Service Manual: Reciprocating Compressor Premium D

Service Manual
Reciprocating compressor
Premium D
No.: 9_5851 21 E
Manufacturer:
KAESER KOMPRESSOREN SE
96410 Coburg • PO Box 2143 • GERMANY • Tel. +49-(0)9561-6400 • Fax +49-(0)9561-640130
http://www.kaeser.com
Original instructions
/KKW/PPREM 2.01 en SBA-KOLBEN-ANLAGE 1-STUFIG
20131209 110916
Contents
1 Regarding this document

1.1 Using this document ......................................................................................................... 1
1.2 Further documents ........................................................................................................... 1
1.3 Copyright .......................................................................................................................... 1
1.4 Symbols and labels .......................................................................................................... 1
1.4.1 Warnings ............................................................................................................. 1
1.4.2 Potential damage warnings ................................................................................ 2
1.4.3 Other alerts and their symbols ............................................................................ 2
2 Technical Specifications
2.1 Nameplate ........................................................................................................................ 4
2.2 Options ............................................................................................................................. 4
2.3 Mass ................................................................................................................................. 4
2.4 Compressor block ............................................................................................................ 5
2.5 Ambient conditions ........................................................................................................... 5
2.6 Pressure switch setting .................................................................................................... 5
2.7 Pressure ........................................................................................................................... 6
2.8 Sound emission ................................................................................................................ 6
2.9 Motor power and speed ................................................................................................... 7
2.10 Compressor oil recommendations ................................................................................... 8
2.10.1 Compressor oil charge ........................................................................................ 8
2.11 Electrical connection ........................................................................................................ 9
2.11.1 Three-phase power supply ................................................................................. 9
2.12 Mains conditions .............................................................................................................. 10
2.12.1 Supply conditions at 400V/3/50Hz ...................................................................... 10
2.13 Machine duty cycle ........................................................................................................... 10
3 Safety and Responsibility
3.1 Basic instructions ............................................................................................................. 12
3.2 Specified Use ................................................................................................................... 12
3.3 Improper use .................................................................................................................... 12
3.4 User's Responsibilities ..................................................................................................... 13
3.4.1 Observe statutory and universally accepted regulations. ................................... 13
3.4.2 Qualified personnel ............................................................................................. 13
3.4.3 Adherence to inspection schedules and accident prevention regulations .......... 13
3.5 Dangers ............................................................................................................................ 14
3.5.1 Safely dealing with sources of danger ................................................................ 15
3.5.2 Safe machine operation ...................................................................................... 17
3.5.3 Organisational Measures .................................................................................... 19
3.5.4 Danger Areas ...................................................................................................... 19
3.6 Safety Devices ................................................................................................................. 19
3.7 Safety Signs ..................................................................................................................... 20
3.8 Information signs .............................................................................................................. 20
3.9 In emergency ................................................................................................................... 21
3.9.1 Correct fire fighting ............................................................................................. 21
3.9.2 Injury from handling compressor oil .................................................................... 21
3.10 Warranty ........................................................................................................................... 22
3.11 Environment protection .................................................................................................... 22
4 Design and Function
4.1 Outline of the machine ..................................................................................................... 23
4.1.1 Machine structure ............................................................................................... 23
4.1.2 Machine function ................................................................................................. 23
4.2 Options ............................................................................................................................. 24
4.2.1 Silenced air filter ................................................................................................. 24
4.2.2 Air filter with plastic casing .................................................................................. 24
Service Manual Reciprocating compressor

No.: 9_5851 21 E Premium D i
Contents
4.2.3 Hose reel ............................................................................................................ 24

4.3 Operating modes and control modes ............................................................................... 25
4.3.1 Machine operating modes .................................................................................. 25
4.3.2 Control modes .................................................................................................... 25
4.4 Safety devices .................................................................................................................. 25
5 Installation and Operating Conditions
5.1 Ensuring safety ................................................................................................................ 26
5.2 Installation conditions ....................................................................................................... 26
6 Installation
6.1 Ensuring safety ................................................................................................................ 27
6.2 Reporting Transport Damage ........................................................................................... 28
6.3 Fitting the antivibration mounts ........................................................................................ 28
6.4 Replacing the air filter ...................................................................................................... 28
6.5 Connecting the machine with the compressed air network .............................................. 29
6.6 Connecting the machine to the power supply .................................................................. 29
7 Initial Start-up
7.1 Ensuring safety ................................................................................................................ 30
7.2 Instructions to be observed before commissioning or re-commissioning ......................... 31
7.3 Checking installation and operating conditions ................................................................ 31
7.4 Motor overload protection ................................................................................................ 32
7.4.1 Motor protection setting by direct online starting ................................................ 32
7.5 Checking direction of rotation ........................................................................................... 32
7.6 Starting the machine for the first time .............................................................................. 32
7.7 Measuring the air receiver charging time ......................................................................... 33
7.8 Setting the air network pressure ...................................................................................... 33
7.9 Setting the filter regulator ................................................................................................. 34
8 Operation
8.1 Switching on and off ......................................................................................................... 36
9 Fault Recognition and Rectification
9.1 Basic instructions ............................................................................................................. 37
9.2 Alarms .............................................................................................................................. 37
10 Maintenance
10.1 Ensuring safety ................................................................................................................ 40
10.2 Maintenance Schedule ..................................................................................................... 41
10.2.1 Logging maintenance work ................................................................................. 41
10.2.2 Regular maintenance tasks ................................................................................ 41
10.2.3 Oil changing intervals ......................................................................................... 41
10.2.4 Regular service tasks ......................................................................................... 42
10.3 Maintaining the air cooler or fan guard ............................................................................. 42
10.3.1 Cleaning the air cooler or fan guard ................................................................... 43
10.4 Air filter maintenance ....................................................................................................... 43
10.5 Air filter (sound damping) maintenance ........................................................................... 44
10.6 Air filter (plastic housing) maintenance ............................................................................ 45
10.7 Drive motor maintenance ................................................................................................. 46
10.8 Checking the oil level ....................................................................................................... 46
10.9 Topping up the compressor oil ......................................................................................... 47
10.10 Changing the compressor oil ........................................................................................... 48
10.11 Checking the pressure relief valve ................................................................................... 49
10.11.1 Pressure relief valve in the collecting pipe .......................................................... 49
10.11.2 Air receiver pressure relief valve ........................................................................ 50
10.12 Air receiver maintenance ................................................................................................. 50

ii Premium D No.: 9_5851 21 E
Contents
10.13 Venting the machine (de-pressurising) ............................................................................ 51

10.14 Maintaining the check valve ............................................................................................. 52
10.15 Maintenance of the pressure switch unloading valve ....................................................... 53
10.16 Filter regulator maintenance ............................................................................................ 53
10.17 Cylinder head and valves ................................................................................................. 54
10.18 Documenting maintenance and service work .................................................................. 55
11 Spares, Operating Materials, Service
11.1 Note the nameplate .......................................................................................................... 56
11.2 Ordering consumable parts and operating fluids/materials .............................................. 56
11.3 Service Addresses ........................................................................................................... 57
11.4 KAESER AIR SERVICE .................................................................................................. 57
11.5 Spares for service and repair ........................................................................................... 57
12 Decommissioning, Storage and Transport
12.1 Decommissioning ............................................................................................................. 58
12.2 Packing ............................................................................................................................ 58
12.3 Storage ............................................................................................................................. 59
12.4 Transporting ..................................................................................................................... 59
12.4.1 Safety .................................................................................................................. 59
12.5 Disposal ........................................................................................................................... 59
13 Annex
13.1 Dimensional Drawing ....................................................................................................... 60
13.2 Electrical Diagram ............................................................................................................ 62

No.: 9_5851 21 E Premium D iii
Contents

iv Premium D No.: 9_5851 21 E
List of Illustrations
Fig. 1 Location of safety signs .............................................................................................................. 20

Fig. 2 Machine overview ....................................................................................................................... 23
Fig. 3 Silenced air filter ......................................................................................................................... 24
Fig. 4 Air filter with plastic casing ......................................................................................................... 24
Fig. 5 Hose reel .................................................................................................................................... 25
Fig. 6 Fitting the antivibration mounts .................................................................................................. 28
Fig. 7 Replacing the air filter ................................................................................................................. 28
Fig. 8 Compressed air connection ........................................................................................................ 29
Fig. 9 Setting the air network pressure ................................................................................................. 33
Fig. 10 Setting the filter regulator ........................................................................................................... 35
Fig. 11 Switching on and off ................................................................................................................... 36
Fig. 12 Cleaning the air cooler or fan guard ........................................................................................... 43
Fig. 13 Air filter maintenance .................................................................................................................. 44
Fig. 14 Air filter (sound damping) maintenance ...................................................................................... 45
Fig. 15 Air filter (plastic housing) maintenance ...................................................................................... 46
Fig. 16 Checking the oil level ................................................................................................................. 47
Fig. 17 Topping up the compressor oil ................................................................................................... 47
Fig. 18 Changing the compressor oil ...................................................................................................... 48
Fig. 19 Checking the collecting pipe relief valve .................................................................................... 49
Fig. 20 Checking pressure relief valve on the air receiver ..................................................................... 50
Fig. 21 Draining condensate .................................................................................................................. 51
Fig. 22 Venting the machine ................................................................................................................... 51
Fig. 23 Cleaning the check valve ........................................................................................................... 52
Fig. 24 Maintenance of the pressure switch unloading valve ................................................................. 53
Fig. 25 Cleaning the filter regulator ........................................................................................................ 54
Fig. 26 Consumable parts ...................................................................................................................... 56

No.: 9_5851 21 E Premium D v
List of Illustrations

vi Premium D No.: 9_5851 21 E
List of Tables
Tab. 1 Danger levels and their definition (personal injury) .................................................................... 1

Tab. 2 Danger levels and their definition (damage to property) ............................................................ 2
Tab. 3 Nameplate .................................................................................................................................. 4
Tab. 4 Options ....................................................................................................................................... 4
Tab. 5 Mass ........................................................................................................................................... 4
Tab. 6 Compressor block ...................................................................................................................... 5
Tab. 7 Ambient conditions ..................................................................................................................... 5
Tab. 8 Pressure switch setting .............................................................................................................. 5
Tab. 9 Air receiver pressure relief valve setting .................................................................................... 6
Tab. 10 Collecting pipe relief valve setting .............................................................................................. 6
Tab. 11 Sound pressure level .................................................................................................................. 7
Tab. 12 Power and speed ....................................................................................................................... 7
Tab. 13 Permissible starting frequency ................................................................................................... 7
Tab. 14 Compressor oil recommendations .............................................................................................. 8
Tab. 15 Compressor oil charge ............................................................................................................... 8
Tab. 16 Supply details 230V/3/50Hz ....................................................................................................... 9
Tab. 17 Supply details 400V/3/50Hz ....................................................................................................... 10
Tab. 18 Network impedance .................................................................................................................... 10
Tab. 19 Machine duty cycle ..................................................................................................................... 11
Tab. 20 Inspection intervals according to Ordinance on Industrial Safety and Health ............................ 14
Tab. 21 Danger Areas ............................................................................................................................. 19
Tab. 22 Safety Signs ............................................................................................................................... 20
Tab. 23 Information signs ........................................................................................................................ 20
Tab. 24 Re-commissioning after storage ................................................................................................. 31
Tab. 25 Checklist of installation conditions .............................................................................................. 31
Tab. 26 Air receiver charging time ........................................................................................................... 33
Tab. 27 Changing the pressure switch setting ........................................................................................ 34
Tab. 28 Alarms and remedies ................................................................................................................. 37
Tab. 29 Regular maintenance tasks ........................................................................................................ 41
Tab. 30 Oil changing intervals ................................................................................................................. 41
Tab. 31 Regular service tasks ................................................................................................................. 42
Tab. 32 Logged maintenance tasks ........................................................................................................ 55
Tab. 33 Consumable parts ...................................................................................................................... 56

No.: 9_5851 21 E Premium D vii
List of Tables

viii Premium D No.: 9_5851 21 E
1.1 Using this document

1.1 Using this document
The operating manual is a component of the product. It describes the machine as it was at the time
of first delivery after manufacture.
➤ Keep the operating manual in a safe place throughout the life of the machine.
➤ Supply any successive owner or user with this operating manual.
➤ Please insert any amendment or revision of the operating manual sent to you.
➤ Enter details from the machine nameplate and individual items of equipment in the table in
chapter 2.
1.2 Further documents

Included with this operating manual are additional documents intended to assist in the safe opera‐
tion of the machine:
■ Certificate of acceptance/operating instructions for the pressure vessel
■ Declaration of Conformity in accordance with applicable directives.
Missing documents can be requested from KAESER.

