7 130

Oil Burner Controls LMO14...

LMO24...
LMO44...
Microcontroller-based oil burner controls for the startup, supervision and control
of forced draft oil burners in intermittent operation.
Maximum oil throughput up to 30 kg/h, also above 30 kg/h on some versions.

The LMO14, LMO24, LMO44 and this Data Sheet are intended for use by OEMs
which integrate the burner controls in their products.

Use, features

Use The LMO are designed for the startup and supervision of 1- or 2-stage forced draft oil
burners in intermittent operation.
Yellow-burning flames are supervised with photo resistive detectors QRB1 / QRB3 or
yellow flame detector QRB4, blue-burning flames with blue flame detector QRC.
In terms of housing dimensions, electrical connections and flame detectors, the LMO
are identical with the LOA oil burner controls.

∂ Applications in accordance with EN 267: Automatic forced draft burners for liquid
fuels
∂ Type-tested and approved in accordance with DIN EN 298

Features ∂ LMO44 for use with stationary direct-fired air heaters

∂ Undervoltage detection
∂ Electrical remote reset
∂ Bridging contact for oil preheater
∂ Monitoring of time for oil preheater
∂ Accurate and reproducible control sequence thanks to digital signal handling
∂ Controlled intermittent operation after 24 hours of continuous operation
∂ Limitation of the number of repetitions
∂ Multicolor indication of fault status and operational status messages

CC1N7130en
Building Technologies
15.03.2018
Supplementary documentation

Product type Type of documentation Documentation number

LMO Environmental declaration E7130
ACS410 Software documentation J7352
OCI400 Data sheet N7614
QRB1 / QRB3 Data sheet N7714
QRB4 Data sheet N7720
QRC1 Data sheet N7716

Warning notes

To avoid injury to persons, damage to property or the environment, the following

warning notes must be observed!

Do not open, interfere with or modify the unit!

∂ All activities (mounting, installation and service work, etc.) must be performed by
qualified staff
∂ Before making any wiring changes in the connection area, completely isolate the
plant from mains supply (all-polar disconnection). Ensure that the plant cannot be
inadvertently switched on again and that it is indeed dead. If not observed, there is
a risk of electric shock hazard
∂ Ensure protection against electric shock hazard by providing adequate protection
for the burner control’s connection terminals. If this is not observed, there is a risk
of electric shock
∂ Each time work has been carried out (mounting, installation, service work, etc.),
check to ensure that wiring is in an orderly state and make the safety checks as
described in «Commissioning notes». If not observed, there is a risk of
impairment of safety functions and of electric shock hazard
∂ Press the lockout reset button / operation button or the AGK20… lockout reset
button extension only manually (applying a force of no more than 10 N) without
using any tools or pointed objects. If not observed, there is a risk of impairment
of safety functions and of electric shock hazard
∂ Fall or shock can adversely affect the safety functions. Such units must not be put
into operation, even if they do not exhibit any damage. If not observed, there is a
risk of impairment of safety functions and of electric shock hazard
∂ When replacing LOA26 or LOA36, any ARK21 remote lockout reset module or
ARK21... similar modules fitted in the burner or boiler must be removed.
If this is not observed, there is a risk of loss of safety functions and a risk of electric
shock

Mounting notes

Ensure that the relevant national safety regulations are complied with.

Installation notes

∂ Always run the high-voltage ignition cables separately while observing the greatest
possible distances to the unit and to other cables
∂ Install switches, fuses, earthing, etc., in compliance with local regulations
∂ Ensure that the maximum permissible amperages will not be exceeded (refer to
«Technical data»)
∂ Do not feed external mains voltage to the control outputs of the unit. When testing
the components controlled by the burner control (fuel valves, etc.), the LMO may
never be plugged in
∂ Do not mix up live and neutral conductors

2/18

Building Technologies CC1N7130en

15.03.2018
Electrical connection of the flame detectors

It is important to achieve practically disturbance- and loss-free signal transmission:

∂ Never run the detector cable together with other cables
– Line capacitance reduces the magnitude of the flame signal
– Use a separate cable
∂ Observe the maximum permissible lengths of the detector cables (refer to
«Technical data»)
∂ Earth the burner in compliance with the relevant regulations; earthing the boiler
alone does not suffice

Commissioning notes

When commissioning the plant or when doing maintenance work, make the following
safety checks:

