1 R 0x01
[498] Tag Unit Size TAG_UNIT_SIZE 1 R 0x03
[497] Tag Resource Size TAG_RES_SIZE 1 R 0x00
[496] Context management capabilities CONTEXT_CAPABILITIES 1 R 0x7F
[495] Large Unit size LARGE_UNIT_SIZE_M1 1 R 0x00
[494] Extended partitions attribute support EXT_SUPPORT 1 R 0x03
[493] Supported modes SUPPORTED_MODES 1 R 0x01
[492] FFU features FFU_FEATURES 1 R 0x00
[491] Operation codes timeout OPERATION_CODES_TIMEOUT 1 R 0x00
[490:487] FFU Argument FFU_ARG 4 R 0xFFFFFFFF
[486] Barrier support BARRIER_SUPPORT 1 R 0x01
[485:309] Reserved - 177 - All ‘0’
[308] CMD Queuing Support CMDQ_SUPPORT 1 R 0x01
[307] CMD Queuing Depth CMDQ_DEPTH 1 R 0x1F
[306] Reserved - 1 - 0x00
NUMBER_OF_FW_SECTORS_C
[305:302] Number of FW sectors correctly programmed 4 R All ’0’
ORRECTLY_PROGRAMMED
VENDOR_PROPRIETARY
[301:270] Vendor proprietary health report 32 R All ‘0’
_HEALTH_REPORT
[269] Device life time estimation type B DEVICE_LIFE_TIME_EST_TYP_B 1 R 0x00
[268] Device life time estimation type A DEVICE_LIFE_TIME_EST_TYP_A 1 R 0x01
[267] Pre EOL information PRE_EOL_INFO 1 R 0x01
[266] Optimal read size OPTIMAL_READ_SIZE 1 R 0x08
[265] Optimal write size OPTIMAL_WRITE_SIZE 1 R 0x08
[264] Optimal trim unit size OPTIMAL_TRIM_UNIT_SIZE 1 R 0x01
[263:262] Device version DEVICE_VERSION 2 R 0x01
[261:254] Firmware version FIRMWARE_VERSION 8 R 0x03

[253] Power class for 200MHz, DDR at VCC=3.6V PWR_CL_DDR_200_360 1 R 0xCC

[252:249] Cache size CACHE_SIZE 4 R 0x00001000

[248] Generic CMD6 timeout GENERIC_CMD6_TIME 1 R 0x0A
[247] Power off notification(long) timeout POWER_OFF_LONG_TIME 1 R 0x32
[246] Background operations status BKOPS_STATUS 1 R 0x00
CORRECTLY
[245:242] Number of correctly programmed sectors 4 R 0x00000000
_PRG_SECTORS_NUM
[241] 1st initialization time after partitioning INI_TIMEOUT_AP 1 R 0x1E

8 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Size Cell
CSD-slice Name Field Value
(Bytes) Type

[240] Cache Flushing Policy CACHE_FLUSH_POLICY 1 R 0x01

[239] Power class for 52MHz, DDR @ 3.6V PWR_CL_DDR_52_360 1 R 0x66
[238] Power class for 52MHz, DDR @ 1.95V PWR_CL_DDR_52_195 1 R 0xBB
Power class for 200MHz,
[237] PWR_CL_200_195 1 R 0xBB
@ VCCQ =1.95V, VCC = 3.6V

Power class for 200MHz,

[236] PWR_CL_200_130 1 R 0xBB
@ VCCQ=1.3V, VCC = 3.6V

Minimum Write Performance for 8bit

[235] MIN_PERF_DDR_W_8_52 1 R 0x00
@ 52MHz in DDR mode
Minimum Read Performance for 8bit
[234] MIN_PERF_DDR_R_8_52 1 R 0x64
@ 52MHz in DDR mode
[233] Reserved - 1 - 0x00
[232] TRIM Multiplier TRIM_MULT 1 R 0x01
[231] Secure Feature support SEC_FEATURE_SUPPORT 1 R 0x55
[230] Secure Erase Multiplier SEC_ERASE_MULT 1 R 0xF3
[229] Secure TRIM Multiplier SEC_TRIM_MULT 1 R 0xF7
[228] Boot information BOOT_INFO 1 R 0x07
[227] Reserved - 1 - 0x00
[226] Boot partition size BOOT_SIZE_MULTI 1 R 0x20
[225] Access size ACC_SIZE 1 R 0x08
[224] High-capacity erase unit size HC_ERASE_GRP_SIZE 1 R 0x08
[223] High-capacity erase timeout ERASE_TIMEOUT_MULT 1 R 0x11
[222] Reliable write sector count REL_WR_SEC_C 1 R 0x01
[221] High-capacity write protect group size HC_WP_GRP_SIZE 1 R 0x01
[220] Sleep current (Vcc) S_C_VCC 1 R 0x07
[219] Sleep current (VccQ) S_C_VCCQ 1 R 0x09
PRODUCTION_STATE
[218] Production state awareness timeout 1 R 0x0A
_AWARENESS_TIMEOUT
[217] Sleep/awake timeout S_A_TIMEOUT 1 R 0x14
[216] Sleep Notification Timeout SLEEP_NOTIFICATION_TIME 1 R 0x10
[215:212] Sector Count SEC_COUNT 4 R 0x01D5A000
[211] Secure Write Protection Information SECURE_WP_INFO 1 R 0x01
Minimum Write Performance for 8bit
[210] MIN_PERF_W_8_52 1 R 0x00
@ 52MHz
Minimum Read Performance 8bit
[209] MIN_PERF_R_8_52 1 R 0x78
@ 52MHz
Minimum Write Performance for 8bit
[208] MIN_PERF_W_8_26_4_52 1 R 0x00
@ 26MHz, for 4bit at 52MHz
Minimum Read Performance for 8 bit
[207] MIN_PERF_R_8_26_4_52 1 R 0x46
@ 26MHz, for 4bit at 52MHz
Minimum Write Performance for 4bit
[206] MIN_PERF_W_4_26 1 R 0x00
@ 26MHz
Minimum Read Performance for 4bit
[205] MIN_PERF_R_4_26 1 R 0x1E
@ 26MHz

