Intelligent Plug-In Photoelectric Smoke Detectors with FlashScan Intelligent/Addressable Devices
General
6934pho1.jpg Notifier 851 Series intelligent plug-in smoke detectors with integral communication provide features that surpass conven- tional detectors. Detector sensitivity can be programmed in the control panel software. Sensitivity is continuously moni- tored and reported to the panel. Point ID capability allows each detectors address to be set with decade address switches, providing exact detector location for selective main- tenance when chamber contamination reaches an unaccept- able level. The FSP-851 photoelectric detectors unique optical sensing chamber is engineered to sense smoke pro- FSP-851 with B710LP base duced by a wide range of combustion sources. Dual electronic thermistors add 135F (57C) fixed-temperature thermal sens- ing on the FSP-851T. FSP-851 and FSP-851T detectors are
6935pho1.jpg compatible with all Notifier intelligent Fire Alarm Control Pan- els (FACP). FlashScan (U.S. Patent 5,539,389) is a communication pro- tocol developed by Notifier engineering that greatly enhances the speed of communication between analog intelligent devices. Intelligent devices communicate in a grouped fash- ion. If one of the devices in the group has new information, the panels CPU stops the group poll and concentrates on single points. The net effect is response speed greater than five FSP-851T with B710LP base times that of earlier designs.
Features Sleek, low-profile design. Specification Addressable-analog communication. Size: 2.1 (5.3cm) high x 4.1 (10.4cm) diameter installed in Stable communication technique with noise immunity. B501 base, 6.1 (15.5cm) diameter installed in B710LP base. Low standby current. Shipping Weight: 5.2oz. (147g). Two-wire SLC connection. Operating Temperature: FSP-851, 0C to 49C (32F to FlashScan (NFS-640, NFS-3030) and classic CLIP sys- 120F); FSP-851T, 0C to 38C (32F to 100F). Low temper- tems (AFP-100, AFP-200, AFP-300, AFP-400, NFS-640, ature signal for FSP-851T at 45F +/- 10F (7.22C +/- AM2020/AFP1010, NFS-3030) compatible. 5.54C). Rotary, decimal addressing (1-99 on current classic sys- UL Listed Velocity Range: 0-4000 ft/min. (1219.2 m/min.), tems, 1-159 on FlashScan systems). suitable for installation in ducts. Optional remote, single-gang LED accessory (RA400Z). Relative Humidity: 10%-93% noncondensing. Dual LED design provides 360 viewing angle. Thermal Ratings: Fixed-temperature setpoint 135F (57C). Visible bi-color LEDs blink green every time the detector is addressed, and illuminate steady red on alarm. DETECTOR SPACING AND APPLICATIONS Remote test feature from the panel. Notifier recommends spacing detectors in compliance with Walk test with address display (an address on 121 will blink NFPA 72. In low airflow applications with smooth ceiling, the detector LED: 12-[pause]-1(FlashScan systems only). space detectors 30 feet (9.144m) for ceiling heights 10 feet (3.148m) and higher. For specific information regarding Built-in functional test switch activated by external magnet. detector spacing, placement, and special applications refer to Built-in tamper-resistant feature. NFPA 72. System Smoke Detector Application Guide, Sealed against back pressure. document A05-1003, is available at systemsensor.com Constructed of off-white Bayblend, designed to commer- FSP-851 and FSP-851T are listed for use in ducts, but they cial standards, and offers an attractive appearance. are NOT listed for use inside duct smoke detector housings. 94-5V plastic flammability rating. See Duct Application Smoke Detectors Guide, document A05- SEMS screws for wiring of the separate base. 1004, available at systemsensor.com, for details on pendant- mount applications. Optional relay, isolator, and sounder bases. Backward compatible.
DN-6935:A 12/28/06 Page 1 of 3
ELECTRICAL SPECIFICATIONS Voltage Range: 15-32 volts DC peak.
6833addr.wmf Standby Current (max. avg.): 250A @ 24VDC (with no communication enabled); 360A @ 24VDC (one communica- tion every five minutes with LED enabled). LED Current (max.): 6.5mA @ 24VDC (ON). BASES AVAILABLE B710LP: 6.1 (15.5cm) diameter. B501: 4.1 (10.4cm) diameter. B501BH or B501BHT: Sounder base assembly. Includes B501 base. B224RB Relay Base: Screw Terminals, up to 14AWG Address Dial on back of Detector (2.0mm2); Relay Type, Form-C; Rating, 2.0A @ 30VDC resis- tive, 0.3A @ 110VDC inductive, 1.0A @ 30VDC inductive; Dimensions, 6.2 (15.748cm) x 1.2 (3.048cm) x 1.2 (3.048cm). 4762wir1.tif
B224BI Isolator Base: Dimensions, 6.2 (15.748cm) x 1.2
(3.048cm) x 1.2 (3.048cm); Maximum, 25 devices between isolator bases.
Installation FSP-851 plug-in detectors use a separate base to simplify installation, service, and maintenance. A special tool allows maintenance personnel to plug in and remove detectors with- out using a ladder. Mount base on an electrical backbox which is at least 1.5 (3.81cm) deep. Suitable mounting base boxes include: Wiring Diagram 4.0 (10.16cm) square box. 3.5 (8.89cm) or 4.0 (10.16cm) octagonal box. Single-gang box (except relay or isolator base). With B501BH or B501BHT base, use a 4.0 (10.16cm) square box. With B224RB or B224BI base, use a 3.5 (8.89cm) octago- nal box, or a 4.0 (10.16cm) octagonal or square box. NOTE: 1) Because of inherent supervision provided by the SLC loop, end-of-line resistors are not required. Wiring T-taps or branches are permitted for style 4 (Class B) wiring. 2) When using relay or sounder bases, consult data sheet DN-2243 (ISO-X) for device limitations between isolator modules and isolator bases.
Agency Listings and Approvals
These listings and approvals apply to the modules specified in this document. In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. UL Listed: S1115 ULC Listed: CS915 (FSP-962A, FSP-851TA) MEA Listed: 225-02-E FM Approved CSFM: 7272-0028:206 Maryland State Fire Marshal: Permit # 2122 BSMI: CI313066760036 CCCF: Certif. # 2004081801000017 (FSP-851T) Certif. # 2004081801000016 (FSP-851) Lloyds Register: 03/60011
Page 2 of 3 DN-6935:A 12/28/06
Product Line Information STI 9609:High-profile, flush-mount, smoke detector guard, wire.* NOTE: A suffix indicates ULC listed model. STI 9605:High Profile, surface-mount, smoke detector guard, FSP-851:Low-profile intelligent photoelectric sensor. Must be wire.* mounted to one of the bases listed below. STI 9604:Flush-mount, heat detector guard, wire.* FSP-851A:Same as FSP-851 but with ULC listing. STI 9610:Surface-mount, heat detector guard, wire.* FSP-851T:Same as FSP-851 but includes a built-in 135F (57C) fixed-temperature thermal device. STI-8200-SS:Flush-mount stainless steel smoke detector guard (compatibility pending). FSP-851TA:Same as FSP-851T but with ULC listing. STI-8230-SS:Surface mount stainless steel smoke detector BASES guard (compatibility pending). B710LPBP:Standard U.S. low-profile base, pkg. of 10. * For dimensions and additional information on STI Steel Web B710LPA:Standard U.S. low-profile base, ULC listing. Stoppers, see data sheet DN-4936.
B501BP:Standard European flangeless base, pkg. of 10.
B501A:Standard European flangeless base, ULC listing. B501BH(A):Sounder base, includes B501(A) base. B501BHT(A):Same as B501BH(A), but includes temporal sounder. B224RB(A):Intelligent relay base. B224BI(A):Intelligent isolator base. Isolates SLC from loop shorts. ACCESSORIES F110:Retrofit replacement flange for older style bases. Con- verts old high profile base for use with FlashScan detectors. RA400Z(A):Remote LED annunciator. 3-32VDC. Fits U.S. single-gang electrical box. Supported by B710LP(A) and B501(A) bases only. SMK400:Surface mounting kit provides for entry of surface wiring conduit. For use with B501(A) base only. RMK400:Recessed mounting kit. For use with B501(A) base only. SMB600:Surface mounting kit for use with B710LP(A). BCK-200B:Black detector covers, box of 10. For use with FSP-851 only. M02-04-01:Test magnet. M02-09-00:Test magnet with telescope stick. XR2B:Detector removal tool. Allows installation and/or removal of FlashScan Series detector heads from base in high ceiling installations. T55-127-000:Detector removal tool without pole. XP-4:Extension pole for XR2B. Comes in three 5-ft. sections. DETECTOR GUARDS NOTE: Some guards listed below may not be applicable to FPS models. SDG-773:Smoke detector guard; cover is 7.0 (17.78cm) square x 3.0 (7.62cm) deep. This guard is mechanically com- patible with FSP-751. It is UL-compatibility listed with the FSP-851 (file UL S5515). STI 9601:Low-profile , flush-mount smoke detector guard, Notifier and FlashScan are registered trademarks of Honeywell Interna- wire.* tional Inc. Bayblend is a registered trademark of Bayer Corporation. 2007 by Honeywell International Inc. All rights reserved. Unauthorized use STI 9602:Low-profile, surface-mount, smoke detector guard, of this document is strictly prohibited. wire.*
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. Made in the U.S. A. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com