Safety check Anticipated response

a) Burner startup with flame detector darkened Non-alterable lockout at the end
of the safety time (TSA)
b) Burner startup with flame detector exposed Non-alterable lockout within 40
to extraneous light seconds
c) Burner operation with simulated loss of Repetition followed by the non-
flame; for that purpose, darken the flame alterable lockout at the end of
detector during operation and maintain that safety time (TSA)
state

3/18

Building Technologies CC1N7130en

15.03.2018
Standards and certificates

Applied directives:
∂ Low-voltage directive 2014/35/EC
∂ Directive for pressure devices 2014/68/EC
∂ Electromagnetic compatibility EMC (immunity) *) 2014/30/EC
*) The compliance with EMC emission requirements must be checked after the burner control is
installed in equipment

Compliance with the regulations of the applied directives is verified by the adherence to
the following standards / regulations:
∂ Automatic burner control systems for burners and appliances DIN EN 298
burning gaseous or liquid fuels
∂ Safety and control devices for burners and appliances DIN EN 13611
burning gaseous and/or liquid fuels — General requirements
∂ Automatic electrical controls for household and similar use DIN EN 60730-2-5
Part 2-5:
Particular requirements for automatic electrical burner control
systems

The relevant valid edition of the standards can be found in the declaration of
conformity!

Β Note on DIN EN 60335-2-102

Household and similar electrical appliances - Safety - Part 2-102:
Particular requirements for gas, oil and solid-fuel burning appliances having electrical
connections. The electrical connections of the LMO and the AGK11 comply with the
requirements of EN 60335-2-102.

EAC Conformity mark (Eurasian Conformity mark)

ISO 9001:2015
ISO 14001:2015
OHSAS 18001:2007

China RoHS
Hazardous substances table:
http://www.siemens.com/download?A6V10883536

Service notes

The service adapters can only be used for a short time. They may only be used in
supervised operation by qualified staff.

4/18

Building Technologies CC1N7130en

15.03.2018
Life cycle

Burner controls has a designed lifetime* of 250,000 burner startup cycles which, under
normal operating conditions in heating mode, correspond to approx. 10 years of usage
(starting from the production date given on the type field).

This lifetime is based on the endurance tests in the standard EN 298.

A summary of the conditions has been published by the European Control
Manufacturers Association (Afecor) (www.afecor.org).

The designed lifetime is based on use of the burner controls according to the
manufacturer’s Data Sheet. After reaching the designed lifetime in terms of the number
of burner startup cycles, or the respective time of usage, the burner control is to be
replaced by authorized personnel.

* The designed lifetime is not the warranty time specified in the Terms of Delivery

Disposal notes

The unit contains electrical and electronic components and must not be disposed of
together with domestic waste.
Local and currently valid legislation must be observed.

Mechanical design

The housing is made of impact-proof, heat-resistant and flame-retarding plastic.

It is of plug-in design and engages audibly in the base. Burner controls LMO are
designed in black plastic.

The housing accommodates the

∂ microcontroller for the control sequence and the print relays for load control
∂ electronic flame signal amplifier
∂ lockout reset button with its integrated multicolor signal lamp (LED) for operational
status and fault status messages and the socket for connecting the OCI400
interface or the AGK20 lockout reset button extension

Indication and ∂ Multicolor indication of operational status and fault status messages
diagnostics ∂ Transmission of operational status and fault status messages and detailed service
information via additional OCI400 interface and ACS410 PC software

5/18

Building Technologies CC1N7130en

15.03.2018
Type summary

Times Comparable type

Mains Fuel valve Burner Remote
Article no. Type reference ¹) of
voltage stages capacity reset tw t1 / t1´ TSA t3 t3n t4 LOA 4)
max. min. max. min. max. min.
Standard versions
LOA24.171B27
BPZ:LMO14.111C2 LMO14.111C2 AC 230 V 1 <30 kg/h ∂ ∂ 2,5 s 15 / 16 s 10 s 15 s 10 s --- LOA26.171B27 ²)
LOA36.171A27 ²)
BPZ:LMO14.113C2 LMO14.113C2 AC 230 V 1 <30 kg/h ∂ ∂ 2,5 s 15 / 16 s 10 s 15 s 3s --- LOA24.173A27 ³)
LOA24.171B27
BPZ:LMO24.111C2 LMO24.111C2 AC 230 V 2 <30 kg/h ∂ ∂ 2,5 s 15 / 16 s 10 s 15 s 10 s 15 s LOA26.171B27 ²)
LOA36.171A27 ²)
Suitable for flash-steam generators
BPZ:LMO24.111C1 LMO24.111C1 AC 120 V 2 <30 kg/h ∂ ∂ 2,5 s 15 / 16 s 10 s 15 s 10 s 15 s LOA24.171B17
BPZ:LMO24.011C2 LMO24.011C2 AC 230 V 2 <30 kg/h ∂ ∂ 2,5 s 5/6s 10 s 5s 10 s 15 s LOA24.571C27
Suitable for use with air heaters (WLE)
BPZ:LMO24.255C2 LMO24.255C2 AC 230 V 2 < / >30 kg/h ∂ ∂ 2,5 s 25 / 26 s 5s 25 s 5s 15 s ---
BPZ:LMO44.255C2 LMO44.255C2 AC 230 V 2 < / >30 kg/h ∂ ∂ 2,5 s 25 / 26 s 5s 25 s 5s 5s LOA44.252A27