9 Sep. 17th, 2015

 THGBMHG7C1LBAIL

Size
CSD-slice Name Field Cell Type Value
(Bytes)

[204] Reserved - 1 - 0x00

[203] Power class for 26MHz @ 3.6V PWR_CL_26_360 1 R 0x55

[202] Power class for 52MHz @ 3.6V PWR_CL_52_360 1 R 0x55

[201] Power class for 26MHz @ 1.95V PWR_CL_26_195 1 R 0xBB
[200] Power class for 52MHz @ 1.95V PWR_CL_52_195 1 R 0xBB
[199] Partition switching timing PARTITION_SWITCH_TIME 1 R 0x0A
[198] Out-of-interrupt busy timing OUT_OF_INTERRUPT_TIME 1 R 0x0A
[197] I/O Driver Strength DRIVER_STRENGTH 1 R 0x1F

[196] Device Type DEVICE_TYPE 1 R 0x57

[195] Reserved - 1 - 0x00
[194] CSD structure CSD_STRUCTURE 1 R 0x02
[193] Reserved - 1 - 0x00
[192] Extended CSD revision EXT_CSD_REV 1 R 0x08
[191] Command Set CMD_SET 1 R/W/E_P 0x00
[190] Reserved - 1 - 0x00
[189] Command set revision CMD_SET_REV 1 R 0x00
[188] Reserved - 1 - 0x00
[187] Power class 1 POWER_CLASS 1 R/W/E_P 0x00
[186] Reserved - 1 - 0x00
[185] High-speed interface timing HS_TIMING 1 R/W/E_P 0x00
[184] Strobe Support STROBE_SUPPORT 1 R 0x01
[183] Bus width mode BUS_WIDTH 1 W/E_P 0x00
[182] Reserved - 1 - 0x00
[181] Erased memory content ERASED_MEM_CONT 1 R 0x00
[180] Reserved - 1 - 0x00
R/W/E &
[179] Partition configuration PARTITION_CONFIG 1 0x00
R/W/E_P
R/W &
[178] Boot config protection BOOT_CONFIG_PROT 1 0x00
R/W/C_P
[177] Boot bus Conditions BOOT_BUS_CONDITIONS 1 R/W/E 0x00
[176] Reserved - 1 - 0x00
[175] High-density erase group definition ERASE_GROUP_DEF 1 R/W/E_P 0x00
[174] Boot write protection status registers BOOT_WP_STATUS 1 R 0x00
R/W &
[173] Boot area write protection register BOOT_WP 1 0x00
R/W/C_P
[172] Reserved - 1 - 0x00
R/W,
[171] User area write protection register USER_WP 1 R/W/C_P & 0x00
R/W/E_P
[170] Reserved - 1 - 0x00
[169] FW configuration FW_CONFIG 1 R/W 0x00

10 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Size
CSD-slice Name Field Cell Type Value
(Bytes)
[168] RPMB Size RPMB_SIZE_MULT 1 R 0x20
[167] Write reliability setting register WR_REL_SET 1 R/W 0x1F
[166] Write reliability parameter register WR_REL_PARAM 1 R 0x15
[165] Start Sanitize operation SANITIZE_START 1 W/E_P 0x00
[164] Manually start background operations BKOPS_START 1 W/E_P 0x00
R/W
[163] Enable background operations handshake BKOPS_EN 1 & 0x00
R/W/E
[162] H/W reset function RST_n_FUNCTION 1 R/W 0x00

[161] HPI management HPI_MGMT 1 R/W/E_P 0x00

[160] Partitioning Support PARTITIONING_SUPPORT 1 R 0x07

[159:157] Max Enhanced Area Size 2 MAX_ENH_SIZE_MULT 3 R 0x000757

[156] Partitions attribute PARTITIONS_ATTRIBUTE 1 R/W 0x00

PARTITION_SETTING_COMPLE
[155] Partitioning Setting 1 R/W 0x00
TED
[154:143] General Purpose Partition Size 3 GP_SIZE_MULT 12 R/W 0x00

