9.

1) Calucalate and simulate the values of ID and VGS in the Following circuit
KPn = 120 VTHN = .8V VDS = 2 100 k * I D I D = VGS = VDS VDS = 2 100 k * ( ID = KPn / 2 * w / l * (V DS VTHN ) 2 ) VDS = 2 60 * V DS + 95 * V DS _ 36 .4
2

F
V KPn w * * (VGS VTHN ) 2 2 l

VDS = .934V I D = 10 .8 A

100K 2V
10/1

Circuit: *** Example 9.5 CMOS: Circuit Design, Layout, and Simulation *** DC Operating Point ... 100% vdd = 2.000000e+00 vdd#branch = -1.10055e-05 vdr = 2.000000e+00 vdr#branch = 1.100551e-05 vr = 8.994494e-01 .control destroy all run print all .endc .option scale=1u .op
VDD VDR R1 M1 VDD VDD VDR VR 0 VDR VR VR DC DC 100K 0 2 0

NMOS L=1 W=10

.MODEL NMOS NMOS LEVEL = 3 + TOX = 200E-10 NSUB = 1E17 GAMMA = 0.5 + PHI = 0.7 VTO = 0.8 DELTA = 3.0 + UO = 650 ETA = 3.0E-6 THETA = 0.1 + KP = 120E-6 VMAX = 1E5 KAPPA = 0.3 + RSH = 0 NFS = 1E12 TPG = 1 + XJ = 500E-9 LD = 100E-9 + CGDO = 200E-12 CGSO = 200E-12 CGBO = 1E-10 + CJ = 400E-6 PB = 1 MJ = 0.5 + CJSW = 300E-12 MJSW = 0.5 * .MODEL PMOS PMOS LEVEL = 3 + TOX = 200E-10 NSUB = 1E17 GAMMA = 0.6 + PHI = 0.7 VTO = -0.9 DELTA = 0.1 + UO = 250 ETA = 0 THETA = 0.1 + KP = 40E-6 VMAX = 5E4 KAPPA = 1 + RSH = 0 NFS = 1E12 TPG = -1 + XJ = 500E-9 LD = 100E-9 + CGDO = 200E-12 CGSO = 200E-12 CGBO = 1E-10 + CJ = 400E-6 PB = 1 MJ = 0.5 + CJSW = 300E-12 MJSW = 0.5 .end

Problem9.2 A MOSFET with its drain connected to gate and a current flowing through it is always in saturation. The current flowing through the MOSFET can be written as:
2 1 W * KPn * * (Vd Vthn) ..(1) Also, 2 L 2 Vd ID = ...(2) 100 K Substituting the values of KPn =120uA/V, Vthn =0.8V(from table 9.1) and W=L=10um, and equating equations (1) and (2), the following quadratic equation is obtained. 1 10 2 Vd * (120uA / V ) * * (Vd 0.8) 2 = 2 10 100 K

ID =

6Vd 2 8.6Vd + 1.84 = 0 Values of Vd = 0.2617V or 1.17V.

At Vd= 0.2617V, the MOSFET is not in saturation. Therefore Vd =1.622V.Corresponding value of ID =8.3uA (from eq. (2)). Simulated values are: Vd=1.215V and ID=7.847uA. *Circuit spice scripts. .options scale=1u . Control Destroy all Run Print all .endc *Basic circuit net list m1 d d 0 0 nmos l=10 w=10 R1 Vdd . op vdd vdd d 100k 0 DC 2

Problem 9.3:Calculate and simulate the values of ID and VSG in the following circuit (use long-channel process information given in table 9.1).

Solution:The above PMOS is gate-drain connected. It will be in saturation if VSG VTHP. KPp W 2 We know for saturation, I D = VSG VTHP 2 L 40 A 10 2 (1) ID = VSG 0.9 2 2 V 1 (5 VSG ) (2) Also by KVL, I D = 100k (5 VSG ) 40 A 10 2 = VSG 0.9 Equating (1) and (2), 2 100k 2 V 2 By solving the above quadratic equation, we get two values for VSG (1.33V or 0 .42v). As the MOSFET is in saturation region, current ID flows in the circuit if VSG VTHP. Therefore, VSG = 1.33v & I D = 36.7A

b b

Spice Netlist:**Problem#9.3 .control destroy all run print all .endc .option scale=1u .op VDD VDD 0 R1 M1 VD VD 0 VD

DC 100K VDD

VDD

PMOS L=1 W=10

Simulation Results:DC Operating Point ... 100% vd = 3.713491e+00 vdd = 5.000000e+00 vdd#branch = -3.71349e-05 Vsg = 1.286509e+00

vds -1.2865 vbs 0. vth -834.8123m vdsat -345.5119m beta 396.4747u gam eff 521.2973m gm 147.9632u gds 2.3812u gmb 0. cdtot 2.0237f cgtot 13.4667f cstot 11.2084f cbtot 234.5729a cgs 11.2084f cgd 2.0237f

Problem 9.04

Since the above figure is a gate drain connected mosfet and current is flowing its operating in saturation region. Using KVL 5-ID.100k =VSG 5-KPP.W/2L.(VSG-VTHP)2 . 100K =VSG ;where KPP=40uA/V2, VTHP=0.9V solving for VSG we have VSG =2.1v and 0.8v,since mosfet is in saturation therefore VSG=2.1v ID= KPP.W/2L.(VSG-VTHP)2 Solving for ID with VSG=2.1v results in ID =28.8uA
Spice simulations
**Problem 9.04 .control destroy all run let vsg=vdd-vd1 print vd1 print vsg print mag(vdd#branch) .endc .option scale=1u M1 vd1 vd1 vdd vdd PMOS W=10 L=10 Vdd vdd 0 DC 5 R1 vd1 0 100k *.dc Vdd 0 5 1m .op

Results: DC Operating Point ... 100% vd1 = 2.732722e+00 vsg = 2.267278e+00 mag(vdd#branch) = 2.732722e-05

Problem 9.5:Calculate ID , VDS , and estimate the small-signal resistance looking into the drain of the MOSFET in the following circuit.

LMb3 0.8gV V I = 120 2 V 2 N b5 V g (2) But, I = 200k b5 V g = 120 A 10 MLb3 0.8gV From (1) and (2), V 2 N 200k
A 10
2 2 DS D DS

Solution:From the above figure, the gate overdrive voltage is high and the resistor value is also large. It is a good indication that the transistor may be in triode (because even if a small current flows in the circuit, the voltage drop across the resistor is high). So lets start with the assumption that the MOSFET is in triode. W V 2 I D = KPn VGS VTHN VDS DS 2 L

MNLb

PQO OP (1) Q

DS

DS

DS

VDS 2 . 2

POQ

By solving the above quadratic equation, we get two values for VDS (4.39V or 19mv). As the MOSFET is in triode region, VDS = 19mv and I D = 24.9 A .

