Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Datasheet 17

Download as pdf or txt
Download as pdf or txt
You are on page 1of 58

SPI NOR PN25F16

PN25F16
16M-BIT SERIAL FLASH MEMORY

Datasheet

Sep. 2015

NOTE: INFORMATION IN THIS PRODUCT SPECIFICATION IS SUBJECT TO CHANGE AT ANYTIME


WITHOUT NOTICE, ALL PRODUCT SPECIFICATIONS ARE PROVIDED FOR REFERENCE ONLY.TO
ANY INTELLECTUAL, PROPERTY RIGHTS IN PARAGON TECHNOLOGY LIMITED. ALL

INFORMATION IN THIS DOCUMENT IS PROVIDED.Web: www.paragontech.cn

A 1.3
SPI NOR PN25F16
1. Description
The PN25F16 is a 16M-bit (2M-byte) Serial Flash memory, with advanced write protection mechanisms. The
PN25F16 supports the standard Serial Peripheral Interface (SPI).
The PN25F16 can be programmed 1 to 256 bytes at a time, using the Page Program instruction. It is designed to
allow either single Sector/Block at a time or full chip erase operation. The PN25F16 can be configured to protect
part of the memory as the software protected mode. The device can sustain a minimum of 100K program/erase
cycles on each sector or block.

2. FEATURES
•Serial Peripheral Interface(SPI) •Software/Hardware Write Protection
–Standard SPI: CLK, /CS, SI, SO, /WP, /HOLD –3x256-Byte Security Registers with OTP Lock
–Dual SPI: CLK, /CS, IO0, IO1, /WP, /HOLD –Enable/Disable protection with WP Pin
–Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3 –Write protect all/portion of memory via software
–Top or Bottom, Sector or Block selection
•Read
–Normal Read (Serial): 50MHz clock rate •Single Supply Voltage
–Fast Read (Serial): 108MHz clock rate –Full voltage range: 2.7~3.6V
–Dual/Quad (Multi-I/O) Read: 108MHz clock rate
•Temperature Range
•Program –Commercial (0℃ to +70℃)
–Serial-input Page Program up to 256bytes –Industrial (-40℃ to +85℃)
–Program Suspend and Resume
•Cycling Endurance/Data Retention
•Erase –Typical 100k Program-Erase cycles on any sector
–Block erase (64/32 KB) –Typical 20-year data retention at +55℃
–Sector erase (4 KB)
–Chip erase
–Erase Suspend and Resume

•Program/Erase Speed
–Page Program time: 0.7ms typical
–Sector Erase time: 60ms typical
–Block Erase time: 0.2/0.4s typical
–Chip Erase time: 15s typical

•Flexible Architecture
–Sector of 4K-byte
–Block of 32/64K-byte

• Low Power Consumption


–20mA maximum active current
–5uA maximum power down current

A 1.3
SPI NOR PN25F16

3. Packaging Type

4. Pin Configurations
Pin Name I/O Description
/CS I Chip Select
Serial Output for single bit data Instructions. IO1 for Dual or Quad
SO (IO1) I/O Instructions.
Write Protect in single bit or Dual data Instructions. IO2 in Quad mode.
/WP (IO2) I/O The signal has an internal pull-up resistor and may be left unconnected in
the host system if not used for Quad Instructions.
VSS Ground
Serial Input for single bit data Instructions. IO0 for Dual or Quad
SI (IO0) I/O Instructions.
CLK I Serial Clock
Hold (pause) serial transfer in single bit or Dual data Instructions. IO3 in
/HOLD (IO3) I/O Quad-I/O mode. The signal has an internal pull-up resistor and may be left
unconnected in the host system if not used for Quad Instructions.
VCC Core and I/O Power Supply

A 1.3
SPI NOR PN25F16
5.Block Diagram

Figure 1 PN25F16 Serial Flash Memory Block Diagram


6.Pin description
During all operations, VCC must be held stable and within the specified valid range: VCC(min) to VCC(max).

Chip Select (/CS)


The chip select signal indicates when a instruction for the device is in process and the other signals are relevant for
the memory device. When the /CS signal is at the logic high state, the device is not selected and all input signals are
ignored and all output signals are high impedance. Unless an internal Program, Erase or Write Status Registers
embedded operation is in progress, the device will be in the Standby Power mode. Driving the /CS input to logic low
state enables the device, placing it in the Active Power mode. After Power Up, a falling edge on /CS is required prior
to the start of any instruction.

Serial Clock (CLK)


This input signal provides the synchronization reference for the SPI interface. Instructions, addresses, or data input
are latched on the rising edge of the CLK signal. Data output changes after the falling edge of CLK.

Serial Input (SI) /IO0


This input signal is used to transfer data serially into the device. It receives instructions, addresses, and data to be
programmed. Values are latched on the rising edge of serial SCK clock signal.
SI becomes IO0 an input and output during Dual and Quad Instructions for receiving instructions, addresses, and

A 1.3
SPI NOR PN25F16
data to be programmed (values latched on rising edge of serial SCK clock signal) as well as shifting out data (on the
falling edge of SCK).

Serial Data Output (SO)/IO1


This output signal is used to transfer data serially out of the device. Data is shifted out on the falling edge of the
serial SCK clock signal.

SO becomes IO1 an input and output during Dual and Quad Instructions for receiving instructions, addresses, and
data to be programmed (values latched on rising edge of serial SCK clock signal) as well as shifting out data (on the
falling edge of SCK).

Write Protect (/WP)/IO2


When /WP is driven Low (VIL), while the Status Register Protect bits (SRP1 and SRP0) of the Status Registers (SR2[0]
and SR1[7]) are set to 0 and 1 respectively, it is not possible to write to the Status Registers. This prevents any
alteration of the Status Registers. As a consequence, all the data bytes in the memory area that are protected by
the Block Protect, TB, SEC, and CMP bits in the status registers, are also hardware protected against data
modification while /WP remains Low. The /WP function is not available when the Quad mode is enabled (QE) in
Status Register 2 (SR2[1]=1).