➤ Make sure all documents are complete and observe the instructions contained in them.
➤ Make sure you give the data from the nameplate when ordering documents.
1.3 Copyright
This service manual is copyright protected. Queries regarding use or duplication of the documenta‐
tion should be referred to KAESER. Correct use of information will be fully supported.
1.4 Symbols and labels

➤ Please note the symbols and labels used in this document.
1.4.1 Warnings
Warning notices indicate dangers that may result in injury when disregarded.
Warning notices indicate three levels of danger identified by the corresponding signal word:
Signal term Meaning Consequences of non-compliance
DANGER Warns of an imminent threat of danger Will result in death or severe injury
WARNING Warns of possible danger May result in death or severe injury
CAUTION Warns of a potentially dangerous situation May result in a moderate physical injury
Tab. 1 Danger levels and their definition (personal injury)
Warning notices preceding a chapter apply to the entire chapter, including all sub-sections.
Example:

No.: 9_5851 21 E Premium D 1
DANGER
These show the kind of danger and its source.
The possible consequences of ignoring a warning are shown here.
If you ignore the warning notice, the "DANGER" signal word indicates a lethal or severe in‐
jury will occur.
➤ The measures required to protect yourself from danger are shown here.
Warning notes referring to a sub-section or the subsequent action are integrated into the procedure
and numbered as an action.
Example:
1. WARNING!
The possible consequences of ignoring a warning are shown here.
If you ignore the warning notice, the "WARNING" signal word indicates that a lethal or severe
injury may occur.
➤ The measures required to protect yourself from danger are shown here.
2. Always read and comply with warning instructions.
1.4.2 Potential damage warnings

Contrary to the warnings shown above, damage warnings do not indicate a potential personal in‐
jury.
Warning notices for damages are identified by their signal term.

Signal term Meaning Consequences of non-compliance
NOTE Warns of a potentially dangerous situation Damage to property is possible
Tab. 2 Danger levels and their definition (damage to property)
Example:
NOTICE
Potential effects when ignoring the warning are indicated here.
➤ The protective measures against the damages are shown here.
➤ Carefully read and fully comply with warnings against damages.
1.4.3 Other alerts and their symbols

This symbol identifies particularly important information.

2 Premium D No.: 9_5851 21 E
Material Here you will find details on special tools, operating materials or spare parts.
Precondition Here you will find conditional requirements necessary to carry out the task.
Here conditions relevant to safety are named that will help you to avoid dangerous situations.
Option H1 ➤ This symbol denotes lists of actions comprising one stage of a task.
Operating instructions with several steps are numbered in the sequence of the operating steps.
Information relating to one option only are marked with an option code (e.g., H1 indicates that
this section applies only to machines with screw-in machine feet).
Information referring to potential problems are identified by a question mark.
The cause is named in the help text ...
➤ ... as is a solution.
This symbol identifies important information or measures regarding the protection of the envi‐
ronment.
Further information Further subjects are introduced here.

No.: 9_5851 21 E Premium D 3
2.1 Nameplate
2.1 Nameplate
The model designation and important technical information are given on the machine's nameplate.
➤ Enter here the nameplate data as a reference:
Feature Value
Reciprocating compressor
Material no.
Serial no.
Year of manufacture
Maximum working pressure
Inlet volume
Electrical connection
Synchronous speed
Rated power
Ambient temperature
Tab. 3 Nameplate
2.2 Options
The table contains a list of possible options.
➤ Enter options here as a reference.
Option Option code Available?

Silenced air filter H9
Air filter with plastic casing H10
Hose reel P2
Tab. 4 Options
2.3 Mass
The values shown are maximum values. The actual weight depends on equipment fitted.
Compressor model Air receiver size [l] Mass [kg]

Premium 200/24 24 31
Premium 250/24 24 30
Premium 250/40 40 38/45*
Premium 300/40 40 42/46*
Premium 350/40 40 56/63*
* with hose reel

4 Premium D No.: 9_5851 21 E
2.4 Compressor block
Compressor model Air receiver size [l] Mass [kg]

Premium 350/90 90 73/77*
Premium 450/40 40 65/69*
Premium 450/90 90 82/86*
Premium 660/90 90 103/107*
* with hose reel
Tab. 5 Mass
2.4 Compressor block

Compressor block type Compressor Theoretical dis‐ FAD at Number of cylin‐
model place‐ 6 bar [l/min] ders
ment [l/min]
KCC 200 Premium 200 200 115 1
KCC 250 Premium 250 250 150 1
KCC 300 Premium 300 300 175 1
KC 350 Premium 350 350 230 1
KC 400 Premium 450 450 300 2
KC 630 Premium 660 660 440 2
Tab. 6 Compressor block
2.5 Ambient conditions

Installation
Maximum altitude 1000
amsl* [m]
Permissible ambient tem‐ 5–35
perature [°C]
* Higher altitudes are permissible only after consultation with the manufacturer.
Tab. 7 Ambient conditions
2.6 Pressure switch setting

Specified pressures are factory set.
Customer-specific settings may differ.
The air receiver is permanently in a pressure band of 20%. Hence, the pressure difference
may (≙ 2.2 bar) not exceed 20%.
Characteristic Value
Cut-in pressure [bar] 7
* Minimum adjustment range: Cut-in pressure / cut-out pressure

No.: 9_5851 21 E Premium D 5
2.7 Pressure
Cut-out pressure [bar] 9
Maximum 2
pressure differen‐
tial Δp [bar]
Minimum setting 3/4
range [bar]*
* Minimum adjustment range: Cut-in pressure / cut-out pressure
Tab. 8 Pressure switch setting
2.7 Pressure
Air receiver pressure relief valve
Maximum 10
working overpres‐
sure [bar]
Pressure relief valve 11
activating pressure [bar]
Tab. 9 Air receiver pressure relief valve setting
Pressure relief valve in the collecting pipe*

Maximum 10
working overpres‐
sure [bar]
Pressure relief valve 12.5
activating pressure [bar]
* Premium 660
Tab. 10 Collecting pipe relief valve setting
2.8 Sound emission

Sound power level
■ in accordance with 2000/14/EG and ISO 3744
Emission sound pressure level

■ calculated from the measured average sound power level (directive 2000/14/EG, Sound Meas‐
uring Standard ISO 3744) according to EN ISO 11203:1995 6.2.3d at distance d = 1 m,
Q2 = Logarithmic surface ratio: dB.
EC type approval:
■ Certificate No.: OR/2551/SZ03

6 Premium D No.: 9_5851 21 E
2.9 Motor power and speed
Compressor model Sound pressure level [dB(A)] Emission sound Logarithmic sur‐
Measured Guaranteed pressure level face ratio [dB]
[dB(A)]
Premium 200/24 88 97 74 13.7
Premium 250/24 90 97 76 13.7
Premium 250/40 91 97 77 14.0
Premium 300/40 90 97 76 14.1
Premium 350/40 88 97 74 14.1
Premium 350/90 89 97 74 14.6
Premium 450/40 89 97 75 14.1
Premium 450/90 91 97 76 14.6
Premium 660/90 91 97 76 14.9
Tab. 11 Sound pressure level
2.9 Motor power and speed

➤ Read off the enclosure protection class from the motor nameplate and enter in the table.
Compressor model Compressor Rated pow‐ Synchronous Enclosure pro‐

block type er [kW] speed [rpm] tection
(50 Hz)
Premium 200 KCC 200 1.1 3000
Premium 250 KCC 250 1.2 3000
Premium 300 KCC 300 1.5 3000
Premium 350 KC 350 1.7 1500
Premium 450 KC 400 2.4 1500
Premium 660 KC 630 3.0 1500
Tab. 12 Power and speed
Permissible starting frequency
➤ The permissible starting frequency of the motor is listed in the table below:
Rated power [kW] Permissible starting frequency [1/h]

1.1 20
1.2 20
1.5 20
1.7 20
2.4 20
3.0 20
Tab. 13 Permissible starting frequency

No.: 9_5851 21 E Premium D 7
2.10 Compressor oil recommendations
2.10 Compressor oil recommendations

The standard compressor oil is SAE 5 W30 or VDL 150.
For special applications FGP oil is used and the machine carries a sticker indicating this.
Information on ordering compressor oil is found in chapter 11.
➤ Mark the oil that your compressor contains in the table below.
Standard oil Special oil

Premium 200 – Premium 660
Premium 450
Oil type SAE 5 W30 VDL 150 FGP
Field of application Standard oil for all ap‐ Standard oil for all ap‐ Specifically for ma‐
plications except in plications except in chines in applications
connection with food‐ connection with food‐ where the compressed
stuffs. stuffs. air may come into con‐
tact with foodstuff.
Maximum permissible 1000/2* 1000/1* 1000/2*
oil change interval in
operating hours/years.
Oil contained in my
compressor
* Cool to moderate ambient temperatures, low humidity, low to average duty cycle.
Tab. 14 Compressor oil recommendations
2.10.1 Compressor oil charge

Compressor block type Total charge [litres] Topping up volume [litres]
(minimum–maximum)
KCC 200 0.13 0.05
KCC 250 0.13 0.05
KCC 300 0.13 0.05
KC 350 0.2 0.1
KC 400 1.0 0.2
KC 630 1.2 0.22
Tab. 15 Compressor oil charge

8 Premium D No.: 9_5851 21 E
2.11 Electrical connection
2.11 Electrical connection

Basic requirements
The machine is designed in accordance with the conditions for an electrical power supply specified
in EN 60204-1 (IEC 60204-1) section 4.3.
If no other conditions are specified by the operator, the thresholds described in this standard must
be adhered to.
It is recommended that the user and the supplier reach an agreement on the basis of EN 60204-1,
Annex B.
Check and adjust for other deployment conditions before commissioning.
If the machine is supplied with a mains cable and a plug, the power socket may be fused at
the nominal current of the plug device.
2.11.1 Three-phase power supply