As the MOSFET is in triode region, the small signal resistance looking into the drain of the MOSFET will be its channel resistance. 1 Rch W VGS VTHN KPn L R ch = 757.5

9.5 & 9.6 Simulations 9.5) DC operating conditions

DC Operating Point ... 100% VDS=d1 = 2.091701e-02 g1 = 3.000000e+00 vdd = 5.000000e+00 ID= ABS(vdd#branch) = 2.48954e-05 vg1#branch = 0.000000e+00 vt = 0.000000e+00 vt#branch = 0.000000e+00 9.6) Small signal resistance looking into the drain

RCh =846 Ohms from simulations.

* SPICE command scripts .control destroy all run print all * plot VD1#branch .endc

Vdd Vdd 0 DC 5.0 * ====================================== M11 d1 g1 0 0 nmos W=10 L=2 R1 d1 Vdd 200k Cbig d1 Vt 1 Vt Vt 0 DC 0 AC 1m VG1 g1 0 DC 3.0

* ====================================== * .AC DEC 10 1 10K .options scale=1u * ABSTOL=1u VNTOL=1mv RELTOL=0.01 .op

* Level 3 models * * 1 um models created by RJB. These models are for educational purposes only! They are *not* * extracted from actual silicon. * * Don't forget the .options scale=1u if using an Lmin of 1 * 1<Ldrawn<200 10<Wdrawn<10000 Vdd=5V .MODEL NMOS NMOS LEVEL = 3 + TOX = 200E-10 NSUB = 1E17 GAMMA = 0.5 + PHI = 0.7 VTO = 0.8 DELTA = 3.0 + UO = 650 ETA = 3.0E-6 THETA = 0.1 + KP = 120E-6 VMAX = 1E5 KAPPA = 0.3 + RSH = 0 NFS = 1E12 TPG = 1

+ XJ = 500E-9 LD = 100E-9 + CGDO = 200E-12 CGSO = 200E-12 CGBO = 1E-10 + CJ = 400E-6 PB = 1 MJ = 0.5 + CJSW = 300E-12 MJSW = 0.5 * .MODEL PMOS PMOS LEVEL = 3 + TOX = 200E-10 NSUB = 1E17 GAMMA = 0.6 + PHI = 0.7 VTO = -0.9 DELTA = 0.1 + UO = 250 ETA = 0 THETA = 0.1 + KP = 40E-6 VMAX = 5E4 KAPPA = 1 + RSH = 0 NFS = 1E12 TPG = -1 + XJ = 500E-9 LD = 100E-9 + CGDO = 200E-12 CGSO = 200E-12 CGBO = 1E-10 + CJ = 400E-6 PB = 1 MJ = 0.5 + CJSW = 300E-12 MJSW = 0.5 .end

Problem 9.6

To determine the small signal resistance we can run an AC analysis in spice and then plot the ratio of the drain voltage divided by the current through the 10mV AC source vt. We sweep the frequency from 10Hz to 1MHz. The netlist for this circuit is shown below. Problem 9.6 .opt scale=1u .control destroy all run plot test/I(Vt) plot I(Vt) plot I(Vin) .endc .ac DEC 10 100 1MEG Vin in 0 DC=5 Vg gate 0 DC=3 Vt test 0 DC=0 AC=10m C1 drain test 1 R1 in drain 200k M1 drain gate 00 nmos L=2.00 W=10.00 .include C:\ 1u_models.txt The first plot is of the vd/id and is shown in the plot below.

Looking at the plot we can see that the small signal resistance is 847 . To determine how the 200k resistor effects the circuit, we can see that the 200k resistor is in parallel with the small signal resistance when we do AC analysis.

Lets look at how much current is flowing through the capacitor branch. This is shown in the plot below.

There is about 11.8 uA flowing through the capacitor. Now lets look at how much current is flowing through the 200k branch

There is about 50nA flowing through the 200k resistor. The current through the 200k resistor is much smaller than the current flowing through the capacitor. Thus we can neglect the effect of the 200k resistor to the current through the capacitor.

Problem #9.7

Figure 9.42 When Ibias is increased, VS3 and VGS3 increase. When VGS3 is increased, VGS4 also increases because their gates are tied together. When VGS increases, the Drain to Source Voltage decreases, as illustrated below in Figure 9.42.A. Therefore VDS4 decreases.

ID VGS2 VGS1

VDS

Ibias2 Figure 9.42.A.

Ibias1

9.8.) Describe qualitatively what happens if we steal or inject current at the point indicated in Fig 9.43. How does this affect the operation of M1 and M2? Verify your answer with SPICE. (See Fig 9.43 for circuit schematic). Solution (by Robert J. Hanson, CNS): We will use a long channel model for this problem. Since the gates of M2 and M4 are tied together and the sources of M2 and M4 are tied together, VSG2=VSG4. Additionally, since we will assume a current of 1A for Ibias at the drain of M1, that current must flow through both M1 and M2, as well as M4 and M3. Hence VSD2=VSG2=VSG4=VSD4 and VSD1=VSG1=VSG3 since all the PMOS devices are assumed to be sized the same (we will assume W/L=30/2 for the simulations). When current is stolen from the drain of M4, it causes the drain voltage node (here called VD4M, which is also the source voltage of M3, VS3) to decrease which results in a decreased VSD3 (i.e. M3 begins to lose its ability to pass current, VSG3 also goes down). If 1 A of current is stolen, M3 completely shuts off and all of the 1 A flows through M4 on that side of the circuit. (Note that the x-coordinate should be labeled in units of A as it is a sweep of -1A of injected current to +1A of injected current).

In the plot below VSG3 decreases due to VS3 decreasing when current is stolen from the node at VD4M.

VSD3 is actually the same as VD4M since VSD3=VS3-VD3=VS3-0=VD4M

Conversely, if current is injected into the node mentioned above, it will cause the voltage VD4M to increase to the point where the current flowing through M3 will be 2A when the injected current has reached 1A (1A provided by Iinject and 1A by M4).

The simulation results below show what happens to VSG1 and VSG2 due to Iinject, note that they do not change.

Similar results are obtained for VSD1 and VSD2, since current and VSG is constant, VSD must also be constant.

The SPICE NetList for this simulation is provided below with the Long Channel Simulation Model that was used:
*** Problem 9.8 Solution *** .control destroy all run let VSG1=VG2-VG1 let VSG2=VDD-VG2 let VSG3=VD4M-VG1 let VSG4=VDD-VG2 let VSD1=VG2-VG1 let VSD2=VDD-VG2 let VSD3=VD4M-V3S let VSD4=VDD-VD4 plot vmeas#branch plot v3test#branch plot VD4M plot VSG1 plot VSG2 plot VSG3 plot VSG4 plot VSD1 plot VSD2 plot VSD3 plot VSD4 plot VG1

plot VG2 *print all .endc .option scale=1u *.OP .dc Iinject -1uA VDD VDD Ibias VG1 Iinject 0 VMEAS VD4 VTEST2 V3TEST M1 M2 M3 M4 VG1 VG2 V3S VD4 0 0 VD4M VD4M VG2 V3S VG1 VG2 VG1 VG2