The /WP function is replaced by IO2 for input and output during Quad mode for receiving addresses, and data to be
programmed (values are latched on rising edge of the SCK signal) as well as shifting out data (on the falling edge of
SCK). /WP has an internal pull-up resistance; when unconnected; /WP is at VIH and may be left unconnected in the
host system if not used for Quad mode.

HOLD (/HOLD)/IO3
The /HOLD signal goes low to stop any serial communications with the device, but doesn’t stop the operation of
write status register, programming, or erasing in progress.The operation of HOLD, need /CS keep low, and starts on
falling edge of the /HOLD signal, with CLK signal being low (if CLK is not being low, HOLD operation will not start
until CLK being low). The HOLD condition ends on rising edge of /HOLD signal with CLK being low (If CLK is not being
low, HOLD operation will not end until CLK being low).

The Hold condition starts on the falling edge of the Hold (/HOLD) signal, provided that this coincides with SCK being
at the logic low state. If the falling edge does not coincide with the SCK signal being at the logic low state, the Hold
condition starts whenever the SCK signal reaches the logic low state. Taking the /HOLD signal to the logic low state
does not terminate any Write, Program or Erase operation that is currently in progress.

VCC Power Supply


VCC is the supply voltage. is the single voltage used for all device functions including read, program, and erase.

VSS Ground
VSS is the reference for the VCC supply voltage.

A 1.3
SPI NOR PN25F16
7. Memory organization
The PN25F16 array is organized into 2048 programmable pages of 256-bytes each. Up to 256 bytes can be
programmed (bits are programmed from 1 to 0) at a time. Pages can be erased in groups of 16 (4KB sector erase),
groups of 256 (64KB block erase) or the entire chip (chip erase). The PN25F16 has 128 erasable sectors and 8
erasable 64-k byte blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require
data and parameter storage.

Table 2. Block/Sector Addresses of PN25F16


Memory Block(64k Block(32k Sector
Density byte) byte) Sector No. Size(KB) Address range

Sector 0 4 000000h-000FFFh
Half block 0 : : :

Sector 7 4 007000h-007FFFh
Block 0
Sector 8 4 008000h-008FFFh
Half block 1 : :
4
Sector 15 4 00F000h-00FFFFh
Sector 16 4 010000h-010FFFh
Half block 2 : : :

Sector 23 4 017000h-017FFFh
Block 1
Sector 24 4 018000h-018FFFh
Half block 3 : : :

Sector 31 4 01F000h-01FFFFh
16Mbit : : : : :

Sector 480 4 1E0000h-1E0FFFh


Half block 60 : : :

Sector 487 4 1E7000h-1E7FFFh


Block 30
Sector 488 4 1E8000h-1E8FFFh
Half block 61 : : :

Sector 495 4 1EF000h-1EFFFFh


Sector 496 4 1F0000h-1F0FFFh
Half block 62 : : :

Sector 503 4 1F7000h-1F7FFFh


Block 31
Sector 504 4 1F8000h-1F8FFFh
Half block 63 : : :

Sector 511 4 1FF000h-1FFFFFh


1. Block = Uniform Block, and the size is 64K bytes.
2. Half block = Half Uniform Block, and the size is 32k bytes.
3. Sector = Uniform Sector, and the size is 4K bytes.

A 1.3
SPI NOR PN25F16
8. Device operation
8.1 Standard SPI Instructions
The PN25F16 features a serial peripheral interface on 4 signals bus: Serial Clock (CLK), Chip Select (/CS), Serial Data
Input (SI) and Serial Data Output (SO). Both SPI bus mode 0 and 3 are supported. Input data is latched on the rising
edge of CLK and data shifts out on the falling edge of CLK.

8.2 Dual SPI Instructions


The PN25F16 supports Dual SPI operation when using the “Dual Output Fast Read” and “Dual I/O Fast Read” (3BH
and BBH) instructions. These instructions allow data to be transferred to or from the device at two times the rate of
the standard SPI. When using the Dual SPI instruction the SI and SO pins become bidirectional I/O pins: IO0 and IO1.

8.3 Quad SPI Instructions


The PN25F16 supports Quad SPI operation when using the “Quad Output Fast Read”, “Quad I/O Fast Read” (6BH,
EBH) instructions. These instructions allow data to be transferred t-o or from the device at four times the rate of the
standard SPI. When using the Quad SPI instruction the SI and SO pins become bidirectional I/O pins: IO0 and IO1,
and /WP and /HOLD pins become IO2 and IO3. Quad SPI instructions require the non-volatile Quad Enable bit (QE)
in Status Register-2 to be set.

8.4 Hold
For dard SPI operation, the HOLD# signal allows the PN25F16 operation to be paused while it is actively selected
(when CS# is low). The HOLD# function may be useful in cases where the SPI data and clock signals are shared with
other devices. For example, consider if the page buffer was only partially written when a priority interrupt requires
use of the SPI bus. In this case the HOLD# function can save the state of the instruction and the data in the buffer so
programming can resume where it left off once the bus is available again.
To initiate a HOLD# condition, the device must be selected with CS# low. A HOLD# condition will activate on the
falling edge of the HOLD# signal if the CLK signal is already low. If the CLK is not already low the HOLD# condition
will activate after the next falling edge of CLK. The HOLD# condition will terminate on the rising edge of the HOLD#
signal if the CLK signal is already low. If the CLK is not already low the HOLD# condition will terminate after the next
falling edge of CLK. During a HOLD# condition, the Serial Data Output (DO) is high impedance, and Serial Data Input
(DI) and Serial Clock (CLK) are ignored. The Chip Select (CS#) signal should be kept active (low) for the full duration
of the HOLD# operation to avoid resetting the internal logic state of the device.