For electrical connection of the machine, a symmetric three-phase supply is necessary.
In a symmetrical three-phase supply, the phase angles and voltages are equal.
This machine may only be supplied from an earthed TN or TT three-phase supply in which the
neutral point is earthed.
Connection to an IT supply is not permitted without taking further measures (earth leak detection,
etc.).
Further information When connecting to a European 400 V/3/50 Hz rated voltage the requirements in chapter 2.12 are
also to be observed.
See electrical diagram in 13.2.
2.11.1.1 Power supply specifications
Conductor cross-sections (copper multicore) and fusing (fuses, class gG) are given according to
DIN VDE 0100–430 (IEC 60364-4-43 and IEC 60364-4-473) and
DIN VDE 0298-4 (HD 384.5.523 S2) for ambient temperatures from 30 °C.
➤ For other application conditions, check conductor diameters and change accordingly.
Other conditions would include, for example:

■ Higher temperature
■ Cable length >50 m
Rated voltage: 230V±10%/3/50Hz
Compressor model Backup fuse [A] Supply cable [mm2] Current drawn [A]
Premium 200 6 4 x 1.5 3.8
Premium 250 10 4 x 1.5 4.5
Premium 300 16 4 x 2.5 5.8
Premium 350 10 4 x 2.5 6.9
Premium 450 16 4 x 2.5 9.9
Premium 660 25 4x4 11.8
Tab. 16 Supply details 230V/3/50Hz

No.: 9_5851 21 E Premium D 9
2.12 Mains conditions
Rated voltage: 400V±10%/3/50Hz
Compressor model Backup fuse [A] Supply cable [mm2] Current drawn [A]
Premium 200 6 4 x 1.5 2.2
Premium 250 6 4 x 1.5 2.6
Premium 300 10 4 x 1.5 3.35
Premium 350 6 4 x 1.5 4.0
Premium 450 10 4 x 1.5 5.7
Premium 660 16 4 x 2.5 6.8
Tab. 17 Supply details 400V/3/50Hz
2.12 Mains conditions

The machines listed in the table below are intended for use in changing locations.
No interference with other devices is to be expected with network impedance less than Zmax
[Ohm]. In general, the maximum permissible network impedance will not be exceeded if the ma‐
chine is supplied at the transfer point with a rated current of Iequiv .
2.12.1 Supply conditions at 400V/3/50Hz

Compressor model Maximal permissible Highest permissible Rated current
motor starts [1/h]* system impe‐ Iequiv. [A]
dance Zmax [Ω]**
Premium 200 20 *** ***
Premium 250 20 *** ***
Premium 300 20 *** ***
Premium 350 20 *** ***
Premium 450 20 *** ***
Premium 660 20 0.199 40
Exceeding the maximal permissible starts must be discussed with the manufacturer.
** The data are relative to the sum of impedances in external and neutral lines.
*** No specification required. Compliance with DIN EN 61000-3-3 is ensured according to the con‐
ditions applied.
Tab. 18 Network impedance
2.13 Machine duty cycle

Calculating the cycling period
Cycling time = time under LOAD + time at standstill
Calculating the duty cycle:
time at LOAD
Duty cycle [%] = x 100
time at LOAD + standstill period
Example:

10 Premium D No.: 9_5851 21 E
2.13 Machine duty cycle
12 minutes
x 100 % = 60 %
20 minutes
The following values are valid for:

■ Ambient temperature 20 °C
■ 30 % relative humidity
■ 1013 mbar air pressure
Compressor model Permissible duty cycle [%] Cycle time [min]

Premium 200 ≤ 70 3–20
Premium 250 ≤ 70 3–20
Premium 300 ≤ 70 3–20
Premium 350 ≤ 70 3–30
Premium 450 ≤ 70 3–30
Premium 660 ≤ 70 3–30
Tab. 19 Machine duty cycle

No.: 9_5851 21 E Premium D 11
3.1 Basic instructions

The machine is manufactured to the latest engineering standards and acknowledged safety regula‐
tions. Nevertheless, dangers can arise through its operation:
■ danger to life and limb of the operator or third parties,
■ impairments to the machine and other material assets.
Disregard of warning or safety instructions can cause serious injuries!
➤ Use this machine only if it is in a technically perfect condition and only for the purpose for
which it is intended; observe all safety measures and the instructions in the service manual.
➤ Immediately rectify (have rectified) any faults that could be detrimental to safety.
3.2 Specified Use

The machine is intended solely for generating compressed air for industrial use. Any other use is
considered incorrect. The manufacturer is not liable for any damages that may result therefrom.
The user alone is liable for any risks incurred.
➤ Keep to the specifications listed in this service manual.
➤ Operate the machine only within its performance limits and under the permitted ambient condi‐
tions.
➤ Do not use compressed air for breathing purposes unless it is specifically treated.
➤ Do not use compressed for any application that will bring it into direct contact with foodstuffs
unless it is specifically treated.
3.3 Improper use

➤ Never direct compressed air at persons or animals.
➤ Do not touch hot components during operation or after shutdown. Wait until they have cooled
before touching!
These components include, for example, cylinder heads, compressed air lines, coolers, motors
and machine heating systems.
➤ Always switch off the compressor and disconnect it from the mains power supply when not in
use.
➤ In order to prevent injury, keep children away from the compressor work area and its associ‐
ated compressed air equipment.
➤ Children are not allowed to operate the compressor.
➤ Use hot cooling air for heating purposes only if there is no risk to the health of humans or ani‐
mals. If necessary, hot cooling air should be treated by suitable means.
➤ Do not allow the machine to take in toxic, acidic, flammable or explosive gases or vapours.
➤ Do not operate the machine in areas in which specific requirements with regard to explosion
protection are in force.

12 Premium D No.: 9_5851 21 E
3.4 User's Responsibilities
3.4 User's Responsibilities

3.4.1 Observe statutory and universally accepted regulations.
This is, for example, nationally applied European directives and/or valid national legislation, safety
and accident prevention regulations.
➤ Observe relevant statutory and accepted regulations during installation, operation and mainte‐
nance of the machine.
3.4.2 Qualified personnel

These are people who, by virtue of their training, knowledge and experience as well as their knowl‐
edge of relevant regulations can assess the work to be done and recognise the possible dangers
involved.
Authorised operators possess the following qualifications:

■ are of legal age,
■ are conversant with and adhere to the safety instructions and sections of the service manual
relevant to operation,
■ have received adequate training and authorisation to operate electrical and compressed air de‐
vices.
Authorised installation and maintenance personnel have the following qualifications:

■ are of legal age,
■ have read, are conversant with and adhere to the safety instructions and sections of the serv‐
ice manual applicable to installation and maintenance,
■ are fully conversant with the safety concepts and regulations of electrical and compressed air
engineering,
■ are able to recognise the possible dangers of electrical and compressed air devices and take
appropriate measures to safeguard persons and property,
■ have received adequate training and authorisation for the safe installation and maintenance on
this equipment.
➤ Ensure that operating, installation and maintenance personnel are qualified and authorised to
carry out their tasks.
3.4.3 Adherence to inspection schedules and accident prevention regulations

The machine is subject to local inspection schedules.
Examples of German operation
➤ Recurring inspections according to BGR 500, chapter 2.11.

The user must ensure that, for machines with motor power above 0.5 kW, safety devices are
checked for function as required or at least annually.

No.: 9_5851 21 E Premium D 13
3.5 Dangers
➤ Keep to inspection intervals in accordance with the Ordinance on Industrial Safety and Health
with maximum intervals as laid down in §15.
The inspection intervals are laid down in the technical specification for the air receiver. In‐
spection intervals are dependent on the pressure/volume product of the air receiver, i.e. max
permissible pressure (PS) in bar, times the receiver volume (V) in litres.
Example: volume V = 90 litres, max. permissible pressure PS = 11 bar; pressure/volume
product = 990.
Inspection Inspection interval Inspecting authority

Installation and equip‐ Before commissioning if pressure Competent person
ment inspection PS x volume V ≤ 200 (e. g. KAESER Service Techni‐
cian)
Compressors with type approval in‐ Competent person
spection (Ordinance on Industrial (e. g. KAESER Service Techni‐
Safety and Health, annex 5 no. 25) cian)
PS x V ≤ 1000
Before commissioning if Approved supervisory body
PS x V > 200
Internal inspection Every 5 years after installation or the Competent person
last inspection if (e. g. KAESER Service Techni‐
PS x V ≤ 1000 cian)
Every 5 years after installation or the Approved supervisory body
last inspection if
PS x V > 1000
Strength test Every 10 years after installation or the Competent person
last inspection if (e. g. KAESER Service Techni‐
PS x V ≤ 1000 cian)
Every 10 years after installation or the Approved supervisory body
last inspection if
PS x V > 1000
* The inspection interval is determined by the user in consultation with the approved supervisory
body. The responsible body is to be notified not later than 6 months after the inspection carried
out before commissioning (if pressure x volume V > 1000). Intervals given are the maximum in
each case.
Tab. 20 Inspection intervals according to Ordinance on Industrial Safety and Health
3.5 Dangers
Basic Information
Information concerning the various forms of danger that can arise during machine operation are
found here.
Basic safety instructions are found in this service manual at the beginning of each chapter in the
section entitled 'Safety'.
Warning instructions are found before a potentially dangerous task.

14 Premium D No.: 9_5851 21 E
3.5 Dangers
3.5.1 Safely dealing with sources of danger

Information concerning the various forms of danger that can arise during machine operation are
found here.
Electricity
Touching voltage carrying components can result in electric shocks, burns or death.
➤ Allow only qualified and authorized electricians or trained personnel under the supervision of a
qualified and authorized electrician to carry out work on electrical equipment according to elec‐
trical engineering regulations.
➤ Before commissioning or re-commissioning the machine, the user must make sure there is ad‐
equate protection against electric shock from direct or indirect contact.
➤ Before starting any work on electrical equipment:
Switch off and lock out the power supply isolator and check that no voltage is present.
➤ Switch off any external power sources.
These could be connections to floating relay contacts or the electrical machine heating, for ex‐
ample.
➤ Use fuses corresponding to machine power.
➤ Check regularly that all electrical connections are tight and in proper condition.
Forces of compression
Compressed air is contained energy. Uncontrolled release of this energy can cause serious injury
or death. The following information concerns work on components that could be under pressure.
➤ Close shut-off valves or otherwise isolate the machine from the distribution network to ensure
that no compressed air can flow back into the machine.
➤ De-pressurise all pressurised components and enclosures.
➤ Do not carry out welding, heat treatment or mechanical modifications to pressurized compo‐
nents (e.g. pipes and vessels) as this influences the component's resistance to pressure.
The safety of the machine is then no longer ensured.
Compressed air quality
The composition of the compressed air must be suitable for the actual application in order to pre‐
clude health and life-threatening dangers.
➤ Use appropriate systems for air treatment before using the compressed air from this machine
as breathing air and/or for the processing of foodstuffs.
➤ Use foodstuff-compatible cooling oil whenever compressed air is to come into contact with
foodstuffs.
Spring forces
Springs under tension or compression represent contained energy. Uncontrolled release of this en‐
ergy can cause serious injury or death.
Solenoid valves and check valves are spring-loaded.
➤ Do not open or dismantle any valves.
Rotating components
Touching the fan while the machine is switched on can result in serious injury.

