-
The graphene squeeze-film microphone
Authors:
M. P. Abrahams,
J. Martinez,
P. G. Steeneken,
G. J. Verbiest
Abstract:
Most microphones operate by detecting the sound-pressure induced motion of a membrane. In contrast, here we introduce a microphone that operates by monitoring the sound-pressure-induced modulation of the compressibility of air. By driving a graphene membrane at its resonance frequency, the gas, that is trapped in a squeeze-film beneath it, is compressed at high frequency. Since the stiffness of th…
▽ More
Most microphones operate by detecting the sound-pressure induced motion of a membrane. In contrast, here we introduce a microphone that operates by monitoring the sound-pressure-induced modulation of the compressibility of air. By driving a graphene membrane at its resonance frequency, the gas, that is trapped in a squeeze-film beneath it, is compressed at high frequency. Since the stiffness of the gas film depend on the air pressure, the resonance frequency of the graphene is modulated by variations in sound pressure. We demonstrate that this squeeze-film microphone principle can be used to detect sound and music by tracking the membrane's resonance frequency using a phase-locked loop (PLL). Since the sound detection principle is different from conventional devices, the squeeze-film microphone potentially offers advantages like increased dynamic range, and a lower susceptibility to pressure-induced failure and vibration-induced noise. Moreover, it might be made much smaller, as demonstrated by the microphone in this work that operates using a circular graphene membrane with an area that is more than a factor 1000 smaller than that of MEMS microphones.
△ Less
Submitted 13 June, 2024;
originally announced June 2024.
-
Tuning dissipation dilution in 2D material resonators by MEMS-induced tension
Authors:
M. P. F. Wopereis,
N. Bouman,
S. Dutta,
P. G. Steeneken,
F. Alijani,
G. J. Verbiest
Abstract:
Resonators based on two-dimensional (2D) materials have exceptional properties for application as nanomechanical sensors, which allows them to operate at high frequencies with high sensitivity. However, their performance as nanomechanical sensors is currently limited by their low quality ($Q$)-factor. Here, we make use of micro-electromechanical systems (MEMS) to apply pure in-plane mechanical str…
▽ More
Resonators based on two-dimensional (2D) materials have exceptional properties for application as nanomechanical sensors, which allows them to operate at high frequencies with high sensitivity. However, their performance as nanomechanical sensors is currently limited by their low quality ($Q$)-factor. Here, we make use of micro-electromechanical systems (MEMS) to apply pure in-plane mechanical strain, enhancing both their resonance frequency and Q-factor. In contrast to earlier work, the 2D material resonators are fabricated on the MEMS actuators without any wet processing steps, using a dry-transfer method. A platinum clamp, that is deposited by electron beam-induced deposition, is shown to be effective in fixing the 2D membrane to the MEMS and preventing slippage. By in-plane straining the membranes in a purely mechanical fashion, we increase the tensile energy, thereby diluting dissipation. This way, we show how dissipation dilution can increase the $Q$-factor of 2D material resonators by 91\%. The presented MEMS actuated dissipation dilution method does not only pave the way towards higher $Q$-factors in resonators based on 2D materials, but also provides a route toward studies of the intrinsic loss mechanisms of 2D materials in the monolayer limit.
△ Less
Submitted 1 March, 2024; v1 submitted 13 January, 2024;
originally announced January 2024.
-
Optomechanical methodology for characterizing the thermal properties of 2D materials
Authors:
Hanqing Liu,
Hatem Brahmi,
Carla Boix-Constant,
Herre S. J. van der Zant,
Peter G. Steeneken,
Gerard J. Verbiest
Abstract:
Heat transport in two-dimensions is fundamentally different from that in three dimensions. As a consequence, the thermal properties of 2D materials are of great interest, both from scientific and application point of view. However, few techniques are available for accurate determination of these properties in ultrathin suspended membranes. Here, we present an optomechanical methodology for extract…
▽ More
Heat transport in two-dimensions is fundamentally different from that in three dimensions. As a consequence, the thermal properties of 2D materials are of great interest, both from scientific and application point of view. However, few techniques are available for accurate determination of these properties in ultrathin suspended membranes. Here, we present an optomechanical methodology for extracting the thermal expansion coefficient, specific heat and thermal conductivity of ultrathin membranes made of 2H-TaS2, FePS3, polycrystalline silicon, MoS2 and WSe2. The obtained thermal properties are in good agreement with values reported in the literature for the same materials. Our work provides an optomechanical method for determining thermal properties of ultrathin suspended membranes, that are difficult to measure otherwise. It can does provide a route towards improving our understanding of heat transport in the 2D limit and facilitates engineering of 2D structures with dedicated thermal performance.
△ Less
Submitted 10 December, 2023;
originally announced December 2023.