[142:140] Enhanced User Data Area Size 4 ENH_SIZE_MULT 3 R/W 0x00

[139:136] Enhanced User Data Start Address ENH_START_ADDR 4 R/W 0x00

[135] Reserved - 1 - 0x00
[134] Bad Block Management mode SEC_BAD_BLK_MGMNT 1 R/W 0x00
5 PRODUCTION_STATE
[133] Production state awareness 1 R/W/E 0x00
_AWARENESS
1
[132] Package Case Temperature is controlled TCASE_SUPPORT 1 W/E_P 0x00
[131] Periodic Wake-up1 PERIODIC_WAKEUP 1 R/W/E 0x00
PROGRAM_CID_CSD_DDR_SU
[130] Program CID/CSD in DDR mode support 1 R 0x01
PPORT
[129:128] Reserved - 2 - All ‘0’
[127:64] Vendor Specific Fields VENDOR_SPECIFIC_FIELD 64 - -
[63] Native sector size NATIVE_SECTOR_SIZE 1 R 0x01
[62] Sector size emulation USE_NATIVE_SECTOR 1 R/W 0x00
[61] Sector size DATA_SECTOR_SIZE 1 R 0x00
1st initialization
[60] after disabling sector size emulation INI_TIMEOUT_EMU 1 R 0x0A

[59] Class 6 commands control CLASS_6_CTRL 1 R/W/E_P 0x00

[58] Number of addressed group to be Released DYNCAP_NEEDED 1 R 0x00
[57:56] Exception events control EXCEPTION_EVENTS_CTRL 2 R/W/E_P 0x00
[55:54] Exception events status EXCEPTION_EVENTS_STATUS 2 R All ‘0’
1
[53:52] Extended partitions attribute EXT_PARTITIONS_ATTRIBUTE 2 R/W 0x00
[51:37] Context configuration CONTEXT_CONF 15 R/W/E_P 0x00
[36] Packed command status PACKED_COMMAND_STATUS 1 R 0x00
[35] Packed command failure index PACKED_FAILURE_INDEX 1 R 0x00
5
[34] Power Off Notification POWER_OFF_NOTIFICATION 1 R/W/E_P 0x00
[33] Control to turn the Cache ON/OFF CACHE_CTRL 1 R/W/E_P 0x00

11 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Size
CSD-slice Name Field Cell Type Value
(Bytes)
[32] Flushing of the cache FLUSH_CACHE 1 W/E_P 0x00
[31] Control to turn the Barrier ON/OFF BARRIER_CTRL 1 R/W 0x00

[30] Mode config MODE_CONFIG 1 R/W/E_P 0x00

[29] Mode operation codes MODE_OPERATION_CODES 1 W/E_P 0x00

[28:27] Reserved - 2 - All ‘0’

[26] FFU status FFU_STATUS 1 R 0x00
6
[25:22] Pre loading data size PRE_LOADING_DATA_SIZE 4 R/W/E_P 0x00757000
MAX_PRE_LOADING_DATA
[21:18] Max pre loading data size 4 R 0x00757000
_SIZE
PRODUCT_STATE R/W/E
[17] Product state awareness enablement5 1 0x03
_AWARENESS_ENABLEMENT &R
[16] Secure Removal Type SECURE_REMOVAL_TYPE 1 R/W & R 0x39
[15] Command Queue Mode Enable CMDQ_MODE_EN 1 R/W/E_P 0x00
[14:0] Reserved - 15 - All ‘0’

1 Although these fields can be re-written by host, TOSHIBA e-MMC does not support.

2 Max Enhanced Area Size (MAX_ENH_SIZE_MULT [159:157]) has to be calculated by following formula.
Max Enhanced Area = MAX_ENH_SIZE_MULT x HC_WP_GRP_SIZE x HC_ERASE_GRP_SIZE x 512kBytes
4

 Enhanced generalpartition sizei  Enhanceduser data area  Max enhancedarea

i1

3 General Purpose Partition Size (GP_SIZE_MULT_GP0 - GP_SIZE_MULT_GP3 [154:143]) has to be calculated

by following formula.
16 8
General_Purpose_Partition_X Size = (GP_SIZE_MULT_X_2 x 2 + GP_SIZE_MULT_X_1 x 2
0
+ GP_SIZE_MULT_X_0 x 2 ) x HC_WP_GRP_SIZE
x HC_ERASE_GRP_SIZE x 512kBytes

4 Enhanced User Data Area Size (ENH_SIZE_MULT [142:140]) has to be calculated by following formula.

16 8
Enhanced User Data Area x Size = (ENH_SIZE_MULT_2 x 2 + ENH_SIZE_MULT_1 x 2
0
+ ENH_SIZE_MULT_0 x 2 ) x HC_WP_GRP_SIZE
x HC_ERASE_GRP_SIZE x 512kBytes

5
Toshiba recommends to issue the Power Off Notification before turning off the device, especially when cache is
on or AUTO_EN(BKOPS_EN[163]:bit1) is set to ‘1b’.