No.: 9_5851 21 E Premium D 15
3.5 Dangers
➤ Do not open the enclosure while the machine is switched on.

➤ Switch off and lock out the power supply disconnecting device and verify the absence of any
voltage.
➤ Wear close-fitting clothes and a hair net if necessary.
➤ Make sure all covers and safety guards are in place and secured before re-starting.
Temperature
High temperatures are generated during compression. Touching hot components may cause inju‐
ries.
➤ Avoid contact with hot components.
These include, for example, compressor blocks, compressed air pipes, coolers, motors and
machine heaters.
➤ Wear protective clothing.
➤ If welding is carried out on or near the machine, take adequate measures to prevent sparks or
heat from igniting oil vapours or parts of the machine.
Noise
The enclosure absorbs the machine noise to a tolerable level. This function will be effective only if
the enclosure is closed.
➤ Operate the machine only with intact sound insulation.
➤ Wear hearing protection if necessary.
The pressure relief valve blowing off can be particularly loud.
Operating fluids/materials
The used operating fluids and materials can cause adverse health effects. Suitable safety meas‐
ures must be taken in order to prevent injuries.
➤ Strictly forbid fire, open flame and smoking.
➤ Follow safety regulations when dealing with oils, lubricants and chemical substances.
➤ Avoid contact with skin and eyes.
➤ Do not inhale oil mist and vapours.
➤ Do not eat or drink while handling cooling and lubricating fluids.
➤ Keep suitable fire extinguishing agents ready for use.
➤ Use only KAESER approved operating materials.
Unsuitable spare parts
Unsuitable spare parts compromise the safety of the machine.

➤ Use only spare parts approved by the manufacturer for use in this machine.
➤ Use only genuine KAESER pressure components.
Conversion or modification of the machine
Modifications, additions to and conversions of the machine can result in unpredictable dangers.
➤ Do not convert or modify the machine!
➤ Obtain written approval by the manufacturer prior to any technical modification or expansion of
the machine.

16 Premium D No.: 9_5851 21 E
3.5 Dangers
Extending or modifying the compressed air system
If dimensioned appropriately, pressure relief valves reliably prevent an impermissible rise in pres‐
sure. New dangers may arise if you modify or extend the compressed air station.
➤ When extending or modifying the compressed air system.
Check the blow-off capacity of pressure relief valves on air receivers and compressed air lines
before installing a new machine.
➤ If the blow-off capacity is insufficient:
Install pressure relief valves with larger blow-off capacity.
3.5.2 Safe machine operation

The following is information supporting you in the safe handling of the machine during individual
product life phases.
Personal protective equipment
When working on the machine you may be exposed to dangers that can result in accidents with
severe adverse health effects.
➤ Wear protective clothing as necessary.
Suitable protective clothing (examples):

■ Safety work wear
■ Protective gloves
■ Safety boots
■ Eye protection
■ Ear protection
Transport
The mass and size of the machine require safety measures during its transport to prevent acci‐
dents.
➤ Use suitable lifting gear that conforms to local safety regulations.
➤ Allow transportation only by personnel trained in the safe movement of loads.
➤ Attach lifting gear only to suitable lifting points.
➤ Be aware of the centre of gravity to avoid tipping.
➤ Make sure the danger zone is clear of personnel.
➤ Do not step onto machine components to climb up the machine.
Assembly
➤ Use only electrical cables that are suitable and approved for the surroundings and electrical
loads applied.
➤ Never dismantle compressed air pipes until they are fully vented.
➤ Only use pressure lines that are suitable and approved for the maximum working pressure and
the intended medium.
➤ Do not allow connection pipes to be placed under mechanical stress.
➤ Do not induce any forces into the machine via the connections, so that the compressive forces
must be balanced by bracing.

No.: 9_5851 21 E Premium D 17
3.5 Dangers
Installation
A suitable installation location for the machine prevents accidents and faults.
➤ Install the machine in a suitable compressor room.
➤ Ensure sufficient and suitable lighting such that the display can be read and work carried out
comfortably and safely.
➤ Ensure accessibility so that all work on the machine can be carried out without danger or hin‐
drance.
➤ If installed outdoors, the machine must be protected from frost, direct sunlight, dust, rain and
splashing water.
➤ Do not operate in areas in which specific requirements with regard to explosion protection are
in force.
For instance, the requirements of ATEX directive 94/9/EC "Equipment and Protective Systems
intended for use in Potentially Explosive Atmospheres".
➤ Ensure adequate ventilation.
➤ Place the machine in such a manner that the working conditions in its environment are not im‐
paired.
➤ Comply with limit values for ambient temperature and humidity.
➤ The intake air must not contain any damaging contaminants,
Damaging contaminants are for instance: explosive or chemically instable gases and vapours,
acid or base forming substances such as ammonia, chlorine or hydrogen sulfide.
➤ Do not position the machine in the warm exhaust air flow from other machines.
Commissioning, operation and maintenance
During commissioning, operation and maintenance you may be exposed to dangers resulting from,
e.g., electricity, pressure and temperature. Careless actions can cause accidents with severe ad‐
verse effects for your health.
➤ Allow maintenance work to be carried out only by authorised personnel.
➤ Wear close-fitting, flame-resistant clothing. Wear protective clothing as necessary.
➤ Switch off and lock out the power supply disconnecting (isolating) device and check that no
voltage is present.
➤ Check that there is no voltage on potential-free contacts.
➤ Close shut-off valves or otherwise isolate the machine from the compressed air network to en‐
sure that no compressed air can flow back into the machine.
➤ De-pressurise all pressurised components and enclosures.
➤ Allow the machine to cool down.
➤ Do not open the cabinet while the machine is switched on.
➤ Use only spare parts approved by KAESER for use in this machine.
➤ Carry out regular inspections:
for visible damages,
of the safety installation,
of the mains power switch,
of parts needing monitoring.
➤ Pay particular attention to cleanliness during all maintenance and repair work. Cover compo‐
nents and openings with clean cloths, paper or tape to keep them clean.

18 Premium D No.: 9_5851 21 E
3.6 Safety Devices
➤ Do not leave any loose components, tools or cleaning rags on or in the machine.
➤ Components removed from the machine can still be dangerous.
Do not attempt to open or destroy any components taken from the machine.
De-commissioning, storage and disposal
Improper handling of old operating fluids and components represent a danger for the environment.
➤ Drain off fluids and dispose of them according to environmental regulations.
These include, for example, lubricating oil and compressor oil.
➤ Dispose of the machine in accordance with local environmental regulations.
3.5.3 Organisational Measures

➤ Designate personnel and their responsibilities.
➤ Give clear instructions on reporting faults and damage to the machine.
➤ Give instructions on fire reporting and fire-fighting measures.
3.5.4 Danger Areas

The table gives information on the areas dangerous to personnel.
Only authorised personnel may enter these areas.
Activity Danger area Authorised personnel

Transport Within a 1 m radius of the machine. Installation personnel for transport
preparation.
No personnel during transport.
Beneath the lifted machine. No personnel!
Installation Within the machine. Installation personnel
Within 1 m radius of the machine and its sup‐
ply cables.
Operation Within a 1 m radius of the machine. Operating personnel
Maintenance Within the machine. Maintenance personnel
Within a 1 m radius of the machine.
Tab. 21 Danger Areas
3.6 Safety Devices

Various safety devices ensure safe working with the machine.
➤ Do not change, bypass or disable safety devices.
➤ Check safety devices for correct function regularly.
➤ Do not remove or obliterate labels and notices.
➤ Ensure that labels and notices are clearly legible.
Further information More information on safety devices is contained in chapter4, section 4.4.

No.: 9_5851 21 E Premium D 19
3.7 Safety Signs
3.7 Safety Signs

The diagram shows the positions of safety signs on the machine. The table lists the various safety
signs used and their meanings.
Fig. 1 Location of safety signs
Item Sign Meaning

1 Danger of fatal injury from electric shock!
➤ Before starting any work on electrical equipment:
Switch off and lock out the power supply disconnecting device and check that
no voltage is present.
2 Hot surface!
Risk of burns caused by contact with hot components
➤ Do not touch the surface.
➤ Wear long-sleeved garments (not synthetics such as polyester) and protective
gloves.
3 Risk of injury caused by an automatic machine start!
➤ Switch off and lock out the power supply disconnecting device and check that
no voltage is present before opening any machine enclosure or guard.
Tab. 22 Safety Signs
3.8 Information signs

The table lists the various information signs used and their meanings.
Sign Meaning
Take heed of safety instructions and the service manual.

20 Premium D No.: 9_5851 21 E
3.9 In emergency
Sign Meaning
Maintain the air filter regularly.
Drain the condensate daily.

If automatic condensate drainage is fitted, check the function at regular intervals.
Check the oil level regularly and change the oil at the correct intervals.
Tab. 23 Information signs
3.9 In emergency
3.9.1 Correct fire fighting
Suitable measures
Calm and prudent action can safe lives in the event of a fire.
➤ Keep calm.
➤ Give the alarm.
➤ Shut off supply lines if possible.
Power supply disconnecting device (all phases)
Cooling water (if present)
➤ Warn and move endangered personnel to safety.
➤ Help incapacitated persons.
➤ Close the doors.
➤ When trained accordingly: Attempt to extinguish the fire.
Extinguishing substances
➤ Suitable extinguishing media:

Foam
Carbon dioxide
Sand or soil
➤ Unsuitable extinguishing media:
Strong jet of water
3.9.2 Injury from handling compressor oil

Eye contact:
Compressor oil can cause irritation.

➤ Rinse open eyes thoroughly for a few minutes under running water.
➤ Seek medical help if irritation persists.
Skin contact:
Compressor oil may irritate after prolonged contact.

No.: 9_5851 21 E Premium D 21
3.10 Warranty
➤ Wash thoroughly with skin cleaner, then with soap and water.
➤ Contaminated clothing should be dry-cleaned before reuse.
Inhalation:
Oil mist may make breathing difficult.

➤ Clear air passages of oil mist.
➤ Seek medical help if difficulty with respiration continues.
Ingestion
➤ Wash out the mouth immediately.

➤ Do not induce vomiting.
➤ Seek medical aid.
3.10 Warranty
This service manual contains no independent warranty commitment. Our general terms and condi‐
tions apply with regard to warranty.
A condition of our warranty is that the machine is used solely for the purpose for which it is inten‐
ded and under the conditions specified.
Due to the multitude applications for which the machine is suitable the obligation lies with the user
to determine its suitability for his specific application.
Furthermore, we accept no warranty obligation for:

■ the use of unsuitable parts or operating materials,
■ un-authorised modifications,
■ incorrect maintenance,
■ incorrect repair.
Correct maintenance and repair includes the use of genuine KAESER spare parts and operating
materials.
➤ Obtain confirmation from KAESER that your specific operating conditions are suitable.
3.11 Environment protection

The operation of this machine may cause dangers for the environment.
➤ Do not allow compressor oil to escape to the environment or into the waste water system.
➤ Store and dispose of operating materials and replaced parts in accordance with local environ‐
ment protection regulations.
➤ Observe national regulations.
This applies particularly to parts contaminated with compressor oil.