-
Quantifying stress distribution in ultra-large graphene drums through mode shape imaging
Authors:
Ali Sarafraz,
Hanqing Liu,
Katarina Cvetanović,
Marko Spasenović,
Sten Vollebregt,
Tomas Manzaneque Garcia,
Peter G. Steeneken,
Farbod Alijani,
Gerard J. Verbiest
Abstract:
Suspended drums made of 2D materials hold potential for sensing applications. However, the industrialization of these applications is hindered by significant device-to-device variations presumably caused by non-uniform stress distributions induced by the fabrication process. Here we introduce a new methodology to determine the stress distribution from their mechanical resonance frequencies and cor…
▽ More
Suspended drums made of 2D materials hold potential for sensing applications. However, the industrialization of these applications is hindered by significant device-to-device variations presumably caused by non-uniform stress distributions induced by the fabrication process. Here we introduce a new methodology to determine the stress distribution from their mechanical resonance frequencies and corresponding mode shapes as measured by a laser Doppler vibrometer (LDV). To avoid limitations posed by the optical resolution of the LDV, we leverage a unique manufacturing process to create ultra-large graphene drums with diameters of up to 1000 um. We solve the inverse problem of a Föppl--von Kármán plate model by an iterative procedure to obtain the stress distribution within the drums from the experimental data. Our results show that the generally used uniform pre-tension assumption overestimates the pre-stress value, exceeding the averaged stress obtained by more than 47%. Moreover, it is is found that the reconstructed stress distributions are bi-axial, which likely originates from the transfer process. The introduced metholodogy allows one to estimate the tension distribution in drum resonators from their mechanical response and thereby paves the way for linking the used fabrication processes to the resulting device performance.
△ Less
Submitted 2 November, 2023; v1 submitted 1 November, 2023;
originally announced November 2023.
-
Enhanced sensitivity and tunability of thermomechanical resonance near the buckling bifurcation
Authors:
Hanqing Liu,
Gabriele Baglioni,
Carla B. Constant,
Herre S. J. van der Zant,
Peter G. Steeneken,
Gerard J. Verbiest
Abstract:
The high susceptibility of ultrathin two-dimensional (2D) material resonators to force and temperature makes them ideal systems for sensing applications and exploring thermomechanical coupling. Although the dynamics of these systems at high stress has been thoroughly investigated, their behavior near the buckling transition has received less attention. Here, we demonstrate that the force sensitivi…
▽ More
The high susceptibility of ultrathin two-dimensional (2D) material resonators to force and temperature makes them ideal systems for sensing applications and exploring thermomechanical coupling. Although the dynamics of these systems at high stress has been thoroughly investigated, their behavior near the buckling transition has received less attention. Here, we demonstrate that the force sensitivity and frequency tunability of 2D material resonators are significantly enhanced near the buckling bifurcation. This bifurcation is triggered by compressive displacement that we induce via thermal expansion of the devices, while measuring their dynamics via an optomechanical technique. We understand the frequency tuning of the devices through a mechanical buckling model, which allows to extract the central deflection and boundary compressive displacement of the membrane. Surprisingly, we obtain a remarkable enhancement of up to 14x the vibration amplitude attributed to a very low stiffness of the membrane at the buckling transition, as well as a high frequency tunability by temperature of more than 4.02 %/K. The presented results provide insights into the effects of buckling on the dynamics of free-standing 2D materials and thereby open up opportunities for the realization of 2D resonant sensors with buckling-enhanced sensitivity.
△ Less
Submitted 7 December, 2023; v1 submitted 1 May, 2023;
originally announced May 2023.
-
Nanomechanical resonators fabricated by atomic layer deposition on suspended 2D materials
Authors:
Hanqing Liu,
Saravana B. Basuvalingam,
Saurabh Lodha,
Ageeth A. Bol,
Herre S. J. van der Zant,
Peter G. Steeneken,
G. J. Verbiest
Abstract:
Atomic layer deposition (ALD), a layer-by-layer controlled method to synthesize ultrathin materials, provides various merits over other techniques such as precise thickness control, large area scalability and excellent conformality. Here we demonstrate the possibility of using ALD growth on top of suspended 2D materials to fabricate nanomechanical resonators. We fabricate ALD nanomechanical resona…
▽ More
Atomic layer deposition (ALD), a layer-by-layer controlled method to synthesize ultrathin materials, provides various merits over other techniques such as precise thickness control, large area scalability and excellent conformality. Here we demonstrate the possibility of using ALD growth on top of suspended 2D materials to fabricate nanomechanical resonators. We fabricate ALD nanomechanical resonators consisting of a graphene/MoS$_2$ heterostructure. Using AFM indentation and optothermal drive, we measure their mechanical properties including Young's modulus, resonance frequency and quality factor, showing similar values as their exfoliated and chemical vapor deposited counterparts. We also demonstrate the fabrication of nanomechanical resonators by exfoliating an ALD grown NbS$_2$ layer. This study exemplifies the potential of ALD techniques to produce high-quality suspended nanomechanical membranes, providing a promising route towards high-volume fabrication of future multilayer nanodevices and nanoelectromechanical systems.