1uA DC DC DC DC VG2M 0 VG2M VDD VD4M VDD

10nA 5 1u 1u 0 DC DC VDD VDD VDD VDD

0 0 PMOS L=2 W=30 PMOS L=2 W=30 PMOS L=2 W=30 PMOS L=2 W=30

.MODEL NMOS NMOS LEVEL = 3 + TOX = 200E-10 NSUB = 1E17 GAMMA = 0.5 + PHI = 0.7 VTO = 0.8 DELTA = 3.0 + UO = 650 ETA = 3.0E-6 THETA = 0.1 + KP = 120E-6 VMAX = 1E5 KAPPA = 0.3 + RSH = 0 NFS = 1E12 TPG = 1 + XJ = 500E-9 LD = 100E-9 + CGDO = 200E-12 CGSO = 200E-12 CGBO = 1E-10 + CJ = 400E-6 PB = 1 MJ = 0.5 + CJSW = 300E-12 MJSW = 0.5 * .MODEL PMOS PMOS LEVEL = 3 + TOX = 200E-10 NSUB = 1E17 GAMMA = 0.6 + PHI = 0.7 VTO = -0.9 DELTA = 0.1 + UO = 250 ETA = 0 THETA = 0.1 + KP = 40E-6 VMAX = 5E4 KAPPA = 1 + RSH = 0 NFS = 1E12 TPG = -1 + XJ = 500E-9 LD = 100E-9 + CGDO = 200E-12 CGSO = 200E-12 CGBO = 1E-10 + CJ = 400E-6 PB = 1 MJ = 0.5 + CJSW = 300E-12 MJSW = 0.5 .end

Problem 9.9:Using simulations, generate the plot seen in Fig. 9.12 for both NMOS and PMOS devices.
Solution:-

For the MOSFETs shown in the above figure, a current source of 1uA is connected at the drain so that the gate overdrive voltage is less. (Then VGS or VSG will be almost equal to the threshold voltage. The plots below show the variation of the threshold voltage with respect to the variation of source to bulk potential for both NMOS and PMOS devices.

Spice Netlists:***NMOS .control destroy all run plot VGS .endc .option scale=1u .dc VSB 0 5 .01

***PMOS .control destroy all run let VSG=VDD-VG plot VSG .endc .option scale=1u .dc VBS 0 5 .01

VDD VDD 0 VSB 0 VSB IBIASP VDD VGS

DC DC DC

5 0 1u

M1 VGS VGS 0 VSB NMOS L=1 W=10

VDD VDD 0 DC 5 VBS VBS VDD DC 0 IBIASP VG 0 DC 1u M1 VG VG VDD VBS PMOS L=1 W=10

9.10) Design a circuit that will linearly convert an input voltage that ranges from 0 to
4V into a current that ranges from roughly 50A to 0. Simulate the operation of the design showing the linearity of the voltage to current conversion. How does the MOSFETs length affect the linearity?

Solution: For voltage to current conversion we use an inactive, (resistor tied to the source) source follower. With this configuration the source of our PMOS transistor is not held to a fixed voltage so to reduce the source to body potential difference we tie the body of the transistor to the source of the PMOS.

For a quick sizing of the resistor we assume that our Vthp, transistor must stay in the saturation region, is approximately 1V which gives us a resistor value of 80k if we are to source 50A. For the sizing of the PMOS lets start with the values in the book and run a simulation to see what our linearity is. We will plot the ID vs VSG and the derivative of ID to see the linearity. W=30 L=2

From the ID plot we see that we are almost at 50uA with the 80k resistor, a value of 74k would have got us to 50uA but well leave the 80k for comparison as we change the

sizing of the PMOS to improve linearity. From the plot of the slope of ID we see that we have a variation of around 24%. To improve the voltage to current linearity well push out the point at which the PMOS starts to enter the subthreshold region, we want to keep the PMOS in the saturation or linear region as long as possible. We do this by increasing our W and decreasing our L.

We can clearly see from the log of ID plot that the linearity is almost ideal until around 3.5V, where the MOSFET starts to turn off and enter the subthreshold region. Plotting the voltage at the source of the PMOS confirms this at the swept gate voltage of 3.5V the source voltage is around 4.4V which is right at the expected point where the PMOS enters the subthreshold region.

Problem 9.11:Using a PMOS device, discuss and show with simulations how it can be used to implement a 10k resistor. Are there any limitations to the voltage across the PMOS resistor? Explain.
Solution:-

Fig: - PMOS with VSG=5V and VD>VTHP

The MOSFET looks like a resistor when we are using in a triode region. The equation for the channel resistance is given as below 1 . If VSG VTHP >>VSD , this equation can be written as, Rch = W VSG VTHP VSD KPp L 1 . Use VSG =5V so that the bias is fixed and also gives a Rch W VSG VTHP KPp L maximum range of VSD,sat. Given Rch=10K. 1 W Rch = = 10k = 0.61. If L=10, then W=61. A W L 40 2 5 0.9 V L Limitations: - One end of the resistor should be VDD and the other end should be VD>VTHP. Though we VD>VTHP, the simulation shows that VD>2.5V for better linearity of the resistor.

Simulation:.control destroy all run plot VD#branch .endc .option scale=1u .dc VD 0 5 .1 VDD VDD 0 DC 5 VD VD 0 DC 0 M1 VD 0 VDD VDD PMOS L=10 W=61

Chapter 9: CMOS Circuit Design, Layout, and Simulation Problem 9.12 Using SPICE (and ensuring the MOSFET is operating in the saturation region with sufficient VDS) generate the iD vs. vGS curve seen in Fig 9.15. Using SPICE take the derivative of iD to plot the devices gm (versus VGS). How does the result compare to Eq. 9.22? Does the level 3 model used in the simulation show a continuous change form sub-threshold to strong inversion? Solution: The first step to completing this task is to create a netlist that enables will allow us to supply a specific VDS to the part and allow us to vary VGS. VGS will be our main x-axis variable because gm is defined as the derivate of ID with respect to VGS. Therefore, in our netlist we will supply a constant VDS and using a DC sweep vary VGS. VDS should be well above VDS,sat so we will arbitrarily choose 250mV. The .DC statement varies VGS from 0 to 2.5V in 10mV increments. Netlist
.control destroy all run *** DC Analysis *** let ID=-VDS#branch let gm=deriv(ID) let gmcalc=(120E-6*(10/2)*(VGS-0.8)) plot ID gm gmcalc *plot gm .endc .option scale=1u .DC VGS 0 VDS VGS M1 VDS VGS VDS 0 0 VGS

2.5 DC DC 0

10m 250m 0 0 =3 NSUB VTO ETA VMAX NFS LD CGSO PB MJSW

AC 1 NMOS L=2 W=10

.MODEL NMOS NMOS LEVEL + TOX = 200E-10 + PHI = 0.7 + UO = 650 + KP = 120E-6 + RSH = 0 + XJ = 500E-9 + CGDO = 200E-12 + CJ = 400E-6 + CJSW = 300E-12 .end

= 1E17 = 0.8 = 3.0E-6 = 1E5 = 1E12 = 100E-9 = 200E-12 =1 = 0.5

GAMMA = 0.5 DELTA = 3.0 THETA = 0.1 KAPPA = 0.3 TPG = 1 CGBO = 1E-10 MJ = 0.5

Chapter 9: CMOS Circuit Design, Layout, and Simulation Next, three definitions are issued with let statements to define ID, gm, and calculated gm. gm,calc is merely equation 9.22 using the parameters from the level 3 NMOS model for n and VTHN. Figure 1 shows the results when this netlist is run. The red line is ID. ID behaves as expected because there is almost no current until VGS > VTHN (~0.8V) and then there is a rapid increase in the ID for an increase in VGS. The green line is gm and also behaves as expected. gm is defined as the rate of change of id with respect to vgs. This definition is only value for the area of the ID vs VGS curve around the VGS bias point. For this particular case the VGS is approximately 1.05V. The blue line is the calculated value of gm. It is obvious that the calculated value of gm correlated very well with the simulated version for the immediate region surrounding the VGS bias point.