Figure 3 Hold Condition Waveform

A 1.3
SPI NOR PN25F16
9. Operation Features

9.1 Supply Voltage

9.1.1 Operating Supply Voltage


Prior to selecting the memory and issuing instructions to it, a valid and stable VCC voltage within the specified
[VCC(min), VCC(max)] range must be applied (see operating ranges of page 50). In order to secure a stable DC
supply voltage, it is recommended to decouple the VCC line with a suitable capacitor (usually of the order of 10 nF
to 100 nF) close to the VCC/VSS package pins. This voltage must remain stable and valid until the end of the
transmission of the instruction and, for a Write instruction, until the completion of the internal write cycle (tW).

9.1.2 Power-up Conditions


When the power supply is turned on, VCC rises continuously from VSS to VCC. During this time, the Chip Select (/CS)
line is not allowed to float but should follow the VCC voltage, it is therefore recommended to connect the /CS line
to VCC via a suitable pull-up resistor.

In addition, the Chip Select (/CS) input offers a built-in safety feature, as the /CS input is edge sensitive as well as
level sensitive: after power-up, the device does not become selected until a falling edge has first been detected on
Chip Select (/CS). This ensures that Chip Select (/CS) must have been High, prior to going Low to start the first
operation.

9.1.3 Device Reset


In order to prevent inadvertent Write operations during power-up (continuous rise of VCC), a power on reset (POR)
circuit is included. At Power-up, the device does not respond to any instruction until VCC has reached the power on
reset threshold voltage (this threshold is lower than the minimum VCC operating voltage defined in operating
ranges of page 50).When VCC has passed the POR threshold, the device is reset.

9.1.4 Power-down
At Power-down (continuous decrease in VCC), as soon as VCC drops from the normal operating voltage to below the
power on reset threshold voltage, the device stops responding to any instruction sent to it. During Power-down, the
device must be deselected (Chip Select (/CS) should be allowed to follow the voltage applied on VCC) and in
Standby Power mode (that is there should be no internal Write cycle in progress).

9.2 Active Power and Standby Power Modes


When Chip Select (/CS) is Low, the device is selected, and in the Active Power mode. The device consumes ICC.
When Chip Select (/CS) is High, the device is deselected. If a Write cycle is not currently in progress, the device then
goes in to the Standby Power mode, and the device consumption drops to ICC1.

A 1.3
SPI NOR PN25F16
9.3 Hold Condition
The Hold (/HOLD) signal is used to pause any serial communications with the device without resetting the clocking
sequence. During the Hold condition, the Serial Data Output (SO) is high impedance, and Serial Data Input (SI) and
Serial Clock (CLK) are Don’t Care. To enter the Hold condition, the device must be selected, with Chip Select (/CS)
Low. Normally, the device is kept selected, for the whole duration of the Hold condition. Deselecting the device
while it is in the Hold condition, has the effect of resetting the state of the device, and this mechanism can be used
if it is required to reset any processes that had been in progress.The Hold condition starts when the Hold (/HOLD)
signal is driven Low at the same time as Serial Clock (CLK) already being Low (as shown in Figure 4).
The Hold condition ends when the Hold (HOLD) signal is driven High at the same time as Serial Clock (C) already
being Low. Figure 4 also shows what happens if the rising and falling edges are not timed to coincide with Serial
Clock (CLK) being Low.
Figure 4. Hold condition activation
/CS

CLK

HOLD /

HOLD HOLD

9.4 Status Register


9.4.1 Status Register Table
See Table 3 and Table 4 for detail description of the Status Register bits. Status Register-2 (SR2) and Status
Register-1 (SR1) can be used to provide status on the availability of the Flash memory array, if the device is write
enabled or disabled the state of write protection, Quad SPI setting, Security Register lock status, and Erase/Program
Suspend status.
Table 3. Status Register-2 (SR2)
Default
BIT Name Function Value Description
Suspend 0 = Erase/Program not suspended
7 SUS 0
Status 1 = Erase/Program suspended
Complement 0 = Normal Protection Map 1 =
6 CMP Protect 0 Inverted Protection Map
5 LB3 Security 0 OTP Lock Bits 3:1 for Security Registers 3:1
4 LB2 Register 0 0 = Security Register not protected
3 LB1 0
Lock Bits 1 = Security Register protected
2 Reserved Reserved 0
0 = Quad Mode Not Enabled, the /WP pin and /HOLD are
Quad enabled.
1 QE 0 1 = Quad Mode Enabled, the IO2 and IO3 pins are enabled,
Enable
and /WP and /HOLD functions are disabled

0 = SRP0 selects whether /WP input has effect on


Status
protection of the status register
0 SRP1 Resister 0
1 = SRP0 selects Power Supply Lock Down or OTP Lock
Protect 1 Down mode

A 1.3
SPI NOR PN25F16
Table 4. Status Register-1 (SR1)
Default
BIT Name Function Description
Value
0 = /WP input has no effect or Power Supply Lock
Status Down mode.
7 SRP0 Resister 0 1 = /WP input can protect the Status Register or
OTP Lock Down.
Protect 0

Sector/Block 0 = BP2-BP0 protect 64KB blocks


6 SEC 0
Protect 1 = BP2-BP0 protect 4KB sectors
Top/Bottom 0 = BP2-BP0 protect from the Top down
5 TB Protect 0 1 = BP2-BP0 protect from the Bottom up
4 BP2 0
Block Protect 000b = No protection
3 BP1 Bits 0
See Table 6 and Table 7 for protection ranges
2 BP0 0
Write Enable 0 = Not Write Enabled, no embedded operation can
1 WEL Latch 0 start
1 = Write Enabled, embedded operation can start
Write in 0 = Not Busy, no embedded operation in progress
0 WIP Progress 0
Status 1 = Busy, embedded operation in progress

9.4.2 The Status and Control Bits

9.4.2.1 WIP bit


The Write in Progress (WIP) bit indicates whether the memory is busy in program/erase/write status register
progress. When WIP bit sets to 1, means the device is busy in program/erase/write status register progress, when
WIP bit sets 0, means the device is not in program/erase/write status register progress.

9.4.2.2 WEL bit


The Write Enable Latch bit indicates the status of the internal Write Enable Latch. When set to 1 the internal Write
Enable Latch is set, when set to 0 the internal Write Enable Latch is reset and no Write Status Register, Program or
Erase instruction is accepted.