△ Less
Submitted 16 December, 2022;
originally announced December 2022.
-
Ultra-sensitive graphene membranes for microphone applications
Authors:
Gabriele Baglioni,
Roberto Pezone,
Sten Vollebregt,
Katarina Cvetanovic,
Marko Spasenovic,
Dejan Todorovic,
Hanqing Liu,
Gerard J. Verbiest,
Herre S. J. van der Zant,
y,
Peter G. Steeneken
Abstract:
Microphones exploit the motion of suspended membranes to detect sound waves. Since the microphone performance can be improved by reducing the thickness and mass of its sensing membrane, graphene-based microphones are expected to outperform state-of-the-art microelectromechanical (MEMS) microphones and allow further miniaturization of the device. Here, we present a laser vibrometry study of the aco…
▽ More
Microphones exploit the motion of suspended membranes to detect sound waves. Since the microphone performance can be improved by reducing the thickness and mass of its sensing membrane, graphene-based microphones are expected to outperform state-of-the-art microelectromechanical (MEMS) microphones and allow further miniaturization of the device. Here, we present a laser vibrometry study of the acoustic response of suspended multilayer graphene membranes for microphone applications. We address performance parameters relevant for acoustic sensing, including mechanical sensitivity, limit of detection and nonlinear distortion, and discuss the trade-offs and limitations in the design of graphene microphones. We demonstrate superior mechanical sensitivities of the graphene membranes, reaching more than 2 orders of magnitude higher compliances than commercial MEMS devices, and report a limit of detection as low as 15 dBSPL, which is 10 - 15 dB lower than that featured by current MEMS microphones.
△ Less
Submitted 7 November, 2022;
originally announced November 2022.
-
Conoscopic interferometry for optimal acoustic pulse detection in ultrafast acoustics
Authors:
Martin Robin,
Ruben Guis,
Mustafa Umit Arabul,
Zili Zhou,
Nitesh Pandey,
Gerard J. Verbiest
Abstract:
Conoscopic interferometry is a promising detection technique for ultrafast acoustics. By focusing a probe beam through a birefringent crystal before passing it through a polarizer, conoscopic interferences sculpt the spatial profile of the beam. The use of these patterns for acoustic wave detection revealed a higher detection sensitivity over existing techniques, such as reflectometry and beam dis…
▽ More
Conoscopic interferometry is a promising detection technique for ultrafast acoustics. By focusing a probe beam through a birefringent crystal before passing it through a polarizer, conoscopic interferences sculpt the spatial profile of the beam. The use of these patterns for acoustic wave detection revealed a higher detection sensitivity over existing techniques, such as reflectometry and beam distortion detection. However, the physical origin of the increased sensitivity is unknown. In this work, we present a model, describing the sensitivity behaviour of conoscopic interferometry with respect to the quarter-wave plate orientation and the diaphragm aperture, which is validated experimentally. Using the model, we optimize the detection sensitivity of conoscopic interferometry. We obtain a maximal sensitivity of detection when placing the diaphragm edge on the dark fringes of the conoscopic interference patterns. In the configurations studied in this work, conoscopic interferometry can be 8x more sensitive to acoustic waves than beam distortion detection.
△ Less
Submitted 6 November, 2022;
originally announced November 2022.
-
Tension tuning of sound and heat transport in graphene
Authors:
H. Liu,
M. Lee,
M. Šiškins,
H. S. J. van der Zant,
P. G. Steeneken,
G. J. Verbiest
Abstract:
Heat transport by acoustic phonons in 2D materials is fundamentally different from that in 3D crystals because the out-of-plane phonons propagate in a unique way that strongly depends on tension and bending rigidity. Since in-plane and out-of-plane phonon baths are decoupled, initial studies suggested they provide independent pathways for heat transport and storage in 2D materials. Here, we induce…
▽ More
Heat transport by acoustic phonons in 2D materials is fundamentally different from that in 3D crystals because the out-of-plane phonons propagate in a unique way that strongly depends on tension and bending rigidity. Since in-plane and out-of-plane phonon baths are decoupled, initial studies suggested they provide independent pathways for heat transport and storage in 2D materials. Here, we induce tension in freestanding graphene membranes by electrostatic force, and use optomechanical techniques to demonstrate that it can change the rate of heat transport by as much as 33%. Using a ballistic Debye model, we account for these observations and extract the average bending rigidity of the flexural acoustic phonons, which increases approximately linearly with the membrane's areal mass density, in contrast to the cubic dependence seen in bulk structures. Thus, we not only elucidate phononic heat transport mechanisms in suspended 2D materials, but also provide a promising route for controlling nanoscale heat transport by tension.
△ Less
Submitted 14 April, 2022;
originally announced April 2022.