12 Sep. 17th, 2015

 THGBMHG7C1LBAIL
6
- Pre loading data size = PRE_LOADING_DATA_SIZE x Sector Size
Pre-loading data size should be multiple of 4KB and the pre-loading data should be written by multiple of 4KB
chunk size, aligned with 4KB address. This is because the valid data size will be treated as 4KB when host
writes data less than 4KB.

- If the host continues to write data in Normal state (after it wrote PRE_LOADING_DATA_SIZE amount
of data) and before soldering, the pre-loading data might be corrupted after soldering.

- If a power cycle is occurred during the data transfer, the amount of data written to device is not clear.
Therefore in this case, host should erase the entire pre-loaded data and set again
PRE_LOADING_DATA_SIZE[25:22], PRODUCTION_STATE_AWARENESS[133], and
PRODUCT_STATE_AWARENESS_ENABLEMENT[17].

13 Sep. 17th, 2015

 THGBMHG7C1LBAIL
ELECTRICAL CHARACTERISTICS
DC Characteristics
Absolute Maximum Ratings
The absolute maximum ratings of a semiconductor device are a set of specified parameter values, which must
not be exceeded during operation, even for an instant.
If any of these rating would be exceeded during operation, the device electrical characteristics may be irreparably
altered and the reliability and lifetime of the device can no longer be guaranteed. Moreover, these operations with
exceeded ratings may cause break down, damage, and/or degradation to any other equipment. Applications using
the device should be designed such that each maximum rating will never be exceeded in any operating conditions.
Before using, creating, and/or producing designs, refer to and comply with the precautions and conditions set forth
in this document.
Parameter Symbol Test Conditions Min Max Unit

Supply voltage 1 VCC -0.5 4.1 V

Supply voltage 2 VccQ -0.5 4.1 V

Voltage Input VIO -0.5 VccQ+0.5(≤4.1) V

General
Parameter Symbol Test Conditions Min Max Unit
Peak voltage on all lines -0.5 VccQ+0.5 V
All Inputs

Input Leakage Current (before initialization sequence1

-100 100 μA
and/or the internal pull up resistors connected)

Input Leakage Current (after initialization sequence and

-2 2 μA
the internal pull up resistors disconnected)

All Outputs

Output Leakage Current (before initialization sequence) -100 100 μA

Output Leakage Current (after initialization sequence) -2 2 μA

1) Initialization sequence is defined in Power-Up chapter of JEDEC/MMCA Standard

Power Supply Voltage

Parameter Symbol Test Conditions Min Max Unit

Supply voltage 1 VCC 2.7 3.6 V

1.7 1.95 V
Supply voltage 2 VccQ
2.7 3.6 V

1) Once the power supply VCC or VCCQ falls below the minimum guaranteed voltage (for example, upon sudden power fail),
the voltage level of VCC or VCCQ shall be kept less than 0.5 V for at least 1ms before it goes beyond 0.5 V again.

14 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Supply Current
Interleave Min Max
Parameter Symbol Mode VccQ Unit
Operation Iccq Icc Iccq Icc
1.8V   95 15
SDR mA
3.3V   110 15

1.8V   115 20
Read IROP Non Interleave DDR mA
3.3V   140 20

HS200 1.8V   170 35 mA

Operation HS400 1.8V   215 40 mA

(RMS) 1.8V   60 40
SDR mA
3.3V   65 40

1.8V   65 45
Write IWOP Non Interleave DDR mA
3.3V   70 45

HS200 1.8V   75 55 mA
HS400 1.8V   80 55 mA

15 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Internal resistance and Device capacitance
Parameter Symbol Test Conditions Min Max Unit

Single device capacitance CDEVICE  6 pF

Internal pull up resistance DAT1 – DAT7 RINT 10 150 KΩ

Bus Signal Levels

Open-Drain Mode Bus Signal Level

Parameter Symbol Min Max Unit Conditions

Output HIGH voltage VOH VCCQ - 0.2  V NOTE 1

Output LOW voltage VOL  0.3 V IOL = 2 mA

NOTE 1: Because VOH depends on external resistance value (including outside the package), this value does not apply as device
specification. Host is responsible to choose the external pull-up and open drain resistance value to meet VOH Min value.

Push-Pull Mode Bus Signal Level (High-Voltage)

Parameter Symbol Min Max Unit Conditions

Output HIGH voltage VOH 0.75 * VCCQ  V IOH = -100 μA @ VCCQ min

Output LOW voltage VOL  0.125 * VCCQ V IOL = 100 μA @ VCCQ min

Input HIGH voltage VIH 0.625 * VCCQ VCCQ + 0.3 V

Input LOW voltage VIL VSS - 0.3 0.25 * VCCQ V

Push-Pull Mode Bus Signal Level (Dual-Voltage)

Parameter Symbol Min Max Unit Conditions

Output HIGH voltage VOH VCCQ - 0.45  V IOH = -2mA

Output LOW voltage VOL  0.45 V IOL = 2mA

Input HIGH voltage VIH 0.65 * VCCQ VCCQ + 0.3 V

Input LOW voltage VIL VSS - 0.3 0.35 * VCCQ V

16 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Driver Types Definition
In JEDEC, Driver Type-0 is defined as mandatory for e-MMC HS200&HS400 Device. While four additional Driver
Types (1, 2, 3 and 4) are defined as optional, to allow the support of wider Host loads. The Host may select the most
appropriate Driver Type of the Device (if supported) to achieve optimal signal integrity performance.