9.4.2.3 SEC, TB, BP2, BP1, BP0 bits


The Block Protect (SEC, TB, BP2, BP1, BP0) bits are non-volatile. They define the size of the area to be software
protected against Program and Erase instructions. These bits are written with the Write Status Register instruction.
When the Block Protect (SEC, TB, BP2, BP1, BP0) bits are set to 1, the relevant memory area (as defined in Table 6
and Table 7).becomes protected against Page Program, Sector Erase and Block Erase instructions. The Block
Protect (SEC, TB, BP2, BP1, BP0) bits can be written provided that the Hardware Protected mode has not been set.

A 1.3
SPI NOR PN25F16
9.4.2.4 SRP1,SRP0 bits

The Status Register Protect (SRP1 and SRP0) bits are non-volatile Read/Write bits in the status register. The SRP
bits control the method of write protection: software protection, hardware protection, power supply lock-down
or one time programmable protection.

9.1.1.1 QEbit

The Quad Enable (QE) bit is a non-volatile Read/Write bit in the Status Register that allows Quad operation. When
the QE bit is set to 0 (Default) the /WP pin and /HOLD pin are enable. When the QE pin is set to 1, the Quad IO2 and
IO3 pins are enabled. (The QE bit should never be set to 1 during standard SPI or Dual SPI operation if the /WP or
/HOLD pins directly to the power supply or ground).

9.4.2.6 LB3/LB2/LB1Bit

The LB bit is a non-volatile One Time Program (OTP) bit in Status Register that provide the write protect control and
status to the Security Registers. The default state of LB is 0, the security registers are unlocked. LB can be set to 1
individually using the Write Register instruction. LB is One Time Programmable, once it’s set to 1, the 256byte
Security Registers will become read-only permanently, LB3/2/1 for Security Registers 3:1.

9.4.2.7 CMPbit

The CMP bit is a non-volatile Read/Write bit in the Status Register2 (bit6). It is used in conjunction the SEC-BP0 bits
to provide more flexibility for the array protection. Please see the Status registers Memory Protection table for
details. The default setting is CMP=0.

9.4.2.8 SUSbit

The SUS bit is a read only bit in the status register2 (bit7) that is set to 1 after executing an Erase/Program Suspend
(75H) instruction. The SUS bit is cleared to 0 by Erase/Program Resume (7AH) instruction as well as a power-down,
power-up cycle.

A 1.3
SPI NOR PN25F16
9.4.3 Status Register Protect Table

Table 5. Status Register protect Table


SRP1 SRP0 /WP Status Register Description

Software The Status Register can be written to after a Write


0 0 X
Protected Enable instruction, WEL=1.(Factory Default)
Hardware /WP=0, the Status Register locked and cannot be
0 1 0
Protected written.
Hardware /WP=1, the Status Register is unlocked and can be
0 1 1 Unprotected written to after a Write Enable instruction, WEL=1.
Status Register is protected and cannot be written
Power Supply
1 0 X to again until the next Power-Down, Power-Up cycle.
Lock-Down(1)
One Time Status Register is permanently protected and cannot
1 1 X be written to.
Program (2)
Notes:

1.When SRP1, SRP0= (1, 0), a Power-Down, Power-Up cycle will change SRP1, SRP0 to (0, 0) state.

2.The One time Program feature is available upon special order. Please contact Paragon Microelectronics for

details.

9.4.4 Write Protect Features

1. Software Protection: The Block Protect (SEC, TB, BP2, BP1, BP0) bits define the section of the memory

array that can be read but not change.

2. Hardware Protection: /WP going low to protected the BP0~SEC bits and SRP0~1 bits.

3. Deep Power-Down: In Deep Power-Down Mode, all instructions are ignored except the Release from

deep Power-Down Mode instruction.

4. Write Enable: The Write Enable Latch (WEL) bit must be set prior to every Page Program, Sector Erase,

Block Erase, Chip Erase, Write Status Register and Erase/Program Security Registers instruction.

A 1.3
SPI NOR PN25F16
9.4.5 Status Register Memory Protection

9.4.5.1 Protect Table

Table 6. PN25F16 Status Register Memory Protection (CMP=0)

Status Register Content Memory Content

SEC TB BP2 BP1 BP0 Blocks Addresses Density Portion


X X 0 0 0 NONE NONE NONE NONE
0 0 0 0 1 31 1F0000H-1FFFFFH 64KB Upper 1/32
0 0 0 1 0 30 to 31 1E0000H-1FFFFFH 128KB Upper 1/16
0 0 0 1 1 28 to 31 1C0000H-1FFFFFH 256KB Upper 1/8
0 0 1 0 0 24 to 31 180000H-1FFFFFH 512KB Upper 1/4
0 0 1 0 1 16 to 31 100000H-1FFFFFH 1MB Upper 1/2
0 1 0 0 1 0 000000H-00FFFFH 64KB Lower 1/32
0 1 0 1 0 0 to 1 000000H-01FFFFH 128KB Lower 1/16
0 1 0 1 1 0 to 3 000000H-03FFFFH 256KB Lower 1/8
0 1 1 0 0 0 to 7 000000H-07FFFFH 512KB Lower 1/4
0 1 1 0 1 0 to 15 000000H-0FFFFFH 1MB Lower 1/2
X X 1 1 X 0 to 31 000000H-1FFFFFH 2MB ALL
1 0 0 0 1 31 1FF000H-1FFFFFH 4KB Top Block
1 0 0 1 0 31 1FE000H-1FFFFFH 8KB Top Block
1 0 0 1 1 31 1FC000H-1FFFFFH 16KB Top Block
1 0 1 0 X 31 1F8000H-1FFFFFH 32KB Top Block
1 1 0 0 1 0 000000H-000FFFH 4KB Bottom Block
1 1 0 1 0 0 000000H-001FFFH 8KB Bottom Block
1 1 0 1 1 0 000000H-003FFFH 16KB Bottom Block
1 1 1 0 X 0 000000H-007FFFH 32KB Bottom Block