Figure 1. ID, gm, and gm,calc vs. VGS

Chapter 9: CMOS Circuit Design, Layout, and Simulation This model shows a very continuous change from the subthreshold to the strong inversion regions. This can be seen in Figure 2 by observing ID and gm with no discontinuities below for VGS < VTHN.

Figure 2. Zoomed in version of Figure 1. to show the subthreshold region

9.13)
VDD VDD=5V

1.3V M1 21/3 1mv id

To find weather the MOSFET is in saturation or triode we need to check the following two conditions VSG > VTHP => 1.3V > 0.9V VSD > VSG VTHP => 5V > 1.3V 0.9V. (Were VSG= 1.3 V; VTHP= 0.9V) As both the conditions are satisfied the MOSFET is in Saturation. The relation between the AC gate voltage to the AC drain current is given by id = gm x vgs. And the value of gm is given by gm = Kpp x W/L (VSG VTHP) gm = 40A/V x 21/3 x (1.3-0.9) = 112 A/V. id = gm x vgs = 112 A/V x 1mV = 112 nA. The AC drain current id = 112 nA Sin2f. And ID = Kpp/2 x W/L (VSG VTHP)2 = 40/2 x 21/3 x (1.3-0.9)2 = 22.4 A.

SPICE SIMULATIONS 1.A) AC Simulations Source Code : *** Problem 9.13 CMOS: Circuit Design, Layout, and Simulation *** * AC ANALYSIS .control destroy all run plot -VDD#BRANCH .endc

.option scale=1u .ac dec 100 1 10k VDD VDD 0 VG1 VDD VG1 M1 0 VG1 Simulation result:

DC 5 DC 1.3 AC 1m SIN 2.5 1m VDD VDD PMOS L=3 W=21

Simulation Result: id = 97 nA. ( Hand Calculation : id = 112 nA). 1.B) The Transient Analysis Source Code *** Problem 9.13 CMOS: Circuit Design, Layout, and Simulation *** * The Transient Analysis .control destroy all run .endc .option scale=1u .op VDD VDD 0 VG1 VDD VG1 M1 0 VG1 DC 5 DC 1.3 AC 1m SIN 2.5 1m VDD VDD PMOS L=3 W=21

Result of Simulation : ID = 2.1 x 10^-5 = 21 A. ( Hand Calculation ID = 22.4 A) Overall Result:The Spice Simulations and Hand Calculations are close.

Problem: 9.14 The gates and sources of both M1 and M2 are both physically connected VGS1=VGs2 and ID1=ID2=20uA Assuming both M1 and M2 are operating in saturation VGS1=VGs2= =

2 ID. L

KPn.W

+ Vthn

2.20.2 + 0.8 =1.06v 120.10

VGS1=VG-Vs1 therefore Vs1= VG- VGS1=2.5-1.06=1.44v Since VG and gate source voltages of both mosfets (M1 and M2) are same the source voltages are also same. Assuming M3 and M4 are in triode: The source to gate voltage for M3 and M4 is ID3=KPp.W/L.[(VSG-Vthn).VSD- VSD2/2)] 20=40*10-6.30/2.[(5-0-0.9). VSD- VSD2/2)] solving the above quadratic equation we get VSD=8.19v and 0.00813v. The former value is not a valid value as the source voltage applied is only 5V. So taking the latter value VD3=Vs3-VSD3=4.991V As the gate to source voltage of M3 and M4 are same and same ID flows VSD3= VSD4 thus VD3 = VD4=4.991V Now let us verify whether are assumptions are right or not Consider M3 VSG3=5-0=5V and VSD3=0.00813V therefore VSG3>Vthn and VSD3<VSG3-Vthp thus our assumption that M3 is triode is correct. Consider M1 VGS1=2.4-1.44=1.06V and VDS1=4.967V therefore VGS1> Vthn and VDS1> VGS1- Vthn thus our assumption is correct. Similarly M2 and M4 are operating in saturation and triode regions respectively. M3 and M4 can be modeled as resistors whose resistance is channel resistance as they are operating in triode RCHM4= RCHM3=[KPp

W -1 .[VSG4-Vthp]] =406.50 ohms. L

AC analysis We start by writing loop equation 1mv-vgs1+vgs2+1mv=0 => vgs1-vgs2=-2mv

id 1 id 2 = 2mv gm1 gm 2
since id1=-id2=id3=-id4 and gm1=gm2 vgs1=- vgs2=1mv id1= gm1. vgs1=150nA Ac drain voltages of M2 and M4= - id4. RCHM4=60.9uV AC drain voltage of M1 and M3=- id1. RCHM1=150nA. 406.5=60.9uV iD1=20u+0.15sin2f iD2=20u-0.15sin2f

DC analysis

AC analysis

AC currents Verification using Spice: *** problem 9.14 .control destroy all run ** for the operating point analysis *print all * for the AC analysis plot mag(vd13) mag(vs12) mag(vg1) .endc .option scale=1u *.op .ac dec 100 1 10k VDD VDD 0 DC 5 VG1 VG2 Ibias M1 M2 M3 M4 VG1 VG2 VS12 VD13 VD24 VD13 VD24 0 0 0 VG1 VG2 0 0 DC Dc DC VS12 VS12 VDD VDD

From simulations id1=-id2=143.86nA

2.5 AC 1m SIN 2.5 1m 10k 2.5 AC -1m SIN 2.5 1m 10k 40u 0 NMOS L=2 W=10 0 NMOS L=2 W=10 VDD PMOS L=2 W=30 VDD PMOS L=2 W=30

DC Operating Point vd13 = 4.989699e+00 vd24 = 4.989699e+00 vdd = 5.000000e+00 vdd#branch = -4.00000e-05 vg1 = 2.500000e+00 vg1#branch = 0.000000e+00 vg2 = 2.500000e+00 vg2#branch = 0.000000e+00 vs12 = 1.171839e+00 AC voltages
. from simulations mag(vd13)=74.2uV,Vg1=1mv The hand calculated values and simulations results are almost close

9.15 To calculate the AC, DC voltages and currents in the circuit below: To find the operating points of the circuit do the DC analysis. Hence short all the AC voltage sources. DC Analysis: The DC equivalent of the given problem is given below: Assume both M1 and M2 are in saturation, we will verify our assumption shortly. Since the sources of both M1 and M2 are tied together and gates are connected to 2.5V VGS1=VGS2 and since the circuit is symmetric ID1=ID2=10uA VGS1 or VGs2 =

2 IL + Vthn KPnW

2.10.2 + 0.8 = 0.9825V 120.10

It follows that VS1= VS2 = VG - 0.9825 2.5 - 0.9825 =1.517V DC equivalent circuit

Coming to M3 and M4, since both the gates are tied to ground and source is at VDD by intuition they might be in triode. We will verify this too shortly. In triode: ID = KPp.W/L. [(VSG-Vthp).VSD3- (VSD3)2 /2)]

Since ID = 10 A and other parameters are known except VSD3, solve for VSD3

10 = 40.

