Fosroc Renderoc BF constructive solutions

Fair faced, one component polymer modified

cementitious filler and reprofiling mortar

Uses Properties

Renderoc BF is designed for application to imperfections in The following results were obtained at a water:powder ratio
concrete and masonry surfaces. It is suitable for application of 0.2
upto 5mm thickness, and can be used in the following
situations: Property
Initial setting time (BS EN 196) : 115 mins
 Filling blow holes prior to overcoating
Final setting time (BS EN 196) : 165 mins
 Skim-coat over concrete to receive protective coatings Fresh wet density : 1840 kg/m3
Compressive strength : 3days - 10N/mm²
 General reprofiling over large areas
7days - 20N/mm²
 Reprofiling, in association with other Renderoc mortars Average Linear Coefficient :
of Thermal Expansion : 2.5 x 10-6 per oC
Advantages
Note : Working life and setting time will vary dependent
 Cost effective/ time saving - no independent primer or on ambient, substrate temperatures and wind
curing agents required speed.

 High performance - excellent bond to substrate

Instructions for use
 User friendly - requires addition of water only
Preparation
 Suitable to receive protective coatings
Clean the surface and remove any dust, unsound material,
plaster, oil, paint, grease, corrosion deposits or algae.
Description
Roughen the surface to remove any laitance and expose the
Renderoc BF is supplied as a ready to use blend of dry fine aggregate by light scabbling or sweep blasting.
powders and polymers, which requires only the addition of
Oil and grease deposits should be removed by steam
water to produce a highly consistent cementitious mortar,
cleaning, detergent scrubbing or the use of a proprietary
with good handling characteristics.
degreaser. The effectiveness of decontamination should then
Renderoc BF exhibits excellent thermal compatibility with be assessed by a pull-off test.
concrete and is fully compatible with other Renderoc*
The cleaned areas should be blown clean with oil-free
mortars and Dekguard* protective coatings.
compressed air before continuing. All prepared areas should
be thoroughly soaked with clean water immediately prior to
Design Criteria
the application of Renderoc BF. Any residual surface water
Renderoc BF is designed for vertical and overhead use to should be removed prior to commencement.
infill surface imperfections of concrete upto 5mm thick.
Mixing

Limitations Care should be taken to ensure that Renderoc BF is thor-

- Renderoc BF should not be used when the temperature oughly mixed. In all cases the powder component should be
is below 5°C and falling. introduced into water.

- Do not proceed with the application when rainfall is Mixing should be carried out in a suitably sized mixing
imminent unless in a sheltered or protected situation. vessel, using a slow speed (400/500 rpm), heavy duty drill
- If any doubts arise concerning temperature or substrate and a Fosroc mortar mixing paddle.
conditions, consult the local Fosroc office. Pour 4 - 6litres of water (depending of workability required)
into the mixer and, with the machine in operation, add one
full 20 kg bag of powder, then mix for 3 to 5 minutes, until
fully homogeneous. Do not use more than 6 litres of water
Renderoc BF

per 20kg bag.

Fosroc Renderoc BF

If mixing small quantities by hand, Renderoc BF should be Estimating

volume-batched. Add 3 volumes of the Renderoc BF powder
Supply
(loose-filled to excess and struck off level with the top of the
Renderoc BF : 20 kg bag
measuring container) to one volume of potable water. This
should be mixed vigorously until fully homogeneous. Yield
Renderoc BF : 14.4 litres per 20kg bag
Application
(based on 6litre water)
Apply the mixed Renderoc BF to the blow holes by steel
Actual coverage of Renderoc BF will be wholly dependent
trowel. It should be applied with minimum working and be
upon the general substrate condition. It is recommended,
allowed to partly set before finally trowelling to a smooth
therefore, that site trials over a typical area are carried out to
finish. If a very smooth finish is required, a small amount of
determine actual usage.
water may be flicked on to the surface of the Renderoc BF
with a paint brush prior to final trowelling.
Storage
Curing
Shelf life
Curing is not generally required. However, under extreme
All products have a shelf life of 12 months if kept in a dry
conditions - high temperatures and drying winds - use
store in the original, unopened bags or packs @ 25oC. If
Nitobond AR*† or Nitocote PE135*† as a curing agent, or
stored at high temperatures and/or high humidity conditions
cover the surface with polythene sheeting, taped down at the
the shelf life may be considerably reduced to 4 to 6 months.
edges.

Nitobond AR does not require mechanical removal prior to Precautions

overcoating with Dekguard system. If overcoating with epoxy
Health and safety
or polyurethanes then use Nitocote PE135 as the curing
membrane. Renderoc BF contains cement powders which, when mixed
or become damp, release alkalis which can be harmful to the
Cleaning
skin. During use, avoid inhalation of dust and contact with
Renderoc BF should be removed from tools, equipment and skin and eyes. Wear suitable protective clothing, gloves, eye
mixers with clean water immediately after use. Cured protection and respiratory protective equipment. The use of
material can only be removed mechanically. barrier creams provide additional skin protection. In case of
contact with skin, rinse with plenty of clean water, then
High temperature working
cleanse with soap and water. In case of contact with eyes,
At ambient temperatures above 35°C, the components rinse immediately with plenty of clean water and seek
should be placed in air-conditioned storage of less than medical advice. If swallowed, seek medical attention immedi-
25°C, for special application procedures, refer to your local ately - do not induce vomiting. For further information, refer
Fosroc office. to the Product Material Safety Data Sheet.

Overcoating with protective / decorative finishes Fire

Renderoc BF may be overcoated after 48 hours, in ambient Renderoc BF is a non-flammable product.

conditions of up to 75% relative humidity, dependant on the
type of coating. For further information consult the local * Denotes the trademark of Fosroc International Limited
Fosroc office before proceeding. †
See separate data sheet
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.

Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
United Arab Emirates Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com
www.fosroc.com

UAE/0492/13/I