-
Self-sealing complex oxide resonators
Authors:
Martin Lee,
Martin Robin,
Ruben Guis,
Ulderico Filippozzi,
Dong Hoon Shin,
Thierry C. van Thiel,
Stijn Paardekooper,
Johannes R. Renshof,
Herre S. J. van der Zant,
Andrea D. Caviglia,
Gerard J. Verbiest,
Peter G. Steeneken
Abstract:
Although 2D materials hold great potential for next-generation pressure sensors, recent studies revealed that gases permeate along the membrane-surface interface that is only weakly bound by van der Waals interactions, necessitating additional sealing procedures. In this work, we demonstrate the use of free-standing complex oxides as self-sealing membranes that allow the reference cavity of pressu…
▽ More
Although 2D materials hold great potential for next-generation pressure sensors, recent studies revealed that gases permeate along the membrane-surface interface that is only weakly bound by van der Waals interactions, necessitating additional sealing procedures. In this work, we demonstrate the use of free-standing complex oxides as self-sealing membranes that allow the reference cavity of pressure sensors to be sealed by a simple anneal. To test the hermeticity, we study the gas permeation time constants in nano-mechanical resonators made from SrRuO3 and SrTiO3 membranes suspended over SiO2/Si cavities which show an improvement up to 4 orders of magnitude in the permeation time constant after annealing the devices for 15 minutes. Similar devices fabricated on Si3N4/Si do not show such improvements, suggesting that the adhesion increase over SiO2 is mediated by oxygen bonds that are formed at the SiO2/complex oxide interface during the self-sealing anneal. We confirm the enhancement of adhesion by picosecond ultrasonics measurements which show an increase in the interfacial stiffness by 70% after annealing. Since it is straigthforward to apply, the presented self-sealing method is thus a promising route toward realizing ultrathin hermetic pressure sensors.
△ Less
Submitted 8 September, 2021;
originally announced September 2021.
-
Optical absorption sensing with dual-spectrum silicon LEDs in SOI-CMOS technology
Authors:
Satadal Dutta,
Peter G. Steeneken,
Gerard J. Verbiest
Abstract:
Silicon p-n junction diodes emit low-intensity, broad-spectrum light near 1120 nm in forward bias and between 400-900 nm in reverse bias (avalanche). For the first time, we experimentally achieve optical absorption sensing of pigment in solution with silicon micro LEDs designed in a standard silicon-on-insulator CMOS technology. By driving a single LED in both forward and avalanche modes of operat…
▽ More
Silicon p-n junction diodes emit low-intensity, broad-spectrum light near 1120 nm in forward bias and between 400-900 nm in reverse bias (avalanche). For the first time, we experimentally achieve optical absorption sensing of pigment in solution with silicon micro LEDs designed in a standard silicon-on-insulator CMOS technology. By driving a single LED in both forward and avalanche modes of operation, we steer its electroluminescent spectrum between visible and near-infrared (NIR). We then characterize the vertical optical transmission of both visible and NIR light from the LED through the same micro-droplet specimen to a vertically mounted discrete silicon photodiode. The effective absorption coefficient of carmine solution in glycerol at varying concentrations were extracted from the color ratio in optical coupling. By computing the LED-specific molar absorption coefficient of carmine, we estimate the concentration (0.040 mo/L) and validate the same with a commercial spectrophotometer (0.030 mol/L ). With a maximum observed sensitivity of 1260 /cm /mol L, the sensor is a significant step forward towards low-cost CMOS-integrated optical sensors with silicon LED as the light source intended for biochemical analyses in food sector and plant/human health.
△ Less
Submitted 14 December, 2020;
originally announced December 2020.
-
Nanoelectromechanical Sensors based on Suspended 2D Materials
Authors:
Max C. Lemme,
Stefan Wagner,
Kangho Lee,
Xuge Fan,
Gerard J. Verbiest,
Sebastian Wittmann,
Sebastian Lukas,
Robin J. Dolleman,
Frank Niklaus,
Herre S. J. van der Zant,
Georg S. Duesberg,
Peter G. Steeneken
Abstract:
The unique properties and atomic thickness of two-dimensional (2D) materials enable smaller and better nanoelectromechanical sensors with novel functionalities. During the last decade, many studies have successfully shown the feasibility of using suspended membranes of 2D materials in pressure sensors, microphones, accelerometers, and mass and gas sensors. In this review, we explain the different…
▽ More
The unique properties and atomic thickness of two-dimensional (2D) materials enable smaller and better nanoelectromechanical sensors with novel functionalities. During the last decade, many studies have successfully shown the feasibility of using suspended membranes of 2D materials in pressure sensors, microphones, accelerometers, and mass and gas sensors. In this review, we explain the different sensing concepts and give an overview of the relevant material properties, fabrication routes, and device operation principles. Finally, we discuss sensor readout and integration methods and provide comparisons against the state of the art to show both the challenges and promises of 2D material-based nanoelectromechanical sensing.
△ Less
Submitted 23 July, 2020;
originally announced July 2020.