30 Vsd 2 ((5 0.9)Vsd ) 2 2

Solving for VSD3 we get VSD3 = 0.00406 V or 8.195 V. The later value for VSD3 doesnot make any sense.

VD3 = 5 -VSD3=4.995V

From the circuit it can be seen that VD3 = VD4 . Now for M1: VDS = 4.995 1.517 = 3.478 V VGS -Vthn = 0.9825 - 0.80 = 0.1825 V Since VDS > VGS - Vthn ,our assumption that M1 is in saturation is correct.

Now for M3: VSD = 5 - 4.995 = 5mV VSG -Vthp = 5 - 0.90 = 4.1V Since VSD < VSG - Vthp ,our assumption that M3 is in triode is verified. Similar argument follows for M2 and M4. Since M3 and M4 are in triode they behave as a resistors whose resistance is given by: RCHM4= RCHM3 = VSD/ID = 0.00406/10uA = 406 The transconductance of M1 and M2 are given by: gm1 = gm1 =

KPn

W (Vgs Vthn ) L

= 120.10/2(0.9825-0.8) = 109.5 A/V Having calculated all the DC parameters lets check our calculations with simulations: SPICE result = vd13 = vd24 = 4.994858e+00 SPICE result = vs12 = 1.239740e+00 Hand calculation gave us 4.995 V Hand calculation gave us 1.517V

The discrepancy in vs12 is because of the fact that we did not take body effect into account. Now coming to the AC analysis: AC Analysis: The AC equivalent circuit is shown: By KVL: 1mV = vgs1 - vgs2 -1mV vgs1-vgs2=2mV and since

id = vgs it follows gm id 1 id 2 = 2mV gm1 gm 2

and we know that id1= -id2 = id3= -id4 and gm1=gm2 Therefore it follows that vgs1= -vgs2 = 1mV Calculating the AC drain current AC equivalent circuit id1= gm1. vgs1=109.5 A/V*1mV = 109.5nA Therefore the total instantaneous current is given by iD1 = 10u+0.1095sin2f iD2 = 10u-0.1095sin2f where f is the frequency of the AC source.

Now calculating the AC voltages: AC drain voltage of M1 or M3 = -id1. RCHM1 = 109.5nA X 406 = 0.044mV AC drain voltage of M2 and M4= id4. RCHM4 = 109.5nA X 406 = 0.044mV Lets check our hand calculations with simulated results: Simulated drain voltage = 0.054mV Both the values are pretty close. Hand calculated = 0.044mV.

The SPICE net lists and plots are shown in below: AC input voltage

Drain voltages of M1,M2,M3,M4 SPICE NETLIST: .control destroy all run ** for the operating point analysis *print all * ** for the AC analysis plot mag(vd13) mag(vg1) .endc .option scale=1u *.op .ac dec 100 1 10k VDD VG1 VG2 Ibias M1 M2 M3 M4 .end VDD VG1 VG2 VS12 VD13 VD24 VD13 VD24 0 0 0 0 VG1 VG2 0 0 DC DC DC DC VS12 VS12 VDD VDD 5 2.5 2.5 20u 0 0 VDD VDD AC 1m AC -1m SIN 2.5 1m 10k SIN 2.5 1m 10k

NMOS L=2 W=10 NMOS L=2 W=10 PMOS L=2 W=30 PMOS L=2 W=30

9.16 The drain currents calculated in Ex. 9.5 are

iD1 = 20uA + 0.075sin 2 f iD2 = 20uA 0.075 sin 2 f

Spice Netlist
*Prob 9.16* .control destroy all run * for the AC analysis * plot v1#branch v2#branch **For transient analysis **plot v1#branch **plot v2#branch .endc .option scale=1u *.ac dec 100 1 10k **.tran 1u 300u v1 v2 vdd vg1 vg2 ibias M1 M2 M3 M4 vd13 va1 0v vd24 va2 0v vdd 0 dc vg1 0 dc vg2 0 dc vs12 0 dc va1 va2 vd13 vd24 vg1 vg2 vd13 0 vs12 vs12 vdd vdd

5 2.5 2.5 40u 0 0 vdd vdd

ac

1m

sin 2.5 1m 10k

NMOS L=2 W=10 NMOS L=2 W=10 PMOS L=2 W=30 PMOS L=2 W=30

*Level 3 models .MODEL NMOS NMOS LEVEL = 3

----------------------------.MODEL PMOS PMOS LEVEL = 3 -------------------------------.end

AC Analysis

V1#branch = 72nA, V2#branch = -72nA Transient Analysis

Problem 9.17
When the potential of the source of a MOSFET is increasing, a point is reached where the gate to source potential goes below the threshold voltage. The MOSFET then shuts off. Thats the point where the graph cuts the x-axis. When the source voltage (or the source to bulk potential, since the body is grounded) is 0, the value of ID is where the graph cuts the y-axis.

SPICE Netlist:
*** PROBLEM 9.17 CMOS: Circuit Design, Layout, and Simulation *** .control destroy all run LET ID = -VMETER#branch PLOT ID .endc .option scale=1u .DC VDD VG VSB M1 VSB VDD VG VSB VD 0 0 0 0 VG VD 5 DC DC DC VSB VDD 100m 5 5 5 0 DC

AC

1m

NMOS L=2 W=10 0

VMETER

.MODEL NMOS NMOS LEVEL = 3 + TOX = 200E-10 NSUB = 1E17 GAMMA = 0.5 + PHI = 0.7 VTO = 0.8 DELTA = 3.0 + UO = 650 ETA = 3.0E-6 THETA = 0.1 + KP = 120E-6 VMAX = 1E5 KAPPA = 0.3 + RSH = 0 NFS = 1E12 TPG = 1 + XJ = 500E-9 LD = 100E-9 + CGDO = 200E-12 CGSO = 200E-12 CGBO = 1E-10 + CJ = 400E-6 PB = 1 MJ = 0.5 + CJSW = 300E-12 MJSW = 0.5 * .MODEL PMOS PMOS LEVEL = 3 + TOX = 200E-10 NSUB = 1E17 GAMMA = 0.6 + PHI = 0.7 VTO = -0.9 DELTA = 0.1 + UO = 250 ETA = 0 THETA = 0.1 + KP = 40E-6 VMAX = 5E4 KAPPA = 1 + RSH = 0 NFS = 1E12 TPG = -1 + XJ = 500E-9 LD = 100E-9 + CGDO = 200E-12 CGSO = 200E-12 CGBO = 1E-10 + CJ = 400E-6 PB = 1 MJ = 0.5 + CJSW = 300E-12 MJSW = 0.5 .end

Problem 9.18 For n-MOSFET W/L=100/20, p-MOSFET W/L=300/20

ID =

KPn W . .(VGS VTHP )2 2 L

when W and L are both multiplied by 10 as seen in the equation the drain current does not change.