Legend

TSA Ignition safety time

tw Waiting time
t1 Prepurge time
t1´ Purge time
t3 Preignition time
t3n Postignition time
t4 Interval from flame signal to release of fuel valve 2 (BV2)
¹) Bridging contact for oil preheater
²) No actuator (SA) function
³) In case of replacement, ignition transformer must be rewired from terminal 7 (LOA) to terminal 6 (LMO)
)
4 LMO can replace LOA, but the instructions given in the Data Sheet, other technical documentation and the specification must be followed

6/18

Building Technologies CC1N7130de

15.03.2018
Test adapter (must be ordered separately)

Test adapter KF8833

Article no.: BPZ:KF8833
∂ For checking the functions of burner controls on the
burner
∂ With signal lamps for program indication
∂ With one pair of jacks for measuring the flame detector
current

Test adapter KF8840

Article no.: BPZ:KF8840
∂ For checking the functions of burner controls on the
burner
∂ With signal lamps for program indication
∂ With on / off switch for simulating the flame signal
∂ With holes for checking the control voltages at the tabs of
the burner control
∂ With one pair of jacks for measuring the flame detector’s
resistance

Test adapter KF8885

Article no.: BPZ:KF8885
∂ For checking the functions of burner controls on the
burner
∂ With switch for manual startup of the burner
∂ With switch for simulating the oil preheater’s release
contact
∂ With 2 pairs of jacks for measuring the flame detector
current
See operating instructions B7986.

7/18

Building Technologies CC1N7130en

15.03.2018
Accessories (must be ordered separately)

Connection accessories
Plug-in base AGK11
for small burner controls
Article no.: BPZ:AGK11
To connect the small-capacity burner controls to the burner
plant.
See data sheet N7201

Cable holders AGK66

Article no.: BPZ:AGK66
For plug-in base AGK11
See data sheet N7201

Cable holders AGK65

Article no.: BPZ:AGK65
For plug-in base AGK11
See data sheet N7201

Flame detectors
Photo resistive detectors QRB1
See data sheet N7714

Photo resistive detectors QRB3

See data sheet N7714.

Yellow flame detector QRB4

See data sheet N7720.

Frontal illumination:

Blue-flame detectors QRC

See data sheet N7716.
Lateral illumination:

8/18

Building Technologies CC1N7130en

15.03.2018
Accessories (must be ordered separately) (cont’d)

Service tools Optical interface OCI400

Article no.: BPZ:OCI400
∂ Optical interface between burner control and PC
∂ Facilitates viewing and recording setting parameters on
site in connection with the ACS410 PC software
See data sheet N7614.

PC software ACS410
Article no.: BPZ:ACS410
PC software for setting the parameters and for visualizing the
burner controls.
See software documentation J7352.

Others

Extension of lockout reset button AGK20

9/18

Building Technologies CC1N7130en

15.03.2018
Technical data

General unit data Mains voltage AC 230 V +10 % / -15 %

AC 120 V +10 % / -15 %
Mains frequency 50...60 Hz ±6 %
External primary fuse (Si) 6.3 A (slow)
Power consumption 12 VA
Perm. mounting orientation Optional
Weight Approx. 200 g
Safety class I (burner control with plug-in base)
Degree of protection IP40 (to be ensured through mounting)
Cable lengths
∂ QRB1 / QRB3 Max. 10 m at 100 pF/m (laid separately)
∂ QRB4 Max. 3 m at 100 pF/m (laid separately)
∂ QRC Max. 10 m at 100 pF/m (laid separately)
Detector cable laid separately Max. 10 m
Remote reset laid separately Max. 20 m