-
Tunable coupling of two mechanical resonators by a graphene membrane
Authors:
G. J. Verbiest,
M. Goldsche,
J. Sonntag,
T. Khodkov,
N. von den Driesch,
D. Buca,
C. Stampfer
Abstract:
Coupled nanomechanical resonators are interesting for both fundamental studies and practical applications as they offer rich and tunable oscillation dynamics. At present, the mechanical coupling in such systems is often mediated by a fixed geometry, such as a joint clamping point of the resonators or a displacement-dependent force. Here we show a graphene-integrated electromechanical system consis…
▽ More
Coupled nanomechanical resonators are interesting for both fundamental studies and practical applications as they offer rich and tunable oscillation dynamics. At present, the mechanical coupling in such systems is often mediated by a fixed geometry, such as a joint clamping point of the resonators or a displacement-dependent force. Here we show a graphene-integrated electromechanical system consisting of two physically separated mechanical resonators -- a comb-drive actuator and a suspended silicon beam -- that are tunably coupled by a graphene membrane. The graphene membrane, moreover, provides a sensitive electrical read-out for the two resonating systems silicon structures showing 16 different modes in the frequency range from 0.4~to 24~MHz. In addition, by pulling on the graphene membrane with an electrostatic potential applied to one of the silicon resonators, we control the mechanical coupling, quantified by the $g$-factor, from 20 kHz to 100 kHz. Our results pave the way for coupled nanoelectromechanical systems requiring controllable mechanically coupled resonators.
△ Less
Submitted 6 November, 2020; v1 submitted 11 May, 2020;
originally announced May 2020.
-
Phonon Scattering at Kinks in Suspended Graphene
Authors:
Robin J. Dolleman,
Yaroslav M. Blanter,
Herre S. J. van der Zant,
Peter G. Steeneken,
Gerard J. Verbiest
Abstract:
Recent experiments have shown surprisingly large thermal time constants in suspended graphene ranging from 10 to 100 ns in drums with a diameter ranging from 2 to 7 microns. The large time constants and their scaling with diameter points towards a thermal resistance at the edge of the drum. However, an explanation of the microscopic origin of this resistance is lacking. Here, we show how phonon sc…
▽ More
Recent experiments have shown surprisingly large thermal time constants in suspended graphene ranging from 10 to 100 ns in drums with a diameter ranging from 2 to 7 microns. The large time constants and their scaling with diameter points towards a thermal resistance at the edge of the drum. However, an explanation of the microscopic origin of this resistance is lacking. Here, we show how phonon scattering at a kink in the graphene, e.g. formed by sidewall adhesion at the edge of the suspended membrane, can cause a large thermal time constant. This kink strongly limits the fraction of flexural phonons that cross the suspended graphene edge, which causes a thermal interface resistance at its boundary. Our model predicts thermal time constants that are of the same order of magnitude as experimental data, and shows a similar dependence on the circumference. Furthermore, the model predicts the relative in-plane and out-of-plane phonon contributions to graphene's thermal expansion force, in agreement with experiments. We thus show, that in contrast to conventional thermal (Kapitza) resistance which occurs between two different materials, in 2D materials another type of thermal interface resistance can be geometrically induced in a single material.
△ Less
Submitted 25 September, 2019;
originally announced September 2019.
-
Nonequilibrium Thermodynamics of Acoustic Phonons in Suspended Graphene
Authors:
Robin J. Dolleman,
Gerard J. Verbiest,
Yaroslav M. Blanter,
Herre S. J. van der Zant,
Peter G. Steeneken
Abstract:
Recent theory has predicted large temperature differences between the in-plane (LA and TA) and out-of-plane (ZA) acoustic phonon baths in locally-heated suspended graphene. To verify these predictions, and their implications for understanding the nonequilibrium thermodynamics of 2D materials, experimental techniques are needed. Here, we present a method to determine the acoustic phonon bath temper…
▽ More
Recent theory has predicted large temperature differences between the in-plane (LA and TA) and out-of-plane (ZA) acoustic phonon baths in locally-heated suspended graphene. To verify these predictions, and their implications for understanding the nonequilibrium thermodynamics of 2D materials, experimental techniques are needed. Here, we present a method to determine the acoustic phonon bath temperatures from the frequency-dependent mechanical response of suspended graphene to a power modulated laser. The mechanical motion reveals two counteracting contributions to the thermal expansion force, that are attributed to fast positive thermal expansion by the in-plane phonons and slower negative thermal expansion by the out-of-plane phonons. The magnitude of the two forces reveals that the in-plane and flexural acoustic phonons are at very different temperatures in the steady-state, with typically observed values of the ratio $ΔT_{\mathrm{LA+TA}}/ΔT_{\mathrm{ZA}}$ between 0.2 and 3.7. These deviations from the generally used local thermal equilibrium assumption ($ΔT_{\mathrm{LA+TA}}=ΔT_{\mathrm{ZA}}$) can affect the experimental analysis of thermal properties of 2D materials.
△ Less
Submitted 25 September, 2019;
originally announced September 2019.