A 1.3
SPI NOR PN25F16
Table 7. PN25F16 Status Register Memory Protection (CMP=1)

Status Register Content Memory Content

SEC TB BP2 BP1 BP0 Blocks Addresses Density Portion

X X 0 0 0 0 to 31 000000H-1FFFFFH 2MB ALL

0 0 0 0 1 0 to 30 000000H-1EFFFFH 1984KB Lower 31/32

0 0 0 1 0 0 to 29 000000H-1DFFFFH 1920KB Lower 15/16

0 0 0 1 1 0 to 27 000000H-1BFFFFH 1792KB Lower 7/8

0 0 1 0 0 0 to 23 000000H-17FFFFH 1536KB Lower 3/4

0 0 1 0 1 0 to 15 000000H-0FFFFFH 1MB Lower 1/2

0 1 0 0 1 1 to 31 010000H-1FFFFFH 1984KB Upper 31/32

0 1 0 1 0 2 to 31 020000H-1FFFFFH 1920KB Upper 15/16

0 1 0 1 1 4 to 31 040000H-1FFFFFH 1792KB Upper 7/8

0 1 1 0 0 8 to 31 080000H-1FFFFFH 1536KB Upper 3/4

0 1 1 0 1 16 to 31 100000H-1FFFFFH 1MB Upper 1/2

X X 1 1 X NONE NONE NONE NONE

1 0 0 0 1 0 to 31 000000H-1FEFFFH 2044KB L - 511/512

1 0 0 1 0 0 to 31 000000H-1FDFFFH 2040KB L - 255/256

1 0 0 1 1 0 to 31 000000H-1FBFFFH 2032KB L - 127/128

1 0 1 0 X 0 to 31 000000H-1F7FFFH 2016KB L - 63/64

1 1 0 0 1 0 to 31 001000H-1FFFFFH 2044KB U - 511/512

1 1 0 1 0 0 to 31 002000H-1FFFFFH 2040KB U - 255/256

1 1 0 1 1 0 to 31 004000H-1FFFFFH 2032KB U - 127/128

1 1 1 0 X 0 to 31 008000H-1FFFFFH 2016KB U - 63/64

A 1.3
SPI NOR PN25F16
10. Device ID
Three legacy Instructions are supported to access device identification that can indicate the manufacturer, device
type, and capacity (density). The returned data bytes provide the information as shown in the below table.

Table 8. PN25F16 ID Definition table

Operation Code M7-M0 ID15-ID8 ID7-ID0


9FH E0 40 15
90H E0 14
ABH 14

11. Instructions Description


All instructions, addresses and data are shifted in and out of the device, beginning with the most significant bit on
the first rising edge of CLK after /CS is driven low. Then, the one byte instruction code must be shifted in to the
device, most significant bit first on SI, each bit being latched on the rising edges of CLK.

See Table 9, every instruction sequence starts with a one-byte instruction code. Depending on the instruction, this
might be followed by address bytes, or by data bytes, or by both or none. /CS must be driven high after the last bit
of the instruction sequence has been shifted in. For the instruction of Read, Fast Read, Read Status Register or
Release from Deep Power Down, and Read Device ID, the shifted-in instruction sequence is followed by a data out
sequence. /CS can be driven high after any bit of the data-out sequence is being shifted out.

For the instruction of Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register, Write Enable,
Write Disable or Deep Power-Down instruction, /CS must be driven high exactly at a byte boundary, otherwise the
instruction is rejected, and is not executed. That is /CS must driven high when the number of clock pulses after /CS
being driven low is an exact multiple of eight. For Page Program, if at any time the input byte is not a full byte,
nothing will happen and WEL will not be reset.

A 1.3
SPI NOR PN25F16
Table 9. Instruction Set Table
Instruction Name Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6

Write Enable 06H


Write Disable 04H
Read Status 05H (S7-S0)
Register-1
Read Status 35H (S15-S8)
Register-2
Write Enable for
Volatile Status 50H
Register
Write Status Register 01H (S7-S0) (S15-S8)
Read Data 03H A23-A16 A15-A8 A7-A0 (D7-D0) Next byte
Fast Read 0BH A23-A16 A15-A8 A7-A0 dummy (D7-D0)
Dual Output Fast 3BH A23-A16 A15-A8 A7-A0 dummy (D7-D0)(1)
Read
A7-A0
Dual I/O Fast Read BBH A23-A8(2) M7-M0(2) (D7-D0)(1)
Quad Output Fast 6BH A23-A16 A15-A8 A7-A0 dummy (D7-D0)(3)
Read
A23-A0
Quad I/O Fast Read EBH M7-M0(4) dummy (D7-D0)(5)
Continuous Read FFH FFH
Reset
Page Program 02H A23-A16 A15-A8 A7-A0 (D7-D0) Next byte
Sector Erase 20H A23-A16 A15-A8 A7-A0
Block Erase(32K) 52H A23-A16 A15-A8 A7-A0
Block Erase(64K) D8H A23-A16 A15-A8 A7-A0
Chip Erase C7/60H
Program/Erase 75H
Suspend
Program/Erase 7AH
Resume
Deep Power-Down B9H
Release From Deep
Power-Down, And ABH dummy dummy dummy (ID7-ID0)
Read Device ID
Release From Deep
Power-Down ABH
Manufacturer/ Device
90H dummy dummy 00H (M7-M0) (ID7-ID0)
ID
JEDEC ID 9FH (M7-M0) (ID15-ID8) (ID7-ID0)
Erase Security
Registers(6) 44H A23-A16 A15-A8 A7-A0
Program Security 42H A23-A16 A15-A8 A7-A0 (D7-D0) (D7-D0)
Registers(6)
Read Security 48H A23-A16 A15-A8 A7-A0 dummy (D7-D0)
Registers(6)