Perm. current at cosι ″ 0.6 LMO14 LMO24 LMO44

Terminal 1 Max. 5 A Max. 5 A Max. 5 A
Terminals 3 and 8 Max. 3 A Max. 3 A Max. 3 A
Terminals 4 and 5 Max. 1 A Max. 1 A Max. 1 A
Terminal 6 Max. 1 A Max. 2 A Max. 2 A
Terminal 10 Max. 1 A Max. 1 A Max. 1 A

Environmental Storage DIN EN 60721-3-1

conditions Climatic conditions Class 1K3
Mechanical conditions Class 1M2
Temperature range -20...+60 °C
Humidity <95 % r.h.
Transport DIN EN 60721-3-2
Climatic conditions Class 2K2
Mechanical conditions Class 2M2
Temperature range -20...+60 °C
Humidity <95 % r.h.
Operation DIN EN 60721-3-3
Climatic conditions Class 3K3
Mechanical conditions Class 3M3
Temperature range
- LMO14 / LMO24 -5...+60 °C
- LMO44 -20...+60 °C
Humidity <95 % r.h.
Installation altitude Max. 2,000 m above sea level

Attention!
Condensation, formation of ice and ingress of water are not permitted! If this is
not observed, there is a risk of loss of safety functions and a risk of electric
shock.

10/18

Building Technologies CC1N7130en

15.03.2018
Technical data (cont´d)

Flame supervision with Detector current Perm. detector Possible detector current
QRB or QRC required current with flame
(with flame) (without flame) (typically)
QRB1 ¹) Min. 45 µA Max. 5,5 µA 100 µA
QRB3 ¹) Min. 45 µA Max. 5,5 µA 100 µA
QRB4 ¹) Min. 45 µA Max. 5,5 µA 70 µA
QRC ¹) Min. 45 µA Max. 5,5 µA 70 µA

¹) The values given in the table above only apply under the following conditions:
- Mains voltage depending on execution AC 120 V or AC 230 V
- Ambient temperature 23 °C

Green signal lamp Detector current in operation: Detector current in operation:

(LED) for indication of - Flame signal instable - Flame signal stable
operating state - Green signal lamp (LED) - Green signal lamp (LED) steady on
flashing
QRB ¹) <45 µA >45 µA
QRC ¹) <45 µA >45 µA

¹) The values given in the table above only apply under the following conditions:
- Mains voltage depending on execution AC 120 V or AC 230 V
- Ambient temperature 23 °C

Measuring circuit QRB QRC

for detector current
11 12 LMO... 11 12 1 LMO...
Legend
bl sw 7130v01/0700
bl sw br 7130v02/0700
+ +
µA DC DC microammeter
with an internal
µA DC µA DC
resistance of
Ri = max. 5 kς
bl Blue
sw Black
br Brown
QRB... QRC1...

As an alternative to detector current measurement, the Interface OCI400 with PC

software ACS410 can be used. In that case, the DC microammeter is not required.

Note!
QRB4 cable connection!
Β Connect the blue QRB4 cable to terminal 11.
Connect the black QRB4 cable to terminal 12.
Otherwise the QRB4 will not function.

11/18

Building Technologies CC1N7130en

15.03.2018
Function

Preconditions for ∂ Burner control is reset

startup ∂ Reset button «EK1» or «EK2» not used
∂ All contacts in the line are closed, heat demand
∂ No undervoltage
∂ Flame detector is darkened and there is no extraneous light

Undervoltage ∂ Safety shutdown from the operating position takes place should mains voltage drop
below about AC 165 V (with U N = AC 230 V) or AC 75 V (with U N = AC 120 V)
∂ Restart is initiated when mains voltage exceeds about AC 175 V (with U N = AC 230
V) or AC 95 V (with UN = AC 120 V)

Time supervision If the oil preheater’s release contact does not close within 10 minutes, a non-alterable
oil preheater lockout takes place.

Controlled intermittent After no more than 24 hours of continuous operation, the burner control will initiate
operation automatic controlled shutdown followed by a restart.

Control sequence in If a non-alterable lockout occurs, the outputs for the fuel valves, the burner motor and the
the event of fault ignition equipment are always immediately deactivated (<1 second).
In the event of a non-alterable lockout, the LMO remains locked and the red signal lamp
(LED) lights up permanently.
The burner control can immediately be reset.
This state is also maintained in the case of mains failure.