-
Integrated impedance bridge for absolute capacitance measurements at cryogenic temperatures and finite magnetic fields
Authors:
G. J. Verbiest,
H. Janssen,
D. Xu,
X. Ge,
M. Goldsche,
J. Sonntag,
T. Khodkov,
L. Banszerus,
N. von den Driesch,
D. Buca,
K. Watanabe,
T. Taniguchi,
C. Stampfer
Abstract:
We developed an impedance bridge that operates at cryogenic temperatures (down to 60 mK) and in perpendicular magnetic fields up to at least 12 T. This is achieved by mounting a GaAs HEMT amplifier perpendicular to a printed circuit board containing the device under test and thereby parallel to the magnetic field. The measured amplitude and phase of the output signal allows for the separation of t…
▽ More
We developed an impedance bridge that operates at cryogenic temperatures (down to 60 mK) and in perpendicular magnetic fields up to at least 12 T. This is achieved by mounting a GaAs HEMT amplifier perpendicular to a printed circuit board containing the device under test and thereby parallel to the magnetic field. The measured amplitude and phase of the output signal allows for the separation of the total impedance into an absolute capacitance and a resistance. Through a detailed noise characterization, we find that the best resolution is obtained when operating the HEMT amplifier at the highest gain. We obtained a resolution in the absolute capacitance of 6.4~aF$/\sqrt{\textrm{Hz}}$ at 77 K on a comb-drive actuator, while maintaining a small excitation amplitude of 15~$k_\text{B} T/e$. We show the magnetic field functionality of our impedance bridge by measuring the quantum Hall plateaus of a top-gated hBN/graphene/hBN heterostructure at 60~mK with a probe signal of 12.8~$k_\text{B} T/e$.
△ Less
Submitted 27 June, 2019; v1 submitted 17 January, 2019;
originally announced January 2019.
-
Fabrication of comb-drive actuators for straining nanostructured suspended graphene
Authors:
M. Goldsche,
G. J. Verbiest,
T. Khodkov,
J. Sonntag,
N. von den Driesch,
D. Buca,
C. Stampfer
Abstract:
We report on the fabrication and characterization of an optimized comb-drive actuator design for strain-dependent transport measurements on suspended graphene. We fabricate devices from highly p-doped silicon using deep reactive ion etching with a chromium mask. Crucially, we implement a gold layer to reduce the device resistance from $\approx51.6$ k$\mathrmΩ$ to $\approx236$ $\mathrmΩ$ at room te…
▽ More
We report on the fabrication and characterization of an optimized comb-drive actuator design for strain-dependent transport measurements on suspended graphene. We fabricate devices from highly p-doped silicon using deep reactive ion etching with a chromium mask. Crucially, we implement a gold layer to reduce the device resistance from $\approx51.6$ k$\mathrmΩ$ to $\approx236$ $\mathrmΩ$ at room temperature in order to allow for strain-dependent transport measurements. The graphene is integrated by mechanically transferring it directly onto the actuator using a polymethylmethacrylate membrane. Importantly, the integrated graphene can be nanostructured afterwards to optimize device functionality. The minimum feature size of the structured suspended graphene is 30 nm, which allows for interesting device concepts such as mechanically-tunable nanoconstrictions. Finally, we characterize the fabricated devices by measuring the Raman spectrum as well as the a mechanical resonance frequency of an integrated graphene sheet for different strain values.
△ Less
Submitted 7 June, 2018; v1 submitted 11 April, 2018;
originally announced April 2018.
-
Detecting Ultrasound Vibrations by Graphene Resonators
Authors:
G. J. Verbiest,
J. N. Kirchhof,
J. Sonntag,
M. Goldsche,
T. Khodkov,
C. Stampfer
Abstract:
Ultrasound detection is one of the most important nondestructive subsurface characterization tools of materials, whose goal is to laterally resolve the subsurface structure with nanometer or even atomic resolution. In recent years, graphene resonators attracted attention as loudspeaker and ultrasound radio, showing its potential to realize communication systems with air-carried ultrasound. Here we…
▽ More
Ultrasound detection is one of the most important nondestructive subsurface characterization tools of materials, whose goal is to laterally resolve the subsurface structure with nanometer or even atomic resolution. In recent years, graphene resonators attracted attention as loudspeaker and ultrasound radio, showing its potential to realize communication systems with air-carried ultrasound. Here we show a graphene resonator that detects ultrasound vibrations propagating through the substrate on which it was fabricated. We achieve ultimately a resolution of $\approx7$~pm/$\mathrm{\sqrt Hz}$ in ultrasound amplitude at frequencies up to 100~MHz. Thanks to an extremely high nonlinearity in the mechanical restoring force, the resonance frequency itself can also be used for ultrasound detection. We observe a shift of 120~kHz at a resonance frequency of 65~MHz for an induced vibration amplitude of 100~pm with a resolution of 25~pm. Remarkably, the nonlinearity also explains the generally observed asymmetry in the resonance frequency tuning of the resonator when pulled upon with an electrostatic gate. This work puts forward a sensor design that fits onto an atomic force microscope cantilever and therefore promises direct ultrasound detection at the nanoscale for nondestructive subsurface characterization.