22 Premium D No.: 9_5851 21 E
4.1 Outline of the machine

4.1 Outline of the machine
4.1.1 Machine structure
Fig. 2 Machine overview

1 Air filter 12 Compressed air connection
2 Compressor block 12a Connection to the pressure regulator
2a One cylinder 12b Connection the the hose reel*
2b Two cylinder 13 Condensate drain tap
3 Check valve 14 Arrow showing direction of rotation
4 Air receiver 15 Pressure relief valve
5 Air receiver pressure relief valve in the collecting pipe
6 Pressure switch 16 Pressure regulator
7 Electric motor 17 Working pressure gauge
8 Air receiver pressure gauge 18 Hose Reel*
9 Oil sight glass 19 Air pipe*
10 Oil filler port 20 Air cooler*
11 Oil drain plug 21 Fan with cowl*
* machine-dependent
4.1.2 Machine function

Atmospheric air is drawn through a filter into the compression chamber of the block. The air is
drawn in during the downward stroke of the piston. It is compressed during the upward stroke.
The compressed air flows through the air pipe or cooler, giving up most of its heat, then via the
check valve into the air receiver. The check valve prevents reverse flow of compressed air from the
air receiver to the compressor block.

No.: 9_5851 21 E Premium D 23
4.2 Options
4.2 Options
The options available for your machine are described below.
4.2.1 Option H9
Silenced air filter
The air filter reduces the noise level of the machine. It also cleans the inlet air.
Fig. 3 Silenced air filter

1 Air filter cartridge
4.2.2 Option H10

Air filter with plastic casing
This air filter is suitable for unfavourable ambient conditions. It also cleans the inlet air.
Fig. 4 Air filter with plastic casing

1 Air filter element
4.2.3 Option P2
Hose reel
The machine is fitted with a hose reel inclusive air hose. This makes possible the connection of
several air consumers.

24 Premium D No.: 9_5851 21 E
4.3 Operating modes and control modes
Fig. 5 Hose reel

1 Hose reel
2 Compressed air hose
4.3 Operating modes and control modes

4.3.1 Machine operating modes
There are two operating modes:
■ LOAD
The airend delivers compressed air.
The compressor motor runs under full load.
■ READY
No air is compressed. A check valve prevents compressed air flowing back into the compres‐
sor block. The compressor block is vented.
The drive motor is stopped.
4.3.2 Control modes

■ Pressure switch:
According to the set switching points, the pressure switch toggles the machine between oper‐
ating modes LOAD and READY.
4.4 Safety devices

The following safety devices are provided and may not be modified in any way.
Pressure relief valve
The pressure relief valve protects the machine from excessive pressure. It is factory set.
Check valve
The check valve prevents the flow of compressed air from the air receiver back to the compressor
block when the machine is stopped.
Enclosures and covers
Enclosures and covers over moving parts and electrical connections protect against accidental
contact.

No.: 9_5851 21 E Premium D 25
5.1 Ensuring safety

5.1 Ensuring safety
The conditions in which the machine is installed and operated have a decisive effect on safety.
Warning instructions are located before a potentially dangerous task.
Disregard of warning instructions can cause serious injuries!
Please take note of all safety instructions
Disregard of safety notes can cause unforeseeable dangers!

➤ Strictly forbid fire, open flame and smoking.
➤ If welding is carried out on or near the machine, take adequate measures to prevent sparks or
heat from igniting oil vapours or parts of the machine.
➤ Do not store inflammable material in the vicinity of the machine.
➤ The machine is not explosion-proof!
Do not operate in areas in which specific requirements with regard to explosion protection are
in force.
For instance, the requirements of ATEX directive 94/9/EC "Equipment and Protective Systems
intended for use in Potentially Explosive Atmospheres".
➤ Ensure sufficient and suitable lighting such that the display can be read and work carried out
comfortably and safely.
➤ Ensure that required ambient conditions are maintained.
Required ambient conditions may be:

■ Maintain ambient temperature and humidity
■ Ensure the appropriate composition of the air within the machine room:
─ clean with no damaging contaminants (e.g., dust, fibres, fine sand)
─ free of explosive or chemically unstable gases or vapours
─ free of acid/alkaline forming substances, particularly ammonia, chlorine or hydrogen sulfide.
5.2 Installation conditions

Precondition The floor must be level, firm and capable of bearing the mass of the machine.
➤ If installed outdoors, the machine must be protected from frost, direct sunlight, dust and rain.
➤ Ensure adequate lighting so that all work on the machine can be carried out without danger or
hindrance.

26 Premium D No.: 9_5851 21 E
6 Installation
6.1 Ensuring safety
6 Installation
6.1 Ensuring safety
Follow the instructions below for safe installation.
Complying with safety notes

➤ Follow the instructions in chapter 3 'Safety and Responsibility'.
➤ Installation work may only be carried out by authorised personnel.
➤ Make sure that no one is working on the machine.
➤ Ensure that all service doors and panels are locked.
When working on live components
➤ Work on electrical equipment may only be carried out by authorised electricians.
voltage is present.
When working on the compressed air system
or death. The following safety concerns relate to any work on components that could be under
pressure.
➤ Isolate the machine from the air main by closing the user's shut-off valves.
➤ Vent all pressurized components and enclosures.
➤ Verify the absence of pressure using a suitable measuring device (pressure gauge).
When working on the drive system
voltage is present.
Further information Details of authorised personnel are found in chapter 3.4.2.

Details of dangers and their avoidance are found in chapter 3.5.

No.: 9_5851 21 E Premium D 27
6 Installation
6.2 Reporting Transport Damage
6.2 Reporting Transport Damage

1. Check the machine for visible and hidden transport damage.
2. Inform the carrier and the manufacturer in writing of any damage without delay.
6.3 Fitting the antivibration mounts

Antivibration mounts appropriate to the machine are delivered with the machine but not fitted.
CAUTION
There is a danger of tilting because of the high centre of gravity and mass of the machine.
➤ Use slings to lift the machine.
Fig. 6 Fitting the antivibration mounts

1 Antivibration mount
2 Hexagonal nut
➤ Remove the wooden frame from the air receiver feet.

➤ Secure the antivibration mounts to the feet with hexagon nuts.
6.4 Replacing the air filter

➤ Mount the air filter before commissioning.
The inlet opening in the filter must face downwards.
Fig. 7 Replacing the air filter

1 Air filter
➤ Fit the supplied air filter (depending on machine).
Result The machine is ready for operation.

28 Premium D No.: 9_5851 21 E
6 Installation
6.5 Connecting the machine with the compressed air network
6.5 Connecting the machine with the compressed air network

Precondition The compressed air system is vented completely to atmospheric pressure.
Verify the absence of pressure using a suitable measuring device (pressure gauge).
Fig. 8 Compressed air connection

1 Compressed air connection
1a Connection to the pressure regulator
1b Connection to the compressed air hose
➤ Make the connection to the air main by a flexible pressure line.

In addition, on versions with a hose reel the air connection can be made to the compressed
air hose.
6.6 Connecting the machine to the power supply

Machines with a total power rating up to 3 kW and rated current up to 16 amps may be plugged
into the mains supply.
Precondition The power supply is switched off,

the device is locked off,
the absence of any voltage has been verified.
1. Carry out safety measures as stipulated in relevant regulations (IEC 364, for example or
DIN VDE 0100) and in national accident prevention regulations (BGV A3 in Germany). Also ob‐
serve the regulations of the local power utility company.
2. Test the overcurrent protection cut-out to ensure that the time it takes to disconnect in re‐
sponse to a fault is within the permitted limit.
3. Select supply cable conductor cross-sections and fusing in accordance with local regulations.
4. DANGER!
Danger of fatal injury from electric shock!
➤ Switch off and lock out the power supply isolating device and check that no voltage is
present.
5. Connect the machine to the power supply.

No.: 9_5851 21 E Premium D 29
7 Initial Start-up
7.1 Ensuring safety
7 Initial Start-up
7.1 Ensuring safety

➤ Installation work may only be carried out by authorised personnel.
voltage is present.
pressure.
Touching the fan while the machine is running can result in serious injury.
voltage is present.


30 Premium D No.: 9_5851 21 E
7 Initial Start-up
7.2 Instructions to be observed before commissioning or re-commissioning
7.2 Instructions to be observed before commissioning or re-commis‐

sioning
Incorrect or improper commissioning can cause injury to persons and damage to the machine.
➤ Commissioning may only be carried out by authorized installation and service personnel who
have been trained on this machine.
Special measures for re-commissioning after storage
Storage period Remedy

longer than:
12 months ➤ Change the compressor oil.
➤ Have the motor bearings checked by an authorized KAESER Service
Technician.
36 months ➤ Have the overall technical condition checked by an authorized
KAESER Service Technician.
Tab. 24 Re-commissioning after storage
7.3 Checking installation and operating conditions

➤ Check and confirm all the items in the checklist before commissioning the machine.
To be checked see Confirmed?

chapter
➤ Are the operators fully conversant with safety regulations? –
➤ Have all the positioning conditions been fulfilled? 5
➤ Does the rated voltage conform to the specifications on the name‐ 2.1
plate?
➤ Are the power supply cable conductor cross-sections and fuse rat‐ 2.11
ings adequate?
➤ Have all electrical connections been checked for tightness? –
➤ Has the inspection been repeated after 50 operating hours following
the initial commissioning?
➤ The supplied air filter (depending on machine) is fitted? 6.4
➤ Is the connection to the air network made with a flexible hose? 6.5
➤ Sufficient oil in the crankcase? 10.8
(oil in the sight gauge red zone)
➤ The oil must be changed after 50 operating hours
➤ Motor protection device adjusted correctly with regard to the engine 7.4
power?
Tab. 25 Checklist of installation conditions

No.: 9_5851 21 E Premium D 31
7 Initial Start-up
7.4 Motor overload protection
7.4 Motor overload protection

The machine should only be operated with a correctly adjusted motor protection device to protect
the motor from overloading.
A motor overload protection switch that is set too high provides no protection. Incorrect setting can
lead to irreparable motor damage.
7.4.1 Motor protection setting by direct online starting

The machine starts directly and is controlled by a pressure switch. The pressure switch switches
the machine on and off as necessary to hold pressure within the set limits.
The overload protection device setting can be 10 % higher than the rated motor current to
prevent it from being triggered by voltage fluctuations, temperature influences or component
tolerances.
1. Read the rated motor current from the nameplate and calculate the correct protection setting.
2. Check the motor protection setting.
3. Adjust the protection setting, if necessary.
4. Switch on the compressor at the pressure switch.
The machine is shut down by the motor overload protection switch?
➤ Allow the motor to cool down.
➤ Switch the machine on again.
Further information See chapter 8.
7.5 Checking direction of rotation

The machine is designed for three-phase connection with right phase rotation.
Ideally, the direction of phase rotation should be measured with a phase sequence meter. Alterna‐
tively, start the machine very briefly and observe the direction of rotation of the motor cooling fan.
1. Check the direction of phase rotation with a phase sequence meter.
2. If the direction is incorrect, reverse supply phases L1 and L2.
You have no phase sequence meter?
➤ Switch the machine on and off again the moment the drive motor begins to turn.
➤ Check the direction of rotation against the direction arrow.
➤ If the direction is incorrect, reverse L1 and L2.
Further information Fig. 2 shows the location of the direction arrow.
7.6 Starting the machine for the first time

Precondition No personnel are working on the machine.
➤ Switch on the mains isolating device and the pressure switch.