Cause Response
Mains failure Restart
Voltage below undervoltage threshold Safety shutdown, followed by restart
Extraneous light during prepurge time (t1), 5 Non-alterable lockout at the end of the
s before fuel valve (BV1) release prepurge time (t1)
Extraneous light during waiting time (tw) Start prevention, a non-alterable lockout
occurs after a maximum of 40 seconds
No flame at the end of safety time (TSA) Non-alterable lockout at the end of the
safety time (TSA), blink code 2, see
Control sequence
Loss of flame during operation Maximum of 3 repetitions, then a non-
alterable lockout occurs
Oil preheater’s release contact does not Non-alterable lockout
close within 10 minutes

Resetting the After a non-alterable lockout, a reset can be carried out immediately. Press and hold the
burner control lockout reset button for about 1 second (<3 seconds). The LMO can be reset only when
all contacts in the line are closed and there is no undervoltage.

Ignition program with If the flame is lost during the safety time (TSA), the burner will be reignited before the
LMO14.113x2 and end of the safety time (TSA).
LMO24.113x2 This means that several ignition attempts can be made during safety time (TSA) (see
Control sequence).

Limitation of repetitions If the flame is lost during operation, a maximum of 3 repetitions can be carried out. If
the flame is lost for the fourth time during operation, the burner will initiate a non-
alterable lockout.
The repetition count is restarted each time controlled switching on by control thermostat
or pressurestat (R) takes place.

12/18

Building Technologies CC1N7130en

15.03.2018
Operation, display, diagnostics

Operation Lockout reset button «EK» is the key operating element for resetting

7130z05/0700
EK the burner control and for activating / deactivating the diagnostic
functions.

Red The multicolor signal lamp (LED) in the lockout reset button is the key

7130z06e/0700
Yellow indicating element for both visual diagnostics and interface diagnostics.
Green
LED

Both «EK» and LED are located under the transparent cover of the lockout reset
button.

There are 2 diagnostic choices:

1. Visual diagnostics: Operational status indication or diagnostics of the cause of
fault.
2. Interface diagnostics: With the help of the interface OCI400 and PC software
ACS410 or flue gas analyzers of different makes.

Visual diagnostics:
In normal operation, the different operating states are indicated in the form of color
codes according to the color code table given below.

Operational status During startup, status indication takes place according to the following table:
indication
Color code table for multicolor signal lamp (LED)
Status Color code Color
Waiting time «tw», other waiting states ........................................ Off
Oil preheater on ........................................ Yellow
Ignition phase, ignition controlled Flashing yellow
Operation, flame o.k. ......................................... Green
Operation, flame not o.k. (when detector Flashing green
current drops below the recommended
level for reliable operation)
Extraneous light on burner startup Green-red
Undervoltage Yellow-red
Fault, alarm ......................................... Red
Error code output (refer to «Error code Flashing red
table»)
Interface diagnostics Red flicker light

Legend ...... Steady on Red

Off Yellow
Green

13/18

Building Technologies CC1N7130en

15.03.2018
Operation, display, diagnostics (cont´d)

Diagnostics of the After a non-alterable lockout, the red signal lamp (LED) lights up.
cause of fault In that condition, the visual diagnostics of the cause of fault according to the error code
table can be activated by pressing the lockout reset button for more than 3 seconds.
Pressing the reset button again for at least 3 seconds, the interface diagnostics will be
activated. Interface diagnostics works only if the AGK20… lockout reset button
extension is not fitted. If, by accident, interface diagnostics has been activated, in which
case the slightly red light of the signal lamp flickers, it can be deactivated by pressing
again the lockout reset button for at least 3 seconds. The instant of switching over is
indicated by a yellow light pulse.

The following sequence activates the diagnostics of the cause of fault:

OCI400
Lockout position Lockout position Lockout position
Visual diagnostics Interface diagnostics
Flashing PC / analyzer
On
Reset
EK EK EK

7130z04e/0602
Error code table
>3s xxxx xxxx
xxxx xxxx
>3s <3s
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx

Error code table of multicolor signal lamp (LED)

Red blink code Alarm at Possible cause
of signal lamp term. 10
2 blinks On No establishment of flame at the end of safety time (TSA)
- Faulty or soiled fuel valves
- Faulty or soiled flame detector
- Poor adjustment of burner, no fuel
- Faulty ignition equipment
3 blinks On Free
4 blinks On Extraneous light on burner startup
5 blinks On Free
6 blinks On Free
7 blinks On Too many losses of flame during operation (limitation of the number of repetitions)
- Faulty or soiled fuel valves
- Faulty or soiled flame detector
- Poor adjustment of burner
8 blinks On Time supervision oil preheater
9 blinks On Free
10 blinks Off Wiring fault or internal fault, fault output contacts, faults that cannot be detected,
such as simultaneous faults, other faults

14/18

Building Technologies CC1N7130en

15.03.2018
Operation, display, diagnostics (cont´d)

During the time the cause of fault is diagnosed, the control outputs are dead
- The burner remains shut down
- the external fault indicator remains de-energized
- Fault status signal (alarm) at terminal 10, according to the error code table

The diagnostics of the cause of fault is quit and the burner switched on again by
resetting the burner control. Press the lockout reset button for about 1 second (<3
seconds).