△ Less
Submitted 22 June, 2018; v1 submitted 6 February, 2018;
originally announced February 2018.
-
Tunable mechanical coupling between driven microelectromechanical resonators
Authors:
G. J. Verbiest,
D. Xu,
M. Goldsche,
T. Khodkov,
S. Barzanjeh,
N. von den Driesch,
D. Buca,
C. Stampfer
Abstract:
We present a microelectromechanical system, in which a silicon beam is attached to a comb-drive actuator, that is used to tune the tension in the silicon beam, and thus its resonance frequency. By measuring the resonance frequencies of the system, we show that the comb-drive actuator and the silicon beam behave as two strongly coupled resonators. Interestingly, the effective coupling rate (~ 1.5 M…
▽ More
We present a microelectromechanical system, in which a silicon beam is attached to a comb-drive actuator, that is used to tune the tension in the silicon beam, and thus its resonance frequency. By measuring the resonance frequencies of the system, we show that the comb-drive actuator and the silicon beam behave as two strongly coupled resonators. Interestingly, the effective coupling rate (~ 1.5 MHz) is tunable with the comb-drive actuator (+10%) as well as with a side-gate (-10%) placed close to the silicon beam. In contrast, the effective spring constant of the system is insensitive to either of them and changes only by $\pm$ 0.5%. Finally, we show that the comb-drive actuator can be used to switch between different coupling rates with a frequency of at least 10 kHz.
△ Less
Submitted 15 July, 2016;
originally announced July 2016.
-
Interplay between nanometer-scale strain variations and externally applied strain in graphene
Authors:
G. J. Verbiest,
C. Stampfer,
S. E. Huber,
M. Andersen,
K. Reuter
Abstract:
We present a molecular modeling study analyzing nanometer-scale strain variations in graphene as a function of externally applied tensile strain. We consider two different mechanisms that could underlie nanometer-scale strain variations: static perturbations from lattice imperfections of an underlying substrate and thermal fluctuations. For both cases we observe a decrease in the out-of-plane atom…
▽ More
We present a molecular modeling study analyzing nanometer-scale strain variations in graphene as a function of externally applied tensile strain. We consider two different mechanisms that could underlie nanometer-scale strain variations: static perturbations from lattice imperfections of an underlying substrate and thermal fluctuations. For both cases we observe a decrease in the out-of-plane atomic displacements with increasing strain, which is accompanied by an increase in the in-plane displacements. Reflecting the non-linear elastic properties of graphene, both trends together yield a non-monotonic variation of the total displacements with increasing tensile strain. This variation allows to test the role of nanometer-scale strain variations in limiting the carrier mobility of high-quality graphene samples.
△ Less
Submitted 27 May, 2016; v1 submitted 11 January, 2016;
originally announced January 2016.
-
Uniformity of the pseudomagnetic field in strained graphene
Authors:
G. J. Verbiest,
S. Brinker,
C. Stampfer
Abstract:
We present a study on the uniformity of the pseudomagnetic field in graphene as a function of the relative orientation between the graphene lattice and straining directions. For this, we strained a regular micron-sized graphene hexagon by deforming it symmetrically by displacing three of its edges. By simulations, we found that the pseudomagnetic field is strongest if the strain is applied perpend…
▽ More
We present a study on the uniformity of the pseudomagnetic field in graphene as a function of the relative orientation between the graphene lattice and straining directions. For this, we strained a regular micron-sized graphene hexagon by deforming it symmetrically by displacing three of its edges. By simulations, we found that the pseudomagnetic field is strongest if the strain is applied perpendicular to the armchair direction of graphene. For a hexagon with a side length of 1 ${\rm μ}$m, the pseudomagnetic field has a maximum of 1.2 T for an applied strain of 3.5% and it is uniform (variance $< 1$%) within a circle with a diameter of $\sim 520$ nm. This diameter is on the order of the typical diameter of the laser spot in a state-of-the-art confocal Raman spectroscopy setup, which suggests that observing the pseudomagnetic field in measurements of shifted magneto-phonon resonance is feasible.
△ Less
Submitted 8 April, 2015;
originally announced April 2015.