A 1.3
SPI NOR PN25F16
Notes:
1. Dual Output data
IO0 = (D6, D4, D2, D0) IO1 = (D7, D5, D3, D1)
2. Dual Input Address
IO0 = A22, A20, A18, A16, A14, A12, A10, A8, A6, A4, A2, A0, M6, M4, M2, M0 IO1 = A23, A21, A19, A17,
A15, A13, A11, A9, A7, A5, A3, A1, M7, M5, M3
3. Quad Output Data
IO0 = (D4, D0,…..)
IO1 = (D5, D1,…..)
IO2 = (D6, D2,…..)
IO3 = (D7, D3,…..)
4. Quad Input Address
IO0 = A20, A16, A12, A8, A4, A0, M4, M0 IO1 = A21, A17, A13, A9, A5,
A1, M5, M1
IO2 = A22, A18, A14, A10, A6, A2, M6, M2
IO3 = A23, A19, A15, A11, A7, A3, M7, M3
5. Fast Read Quad I/O Data
IO0 = (x, x, x, x, D4, D0,…)
IO1 = (x, x, x, x, D5, D1,…)
IO2 = (x, x, x, x, D6, D2,…)
IO3 = (x, x, x, x, D7, D3,…)
6. Security Registers Address:
Security Register0: A23-A16=00h, A15-A8=00h, A7-A0= Byte Address; Security Register1:
A23-A16=00h, A15-A8=01h, A7-A0= Byte Address; Security Register2: A23-A16=00h,
A15-A8=02h, A7-A0= Byte Address; Security Register3: A23-A16=00h, A15-A8=03h, A7-A0=
Byte Address;

Security Register 0 can be used to store the Flash Discoverable Parameters,


The feature is upon special order, please contact Paragon Microelectronics for details.

A 1.3
SPI NOR PN25F16

12.1 Configuration and Status

12.1.1 Write Enable (06H)

See Figure 5, the Write Enable instruction is for setting the Write Enable Latch bit. The Write Enable Latch bit must
be set prior to every Page Program, Sector Erase, Block Erase, Chip Erase and Write Status Register instruction. The
Write Enable instruction sequence: /CS goes low sending the Write Enable instruction /CS goes high.

Figure 5. Write Enable Sequence Diagram

12.1.2 Write Disable (04H)


See Figure 6, the Write Disable instruction is for resetting the Write Enable Latch bit. The Write Disable instruction
sequence: /CS goes low Sending the Write Disable instruction /CS goes high. The WEL bit is reset by following
condition: Power-up and upon completion of the Write Status Register, Page Program, Sector Erase, Block Erase and
Chip Erase instructions.

Figure 6. Write Disable Sequence Diagram

A 1.3
SPI NOR PN25F16
12.1.3 Read Status Register (05H or 35H)
See Figure 7 the Read Status Register (RDSR) instruction is for reading the Status Register. The Status Register may
be read at any time, even while a Program, Erase or Write Status Register cycle is in progress. When one of these
cycles is in progress, it is recommended to check the Write in Progress (WIP) bit before sending a new instruction to
the device. It is also possible to read the Status Register continuously. For instruction code “05H”, the SO will output
Status Register bits S7~S0. The instruction code “35H”, the SO will output Status Register bits S15~S8.

Figure 7. Read Status Register Sequence Diagram

12.1.4 Write Status Register (01H)


See Figure 8, the Write Status Register instruction allows new values to be written to the Status Register. Before it
can be accepted, a Write Enable instruction must previously have been executed. After the Write Enable instruction
has been decoded and executed, the device sets the Write Enable Latch (WEL).

The Write Status Register instruction has no effect on S15, S1 and S0 of the Status Register. /CS must be driven high
after the eighth or sixteen bit of the data byte has been latched in. If not, the Write Status Register instruction is not
executed. If /CS is driven high after eighth bit of the data byte, the CMP and QE and SRP1 bits will be cleared to 0.
As soon as /CS is driven high, the self-timed Write Status Register cycle (whose duration is tW) is initiated. While the
Write Status Register cycle is in progress, the Status Register may still be read to check the value of the Write in
Progress (WIP) bit. The Write in Progress (WIP) bit is 1 during the self-timed Write Status Register cycle, and is 0
when it is completed. When the cycle is completed, the Write Enable Latch is reset.

The Write Status Register instruction allows the user to change the values of the Block Protect (SEC, TB, BP2, BP1,
BP0) bits, to define the size of the area that is to be treated as read-only, as defined in Table 3. The Write Status
Register instruction also allows the user to set or reset the Status Register Protect (SRP1 and SRP0) bits in
accordance with the Write Protect (/WP) signal. The Status Register Protect (SRP1 and SRP0) bits and Write Protect
(/WP) signal allow the device to be put in the Hardware Protected Mode. The Write Status Register instruction is
not executed once the Hardware Protected Mode is entered.

A 1.3
SPI NOR PN25F16
Figure 8. Write Status Register Sequence Diagram

12.1.5 Write Enable for Volatile Status Register (50H)


See Figure 9, the non-volatile Status Register bits can also be written to as volatile bits. During power up reset, the
non-volatile Status Register bits are copied to a volatile version of the Status Register that is used during device
operation. This gives more flexibility to change the system configuration and memory protection schemes quickly
without waiting for the typical non-volatile bit write cycles or affecting the endurance of the Status Register
non-volatile bits. To write the volatile version of the Status Register bits, the Write Enable for Volatile Status
Register (50h) instruction must be issued prior to each Write Status Registers (01h) instruction. Write Enable for
Volatile Status Register instruction will not set the Write Enable Latch bit, it is only valid for the next following Write
Status Registers instruction, to change the volatile Status Register bit values.

Figure 9. Write Enable for Volatile Status Register Sequence Diagram

A 1.3
SPI NOR PN25F16
12.2 Read Instructions

12.1.1Read Data (03H)

See Figure 10, the Read Data Bytes (READ) instruction is followed by a 3-byte address (A23-A0), each bit being
latched-in during the rising edge of CLK. Then the memory content, at that address, is shifted out on SO, each bit
being shifted out, at a Max frequency fR, during the falling edge of CLK. The address is automatically incremented to
the next higher address after each byte of data is shifted out allowing for a continuous stream of data. This means
that the entire memory can be accessed with a single command as long as the clock continues. The command is
completed by driving /CS high. The whole memory can be read with a single Read Data Bytes (READ) instruction.
Any Read Data Bytes (READ) instruction, while an Erase, Program or Write cycle is in progress, is rejected without
having any effects on the cycle that is in progress. Normal read mode running up to 50MHz.