VSG =

2I D L . +VTHP = KPP W

2.20 20 +0.9 = 1.158 V . 40 300

The VGS (NMOS) & VSG (PMOS) of the MOSFETs are 1.058 V and 1.158 V respectively they remain the same as in Ex. 9.5 as the drain current (roughly 20 bias current) is almost the same. Both the MOSFETs have a VDS.SAT of 250mV Figure shows the IV plots and the output resistance (the reciprocal of the derivative of the drain current) for the MOSFETs. The output resistances (from the plots) of NMOS & PMOS are 500 MEG & 300 MEG respectively as against 5 MEG & 4 MEG in Ex.9.6. As Since L increases by 10 the output resistance increased by a factor of 100 and decreases. The channel-length modulation parameter is calculated as follows: n= 1/ IDS,SAT.r0= 1/ (20 .500MEG) = .0001V-1

1/L, r0 L2/V2 DS,SAT

p= 1/ IDS,SAT.r0= 1/ (20 .300MEG)

= .00016V

-1

VDD VGN M1 VGN=1.05 V 100/20

let ro=1/deriv(ID) plot ro .endc .option scale=1u .dc VDD 0 5 1m VDD VDD 0 VGN VGN 0 M1 VDD VGN

DC DC 0

5 1.05 0 NMOS L=20 W=100

PMOS .control destroy all run let ID=-VDD#branch plot ID let ro=1/deriv(ID) plot ro .endc .option scale=1u .dc VDD 0 5 1m VDD VGP M1 VDD VDD 0 0 VGP VGP DC DC VDD 5 1.15 VDD

VGP M1 VGP=1.158V 300/20

PMOS L=20 W=300

NMOS

NMOS

PMOS

PMOS

Problem 9.19 From the equation 9.36 we have, ft= gm / (2 Cgs) where Cgs= (2/3) W L Cox and substituting we get

gm= KPn (W/L)(Vgs-Vth)

ft=[3 KPn (Vgs-Vth)] / [ 4 L2 Cox] so ft1= [3 KPn (Vgs-Vth)] / [ 4 L12 Cox] and ft2= [3 KPn (Vgs-Vth)] / [ 4 L22 Cox] ft1/ft2=( L2 /L1)2 For our case comparing 10/2 NMOS to 100/20 NMOS we get ft1/ft2=( 20 /2 )2 = 100 ft2 = ft1/100 From this relationship we can see that ft depends only on channel length. In other words ft decreases with channel length increase (quadratic dependence on channel length relationships). To illustrate change, WinSpice simulations were performed and obtained following graphs:

Figure 1: Simulation ft1 Plot for 10/2 NMOS

Figure 2: Simulation ft2 Plot for 100/20 NMOS From figures 1 and 2 we can see that ft1 = 2 x 109 Hz (ft1 intersect 0-axes) and ft2 = 2 x 107 Hz (ft2 intersect 0-axes) approximately. So, ft1/ft2 = 100 approximately

Problem 9.20 Yes, it is possible to have sub threshold operation when drain current is 100uA.Simply use a larger
W/L device .This scales currents in all regions (sub threshold, triode and saturation) to go up by a factor of W/L.

Problem 9.21 This problem asks us to estimate the threshold voltage of a PMOS and a NMOS transistor which are fabricated using a short channel process. The dimensions of both MOSFETS are 50/5. We will start with the NMOS. The threshold voltage may be estimated by examining two different plots. First, if we plot ID versus VGS, the threshold voltage may be estimated by linearly extrapolating back to the x-axis. As seen in figure 1, the extrapolation yields an approximate value of 280mV for VTHN.

Figure 1: ID verses VGS, showing the Threshold Voltage at ~280mV The second method of threshold estimation involves plotting the derivative of ID versus VGS. Once again, we will linearly extrapolate back to the x-axis to find the approximate value of VTHN. Figure 2 shows that the threshold voltage is approximately 210mV. This measurement is considered more accurate than the first. For more explanation, please see Figure 9.27 and the accompanying paragraph in chapter 9 of the text. The netlist used to generate these figures is shown in Figure 3.

Figure 2: The Derivative of ID (gm) verses VGS, showing the Threshold Voltage at ~210mV

*** Problem 9.21, from Figure 9.27 CMOS: Circuit Design, Layout, and Simulation *** .control destroy all run let ID=-VDS#branch let gm=deriv(ID) plot gm plot ID .endc .option scale=50n .DC VGS 0 VDS VGS M1 VDS VGS 0 0

1 DC DC

1m .1 0

VDS VGS 0 0 NMOS L=5 W=50 Figure 3: Netlist used to generate Figures 1 & 2 (MOSFET models are omitted.)

The situation is the same for the PMOS. Figure 4 shows that VTHP is about 250mV. Figure 5 shows the VTHP is about 190mV. Finally the netlist used for the PMOS simulations is shown in figure 6.

Figure 4: ID verses VSG, showing the Threshold Voltage at 250mV

Figure 5: The Derivative of ID (gm) verses VSG, showing the Threshold Voltage at ~190mV

*** Problem 9.21, from Figure 9.27 (PMOS) CMOS: Circuit Design, Layout, and Simulation ** .control destroy all run let ID=-VSD#branch let gm=deriv(ID) plot gm plot ID .endc .option scale=50n .DC VSG 0 VSD 0 VSG 0 M1

1m .1 0

VSD DC VSG DC

VSD VSG 0 0 PMOS L=5 W=50 Figure 6: Netlist used to generate Figures 4 & 5 (MOSFET models are omitted.)

Problem 9.22:Show the details leading to Eq. (9.43). Show, as an example, that the approximation is ' valid if Q bo ' = 30mv . (Remember: temperature is in Kelvin.) C ox Solution:From chapter 6, Eq.(6.17), Q ' bo Q ' ss , where Q ' ss is a constant. VTHN = Vms 2V fp + C ' ox kT N D , poly kT N A Q ' bo = 2qN A si / 2V fp / , V fp = ln and Vms = ln V fp q ni q ni

VTHN = VTHN

kT N D , poly Q ' bo Q ' ss ln + V fp 2V fp + q ni C ' ox kT N D , poly Q ' bo Q ' ss = V fp ln + q ni C ' ox

4qN A si (kT q) ln( N A ni ) Q ' ss kT N D , poly ln + ' q NA C ' ox C ox By taking derivative on both sides with respect to temperature (T), we have, 4qN A si (k q ) ln( N A ni ) VTHN k N D , poly = ln + q NA T 2. T .C ' ox VTHN = 4qN A si (kT q ) ln( N A ni ) VTHN k N D , poly = ln + q NA T 2.T .C ' ox