The machine switches to LOAD and delivers compressed air.

32 Premium D No.: 9_5851 21 E
7 Initial Start-up
7.7 Measuring the air receiver charging time
➤ Watch for any faults occurring in the first hour of operation.

Carry out the following tasks after the first 50 operating hours:
➤ Check that all electrical connections are secure.
➤ Change the compressor oil.
7.7 Measuring the air receiver charging time

Measuring the time the compressor takes to fill the air receiver when new can be useful in checking
the machine's performance at a later date.
Precondition Machine at operating temperature.
1. Disconnect all air consumers.

2. Switch on the power supply isolating device.
3. Measure the air receiver charging time.
4. Enter the charging time and machine model in the table.
Machine model Receiver charging time from 3 – 8 bar [min/s]
Tab. 26 Air receiver charging time
7.8 Setting the air network pressure

The network pressure (working pressure) is set at the factory.
A pressure adjustment is possible to suit individual operating conditions.
The pressure setting can only be adjusted if a pressure switch under pressure is fitted.
Maximum pressure differential: 20 % (≙ 2.2 bar) of the maximum operating pressure of the
air receiver.
Fig. 9 Setting the air network pressure

1 Canopy 4 Pressure differential adjusting screw
2 Screw 5 «ON/OFF» switch at direct online starting
3 Adjusting screw for upper pressure(cut-out
pressure)

No.: 9_5851 21 E Premium D 33
7 Initial Start-up
7.9 Setting the filter regulator
1. DANGER!
Electric shock!
Contact with live components can cause serious injury or death.
➤ Switch off and lock out the power supply disconnecting device and check that no voltage
is present.
➤ Work with caution.
2. Remove the screws securing the cover.
3. Remove the cover.
4. WARNING!
Compressed air!
➤ Compressed air and devices under pressure can injure or cause death if the contained en‐
ergy is released suddenly.
➤ Do not loosen or open any component that is still under pressure.
5. Adjust the pressure switch setting according to the table.
Adjusting the setting Task

Cut-out pressure is to be increased. ➤ Turn the adjusting screw 3 clockwise (di‐
rection: +).
Cut-out pressure is to be decreased. ➤ Turn the adjusting screw 3 anticlockwise
(direction: −).
The pressure differential between cut-in and cut- ➤ Turn the adjusting screw 4 clockwise (di‐
out pressure is to be increased. rection: +).
The pressure differential between cut-in and cut- ➤ Turn the adjusting screw 4 anticlockwise
out pressure is to be decreased. (direction: −).
Tab. 27 Changing the pressure switch setting
6. Replace the cover.

The motor starting frequency is to be reduced?
➤ Increase the difference between cut-in and cut-out pressure.
➤ Add a larger air receiver downstream to increase buffer capacity.
Further information The duty cycle of the machine is given in chapter 2.13.
See table 13 for the motor starting frequency.
See chapter 2.6 for setting the pressure switch.

The working pressure of a compressor fluctuates according to the limits set on the pressure switch.
The filter regulator unit reduces this fluctuation to the required pressure and holds it constant.
Precondition The machine is isolated from the air consumers.

34 Premium D No.: 9_5851 21 E
7 Initial Start-up
Fig. 10 Setting the filter regulator

1 Adjusting knob 4 Pressure gauge (working pressure)
2 Adjusting screw 5 Compressed air outlet
3 Locknut
Filter regulator A Filter regulator B

1. Start the machine and run it up to cut-out 1. Start the machine and run it up to cut-out
pressure. pressure.
2. Lift up the adjusting knob. 2. To relieve the filter regulator, turn the ad‐
3. Change the setting justing screw anticlockwise until no more re‐
■ Cut-out pressure is to be increased: sistance is felt.
Turn the adjusting screw clockwise (di‐ 3. Turn the adjusting screw clockwise until the
rection: +). pressure gauge reads the required working
■ Cut-out pressure is to be decreased: pressure.
Turn the adjusting screw anticlockwise 4. Tighten the locknut to fix the adjusting
(direction: −). screw in position.
4. Push the knob down again when the re‐
quired pressure is set.

No.: 9_5851 21 E Premium D 35
8 Operation
8.1 Switching on and off
8 Operation
8.1 Switching on and off
Always switch the machine on and off with the ON/OFF switch. The «ON/OFF» switch is located
on the pressure switch.
Precondition A power supply disconnecting device has been installed by the user.
No personnel are working on the machine.
All panels are in place and secured.
The machine temperature is at least +3° C.
DANGER
Automatic restart!
Serious injury is possible. The machine restarts automatically when power is restored after a
power cut.
Fig. 11 Switching on and off

1 «ON/OFF» switch
Switching on
1. WARNING!
Compressed air!
Serious injury is possible.
➤ Never direct compressed air at persons or animals.
3. Switch on the compressor at the pressure switch.
The compressor starts as soon as the network pressure is lower than the setpoint (cut-out
pressure).
Switching off
1. Switch the machine off at the pressure switch.

2. Switch off and lock out the power supply isolating device.

36 Premium D No.: 9_5851 21 E

The alarm indications valid for your machine are dependent on the individual equipment.
1. Do not attempt fault rectification measures other than those given in this manual.
2. In all other cases,
have the fault rectified by an authorised KAESER Service Technician.
9.2 Alarms
Alarm Possible cause Remedy
Machine does not start. A fuse has blown and the ma‐ Check motor connections and
chine is shut down. fuses (circuit breakers).
Defective pressure switch con‐ Replace the pressure switch.
tact.
Motor overload protection has Allow the motor to cool down.
tripped.
Compressor motor defective: Contact KAESER Service.
Bearing damage or winding
short-circuit.
Compressor block defective. Contact KAESER Service.
Machine starts with difficulty. Venting valve on the pressure Maintain or replace the unload‐
switch not opening. ing valve.
Bearing damage. Contact KAESER Service.
Piston seized due to insufficient Contact KAESER Service.
or incorrect oil.
Fault in the power supply. Check power supply.
Oil level too high. Drain out some oil.
Machine runs hot. Ambient temperature too high. Reduce the ambient tempera‐
ture.
Wrong direction of rotation. Change over phase lines L1
and L2.
Fan cannot draw air freely. Ensure unrestricted flow of air
to the fan.
Valves* or valve plate between Contact KAESER Service.
cylinder head and cylinder are
leaking or dirty.
Outlet valve reed broken. Contact KAESER Service.
Motor overload protection trips Fault in the power supply. Check power supply.
out after a short time. Motor fault. Contact KAESER Service.
* depending on machine

No.: 9_5851 21 E Premium D 37
9.2 Alarms

Motor overload protection trips Current too high because of low Check power supply cable con‐
out after a long time. supply voltage. ductor cross-sections.
Check and tighten connection
terminals.
The machine runs continuously Air filter clogged. Maintain or replace the air filter.
but maximum pressure is not Valves* or valve plate between Contact KAESER Service.
reached. cylinder head and cylinder are
leaking or dirty.
Outlet valve reed broken. Contact KAESER Service.
Machine leaks air. Seal the leaks or replace the
components.
Leakage from an air consumer Check possible leakage points.
connected to the air system.
The air demand is greater than Use a larger machine.
the machine's air delivery ca‐
pacity.
Machine cuts in and out too of‐ Air receiver filled with conden‐ Drain condensate.
ten. sate.
The machine switches off and Check valve defective. Replace the check valve.
air escapes from the venting
valve.
The venting valve loses air The venting valve is not clos‐ Maintain or replace the unload‐
while the machine is running. ing. ing valve.
The pressure switch does not Venting valve dirty. Maintain or replace the unload‐
vent after switching off. ing valve.
Air leaks from the pressure Defective switch diaphragm. Replace the pressure switch.
switch while the machine is run‐ The venting valve is not clos‐ Maintain or replace the unload‐
ning. ing. ing valve.
Whistling sound from the cylin‐ Cylinder head fixing screws Tighten the cylinder head fixing
der head. loose. screws.
Gasket defective. Replace gasket.
The pressure relief valve blows Pressure switch incorrectly set. Check pressure switch setting.
off before the cut-out pressure Valve spring defective. Replace safety relief valve.
is reached.
Dirt or foreign bodies on the Let the pressure relief valve
valve seat. blow off briefly.
Pressure relief valve on the air Cooler clogged. Cooler pipe Cooler maintenance.
cooler blows off prematurely. blocked with scale.
Machine uses too much oil. Viscosity too low. Fill with oil specified in the serv‐
ice manual.
Crankcase vent defective. Maintain or replace crancase
vent.
Piston rings worn or broken. Contact KAESER Service.

38 Premium D No.: 9_5851 21 E
9.2 Alarms

Piston rings worn or damaged Dirty oil. Fit finer air inlet filter.
after a short operational period.
Tab. 28 Alarms and remedies

No.: 9_5851 21 E Premium D 39
10 Maintenance
10.1 Ensuring safety
10 Maintenance
10.1 Ensuring safety

➤ Allow maintenance work to be performed by authorised personnel only.
voltage is present.
pressure.
voltage is present.


40 Premium D No.: 9_5851 21 E
10 Maintenance
10.2 Maintenance Schedule
10.2 Maintenance Schedule

10.2.1 Logging maintenance work
The maintenance intervals given are those recommended for average operating conditions.
➤ Adjust the maintenance intervals with regard to local installation and operating condi‐
tions.
➤ Keep a log of all maintenance and service work.
This enables the frequency of individual maintenance tasks and deviations from our recom‐
mendations to be determined.
Further information A prepared list is provided in chapter 10.18.
10.2.2 Regular maintenance tasks

➤ When operating conditions are unfavourable (e.g. dusty atmosphere) or when the equipment is
in constant use, maintenance tasks must be carried out more frequently (shorter intervals).
Interval Maintenance task See chapter

Daily or every 24 operat‐ Check the oil level. 10.8
ing hours Drain off condensate from the receiver. 10.12
Drain condensate from the filter regulator. 10.16
Annually Carry out air filter maintenance 10.4 / 10.5 / 10.6
Maintain the check valve. 10.14
Check that all electrical connections are tight. –
Check the pressure relief valve. 10.11
Variable, Change the compressor oil. 10.10
see table 30
h = operating hours
Tab. 29 Regular maintenance tasks
10.2.3 Oil changing intervals

Duty cycles and ambient conditions are important criteria for the number and length of the change
intervals.
Support can be obtained from KAESER Service on determining suitable changing intervals.
➤ Check operating conditions and adjust intervals as necessary; log the results in table 30 for fu‐
ture reference.
Maximum permissible oil change interval

[operating hours/year]
Compressor oil Favourable operating conditions* My operating conditions
SAE 5 W30 1000/2
VDL 150 1000/1

No.: 9_5851 21 E Premium D 41
10 Maintenance
10.3 Maintaining the air cooler or fan guard
Maximum permissible oil change interval

[operating hours/year]
Compressor oil Favourable operating conditions* My operating conditions
FGP 1000/2
Tab. 30 Oil changing intervals
10.2.4 Regular service tasks

➤ Only an authorized KAESER Service Technician should carry out service work.
➤ When operating conditions are unfavourable (e.g. dusty or humid atmosphere) or when the
equipment is in constant use, have the service work carried out more frequently (shorter inter‐
vals).
Interval Service task

Every 2 years at least Change the air filter element
Up to 3000 h Have cylinder head and valves checked.
Up to 12,000 h Have the machine generally overhauled.
Up to 12,000 h, at the lat‐ Check motor bearings
est every 3 years
h = operating hours
Tab. 31 Regular service tasks
10.3 Maintaining the air cooler or fan guard

According to machine model, it either has an air cooler of a fan guard.
Clogging causes overheating and machine damage.
Regular cleaning ensures reliable cooling of the machine and the compressed air. The frequency is
mainly dependent on local operating conditions.
Material Brush
Vacuum cleaner
Face mask (as required)
Precondition The supply disconnecting device is switched off,

a check has been made that no voltage is present.
The machine has cooled down.