15/18

Building Technologies CC1N7130en

15.03.2018
 Connection diagram and internal diagram LMO14 Control sequence LMO14

R A´ A B C D
W 1
EK1 µC1 µC control µC2
SB tw
LED OH 8

K1 K2 FSV
OW 3

K3
M 3
1 2 10 8 3 6 7 4 5 9 11 12
kbr
BV1 4
SB t3n
t1
8 3
Z 6
R QRB
OW EK2 bl sw t3 TSA
11
W FS
OH 12
AL
N QRC Only with LMO14.113C2: re-ignition
1 bl sw t3n t3n
Si
L M Z BV1 br Z 6
N
7130a01en/0518 11
FS
7130d02e/1207 12

Connection diagram and internal diagram LMO24 Control sequence LMO24

R A´ A B C D
µC control µC2 W 1
EK1 µC1
SB tw
LED OH 8

K2
K1 FSV OW 3
K3 t1´
K4 M 3
t1
1 2 10 8 3 6 7 4 5 9 11 12 BV1 4
kbr
SB t4
8 3 BV2 5
R QRB t3 t3n
OW EK2 bl sw
Z 6
W OH BV2 TSA
AL 11
FS
N QRC 12
Si 1 bl sw
Only with LMO24.113C2: re-ignition
L M Z BV1 br t3n t3n
N Z 6
7130a04en/0518

11
FS
7130d03e/1207 12

Connection diagram and internal diagram LMO44… Control sequence LMO44…

R A´ A B C D
µC control W 1
EK1 µC1 µC2
SB tw
LED OH 8

K2
K1 FSV OW 3
K3 t1´
M 3
K4 t1
1 2 10 8 3 6 7 4 5 9 11 12 BV1 4
kbr
t4
SB
8 3 BV2 5
R t3 t3n
OW EK2 QRB
bl sw Z 6
W TSA
OH BV2 11
AL FS
N 7130d05/1105 12
QRC
Si 1 bl sw

L M Z BV1 br

N
7130a04en/0518

16/18

Building Technologies CC1N7130en

15.03.2018
Legend

AL Alarm device
BVx Fuel valve
EK1 Lockout reset button
EK2 Remote lockout reset button
FS Flame signal
FSV Flame signal amplifier
Kx Contacts of control relay
kbr Cable link (required only when no oil preheater is used)
LED 3-color signal lamp
M Burner motor
OW Release contact of oil preheater
OH Oil preheater
QRB1 Photo resistive flame detector
QRB3 Photo resistive flame detector
QRB4 Yellow flame detector
QRC Blue-flame detector
bl = blue, br = brown, sw = black
R Control thermostat or pressurestat
SB Safety limit thermostat
Si External primary fuse
W Limit thermostat or pressure switch
Z Ignition transformer

TSA Ignition safety time

tw Waiting time
t1 Prepurge time
t1´ Purge time
t3 Preignition time
t3n Postignition time
t4 Interval from flame signal to release of fuel valve 2 (BV2)

A´ Start of startup sequence with burners using an oil preheater (OH)

A Start of startup sequence with burners using no oil preheater (OH)
B Time of flame establishment
C Operating position
D Controlled shutdown by control thermostat or pressurestat (R)

Control signals
Required input signals
Perm. input signals

µC1 Microcontroller 1
µC2 Microcontroller 2

17/18

Building Technologies CC1N7130en

15.03.2018
 Dimensions

Dimensions in mm

LMO 22

5,2
53,9

7130m04/1004
9
Plug-in base AGK11
88 41,6
91

47,2

62,5

LMO with extension of

lockout reset button
L

AGK20
7,44

7130m05/0904

Type reference Length «L» in mm

AGK20.19 19
AGK20.43 43
AGK20.55 55

 2018 Siemens AG Building Technologies, Berliner Ring 23, D-76437 Rastatt

18/18 Subject to change!

Building Technologies CC1N7130en

15.03.2018