Driver Type-0 is targeted for transmission line, based distributed system with 50Ω nominal line impedance.
Therefore, it is defined as 50Ω nominal driver. The nominal line impedance should be kept as 50Ω even if Driver Type
would be changed.
For HS200, when tested with CL = 15pF Driver Type-0 shall meet all AC characteristics and HS200 Device output
timing requirements. The test circuit defined in section 10.5.4.3 of JEDEC/MMCA Standard 5.1 is used for testing of
Driver Type-0.
For HS400, when tested with the reference load defined in page 28 HS400 reference load figure, Driver Type-0 or
Driver Type-1 or Driver Type-4 shall meet all AC characteristics and HS400 Device output timing requirements.

Driver TOSHIBA Nominal Impedance Approximated driving capability

Remark
Type e-MMC (Driver strength) compared to Type-0

0 Supported 50 Ω (18mA) x1 Default Driver Type

Recommendation at HS400 under the

1 Supported 33 Ω (27mA) x1.5 condition of JEDEC standard
reference load.

2 Supported 66 Ω (14mA) x0.75

3 Supported 100 Ω (9mA) x0.5

Recommendation at HS400 under the

4 Supported 40 Ω (23mA) X1.2 condition of JEDEC standard
reference load.

1) Nominal impedance is defined by I-V characteristics of output driver at 0.9V when VCCQ = 1.8V.

*The most suitable setting for user’s operating environment should be selected.
At HS400, Toshiba recommends Driver Type-1 and Type-4. This is because they meet all AC characteristics and
Device output timing requirements under the condition of JEDEC standard reference load.

17 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Bus Timing

Device Interface Timings (High-speed interface timing)

Parameter Symbol Min Max Unit Remark
(1)
Clock CLK

CL ≤ 30pF
Clock frequency Data Transfer Mode (PP)(2) fpp 0 52(3) MHz
Tolerance: +100KHz
Clock frequency Identification Mode (OD) fOD 0 400 KHz Tolerance: +20KHz
Clock high time tWH 6.5  ns CL ≤ 30pF
Clock low time tWL 6.5  ns CL ≤ 30pF

Clock rise time (4)

tTLH  3 ns CL ≤ 30pF

Clock fall time tTHL  3 ns CL ≤ 30pF

Inputs CMD, DAT (referenced to CLK)

Input set-up time tISU 3  ns CL ≤ 30pF

Input hold time tIH 3  ns CL ≤ 30pF

Outputs CMD, DAT (referenced to CLK)

Output Delay time during Data Transfer tODLY  13.7 ns CL ≤ 30pF

Output hold time tOH 2.5  ns CL ≤ 30pF

Signal rise time (5)

trise  3 ns CL ≤ 30pF

Signal fall time tfall  3 ns CL ≤ 30pF

1) CLK timing is measured at 50% of VCCQ

2) This product shall support the full frequency range from 0 MHz - 26 MHz, or 0 MHz - 52 MHz
3) Device can operate as high-speed interface timing at 26MHz clock frequency.
4) CLK rise and fall times are measured by min (VIH) and max (VIL).
5) Inputs CMD, DAT rise and fall times area measured by min (VIH) and max (VIL), and outputs CMD, DAT rise and fall times
are measured by min (VOH) and max (VOL).

18 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Device Interface Timings (Backward-compatible interface timing)
Parameter Symbol Min Max Unit Remark(1)

Clock CLK(2)

Clock frequency Data Transfer Mode (PP)(3) fpp 0 26 MHz CL ≤ 30pF

Clock frequency Identification Mode (OD) fOD 0 400 KHz

Clock high time tWH 10  ns CL ≤ 30pF

Clock low time tWL 10  ns CL ≤ 30pF

Clock rise time(4) tTLH  10 ns CL ≤ 30pF

Clock fall time tTHL  10 ns CL ≤ 30pF

Inputs CMD,DAT (referenced to CLK)

Input set-up time tISU 3  ns CL ≤ 30pF

Input hold time tIH 3  ns CL ≤ 30pF

Outputs CMD,DAT (referenced to CLK)

Output set-up time(5) tOSU 11.7  ns CL ≤ 30pF

Output hold time(5) tOH 8.3  ns CL ≤ 30pF

1) The e-MMC must always start with the backward-compatible interface timing. The timing mode can be switched to
high-speed interface timing by the host sending the SWITCH command (CMD6) with the argument for high-speed
interface select.
2) CLK timing is measured at 50% of VCCQ
3) For compatibility with e-MMCs that support the v4.2 standard or earlier, host should not use >26MHz before switching to
high-speed interface timing.
4) CLK rise and fall times are measured by min (VIH) and max (VIL).
5) tOSU and tOH are defined as values from clock rising edge. However, the e-MMC device will utilize clock falling edge to
output data in backward compatibility mode. Therefore, it is recommended for hosts either to set tWL value as long as
possible within the range which will not go over tCK - tOHmin) in the system or to use slow clock frequency, so that host
could have data set up margin for the device.
Toshiba e-MMC device utilize clock falling edge to output data in backward compatibility mode.
Host should optimize the timing in order to have data set up margin as follows.

