The NOTIFIER SDX-751 (photo) and CPX-751 (ion) are ana- Contact factory. log, addressable, low-profile (height measures only 1.66"/ Optional SMOKE GUARD is 42.164 mm) smoke detectors designed for the NFS-3030, UL listed with the SDX-751. AM2020, AFP1010, NFS-640, AFP-400, AFP-300, AFP-200, and System 5000 (when equipped with an AIM-200 mod- ule). S1115 Because the SDX-751 and CPX-751 are addressable, the control panel can provide fire fighters with a pinpoint descrip- tion of where the fire is located. The SDX-751 and CPX- 751 are also analog devices. The control panel is capable of not only knowing the detector’s location but exactly how much smoke is in the chamber of the detector. The detec- tor may be set for different sensitivity settings appropriate to the environment of its location. Analog devices continually send obscuration values to the
4762pho1.jpg control panel. These values may be gathered so as to allow the control panel to determine if a detector has accumulated an excessive amount of dirt or dust. A “maintenance” re- quired indication allows the installer to clean the smoke SDX-751 with B710LP base detector before an unwanted false alarm occurs. The CPX-751 Intelligent Ionization Sensor incorporates a unique single-source chamber design to respond quickly and dependably to a broad range of fires. The SDX-751 Intelligent Photoelectric Sensor’s unique opti- cal sensing chamber is designed with superior signal to noise ratio. The optical chamber is engineered to sense the 4762pho2.jpg
presence of smoke produced by a wide range of combus-
tion sources.
FEATURES SDX-751 with B501 base
• Sleek, low-profile design (height only 1.66"/42.164 mm). • Common base for both photo and ion detectors. • Compatible with current SDX-551 and CPX-551. SPECIFICATIONS • Addressable-analog communication. Size: 1.66" (42.164 mm) high x 4.1" (104.140 mm) dia. • Stable communication technique with noise immunity. Shipping weight: 3.6 oz. (104 g). • Low standby current. Operating temperature: 0°C to 49°C (32°F to 120°F). • Rotary decade 01 to 99 address switches. UL listed velocity range: ION: 0 – 1500 fpm. PHOTO: 0 – • Optional remote, single-gang LED accessory (RA400Z). 4000 fpm. • Dual LED design provides 360° viewing angle. Relative humidity: 10% – 93% non-condensing. • Visible LEDs blink every time the detector is addressed, ELECTRICAL SPECIFICATIONS: and illuminate steady on alarm (LED blink is optional on Voltage range: 15 – 32 volts DC peak. the NFS-3030, AM2020, AFP1010, NFS-640, AFP-400, Standby current — ION: 200 µA @ 24 VDC (without com- AFP-300 and AFP-200). munication); 300 µA @ 24 VDC (one communication every • Built-in functional test switch activated by external mag- 5 seconds with LED enabled). net. Standby current — PHOTO: 230 µA @ 24 VDC (without • Optional relay, isolator, or sounder bases. communication); 330 µA @ 24 VDC (one communication • Listed to UL 268. every 5 seconds with LED enabled). LED current (maximum): 6.5 mA @ 24 VDC (“ON”).
This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact NOTIFIER. Phone: (203) 484-7161 FAX: (203) 484-7118
BASES AVAILABLE: ORDERING INFORMATION B710LP: 6.2" (157.48 mm) diameter. CPX-751 Low-profile intelligent ionization sensor. Must B501: 4.0" (101.6 mm) diameter. be mounted to one of the bases listed below. B501BH: Sounder base assembly. Includes B501 base. SDX-751 Low-profile intelligent photoelectronic sensor. Must be mounted to one of the bases listed B224RB Relay Base: Screw terminals: up to 14 AWG (2.0 below. mm²). Relay type: Form-C. Rating: 2.0 A @ 30 VDC resis- tive; 0.3 A @ 110 VDC inductive; 1.0 A @ 30 VDC inductive. BASES: Dimensions: 6.2" (157.48 mm) x 1.2" (30.48 mm). B710LP Standard U.S. Low-Profile base. B524BI Isolator Base: Dimensions: 6.2" (157.48 mm) x B501 Standard European flangeless base. 1.2" (30.48 mm). Maximum: 25 devices between isolator B501BH Sounder base, includes B501 base above. bases. B224RB Intelligent relay base. INSTALLATION B224BI Intelligent isolator base. Isolates SLC from loop The CPX-751 and SDX-751 plug-in detectors use a sepa- shorts. rate base to simplify installation, service, and maintenance. ACCESSORIES: A special tool allows maintenance personnel to plug in and SDG-773 Smoke Detector Guard. For use with SDX-751 remove detectors without using a ladder. only. Mount base on a box which is at least 1.5" (38.1 mm) deep. F110 Retrofit replacement flange for BX-501 base. Suitable mounting base boxes include: RA400Z* Remote LED annunciator. 3 – 32 VDC. Fits • 4" (101.6 mm) square box. U.S. single-gang electrical box. • 3-1/2" (88.9 mm) or 4" (101.6 mm) octagonal box. MOD400R Detector sensitivity test tool. Use with most • Single-gang box (except relay or isolator base). analog or digital multimeters. Satisfies re- quirement of NFPA 72 for sensitivity testing. SMOKE GUARD SMK400 Surface mounting kit provides for entry of sur- Cover: 16 gauge perforated steel (3/16" [4.7625 mm] dia. face wiring conduit. For use with B501 base perforations on 1/4" [6.35 mm] staggered centers). 51% open. only. SDG-773 is 3" (76.2 mm) deep by 7" (177.8 mm) wide. M02-04-01 Test magnet. Frame: 3/4" x 3/4" (19.05 x 19.05 mm) angle, 14 gauge M02-09-00 Test magnet with telescope stick. solid steel. XR-2 Detector removal tool. Allows installation and/ All guards are supplied with the following: or removal of 700 Series detector heads from 1) Guards fasten to mounting frame with No. 10/24 x 3/8" base in high ceiling installations. (9.525 mm) long Allen-head screws (10/24 spanner-head XP-4 Extension pole for XR-2. Comes in three five- screws and tool option at extra cost). foot sections. 2) Standard finish: “Cool Tan” baked enamel. *Supported by B710LP and B501 bases only. NOTIFIER® is a registered trademark of Honeywell International Inc.