Figure 10. Read Data Bytes Sequence Diagram

A 1.3
SPI NOR PN25F16
12.1.2 Fast Read (0BH)

See Figure 11, the Read Data Bytes at Higher Speed (Fast Read) instruction is for quickly reading data out. It is
followed by a 3-byte address (A23-A0) and a dummy byte, each bit being latched-in during the rising edge of CLK.
Then the memory content, at that address, is shifted out on SO, each bit being shifted out, at a Max frequency fc,
during the falling edge of CLK. The first byte addressed can be at any location. The address is automatically
incremented to the next higher address after each byte of data is shifted out.

Figure 11. Fast Read Sequence Diagram

A 1.3
SPI NOR PN25F16
12.1.3 Dual Output Fast Read (3BH)
See Figure 12, the Dual Output Fast Read instruction is followed by 3-byte address (A23-A0) and a dummy byte,
each bit being latched in during the rising edge of CLK, then the memory contents are shifted out 2-bit per clock
cycle from SI and SO. The first byte addressed can be at any location. The address is automatically incremented to
the next higher address after each byte of data is shifted out.

Figure 12. Dual Output Fast Read Sequence Diagram

A 1.3
SPI NOR PN25F16
12.1.4 Quad Output Fast Read (6BH)
See Figure 13, the Quad Output Fast Read instruction is followed by 3-byte address (A23-A0) and a dummy byte,
each bit being latched in during the rising edge of CLK, then the memory contents are shifted out 4-bit per clock
cycle from IO3, IO2, IO1 and IO0. The first byte addressed can be at any location. The address is automatically
incremented to the next higher address after each byte of data is shifted out.

Figure 13. Quad Output Fast Read Sequence Diagram

A 1.3
SPI NOR PN25F16
12.1.5 Dual I/O Fast Read (BBH)

See Figure 14, the Dual I/O Fast Read instruction is similar to the Dual Output Fast Read instruction but with the
capability to input the 3-byte address (A23-0) and a “Continuous Read Mode” byte 2-bit per clock by SI and SO, each
bit being latched in during the rising edge of CLK, then the memory contents are shifted out 2-bit per clock cycle
from SI and SO. The first byte addressed can be at any location. The address is automatically incremented to the
next higher address after each byte of data is shifted out.

Figure 14. Dual I/O Fast Read Sequence Diagram (Initial command or previous M5-4≠10)

A 1.3
SPI NOR PN25F16
12.1.6 Dual I/O Fast Read with “Continuous Read Mode”
The Fast Read Dual I/O command can further reduce instruction overhead through setting the “Continuous Read
Mode” bits (M7-0) after the input Address bits (A23-0), as shown in Figure 14. The upper nibble of the (M7-4)
controls the length of the next Fast Read Dual I/O command through the inclusion or exclusion of the first byte
instruction code. The lower nibble bits of the (M3-0) are don’t care (“x”). However, the IO pins should be
high-impedance prior to the falling edge of the first data out clock. If the “Continuous Read Mode” bits M5-4 = (1,0),
then the next Fast Read Dual I/O command (after /CS is raised and then lowered) does not require the BBH
instruction code, as shown in Figure 15. This reduces the command sequence by eight clocks and allows the Read
address to be immediately entered after /CS is asserted low. If the “Continuous Read Mode” bits M5-4 do not equal
to (1,0), the next command (after /CS is raised and then lowered) requires the first byte instruction code, thus
returning to normal operation. A “Continuous Read Mode” Reset command can also be used to reset (M7-0) before
issuing normal commands (see Continuous Read Mode Reset (FFH or FFFFH)).

Figure 15. Dual I/O Fast Read Sequence Diagram (Previous command set M5-4 =10)

A 1.3
SPI NOR PN25F16
12.1.7 Quad I/O Fast Read (EBH)
See Figure 16, the Quad I/O Fast Read instruction is similar to the Dual I/O Fast Read instruction but with the
capability to input the 3-byte address (A23-0) and a “Continuous Read Mode” byte and 4-dummy clock 4-bit per
clock by IO0, IO1, IO3, IO4, each bit being latched in during the rising edge of CLK, then the memory contents are
shifted out 4-bit per clock cycle from IO0, IO1, IO2, IO3. The first byte addressed can be at any location. The address
is automatically incremented to the next higher address after each byte of data is shifted out. The Quad Enable bit
(QE) of Status Register must be set to enable for the Quad I/O Fast read instruction.

Figure 16. Quad I/O Fast Read Sequence Diagram (Initial command or previous M5-4≠10)

A 1.3
SPI NOR PN25F16
12.1.8 Quad I/O Fast Read with “Continuous Read Mode”
The Fast Read Quad I/O command can further reduce instruction overhead through setting the “Continuous Read
Mode” bits (M7-0) after the input Address bits (A23-0), as shown in Figure 16, The upper nibble of the (M7-4)
controls the length of the next Fast Read Quad I/O command through the inclusion or exclusion of the first byte
instruction code. The lower nibble bits of the (M3-0) are don’t care (“x”). However, the IO pins should be
high-impedance prior to the falling edge of the first data out clock. If the “Continuous Read Mode” bits M5-4 = (1,0),
then the next Fast Read Quad I/O command (after /CS is raised and then lowered) does not require the EBH
instruction code, as shown in Figure 17, This reduces the command sequence by eight clocks and allows the Read
address to be immediately entered after /CS is asserted low. If the “Continuous Read Mode” bits M5-4 do not equal
to (1,0), the next command (after /CS is raised and then lowered) requires the first byte instruction code, thus
returning to normal operation. A “Continuous Read Mode” Reset command can also be used to reset (M7-0) before
issuing normal commands (see Continuous Read Mode Reset (FFH or FFFFH)).