42 Premium D No.: 9_5851 21 E
10 Maintenance
10.4 Air filter maintenance
Fig. 12 Cleaning the air cooler or fan guard

1 Compressed air cooler
2 Fan with guard
3 Brush
10.3.1 Cleaning the air cooler or fan guard

Do not use sharp objects to clean the air cooler or fan guard. It could cause damage.
Avoid creating clouds of dust.
➤ Dry brush the air cooler or fan guard and safety screen using a vacuum cleaner to suck up the
dirt.
The air cooler or fan guard can't be cleaned thoroughly?
➤ Have stubborn clogging removed by an authorized KAESER Service Technician.
10.4 Air filter maintenance

The type of filter element installed in the air filter depends on the model of compressor.
Possible filter elements:

■ Filter element 3a , washable but not removable.
■ Foam insert 3b , washable and removable.
If the filter element 3a is heavily clogged, clean with a solvent-based fluid or steam blaster.
Observe safety regulations.
Replace the air filter A or filter insert 3b if it has already been cleaned a number of times.
Material Compressed air for blowing out

Solvent cleaner
Cleaning cloths
Spares as required
Precondition The supply disconnecting device is switched off.

The disconnecting device is locked off.
A check has been made that no voltage is present.

No.: 9_5851 21 E Premium D 43
10 Maintenance
10.5 Air filter (sound damping) maintenance
Fig. 13 Air filter maintenance

1 Air filter 4 Retaining clip
2 Inlet air opening 5 Cover
3a Filter element 6 Air filter housing
3b Foam filter insert
Air filter A Air filter B

1. Unscrew the air filter from the cylinder head. 1. Remove the rubber cap.
2. Release the retaining clip and take off the 2. Withdraw the filter insert 3b .
cover. 3. Clean the filter insert with a solvent-based
3. Blow out the cover and filter element 3a cleaner.
with dry compressed air (< 5 bar). 4. Clean the housing and sealing faces.
4. Clean the housing and sealing faces. 5. Insert the dried filter insert in the rubber cap
5. Wet the filter element lightly with oil after and replace the cap on the filter housing.
cleaning. 6. Mount the air filter on the cylinder head
6. Position the cover over the element and such that the inlet opening is facing down‐
close the retaining clips. wards.
7. Mount the air filter on the cylinder head 7. Switch on the power supply isolating device.
such that the inlet opening is facing down‐
wards.
10.5 Option H9
Air filter (sound damping) maintenance
Check that all sealing surfaces match each other. The use of an unsuitable air filter element can
permit dirt to ingress the pressure system and cause damage to the machine.

Spares as required


44 Premium D No.: 9_5851 21 E
10 Maintenance
10.6 Air filter (plastic housing) maintenance
Fig. 14 Air filter (sound damping) maintenance

1 Air filter cartridge 3 Retaining clip
2 Inlet air opening 4 Cover
Cleaning the filter element with compressed air
1. Release the retaining clip and take off the cover.

2. Withdraw the filter element.
3. Use dry compressed air at not more than 5 bar to blow dirt from the air filter element from in‐
side to outside.
4. Inspect the air filter element for any damage.
Change the air filter element if damaged.
5. Clean the housing and sealing faces.

6. Replace the filter element.
7. Position the cover and close the retaining clips.
10.6 Option H10

Air filter (plastic housing) maintenance
Check that all sealing surfaces match each other. The use of an unsuitable air filter element can
permit dirt to ingress the pressure system and cause damage to the machine.

Spares as required


No.: 9_5851 21 E Premium D 45
10 Maintenance
10.7 Drive motor maintenance
Fig. 15 Air filter (plastic housing) maintenance

1 Cover
2 Air filter cartridge
3 Air filter housing
Cleaning the filter element with compressed air
1. Unscrew and remove the cover.

2. Withdraw the filter element.
3. Use dry compressed air at not more than 5 bar to blow dirt from the air filter element from in‐
side to outside.
4. Inspect the air filter element for any damage.
Change the air filter element if damaged.
5. Clean the housing and sealing faces.

6. Replace the filter element.
7. Replace the cover and screw down tight.
10.7 Drive motor maintenance

The drive motor bearings are permanently greased. Re-greasing is not necessary.
➤ Have the motor bearings checked by KAESER Service.
10.8 Checking the oil level

The oil level can be read off on the oil sight glass.
Precondition The machine is switched off.

46 Premium D No.: 9_5851 21 E
10 Maintenance
10.9 Topping up the compressor oil
Fig. 16 Checking the oil level

1 Oil sight glass
2 Oil filler and crankcase vent
➤ Read off the oil level daily and before each start-up.
Result Top up when the compressor oil level falls to the minimum mark. Top up the oil
10.9 Topping up the compressor oil

Material Compressor oil

CAUTION
The machine can be damaged by unsuitable oil.
➤ Never mix different types of oil.
➤ Never top up with a different type of oil to that already used in the machine.
The type of compressor oil used is listed in table 14.
Fig. 17 Topping up the compressor oil

1 Crankcase vent
1. Remove the crankcase vent from the oil filler.

2. Top up to bring the oil to the correct level.
3. Replace the crankcase vent.

No.: 9_5851 21 E Premium D 47
10 Maintenance
10.10 Changing the compressor oil
4. Start the machine and check the oil level again after about 2 minutes, topping up again, if nec‐
essary.
5. Switch off the machine and check visually for leaks.
10.10 Changing the compressor oil

Change the initial charge of oil as specified in table 29 .
Always drain the oil completely from the compressor block.
Change the oil immediately if it becomes milky.
This indicates a high condensate content.
Contact KAESER Service if condensate is detected in the oil.
Material Compressor oil

Oil receptacle

The supply disconnecting device is switched off,
CAUTION
Danger of burning from hot components and scalding from escaping oil.
➤ Wear long-sleeved clothing and gloves.
Fig. 18 Changing the compressor oil

1 Oil filler port
2 Oil sight glass
3 Oil drain plug
Draining the oil
1. Remove the crankcase vent from the oil filler.

2. Position the oil receptacle.
3. Remove the drain plug and allow oil to drain into the receptacle.
4. Replace the drain plug after making sure the gasket is not damaged.
Dispose of the old oil in accordance with valid environmental protection regulations.

48 Premium D No.: 9_5851 21 E
10 Maintenance
10.11 Checking the pressure relief valve
Filling with oil
1. Fill with new oil to the maximum mark on the oil sight glass.
2. Replace the crankcase vent.
3. Start the machine and check the oil level again after about 2 minutes, topping up again, if nec‐
essary.
4. Switch off the machine and check visually for leaks.
10.11 Checking the pressure relief valve

➤ To test the pressure relief valve, it must be removed from the machine by a KAESER Service
Technician and installed on a test rig.
Further information Details about the activating pressure of the pressure relief valve are found in chapter 2.7.
10.11.1 Pressure relief valve in the collecting pipe

To prevent the pressure relief valve's seat from sticking, ensure that the valve is regularly activated
- once a year at the very least.
The valve opens to protect the machine if the maximum permissible working pressure is ex‐
ceeded.
➤ Never operate the machine without a correctly functioning pressure relief valve.
➤ Do not adjust the pressure relief valve.
Precondition Machine runs in LOAD
Fig. 19 Checking the collecting pipe relief valve

1 Pressure relief valve in the collecting pipe
2 Knurled knob
1. WARNING!
Risk of hearing damage when pressure relief valve blows off!
Risk of burning from compressed air when pressure relief valve blows off!
➤ Wear ear and eye protection.
2. Turn the knurled knob on the pressure relief valve anticlockwise until the compressed air blows
off.
3. Then turn the knurled knob back to its original position.
Pressure relief valve does not blow off?
➤ Have the defective pressure relief valve immediately replaced by KAESER Service.

No.: 9_5851 21 E Premium D 49
10 Maintenance
10.12 Air receiver maintenance
10.11.2 Air receiver pressure relief valve

To prevent the pressure relief valve's seat from sticking, ensure that the valve is regularly activated
- once a year at the very least.
The valve opens to protect the machine if the maximum permissible working pressure is ex‐
ceeded.
➤ Never operate the machine without a correctly functioning pressure relief valve.
➤ Do not adjust the pressure relief valve.
Precondition Machine under LOAD deactivated (air receiver under maximum pressure).
Disconnect device secured against being switched on.
Absence of voltage is verified.
User's shut-off valve between the machine and the air network is closed.
Fig. 20 Checking pressure relief valve on the air receiver

1 Pressure relief valve
2 Knurled knob
1. WARNING!
Risk of hearing damage when pressure relief valve blows off!
Risk of burning from compressed air when pressure relief valve blows off!
➤ Wear ear and eye protection.
2. Turn the knurled knob on the pressure relief valve anticlockwise until air blows off.
3. Then turn the knurled knob back to its original position.
4. Open the user's shut-off valve between the machine and the air distribution network.
Result The machine can now be started.
Pressure relief valve does not blow off?

➤ Have the defective pressure relief valve immediately replaced by KAESER Service.
10.12 Air receiver maintenance

Material Collection chamber
Checking the air receiver
Pressure vessels must be inspected at regular intervals in accordance with legal requirements.
➤ Observe relevant national regulations.
Draining condensate
Some of the moisture contained in the compressed air precipitates out in the air receiver.

50 Premium D No.: 9_5851 21 E
10 Maintenance
10.13 Venting the machine (de-pressurising)
Fig. 21 Draining condensate

1 Condensate drain tap
➤ Drain the condensate out daily.

Drain the condensate into a suitable receptacle and dispose of according to environmental
regulations.
10.13 Venting the machine (de-pressurising)

After being switched off, the machine is still under pressure from the air network up to the check
valve.
The machine must be isolated from the air network and completely vented before undertaking
any maintenance or service work on the pressure system.
Precondition The power supply isolating device is switched off,

Fig. 22 Venting the machine

1. DANGER!
Compressed air!
Compressed air and devices under pressure can injure or cause death if the contained energy
is released suddenly.
➤ Isolate the compressor from the air system.
2. Open the condensate outlet slowly to release pressure.
3. Verify the absence of pressure using a suitable measuring device (pressure gauge).