-
Friction as Contrast Mechanism in Heterodyne Force Microscopy
Authors:
G. J. Verbiest,
T. H. Oosterkamp,
M. J. Rost
Abstract:
The nondestructive imaging of subsurface structures on the nanometer scale has been a long-standing desire in both science and industry. A few impressive images were published so far that demonstrate the general feasibility by combining ultrasound with an Atomic Force Microscope. From different excitation schemes, Heterodyne Force Microscopy seems to be the most promising candidate delivering the…
▽ More
The nondestructive imaging of subsurface structures on the nanometer scale has been a long-standing desire in both science and industry. A few impressive images were published so far that demonstrate the general feasibility by combining ultrasound with an Atomic Force Microscope. From different excitation schemes, Heterodyne Force Microscopy seems to be the most promising candidate delivering the highest contrast and resolution. However, the physical contrast mechanism is unknown, thereby preventing any quantitative analysis of samples. Here we show that friction at material boundaries within the sample is responsible for the contrast formation. This result is obtained by performing a full quantitative analysis, in which we compare our experimentally observed contrasts with simulations and calculations. Surprisingly, we can rule out all other generally believed responsible mechanisms, like Rayleigh scattering, sample (visco)elasticity, damping of the ultrasonic tip motion, and ultrasound attenuation. Our analytical description paves the way for quantitative SubSurface-AFM imaging.
△ Less
Submitted 8 February, 2016; v1 submitted 4 July, 2013;
originally announced July 2013.
-
High speed collision and reconnection of Abelian Higgs strings in the deep type-II regime
Authors:
G. J. Verbiest,
A. Achúcarro
Abstract:
We study high speed collision and reconnection of cosmic strings in the type-II regime (scalar-to-gauge mass ratios larger than one) of the Abelian Higgs model. New phenomena such as multiple reconnections and clustering of small scale structure have been observed and reported in a previous paper, as well as the fact that the previously observed loop that mediates the second intercommutation is on…
▽ More
We study high speed collision and reconnection of cosmic strings in the type-II regime (scalar-to-gauge mass ratios larger than one) of the Abelian Higgs model. New phenomena such as multiple reconnections and clustering of small scale structure have been observed and reported in a previous paper, as well as the fact that the previously observed loop that mediates the second intercommutation is only a loop for sufficiently large beta = m_scalar^2/m_gauge^2. Here we give a more detailed account of our study, involving 3D numerical simulations with beta in the range 1 to 64, the largest value simulated to date, as well as 2D simulations of vortex-antivortex (v-av) collisions to understand the possible relation to the new 3D phenomena. Our simulations give further support to the idea that Abelian Higgs strings never pass through each other, unless this is the result of a double reconnection; and that the critical velocity (v_c) for double reconnection goes down with increasing mass ratio, but energy conservation suggests a lower bound around 0.77c. We discuss the qualitative change in the intermediate state observed for large mass ratios. We relate it to a similar change in the outcome of 2D v-av collisions in the form of radiating bound states. In the deep type-II regime the angular dependence of v_c for double reconnection does not seem to conform to semi-analytic predictions based on the Nambu-Goto approximation. We model the high angle collisions reasonably well by incorporating the effect of core interactions, and the torque they produce on the approaching strings, into the Nambu-Goto description of the collision. An interesting, counterintuitive aspect is that the effective collision angle is smaller because of the torque. Our results suggest differences in network evolution and radiation output with respect to the predictions based on Nambu-Goto or beta = 1 Abelian Higgs dynamics.
△ Less
Submitted 23 June, 2011;
originally announced June 2011.
-
Higher order intercommutations in Cosmic String Collisions
Authors:
A. Achúcarro,
G. J. Verbiest
Abstract:
We report the first observation of multiple intercommutation (more than two successive reconnections) of cosmic strings at ultra-high collision speeds, and the formation of ``kink trains'' with up to four closely spaced left- or right-moving kinks. We performed a flat space numerical study of abelian Higgs cosmic string intercommutation in the type-II regime $β> 1$ (where…
▽ More
We report the first observation of multiple intercommutation (more than two successive reconnections) of cosmic strings at ultra-high collision speeds, and the formation of ``kink trains'' with up to four closely spaced left- or right-moving kinks. We performed a flat space numerical study of abelian Higgs cosmic string intercommutation in the type-II regime $β> 1$ (where $β= m^2_{scalar} / m^2_{gauge}$) up to $β= 64$, the highest value investigated to date. Our results confirm earlier claims that the minimum critical speed for double reconnection goes down with increasing $β$, from $\sim 0.98 c$ at $β= 1$ to $\sim 0.86 c$ for $β= 64$. Furthermore, we observe a qualitative change in the process leading to the second intercommutation: if $β\geq 16$ it is mediated by a loop expanding from the collision point whereas if $1 < β\leq 8 $ the previously reported ``loop'' is just an expanding blob of radiation which has no topological features and is absorbed by the strings. The multiple reconnections are observed in the loop-mediated, deep type-II regime $β\geq 16$. Triple reconnections appear to be quite generic for collision parameters on the boundary between single and double reconnection. For $β= 16$ we observe quadruple events. They result in clustering of small scale structure in the form of ``kink trains''. Our findings suggest that, due to the core interactions, the small scale structure and stochastic gravitational wave background of abelian Higgs strings in the strongly type-II regime may be quite different from what would be expected from studies of Nambu-Goto strings or of abelian Higgs strings in the $β\approx 1$ regime.
△ Less
Submitted 4 June, 2010;
originally announced June 2010.