Smoke Detector FSI-851 - 0

dn-6934:a
FSI-851 Series
Intelligent Plug-In Ionization
Smoke Detector with FlashScan®
Intelligent/Addressable Devices
General
FSI-851 Series intelligent plug-in ion detectors with integral
communication has features that surpass conventional detec-
tors. Detector sensitivity can be programmed in the control
panel software. Sensitivity is continuously monitored and
reported to the panel. Point ID capability allows each detector’s
address to be set with decade address switches, providing exact
detector locations for selective maintenance when chamber
contamination reaches an unacceptable level.
The FSI-851 Series ionization detector incorporates a unique
single-source, dual-chamber design to respond quickly and
dependably to a broad range of fires. FSI-851 Series detectors 6934pho1.jpg
are compatible with ONYX series and CLIP series intelligent

Fire Alarm Control Panels (FACPs).
FlashScan® (U.S. Patent 5,539,389) is a communication proto- FSI-851 Series
col developed by NOTIFIER that greatly improves the speed of
communication between analog intelligent devices and certain with B710LP base
NOTIFIER systems. Intelligent devices communicate in a
grouped fashion. If one of the devices within the group has new
information, the panel’s CPU stops the group poll and concen-
UL/ULC-Listed Velocity Range: ION: 0 – 1200 ft./min. (365.76
trates on single points. The net effect is response speed greater
m/min.).
than five times that of other protocols.
Relative Humidity: 10% – 93% noncondensing.
Features ELECTRICAL SPECIFICATIONS
• Sleek, low-profile design. Voltage Range: 15 - 32 volts DC peak.
• Addressable-analog communication. Standby Current (max. avg.): 300 μA
• Stable communication technique with noise immunity. LED Current (max.): 6.5 mA @ 24 VDC (“ON”).
• Low standby current.
• Two-wire SLC connection. Installation
• Compatible with FlashScan® and CLIP systems
FSI-851 Series plug-in detectors use a separate base to simplify
• Direct-dial entry of address 01– 159 for FlashScan loops, 01 installation, service, and maintenance. A special tool allows
– 99 for CLIP mode loops maintenance personnel to plug in and remove detectors without
• Optional remote, single-gang LED accessory (RA400Z). using a ladder.
• Dual LED design provides 360° viewing angle. Mount base on an electrical backbox which is at least 1.5" (3.81
• Visible bicolor LEDs blink green every time the detector is cm) deep. Suitable mounting base boxes include:
addressed, and illuminate steady red on alarm. • 4.0" (10.16 cm) square box.
• Remote test feature from the panel. • 3.5" (8.89 cm) or 4.0" (10.16 cm) octagonal box.
• Walk test with address display (an address of 121 will blink • Single-gang box (except relay or isolator base).
the detector LED: 12-(pause)-1) (FlashScan® systems only).
• With B501BH-2 or B501BHT-2 base, use a 4.0" (10.16 cm)
• Built-in functional test switch activated by external magnet. square box.
• Built-in tamper-resistant feature. • With B224RB or B224BI base, use a 3.5" (8.89 cm) octago-
• Sealed against back pressure. nal box, or a 4.0" (10.16 cm) octagonal or square box.
• Constructed of off-white Bayblend®, designed to commercial NOTES: 1) Because of the inherent supervision provided by the
standards, and offers an attractive appearance. SLC loop, end-of-line resistors are not required. Wiring “T-taps” or
• 94-5V plastic flammability rating. branches are permitted for Style 4 (Class “B”) wiring. 2) When
using relay or sounder bases, consult install sheet DN-2243 (ISO-
• SEMS screws for wiring of the separate base. X) for device limitations between isolator modules and isolator
• Optional relay, isolator, or sounder bases. bases
• Listed to UL 268.
Agency Listings and Approvals
Specifications These listings and approvals apply to the modules specified in
Size: 2.0" (51 mm) high x 4.1" (10.4 cm) diameter installed in this document. In some cases, certain modules or applications
B501 base, 6.1" (15.5 cm) diameter installed in B710LP base. may not be listed by certain approval agencies, or listing may be
in process. Consult factory for latest listing status.
Shipping Weight: 5.4 oz. (153 g).
• UL Listed: S1115
Operating Temperature: 0°C to 49°C (32°F to 120°F).
• ULC Listed: CS308 (FSI-851A)
• CSFM: 7271-0028:201
dn-6934:a • 06/09/09 — Page 1 of 2

• MEA: 321-02-E
• Maryland State Fire Marshal: Permit #2140
• BSMI: CI313066760014
• Lloyd’s Register: 03/60011
• U.S. Coast Guard: 161.002/23/3 (AFP-200); 161.002/27/3
(AFP1010/AM2020); 161.002/42/1 (NFS-640)
• FM Approved
Product Line Information

NOTE: “A” suffix indicates ULC Listed model.
FSI-851: Low-profile intelligent ionization sensor. Must be
mounted to one of the bases listed below.
FSI-851A: Same as above but with ULC Listing.
INTELLIGENT BASES
B501: Flangeless mounting base.
B501A: Flangeless mounting base, ULC Listed.
B501BP: Flangeless mounting base, ULC Listed.
B710LP: Flanged mounting base.
B710LPA: Flanged mounting base, ULC Listed.
B710LPBP: Flanged mounting base.
B501BH-2: Plug-in System Sensor standard sounder detec-tor
base, steady tone. Includes B501 base.
B501BHT-2: Plug-in System Sensor temporal tone sounder
base.
B501BHA: Plug-in System Sensor standard sounder detec-tor
base, steady tone, with ULC Listing. Includes B501 base.
B501BHTA: Plug-in System Sensor temporal tone sounder
base, with ULC listing.
B224RB: Relay base.
B224RBA: Relay base, ULC Listed.
B224BI: Isolator base.
B224BIA: Isolator base, ULC Listed.
ACCESSORIES
F110: Retrofit replacement flange for older style base. Converts
older high profile base for use with FlashScan® detectors.
RA400Z(A): Remote LED annunciator. 3 – 32 VDC. Fits U.S.
single-gang electrical box. Supported by B710LP and B501(A)
base bases only.
SMK400E: Surface mounting kit provides for entry of surface
wiring conduit. For use with B501(A) base only.
RMK400(A): Recessed mounting kit. For use with B501(A)
base only.
SMB600-C: Surface mounting kit for use with B710LP.
BCK-200B: Black detector covers, box of 10.
M02-04-00: Test magnet.
M02-09-00: Test magnet with telescope stick.
XR2B: Detector removal tool. Allows installation and/or removal
of FlashScan® Series detector heads from base in high ceiling
installations.
T55-127-010: Detector removal tool without pole.
FlashScan® is a registered trademark of Honeywell International Inc.
XP-4: Extension pole for XR2B. Comes in three 5-ft. sections. Bayblend® is a registered trademark of Bayer Corporation.
©2009 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.
This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com
Page 2 of 2 — dn-6934:a • 06/09/09

Smoke Detector FSI-851 - 0

Uploaded by

Copyright:

Available Formats

Smoke Detector FSI-851 - 0

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Smoke Detector FSI-851 - 0

Uploaded by

Copyright:

Available Formats

dn-6934:a

are compatible with ONYX series and CLIP series intelligent

dn-6934:a • 06/09/09 — Page 1 of 2

Product Line Information

This document is not intended to be used for installation purposes.

Page 2 of 2 — dn-6934:a • 06/09/09

You might also like