No.: 9_5851 21 E Premium D 51
10 Maintenance
10.14 Maintaining the check valve
The machine is not de-pressurised after having been vented?

Shut-off valve still open.
➤ Defective condensate drain.
➤ If manual venting does not attain de-pressurisation: Contact the authorised
KAESER Service.
10.14 Maintaining the check valve

The check valve is installed in the air receiver inlet port. It prevents the compressed air from flow‐
ing back from the air receiver to the compressor block.

Cleaning cloths
Spares as required

The machine is fully vented (no pressure).
Fig. 23 Cleaning the check valve

1 Enclosure 4 Valve seat
2 Screw plug 5 Spring
3 Valve cone 6 O-ring
1. CAUTION!
Danger of burns from hot components!
➤ Wear long-sleeved clothing and gloves.
➤ Work with caution.
2. Remove the plug.
3. Clean the valve cone and seat.
The complete valve must be replaced if the valve seat is badly worn or damaged.
4. Insert the valve cone, spring and O-ring in the valve seat.
5. Close the check valve with screw plug and O-ring.

52 Premium D No.: 9_5851 21 E
10 Maintenance
10.15 Maintenance of the pressure switch unloading valve
10.15 Maintenance of the pressure switch unloading valve

The unloading valve must be cleaned in the following circumstances:
■ Machine starts with difficulty.
■ The machine does not vent after switching off.

Cleaning cloths
Spares as required

Fig. 24 Maintenance of the pressure switch unloading valve

1 Unloading valve 5 Spring
2 Screw 6 Gasket
3 Screw plug 7 Pin
4 Ball 8 Screw fixings
Open the valve carefully.
1. Remove the fitting from the valve.

2. Loosen the securing screws and take off the unloading valve.
3. Remove the screw plug and take out the individual parts.
4. Extract the pin and clean it and the other parts, blowing out if necessary.
5. After reassembly insert the unloading valve and tighten down with the screw.
10.16 Filter regulator maintenance

Empty accumulating condensate at regular intervals, at least once a day.

No.: 9_5851 21 E Premium D 53
10 Maintenance
10.17 Cylinder head and valves

Cleaning cloths
Spares as required

➤ Drain condensate.
➤ Collect the condensate in a suitable container and dispose of in accordance with environ‐
mental regulations.
Cleaning the filter element
Fig. 25 Cleaning the filter regulator

2 Enclosure
3 Filter element
1. Unscrew the enclosure, remove and clean the filter element, if necessary blow out with com‐
pressed air (<5 bar!).
Note the instructions on the enclosure of the filter pressure regulator.
2. Blow out the casing with compressed air (< 5 bar).

3. Reassemble the parts and make sure they sit correctly.
10.17 Cylinder head and valves

The condition of the valves can be assessed by measuring the air receiver charging time and com‐
paring this with the charging time when the machine was new.
➤ Start the machine and measure the receiver charging time.
Result If there is a significant difference in the charging time to when the machine was new, have
KAESER Service check or replace the valves.
Further information See chapter 7.7 for air receiver charging time measurement.

54 Premium D No.: 9_5851 21 E
10 Maintenance
10.18 Documenting maintenance and service work
10.18 Documenting maintenance and service work

Machine number:
➤ Enter maintenance and service work carried out in the list.
Date Maintenance task carried out Operating hours Signature
Tab. 32 Logged maintenance tasks

No.: 9_5851 21 E Premium D 55
11.1 Note the nameplate

11.1 Note the nameplate
The nameplate contains all information to identify your machine. This information is essential to us
in order to provide you with optimal service.
➤ Please give the information from the nameplate with every enquiry and order for spares.
11.2 Ordering consumable parts and operating fluids/materials

KAESER consumable parts and operating materials are original Kaeser products. They are selec‐
ted for use in KAESER machines.
WARNING
There is risk of personal injury or damage to the machine resulting from the use of unsuita‐
ble spares or operating fluids/materials.
Unsuitable or poor quality consumable parts and operating fluids/materials may damage the
machine or impair its proper function.
Personal injury may result from machine damage.
➤ Use only original KAESER parts and operating fluids/materials.
➤ Have an authorised KAESER Service Technician carry out regular maintenance.
Fig. 26 Consumable parts

10 Air filter 40 Air filter element (plastic housing)
20 Air filter element 50 Check valve G 3/8
30 Air filter element (silenced) 60 Check valve G 1/2
Machine
Name Option Quantity Number

Air filter 1/2* 10
Air filter element 1 20
Air filter element (silenced) H9 1/2* 30
Air filter element (plastic housing) H10 1/2* 40
Check valve G 3/8 1 50
Check valve G 1/2 1 60
Compressor oil SAE 5 W30 0.5l 9.4943.00010
Compressor oil VDL 150 1.0l 9.0894.1
Compressor oil FGP 1.0l 9.0874.0
Tab. 33 Consumable parts

56 Premium D No.: 9_5851 21 E
11.3 Service Addresses
11.3 Service Addresses

Addresses of KAESER agents are given at the end of this manual.
11.4 KAESER AIR SERVICE

KAESER AIR SERVICE offers:
■ Authorised service technicians with KAESER factory training
■ Increased operational reliability ensured by preventive maintenance
■ Energy savings achieved by avoidance of pressure losses
■ optimum conditions for operation of the compressed air system,
■ The security of genuine KAESER spares.
■ Increased legal certainty as all regulations are kept to.
➤ It make sense to sign a KAESER AIR SERVICE maintenance agreement.

Your advantage:
lower costs and higher compressed air availability.
11.5 Spares for service and repair

➤ Make sure that any service or repair tasks not described in this manual are carried out by
an authorised KAESER Service Technician.

No.: 9_5851 21 E Premium D 57
12.1 Decommissioning

12.1 Decommissioning
De-commissioning is necessary, for example, under the following circumstances:
■ The machine is temporarily not needed.
■ The machine is to be moved to another location.
■ The machine is to be scrapped.
Temporary de-commissioning
Precondition The machine can be started at regular intervals.
➤ Run the machine once a week under load for at least 30 minutes to ensure sufficient corrosion
protection.
Long-term de-commissioning
Precondition The machine must have run for at least 30 minutes before before long-term de-commissioning.
The machine is isolated from the mains,
the device is secured to prevent switching back on,
The machine is fully vented (depressurized).
1. Allow the machine to completely cool down.

2. Spray the valves and cylinder bore with Shell Ensis 20 preserving oil.
The oil does not need to be removed when re-commissioning.
3. Drain all condensate.

4. Disconnect all air and electrical connections.
5. Spray all contacts and terminals with a preservative (e.g. Rivalto, W.S.X.).
12.2 Packing
A wooden crate is required for overland transport to protect the machine from mechanical damage.
Other measures must be taken for the transport of machines by sea or air. Please contact
KAESER Service for more information.
Material Desiccant
Plastic sheeting
Wooden crate
Precondition The machine is decommissioned.

Machine is dry and cooled down.
1. Wrap the machine fully in plastic sheeting.

2. Place sufficient desiccant (e.g. silica gel) inside the plastic sheeting.
3. Protect the machine in a wooden crate against mechanical damages.

58 Premium D No.: 9_5851 21 E
12.3 Storage
12.3 Storage
Moisture can lead to corrosion, particularly on the surfaces of the compressor block.
Frozen moisture can damage components, valve diaphragms and gaskets.
Please consult with KAESER if you have questions to the appropriate storage and commis‐
sioning.
1. NOTICE!
Moisture and frost can damage the machine!
➤ Prevent ingress of moisture and formation of condensation.
➤ Maintain a storage temperature of >0 °C.
2. Store the machine in a dry, frost-proof room.
12.4 Transporting
12.4.1 Safety
Avoid damaging the machine.
➤ Transport only with the enclosure fully closed.
12.5 Disposal
When disposing of a machine, drain out all liquids and remove dirty filters.
Precondition The machine is decommissioned.
1. Completely drain the oil from the machine.

2. Remove old filters.
3. Hand the machine over to an authorized disposal expert.
➤ Components contaminated with oil must be disposed of in accordance with local environ‐
ment protection regulations.

No.: 9_5851 21 E Premium D 59
13 Annex
13.1 Dimensional Drawing
13 Annex

60 Premium D No.: 9_5851 21 E
13 Annex

No.: 9_5851 21 E Premium D 61
13 Annex
13.2 Electrical Diagram

62 Premium D No.: 9_5851 21 E
13 Annex

No.: 9_5851 21 E Premium D 63
13 Annex

64 Premium D No.: 9_5851 21 E

Service Manual: Reciprocating Compressor Premium D

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: Reciprocating Compressor Premium D

Uploaded by

Copyright:

Available Formats

Service Manual

1 Regarding this document

Service Manual Reciprocating compressor

4.2.3 Hose reel ............................................................................................................ 24

Service Manual Reciprocating compressor

10.13 Venting the machine (de-pressurising) ............................................................................ 51

Service Manual Reciprocating compressor

Service Manual Reciprocating compressor

Fig. 1 Location of safety signs .............................................................................................................. 20

Service Manual Reciprocating compressor

Service Manual Reciprocating compressor

Tab. 1 Danger levels and their definition (personal injury) .................................................................... 1

Service Manual Reciprocating compressor

Service Manual Reciprocating compressor

1 Regarding this document

1.2 Further documents

Missing documents can be requested from KAESER.

1.4 Symbols and labels

Tab. 1 Danger levels and their definition (personal injury)

Service Manual Reciprocating compressor

1.4.2 Potential damage warnings

Warning notices for damages are identified by their signal term.

Tab. 2 Danger levels and their definition (damage to property)

➤ Carefully read and fully comply with warnings against damages.

1.4.3 Other alerts and their symbols

Service Manual Reciprocating compressor

Further information Further subjects are introduced here.

Service Manual Reciprocating compressor

Option Option code Available?

Compressor model Air receiver size [l] Mass [kg]

Service Manual Reciprocating compressor

Compressor model Air receiver size [l] Mass [kg]

2.4 Compressor block

Tab. 6 Compressor block

2.5 Ambient conditions

Tab. 7 Ambient conditions

2.6 Pressure switch setting

Service Manual Reciprocating compressor

Tab. 8 Pressure switch setting

Tab. 9 Air receiver pressure relief valve setting

Pressure relief valve in the collecting pipe*

Tab. 10 Collecting pipe relief valve setting

2.8 Sound emission

Emission sound pressure level

Service Manual Reciprocating compressor

Tab. 11 Sound pressure level

2.9 Motor power and speed

Compressor model Compressor Rated pow‐ Synchronous Enclosure pro‐

Tab. 12 Power and speed

Permissible starting frequency

Rated power [kW] Permissible starting frequency [1/h]

Tab. 13 Permissible starting frequency

Service Manual Reciprocating compressor

2.10 Compressor oil recommendations

Standard oil Special oil

Tab. 14 Compressor oil recommendations

2.10.1 Compressor oil charge

Tab. 15 Compressor oil charge

Service Manual Reciprocating compressor

2.11 Electrical connection

2.11.1 Three-phase power supply

2.11.1.1 Power supply specifications

Other conditions would include, for example: