DF-61010:C

SD365 Series
Addressable Photoelectric Smoke Detectors

Addressable Devices
The Fire•Lite® Alarms SD365(A), SD365R(A), and SD365HT(A)
intelligent plug-in smoke detectors are designed for both perfor-
mance and aesthetics, and are direct replacements for the SD355
Series. A new modern, sleek, contemporary design and enhanced
optical sensing chamber is engineered to sense smoke produced by
a wide range of combustion sources in accordance with more strin-
gent code standards.
Exclusively for use with Fire•Lite’s addressable fire alarm control
panels, the SD365(A) Series point ID capability allows each detec-
tor’s address to be set with rotary, decimal address switches, provid-
ing exact detector location for emergency personnel to quickly locate
a fire during its early stages, potentially saving precious rescue time
while also reducing property damage. Two LEDs on each sensor
light to provide a local, visible sensor indication.
The SD365(A) Series also offers 135°F (57°C) fixed temperature
thermal sensing on the SD365T(A) and a remote test capable detec-
tor on the SD365R(A) for use with DNR(A)/DNRW duct smoke
detector housings.

Features • Plugs into separate base for ease of installation and maintenance
SLC LOOP: • Separate base allows interchange of photoelectric, ionization and
thermal sensors
• Two-wire SLC loop connection
• Unit uses base for wiring OPTIONS:
• Compatible with LiteSpeed™ and CLIP protocol systems • Optional relay, isolator, and sounder bases
• Stable communication technique with noise immunity
Installation
ADDRESSING: SD365 Series plug-in intelligent smoke detectors use a detachable
• Addressable by device base to simplify installation, service and maintenance. Installation
• Rotary, decimal addressing instructions are shipped with each detector.
(Refer to the Fire•Lite panel manuals for device capacity.) Mount detector base (all base types) on an electrical backbox which
ARCHITECTURE: is at least 1.5" (3.81 cm) deep. For a chart of compatible junction
boxes, see DF-60059.
• Sleek, low-profile, stylish design
NOTE: Because of the inherent supervision provided by the SLC loop,
• Unique single-source design to respond quickly and dependably end-of-line resistors are not required. Wiring “T-taps” or branches are
to a broad range of fires permitted for Class “B” wiring only.
• Integral communications and built-in device-type identification When using relay or sounder bases, consult the I300(A) installation
• Built-in tamper resistant feature sheet I56-3626 for device limitations between isolator modules and isola-
tor bases.
• Remote test feature from the panel
• Walk test with address display (an address on 121 will blink the Construction
detector LED: 12-[pause]-1(LiteSpeed systems only)
These detectors are constructed of fire-resistant plastic. The SD365
• Built-in functional test switch activated by external magnet Series plug-in intelligent smoke detectors are designed to commer-
• Removable cover and insect-resistant screen for simple field cial standards and offer an attractive appearance.
cleaning
• Expanded color options Operation
Each SD365 Series detector uses one of the panel’s addresses
OPERATION:
(total limit is panel dependent) on the Fire•Lite Signaling Line Circuit
• Designed to meet UL 268 7th Edition (SLC). It responds to regular polls from the control panel and reports
• Factory preset at 1.5% nominal sensitivity for panel alarm thresh- its type and the status. If it receives a test command from the panel
old level (or a local magnet test), it stimulates its electronics and reports an
• LED “blinks” when the unit is polled (communicating with the fire alarm. It blinks its LEDs when polled and turns the LEDs on when
panel) and latches in alarm. commanded by the panel. The SD365 Series offers features and
performance that represent the latest in smoke detector technology.
• Low standby current
MECHANICALS: Detector Sensitivity Test
• Sealed against back pressure Each detector can have its sensitivity tested (required per NFPA 72,
• SEMS screws for wiring of the separate base Chapter 14 on Inspection, Testing and Maintenance) when installed/
connected to an Fire•Lite addressable fire alarm control panel. The
• Designed for direct-surface or electrical-box mounting
results of the sensitivity test can be printed for record keeping.

DF-61010:C • 5/28/2020 — Page 1 of 3

Product Line Information B200SA-WH: Same as B200S-WH, ULC listing
NOTE: “-IV” suffix indicates CLIP and LiteSpeed device. B200SA-IV: Same as B200S-IV, ULC listing
NOTE: “A” suffix indicates Canadian version. B200SCOA-WH: White, Intelligent, programmable sounder base in
English/French (required in Canada for ULC applications with CO
SD365: White, low-profile intelligent photoelectric sensor, LiteSpeed
Series detector applications
only
B200SCOA-IV: Ivory Intelligent, programmable sounder base in
SD365A: Same as SD365 but with ULC listing English/French (required in Canada for ULC applications with CO
SD365-IV: Ivory, low-profile intelligent photoelectric sensor Series detector applications, ULC listing
SD365A-IV: Same as SD365-IV but with ULC listing B200S-LF-WH: White, Low Frequency Intelligent, programmable
sounder base. Produces a fundamental frequency of 520 Hz +/-
SD365T: White, same as SD365 but includes a built-in 135°F (57°C) 10% with a square wave or its equivalent; designed to meet the
fixed-temperature thermal device, LiteSpeed only NFPA 72 sleeping space requirement. (CSFM: 7300-1653:0238)
SD365TA: Same as SD365T but with ULC listing B200S-LF-IV: Ivory, Low Frequency Intelligent, programmable
SD365T-IV: Ivory, same as SD365T but includes a built-in 135°F sounder base. Produces a fundamental frequency of 520 Hz +/-
(57°C) fixed-temperature thermal device 10% with a square wave or its equivalent; designed to meet the
NFPA 72 sleeping space requirement. (CSFM: 7300-1653:0238)
SD365TA-IV: Same as SD365T-IV but with ULC listing
B200SR-WH: White, Intelligent sounder base capable of producing
SD365R: White, low-profile intelligent photoelectric sensor, remote sound output with ANSI Temporal 3 or continuous tone. Intended for
test capable, for use with DNR/DNRW, LiteSpeed only retrofit applications. (CSFM: 7300-1653:0213)
SD365RA: Same as SD365R but with ULC listing, for use with B200SR-IV: Ivory, Intelligent sounder base capable of producing
DNRA sound output with ANSI Temporal 3 or continuous tone. Intended for
retrofit applications. (CSFM: 7300-1653:0213)
SD365R-IV: Ivory, low-profile intelligent photoelectric sensor, remote
test capable, for use with DNR/DNRW B200SRA-WH: Same as B200SR-WH with, ULC listing
SD365RA-IV: Same as SD365R-IV but with ULC listing, for use with B200SRA-IV: Same as B200SR-IV in Ivory color, ULC listing
DNRA B200SR-LF-WH: White, Low Frequency Intelligent, programmable
sounder base. Produces a fundamental frequency of 520 Hz +/-
INTELLIGENT BASES
10% with a square wave or its equivalent; designed to meet the
NOTE: For details on intelligent bases, see DF-60059. NFPA 72 sleeping space requirement. Intended for retrofit applica-
B300-6: White, 6” base, standard flanged low-profile mounting base tions. (CSFM: 7300-1653:0238)
(CSFM: 7300-1653:0109) B200SR-LF-IV: Ivory, Low Frequency Intelligent, programmable
B300-6-IV: Ivory,6” base, standard flanged low-profile mounting sounder base. Produces a fundamental frequency of 520 Hz +/-
base (CSFM: 7300-1653:0109) 10% with a square wave or its equivalent; designed to meet the
NFPA 72 sleeping space requirement. Intended for retrofit applica-
B300A-6: Same as B300-6, ULC listed tions. (CSFM: 7300-1653:0238)
B300A-6-IV: Ivory, 6” standard flanged low-profile mounting base,
ULC listed MOUNTING KITS AND ACCESSORIES
TR300: White, replacement flange for B210LP(A) base
B300-6-BP: Bulk pack of B300-6, package contains 10
TR300-IV: Ivory, replacement flange for B210LP(A) base
B501-WHITE: White, 4” standard European flangeless mounting
base. UL/ULC listed (CSFM: 7300-1653:0109) RA100Z(A): Remote LED annunciator. 3-32 VDC. Mounts to a U.S.
single-gang electrical box. For use with B501(A) and B300-6(A).
B501-BL: Black, 4” standard European flangeless mounting base.
UL/ULC listed (CSFM: 7300-1653:0109) M02-04-00: Test magnet
B501-IV: Ivory color, 4” standard European flangeless mounting M02-09-00: Test magnet with telescoping handle
base. UL/ULC listed (CSFM: 7300-1653:0109) CK300: Color Kit (includes cover and trim ring), white, 10-pack
B501-WHITE-BP: Bulk pack of B501-WHITE contains 10 CK300-IV: Color Kit (includes cover and trim ring), ivory, 10-pack
B224RB-WH: White, relay base (CSFM: 7300-1653:0216) CK300-BL: Color Kit (includes cover and trim ring), black, 10-pack
B224RB-IV: Ivory, relay base (CSFM: 7300-1653:0216)
B224RBA-WH: White, relay base, ULC listing
B224RBA-IV: Ivory, relay base, ULC listing
B224BI-WH: White, isolator detector base (CSFM: 7300-1653:0216)
B224BI-IV: Ivory isolator detector base (CSFM: 7300-1653:0216)
B224BIA-WH: White, isolator detector base, ULC listing
B224BIA-IV: Ivory isolator detector base, ULC listing
B200S-WH: White, Intelligent addressable sounder base capable of
producing sound output in high or low volume with ANSI Temporal 3,
ANSI Temporal 4, continuous tone, marching tone, and custom tone.
Uses LiteSpeed protocol. (CSFM: 7300-1653:0213)
B200S-IV: Ivory, Intelligent addressable sounder base capable of
producing sound output in high or low volume with ANSI Temporal 3,
ANSI Temporal 4, continuous tone, marching tone, and custom tone.
Uses LiteSpeed protocol. (CSFM: 7300-1653:0213)

Page 2 of 3 — DF-61010:C • 5/28/2020

SYSTEM SPECIFICATIONS
Sensitivity: Listings and Approvals
• UL Applications: 0.5% to 4.0% per foot obscuration. Listings and approvals below apply to the SD365 Series detectors.
• ULC Applications: 0.5% to 3.5% per foot obscuration In some cases, certain modules may not be listed by certain
Size: 2.0" (51mm) high; base determines diameter approval agencies, or listing may be in process. Consult factory for
latest listing status.
– B300-6: 6.1" (15.6 cm) diameter
• UL/ULC Listing: S1059
– B501: 4" (10.2 cm) diameter
• FM Approved
For a complete list of detector bases see DF-60983
• CSFM: 7272-0075:0502
Shipping weight: 3.4 oz. (95 g)
Operating temperature range:
• SD365: 32°F to 122°F (0°C to 50°C)
• SD365T Series: 32°F to 100°F(0°C to 38°C)
• SD365R Series installed in a DNR/DNRW, -4°F to 158°F (-20°C
to 70°C)
UL/ULC Listed Velocity Range: 0-4000 ft/min. (1219.2 m/min.),
suitable for installation in ducts
Relative humidity: 10% – 93% non-condensing
Thermal ratings: fixed-temperature set point 135°F (57°C), rate-of-
rise detection 15°F (8.3°C) per minute, high temperature heat 190°F
(88°C)
ELECTRICAL SPECIFICATIONS
Voltage range: 15 - 32 volts DC peak
Standby current (max. avg.): 200µA @ 24 VDC (o ne communica-
tion every 5 seconds with LED enabled)
Max current: 4.5 mA @ 24 VDC (“ON”)
DETECTOR SPACING AND APPLICATIONS
Fire•Lite recommends spacing detectors in compliance with NFPA
72. In low airflow applications with smooth ceiling, space detectors
30 feet (9.1m). For specific information regarding detector spacing,
placement, and special applications refer to NFPA 72. A System
Smoke Detector Application Guide, document SPAG91, is available
at www.systemsensor.com.

LiteSpeed™ is a trademark, and Fire•Lite® Alarms and System Sensor® are

registered trademarks of Honeywell International Inc.
©2020 by Honeywell International Inc. All rights reserved. Unauthorized use of this
document is strictly prohibited.

This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.

For more information, contact Fire•Lite Alarms. Phone: (800) 627-3473, FAX:(877) 699-4105. Country of Origin: Mexico
www.firelite.com

Page 3 of 3 — DF-61010:C • 5/28/2020