N D , poly = 10 20 , N A = 1015 ,

VT kT k = = 0.085mv / K . = q T T q VTHN k 10 20 = ln 15 = 0.9786 mV / K . T q 10

Plugging in the numbers we get With the contributions from

Q ' bo = 30mv included at T=300K we get C ' ox

VTHN k N D , poly Q 'bo = -0.9786 + 0.05 =-0.9286 mV/K. = ln + T q NA 2.T .C ' ox

PROBLEM 9.23 (1) The NMOS is in saturation as a constant current is flowing through a gate- drain connected MOSFET.The expression for drain current for the short channel process is:
I DS = satn * W * C ox '*( V ovn V DSsat ) ...(1) . Substituting values for satn , W, Cox ' and VDSsat from table9.2.The values are at room temperature=270C

10*10-6= (110*109 um/s)*(50um)*(25fF/um2)*(VGS 0.28-0.05) (@270C) VGS=0.33V. Since the source is at ground, the output voltage=0.33V Simulated value of the output= 0.3535V. From equation (1) I ds = v satn * W * C ox '*(V GS V thn V DSsat ) I DS V GS = + V thn + V DSsat v satn * W * C ox ' Neglecting the change of vsatn , VDSsat and oxide charge with temperature. VGS Vthn = T T Vthn When temperature increases, threshold voltage decreases. 0.6mV / T VGS =-0.6mV/0C T VGS VGS = VGS 0 + (T-T0) where VGS =0.33V (@room temp=270C). T VGS =0.33 + (-0.6mV/0C)*(T-27)..(3) The hand calculated and simulated values are shown below: Temperature (0C) 0 50 100 150 Output or Gate Voltage (V) Simulations Calculations 0.3701 0.3462 0.3398 0.3162 0.3115 0.2862 0.2843 0.2562

C (2)

Circuit for problem 9.23

(2) The PMOS is also in saturation.The source is fixed@ 5V.The expression for drain current for drain current of PMOS is given by:
I SD = satp * W * C ox '*( V ovn V SDsat ) ..(4) where Vovn=VSG-Vthp=VS-VG-Vthp ...(5).

Substituting the values for satn , W, Cox ' and VDSsat from table9.2. 10*10-6=(9*109um/s)*(100um)*(25fF/um2)*(1-VG-0.28-0.05) VG=0.67V.This is the output voltage of the PMOS circuit @T=27 0C. Simulations result in an output voltage of 0.647V @T=27 0C. Deriving the equation for the variation of VSG with temperature for PMOS just like derived for NMOS results in the following equation:
VSG

=0.33 + (-0.6mV/0C)*(T-27)..(6)

VG=VS-[0.33 +(-0.6mV/0C)*(T-27)].. (7) The hand calculated and simulated values are shown below: Temperature (0C) 0 50 100 150 Output or Gate Voltage (V) Simulations Calculations 0.6307 0.6538 0.6605 0.6838 0.6887 0.7138 0.7166 0.7438

Circuit for problem 9.23

NETLIST FOR THE SIMULATIONS: *problem 9_23 *control statements .options scale=50nm . control destroy all set temp=0 run print d set temp=50 run print d set temp=100 run print d set temp=150 run print d .endc *circuit netlist *m1 d d s s pmos l=2 w=100 m2 d d 0 0 nmos l=2 w=50 *Ibias d Ibiasn *Vdd s Vddn .op 0 vdd 0 vdd DC d DC 0 10u DC 1 DC

10u

9.24. Prove using simulation outputs that the GFT product is constant in the saturation
region for different biasing conditions on a long channel process. Since GFT=gm*r0*fT, we will generate these three parameter for three different biasing using our 1u models. The three biasing currents will be set by forcing VGS to 1.5V, 2V, and 2.5V. The following file was used to simulate gm and ID with Winspice: * ** Problem 9.24 Homework Finding GM using LEVEL3 models *** .control destroy all run let ID = abs(vdd#branch) let GM = deriv(ID) plot ID plot GM .endc vdd vdd 0 dc 5V vg vg 0 dc 1V m1 vdd vg 0 0 nmos w=10 l=2 .DC vg 1.5V 2.5V 0.01V .option scale=1u ** Include Model File Here **** .end The plot for ID and gm are shown below:

Therefore: ID @ VGS=1.5V, 2V, 2.5V = 120uA, 300uA, and 530uA. gm @ VGS=1.5V, 2V, 2.5V = 300uA/V, 420uA/V, 500uA/V.

We will plot ID versus VDS at a constant VGS to calculate r0 (output resistance) in the saturation region. One over the slope of the line (1/derivative(ID with respect to VDS )) in the saturation region is equal to r0. The following file was used to calculate r0 for each bias condition and must be simulated three times with the different vg voltages: * Problem 9.24 Homework Finding R0 using LEVEL3 models .control destroy all run let ID1 = abs(vdd#branch) let R1 = 1/deriv(ID1) plot ID1 plot R1 .endc vdd vdd 0 dc 3V vg vg 0 dc 1.5V m1 vdd vg 0 0 nmos w=10 l=2 .DC vdd 0V 5V 0.01V .options scale=1um ** Include Model File Here **** .end The plot for ID versus VDS at VGS=1.5V and r0 at VGS=1.5V, 2V, and 2.5V are shown below:

Therefore: r0 @ VDS=5V and VGS=1.5V, 2V, 2.5V = 980K, 370K, and 200K since R1 is r0 at VGS=1.5V, R2 is r0 at VGS=2V, and R3 is r0 at VGS=2.5V. IDSSAT at VGS=1.5V, 2V, 2.5V = 110uA, 280uA, and 500uA. Since VDSSAT = VGS VTHN, VDSSAT=0.7V at VGS=1.5V, VDSSAT=1.2V at VGS=2V, and VDSSAT=1.7V at VGS=2.5V. To calculate the GFT product, we need to find the fT at our three bias points. FT is found by running an AC analysis of a transistor in the saturation region with the AC signal applied to the gate terminal for the three VGS bias values. The value of fT is the frequency where |id| / |ig| = 0db. Plotting the logrithum of |id| / |ig| versus frequency and fT is the frequency where this quanity = 0. The following file was used to calculate fT for each bias condition and must be simulated three times with the different vg voltages: * Problem 9.24 Homework Finding FT using LEVEL3 models .control destroy all run let FT1 = log(abs(vdd#branch) / abs(vg#branch)) plot FT1 .endc vdd vdd 0 dc 5V vg vg 0 dc 1.5V ac 1mV m1 vdd vg 0 0 nmos w=10 l=2 .AC lin 100 1G 5G .options scale=1um ** Include Model File Here **** .end

The plot for log(abs(id) / abs(ig)) versus frequency at VGS=1.5V, 2V, and 2.5V are shown below with fT being the value at 0db:

Therefore: fT @ VGS=1.5V, 2V, 2.5V = 1.9GHz, 2.7GHz, and 3.2GHz since FT1 is fT at VGS=1.5V, FT2 is fT at VGS=2V, and FT3 is fT at VGS=2.5V. For VGS = 1.5V => GFT = gm * r0 * fT = 300uA/V * 980K * 1.9GHz VDSSAT = 0.7V GFT = 558.6GHz For VGS = 2V => GFT = gm * r0 * fT = 420uA/V * 370K * 2.7GHz VDSSAT = 1.2V GFT = 419.6GHz For VGS = 2.5V => GFT = gm * r0 * fT = 500uA/V * 200K * 3.2GHz VDSSAT = 1.7V GFT = 320GHz Equation 9.59 is GFT = 3 * un / (2 * pi * L * L * lambda) where lambda = 1 / (r0 * IDSSAT). We are trying to show that GFT is approximately independent of biasing conditions. From VGS = 1.5V to 2.5V or over a 120uA to 530uA range (4.4X increase), GFT varied from 559GHz to 320GHz or decreased by 42%. Simulations showed that GFT decreases as the bias current is increased.