tWL

CLK

tODLY tOSU tOH

Output Invalid Data

tOSU (min) = tWL(min) - tODLY(max 8ns)

Figure 2 Output timing

19 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Bus Timing for DAT signals for during 2x data rate operation
These timings applies to the DAT[7:0] signals only when the device is configured for dual data mode operation. In
this dual data mode, the DAT signals operates synchronously of both the rising and the falling edges of CLK. The
CMD signal still operates synchronously of the rising edge of CLK and therefore complies with the bus timing
specified in High-speed interface timing or Backward-compatible interface timing.

High-speed dual data rate interface timings

Parameter Symbol Min Max Unit Remark

Input CLK (1)

Clock duty cycle 45 55 % Includes jitter, phase noise

Clock rise time tTLH  3 ns CL ≤ 30pF

Clock fall time tTHL  3 ns CL ≤ 30pF

Input CMD(referenced to CLK-SDR mode)

Input set-up time tISUddr 3  ns CL ≤ 20pF

Input hold time tIHddr 3  ns CL ≤ 20pF

Output CMD(referenced to CLK-SDR mode)

Output delay time during data transfer tODLY  13.7 ns CL ≤ 20pF

Output hold time tOH 2.5  ns CL ≤ 20pF

Signal rise time tRISE  3 ns CL ≤ 20pF

Signal fall time tFALL  3 ns CL ≤ 20pF

20 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Parameter Symbol Min Max Unit Remark

Input DAT (referenced to CLK-DDR mode)

Input set-up time tISUddr 2.5  ns CL ≤ 20pF

Input hold time tIHddr 2.5  ns CL ≤ 20pF

Output DAT (referenced to CLK-DDR mode)

Output delay time during data transfer tODLYddr 1.5 7 ns CL ≤ 20pF

Signal rise time (all signals) (2) tRISE  2 ns CL ≤ 20pF

Signal fall time (all signals) tFALL  2 ns CL ≤ 20pF

1) CLK timing is measured at 50% of VCCQ.

2) Inputs DAT rise and fall times are measured by min (VIH) and max (VIL), and outputs DAT rise and fall times are
measured by min (VOH) and max (VOL).

21 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Bus Timing Specification in HS200 mode

HS200 Clock Timing

Host CLK Timing in HS200 mode shall conform to the timing specified in following figure and Table. CLK input shall
satisfy the clock timing over all possible operation and environment conditions. CLK input parameters should be
measured while CMD and DAT lines are stable high or low, as close as possible to the Device. The maximum
frequency of HS200 is 200MHz. Hosts can use any frequency up to the maximum that HS200 mode allows.

tPERIOD
VCCQ

VIH
CLOCK
VT
INPUT
VIL

VSS tTLH tTHL

NOTE 1 VIH denote VIH(min.) and VIL denotes VIL(max.).

NOTE 2 VT = 50% of VCCQ, indicates clock reference point for timing measurements.

Symbol Min Max Unit Remark

tPERIOD 5  ns 200MHz (Max.), between rising edges

tTLH, tTHL < 1ns (max.) at 200MHz, CDEVICE=6pF,
tTLH, tTHL  0.2 * tPERIOD ns The absolute maximum value of tTLH, tTHL is 10ns regardless of
clock frequency.
Duty Cycle 30 70 %

HS200 Device Input Timing

tPERIOD
VCCQ

CLOCK
VT
INPUT

VSS

VCCQ tISU tIH

VIH VIH
CMD.DAT[7-0] VALID
INPUT WINDOW
VIL VIL

VSS

NOTE 1 tISU and tIH are measured at VIL(max) and VIH(min).

NOTE 2 VIH denote VIH(min) and VIL denotes VIL(max).

Symbol Min Max Unit Remark

tISU 1.40  ns CDEVICE ≤ 6pF

tIH 0.8  ns CDEVICE ≤ 6pF

22 Sep. 17th, 2015

 THGBMHG7C1LBAIL
HS200 Device Output Timing
tPH parameter is defined to allow device output delay to be longer than t PERIOD. After initialization, the tPH may have
random phase relation to the clock. The Host is responsible to find the optimal sampling point for the Device outputs,
while switching to the HS200 mode.
While setting the sampling point of data, a long term drift, which mainly depends on temperature drift, should be
considered. The temperature drift is expressed by ΔTPH. Output valid data window (tVW) is available regardless of the
drift (ΔTPH) but position of data window varies by the drift.

tPERIOD
VCCQ

CLOCK
VT
INPUT

VSS

tPH tVW VCCQ

VOH VOH
CMD.DAT[7-0] VALID
OUTPUT WINDOW
VOL VOL

VSS

NOTE VOH denotes VOH(min) and VOL denotes VOL(max).

Symbol Min Max Unit Remark 1

Device output momentary phase from CLK input to CMD

tPH 0 2 UI or DAT lines output.
Does not include a long term temperature drift.
Delay variation due to temperature change after tuning.
-350 +1550 Total allowable shift of output valid window (TVW) from
ΔTPH ps last system Tuning procedure
(ΔT = -20 °C) (ΔT = 90 °C ) ΔTPH is 2600ps for ΔT from -25 °C to 125 °C during
operation.
tVW =2.88ns at 200MHz
Using test circuit in following figure including skew
among CMD and DAT lines created by the Device.
tVW 0.575  UI
Host path may add Signal Integrity induced noise,
skews, etc. Expected tVW at Host input is larger than
0.475UI.

NOTE Unit Interval (UI) is one bit nominal time. For example, UI=5ns at 200 MHz.

23 Sep. 17th, 2015

 THGBMHG7C1LBAIL
ΔTPH consideration

Implementation Guide:
Host should design to avoid sampling errors that may be caused by the Δ TPH drift.
It is recommended to perform tuning procedure while Device wakes up, after sleep.
One simple way to overcome the ΔTPH drift is by reduction of operating frequency.

24 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Bus Timing Specification in HS400 mode

HS400 Input Timing

The CMD input timing for HS400 mode is the same as CMD input timing for HS200 mode.

NOTE VT = 50% of VCCQ, indicates clock reference point for timing measurements.

Parameter Symbol Min Max Unit Remark

Input CLK
Cycle time data transfer mode tPERIOD 5  ns 200 MHz(Max), between rising edges
With respect to VT
Slew rate SR 1.125  V/ns With respect to VIH /VIL
Duty cycle distortion tCKDCD 0.0 0.3 ns Allowable deviation from an ideal 50% duty cycle.
With respect to VT
Includes jitter, phase noise
Minimum pulse width tCKMPW 2.2  ns With respect to VT
Input DAT(referenced to CLK)
Input set-up time tISUddr 0.4  ns CDEVICE ≤ 6 pF
With respect to VIH /VIL
Input hold time tIHddr 0.4  ns CDEVICE ≤ 6 pF
With respect to VIH /VIL
Slew rate SR 1.125  V/ns With respect to VIH /VIL

25 Sep. 17th, 2015

 THGBMHG7C1LBAIL
HS400 Device Output Timing
The Data Strobe is used to read data in HS400 mode. The Data Strobe is toggled only during data read or CRC status response.

NOTE VT = 50% of VCCQ, indicates clock reference point for timing measurements.

Parameter Symbol Min Max Unit Remark

Data Strobe
Cycle time data transfer tPERIOD 5  ns 200 MHz(Max), between rising edges
mode With respect to VT
Slew rate SR 1.125  V/ns With respect to VOH/VOL and HS400 reference load
Duty cycle distortion tDSDCD 0.0 0.2 ns Allowable deviation from the input CLK duty cycle
distortion(tCKDCD)
With respect to VT
Includes jitter, phase noise
Minimum pulse width tDSMPW 2.0  ns With respect to VT
Output DAT(referenced to Data Strobe)
Output skew tRQ  0.4 ns With respect to VOH /VOL and HS400 reference load
Output hold skew tRQH  0.4 ns With respect to VOH /VOL and HS400 reference load
Slew rate SR 1.125  V/ns With respect to VOH /VOL and HS400 reference load

26 Sep. 17th, 2015

 THGBMHG7C1LBAIL
HS400 Device Command Output Timing
The Data Strobe is used to response of any command in HS400 mode.

Note : VT = 50% of VCCQ, indicates clock reference point for timing measurements.

Parameter Symbol Min Max Unit Remark

Data Strobe
Cycle time data transfer tPERIOD 5  ns 200 MHz(Max), between rising edges
mode With respect to VT
Slew rate SR 1.125  V/ns With respect to VOH/VOL and HS400 reference load
Duty cycle distortion tDSDCD 0.0 0.2 ns Allowable deviation from the input CLK duty cycle
distortion(tCKDCD)
With respect to VT
Includes jitter, phase noise
Minimum pulse width tDSMPW 2.0  ns With respect to VT
CMD Response (referenced to Data Strobe)
Output skew(CMD) tRQ_CMD  0.4 ns With respect to VOH /VOL and HS400 reference load
Output hold skew(CMD) tRQH_CMD  0.4 ns With respect to VOH /VOL and HS400 reference load
Slew rate SR 1.125  V/ns With respect to VOH /VOL and HS400 reference load

27 Sep. 17th, 2015

 THGBMHG7C1LBAIL

Driver
Device I/O Measurement Point
Z0 = 50 Ohm
Td = 350 ps
CREFERENCE = 4pF

Reference Load

Figure 3 HS400 reference load

HS400 Capacitance
The Data Strobe is used to read data in HS400 mode. The Data Strobe is toggled only during data read or CRC status response.

Parameter Symbol Min Typ. Max Unit Remark

(1)
Pull-up resistance for CMD RCMD 4.7 100 KΩ
(1)
Pull-up resistance for DAT0-7 RDAT 10 100 kΩ
Pull-down resistance for Data Strobe RDS 10 100(1) kΩ
Internal pull up resistance DAT1-DAT7 Rint 10 150 kΩ
Single Device capacitance CDevice 6 pF

NOTE 1 Recommended maximum value is 50 kΩ for 1.8 V interface supply voltages.

28 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Overshoot/Undershoot Specification
VCCQ Unit
1.70V - 1.95V
Maximum peak amplitude allowed for overshoot area. Max 0.9 V
(See Figure Overshoot/Undershoot definition)
Maximum peak amplitude allowed for undershoot area. Max 0.9 V
(See Figure Overshoot/Undershoot definition)
Maximum area above VCCQ Max 1.5 V-ns
(See Figure Overshoot/Undershoot definition)
Maximum area below VSSQ Max 1.5 V-ns
(See Figure Overshoot/Undershoot definition)

Figure 4 Overshoot/Undershoot definition

H/W Reset Operation

Note *1: Device will detect the rising edge of RST_n signal to trigger internal reset sequence

H/W Reset Timings

Symbol Parameter Min Max Unit
tRSTW RST_n pulse width 1  μs
tRSCA RST_n to Command time 200 (1)
 μs
tRSTH RST_n high period (interval time) 1  μs

1) 74 cycles of clock signal required before issuing CMD1 or CMD0 with argument 0xFFFFFFFA
2) During the device internal initialization sequence right after power on, device may not be able to detect RST_n signal,
because the device may not complete loading RST_n_ENABLE bits of the extended CSD register into the controller yet.

29 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Power-up sequence

Supply voltage

Vcc max

Vcc min

VccQ max

VccQ min

0.5V
time

Vccq Power up time Vcc Power up time Vccq Power up time

tPRUL tPRUH tPRUL

Figure 3 Power up sequence

Power-up parameter
Parameter Symbol Min Max Remark

Supply power-up for 3.3V tPRUH 5 μs 35 ms

Supply power-up for 1.8V tPRUL 5 μs 25 ms

30 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Functional restrictions
- Pre loading data size is limited to MAX_PRE_LOADING_DATA_SIZE[21-18] regardless of using
Production
State Awareness function.
- MAX_PRE_LOADING_DATA_SIZE[21-18] value will change when host sets Enhanced User area Partition.

Reliability Guidance

This reliability guidance is intended to notify some guidance related to using raw NAND flash. Although random
bit errors may occur during use, it does not necessarily mean that a block is bad. Generally, a block should be
marked as bad when a program status failure or erase status failure is detected. The other failure modes may be
recovered by a block erase. ECC treatment for read data is mandatory due to the following Data Retention and
Read Disturb failures.

-Write/Erase Endurance
Write/Erase endurance failures may occur in a cell, page, or block, and are detected by doing a status read after
either an auto program or auto block erase operation. The cumulative bad block count will increase along with the
number of write/erase cycles.

-Data Retention
The data in memory may change after a certain amount of storage time. This is due to charge loss or charge gain.
After block erasure and reprogramming, the block may become usable again. Also write/erase endurance
deteriorates data retention capability. The figure below shows a generic trend of relationship between write/erase
endurance and data retention.

-Read Disturb
A read operation may disturb the data in memory. The data may change due to charge gain. Usually, bit errors
occur on other pages in the block, not the page being read. After a large number of read cycles (between block
erases), a tiny charge may build up and can cause a cell to be soft programmed to another state. After block erasure
and reprogramming, the block may become usable again.

Considering the above failure modes, TOSHIBA recommends following usage:

- Please avoid any excessive iteration of resets and initialization sequences (Device identification mode) as far as
possible after power-on, which may result in read disturb failure. The resets include hardware resets and software
resets.
e.g.1) Iteration of the following command sequence, CMD0 - CMD1 ---
The assertion of CMD1 implies a count of internal read operation in Raw NAND.
CMD0: Reset command, CMD1: Send operation command

e.g.2) Iteration of the following commands, CMD30 and/or CMD31

CMD30: Send status of write protection bits, CMD31: Send type of write protection

31 Sep. 17th, 2015

 THGBMHG7C1LBAIL
Document Revision History

Rev 1.0 May. 27th, 2015 - Released as final revision

Rev 1.1 Aug. 3rd, 2015 - Revised explanation of Driver Types Definition.
Rev 2.0 Sep.17th, 2015 - Updated write performance, operating current
- Revised Ext_CSD Register value
- Fixed some typos

32 Sep. 17th, 2015

 THGBMHG7C1LBAIL
RESTRICTIONS ON PRODUCT USE
 Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively "Product") without notice.
 This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission.
 Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the
Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of
all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application
notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the
instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their
own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such
design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts,
diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating
parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR
APPLICATIONS.
 PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH
MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without
limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for
automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions,
safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU
USE PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your
TOSHIBA sales representative.
 Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
 Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
 The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
 ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF
SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES
OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION
AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED
TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
 Do not use or otherwise make available Product or related software or technology for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile
technology products (mass destruction weapons). Product and related software and technology may be controlled under the
applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the
U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited
except in compliance with all applicable export laws and regulations.
 Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES
OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.

33 Sep. 17th, 2015