Name Vijayakumar Srinivasan Problem 9.25 To calculate the ft of a short channel device and verify the same with simulation. The ft of a device is given by, ft= (3Un*Vdssat)/(4Pi*(L^2))= gm/(2*Pi*Cgs) We know for a short channel device gm= 150uA/V, Cgs= 4.17fF So, ft=5.72GHz This is close to the theoretical value of 6GHz Using simulation, with short channel models, .control destroy all

run Let ft=mag(VDS#branch)/mag(VGS#branch) plot 20*log(ft) .endc .option scale=50n .ac dec 100 100M 10G VDS VGS M1 VDS VGS VDS 0 0 VGS DC DC 0 1 350m 0

AC 1m NMOS L=2 W=50

* BSIM4 models (model statements are not listed here) .model nmos nmos level = 14 .model pmos pmos level = 14 .end

Using a 1GHz to 10GHz scale, we get a ft close to 6.5GHz

Problem 9.26
VDD =1V

100/2

M3

50/2

50/2

M1

M2

1mV
+ 0.5V 20 uA

0.5V

+ -

DC operating points: The gates of both M1 and M2 are at 0.5v and the sources of M1 and M2 are tied together VGS1=VGS2 and ID1 =ID2=10uA For short channel devices

VGS 1 = VGS 2 =

ID + VTHN + VDSsat v sat .C OX '.W

Substituting the values from the Table 9.2 for short channel devices we get VGS1=VGS2=350mv For PMOS M3 gate drain connected mosfet

VSG 3 =

ID + VTHP + VSDsat v sat .C OX '.W

Substituting the values from the Table 9.2 for short channel devices we get VSG3=350mv Therefore Drain voltage of M1 is VD1=VG3=VD3= VDD-VSG3 VD1=650mv Drain Voltage of M2 =VDD=1v

Ac Analysis: The tranconductance of M1 and M2 is

g m1 = g m 2 = v sat .C OX '.W
using table 9.2 gm1=gm2=150uA/V We can replace Drain gate connected mosfet M3 with a resistor of 1/gm3 Where gm3 is calculated using table 9.2 as gm3=150uA/V Ac analysis of the circuit is 1mv= vgs1 - vgs2 =

id1 id 2 gm1 gm2

Here gm1=gm2 and id1=-id2 Therefore vgs1=-vgs2=0.5mv The AC Drain currents are id1=id3=gm1.vgs1=150uA/V . 0.5mV =75nA Since id1=-id2, id2=-75nA Therefore overall(AC+DC) drain currents are iD1 = 10 + 0.075 SIN(2f) uA iD2 = 10 - 0.075 SIN(2f) uA AC drain voltages of M1 and M3 is vd1=-id1. 1/gm3 =75n /150u = - 0.5mV AC+DC drain voltages of M1 and M3 is vD1 = 650 - 0.5 SIN(2f) mv For calculating AC drain voltage of M2 Output resistance of M2 is ro Since M2 is in saturation ro= 1/.ID For short channel devices =0.6/V and ID for M2 is 10uA ro=167k ohms

AC drain voltages of M2 vd2=id2. ro =12.45mv AC+DC drain voltages of M1 and M3 is vD2 =1+0.01245 SIN(2f) v Since vD2 is 1+ac voltage there fore vD2 will stay at vdd since it cant go beyond vdd.

Simulations
*** Problem 9.26 CMOS: Circuit Design, Layout, and Simulation *** .control destroy all run ** for the operating point analysis *print all *let vgs1=vg1-vs12 *let vgs2=vg2-vs12 *print vgs1 vgs2 vd13 let vd2=vdd ** for the AC analysis *plot mag(vd13) mag(vdd) ** for the transient analysis plot vd13 plot vd2 .endc .option scale=50n *.op *.ac dec 100 1 10k .tran 1u 300u VDD VDD 0 DC 1 VG1 VG1 0 DC 0.5 AC 1m SIN 2.5 1m 10k VG2 VG2 0 Dc 0.5 Ibias VS12 0 DC 20u M1 VD13 VG1 VS12 VS12 NMOS L=2 W=50 M2 VDD VG2 VS12 VS12 NMOS L=2 W=50 M3 VD13 VD13 VDD VDD PMOS L=2 W=100

DC Operating Point vgs1 = 3.434905e-01 vgs2 = 3.434905e-01 vd13 = 6.525805e-01

Problem 9.27 The thermal noise of a MOSFETs drain current when operating in saturation is given by Equation (9.63).

IR (f) =
2

4 KT 3 1 * 2 gm

where the resistance is

3 1 * 2 gm
Rch = 1 gm

When the MOSFET is in DEEP TRIODE region, resistance is given by from equation (9.16)

In between the deep triode and saturation regions, Thermal noise can be modeled with

where 1 < < 3/2.

1 gm

Problem 9.28 If we look at equation 9.66 we see that the total PSD of the mosfet drain noise current is proportional to the gm IM2 gm So if we decrease gm we can decrease IM2. but, It will also decrease the signal to noise ratio (SNR). We would like to have as large of a signal to noise ratio as possible. Lets take a closer look. Signal to Noise ratio = current through transistor/current noise For the current through the transistor, let us take its square so we have; . ids2 = gm2*vgs2 so our signal to noise ratio becomes; SNR =

gm 2 v gs
AF

KF I D 8kT + gm 2 3 f Cox LW

If we then multiply the denominator by gm2/gm2 then our SNR becomes; SNR =
V gs
KF

8kT 3 gm Since the gm2 is proportional to ID then the first term of the denominator wont change much as gm decreases. When we decrease gm the second term of the denominator will increase which will cause the SNR to decrease. For an amplifier we would like to have a large SNR and decreasing gm will decrease the SNR so although at first it appears to be a good way to decrease the noise, for an amplifier it negatively affects the SNR and is not a good idea.
ID
AF

f COX LWgm 2

9.29

Show how the thermal noise resistance of the channel seen in Eq. (9.63) is derived for the MOSFET operating in the saturation region.

Equation (6.46) can be re-written without the area dependence as Q

= 2 C ox (V GS V THN ) 3

Plugging this into Eq. (6.27) and integrating

dR =

2 0 n 3

dy 1 C ox (V GS V THN ) W

Evaluating the integral gives R ch =

W C L n ox

1 1 =3g (V GS V THN ) 2 m

which is the result seen in Eq. (9.63).