Figure 17. Quad I/O Fast Read Sequence Diagram (Previous command set M5-4 =10)

A 1.3
SPI NOR PN25F16
12.2.9 Continuous Read Mode Reset (FFH or FFFFH)
The “Continuous Read Mode” bits are used in conjunction with “Fast Read Dual I/O” and “Fast Read Quad I/O”
Instructions to provide the highest random Flash memory access rate with minimum SPI instruction overhead, thus
allowing more efficient XIP (execute in place) with this device family.

The “Continuous Read Mode” bits M7-0 are set by the Dual/Quad I/O Read Instructions. M5-4 are used to control
whether the 8-bit SPI instruction code (BBh or EBh) is needed or not for the next instruction. When M5-4 = (1,0),
the next instruction will be treated the same as the current Dual/Quad I/O Read instruction without needing the
8-bit instruction code; when M5-4 do not equal to (1,0), the device returns to normal SPI instruction mode, in which
all instructions can be accepted. M7-6 and M3-0 are reserved bits for future use, either 0 or 1 values can be used.

See Figure 18, the Continuous Read Mode Reset instruction (FFh or FFFFh) can be used to set M4 = 1, thus the
device will release the Continuous Read Mode and return to normal SPI operation.

To reset “Continuous Read Mode” during Quad I/O operation, only eight clocks are needed. The instruction is “FFh”.
To reset “Continuous Read Mode” during Dual I/O operation, sixteen clocks are needed to shift in instruction
“FFFFh

Figure 18. Continuous Read Mode Reset Sequence Diagram

A 1.3
SPI NOR PN25F16
12.2.10 Fast Read Quad I/O with “8/16/32/64-Byte Wrap Around”
The Fast Read Quad I/O instruction can also be used to access a specific portion within a page by issuing a “Set Burst
with Wrap” (77h) instruction prior to EBh. The “Set Burst with Wrap” (77h) instruction can either enable or disable
the “Wrap Around” feature for the following EBh instructions. When “Wrap Around” is enabled, the data being
accessed can be limited to either an 8, 16, 32 or 64-byte section of a 256-byte page. The output data starts at the
initial address specified in the instruction, once it reaches the ending boundary of the 8/16/32/64-byte section, the
output will wrap around to the beginning boundary automatically until /CS is pulled high to terminate the
instruction.

The Burst with Wrap feature allows applications that use cache to quickly fetch a critical address and then fill the
cache afterwards within a fixed length (8/16/32/64-byte) of data without issuing multiple read instructions.

The “Set Burst with Wrap” instruction allows three “Wrap Bits”, W6-4 to be set. The W4 bit is used to enable or
disable the “Wrap Around” operation while W6-5 are used to specify the length of the wrap around section within a
page.

Similar to a Quad I/O instruction, the Set Burst with Wrap instruction is initiated by driving the /CS pin low and then
shifting the instruction code “77h” followed by 24 dummy bits and 8 “Wrap Bits”, W7-0. Wrap bit W7 and the lower
nibble W3-0 are not used.

Once W6-4 is set by a Set Burst with Wrap instruction, all the following “Fast Read Quad I/O” and “Word Read Quad
I/O” instructions will use the W6-4 setting to access the 8/16/32/64-byte section within any page. To exit the “Wrap
Around” function and return to normal read operation, another Set Burst with Wrap instruction should be issued to
set W4=1. The default value of W4 upon power on is 1

W4 = 0 W4 =1 (DEFAULT)
W6 W5
Wrap Around Wrap Length Wrap Around Wrap Length

0 0 Yes 8-byte No N/A


0 1 Yes 16-byte No N/A
1 0 Yes 32-byte No N/A
1 1 Yes 64-byte No N/A

A 1.3
SPI NOR PN25F16
Figure 19. Set Burst with Wrap Command Sequence

A 1.3
SPI NOR PN25F16
12.2 ID and Security Instructions

12.2.1 Read Manufacture ID/ Device ID (90H)


See Figure 20, the Read Manufacturer/Device ID instruction is an alternative to the Release from
Power-Down/Device ID instruction that provides both the JEDEC assigned Manufacturer ID and the specific Device
ID.
The instruction is initiated by driving the /CS pin low and shifting the instruction code “90H” followed by a 24-bit
address (A23-A0) of 000000H. If the 24-bit address is initially set to 000001H, the Device ID will be read first.

Figure 20. Read Manufacture ID/ Device ID Sequence Diagram

A 1.3
SPI NOR PN25F16
12.2.2 JEDEC ID (9FH)
The JEDEC ID instruction allows the 8-bit manufacturer identification to be read, followed by two bytes of device
identification. The device identification indicates the memory type in the first byte, and the memory capacity of the
device in the second byte. JEDEC ID instruction while an Erase or Program cycle is in progress, is not decoded, and
has no effect on the cycle that is in progress. The JEDEC ID instruction should not be issued while the device is in
Deep Power-Down Mode.

See Figure 21, he device is first selected by driving /CS to low. Then, the 8-bit instruction code for the instruction is
shifted in. This is followed by the 24-bit device identification, stored in the memory, being shifted out on Serial Data
Output, each bit being shifted out during the falling edge of Serial Clock. The JEDEC ID instruction is terminated by
driving /CS to high at any time during data output. When /CS is driven high, the device is put in the Standby Mode.
Once in the Standby Mode, the device waits to be selected, so that it can receive, decode and execute instructions.

Figure 21. JEDEC ID Sequence Diagram

A 1.3
SPI NOR PN25F16
12.2.3 Deep Power-Down (B9H)

Although the standby current during normal operation is relatively low, standby current can be further reduced
with the Deep Power-down instruction. The lower power consumption makes the Deep Power-down (DPD)
instruction especially useful for battery powered applications (see ICC1 and ICC2). The instruction is initiated by
driving the /CS pin low and shifting the instruction code “B9h” as shown in Figure 22.

The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Deep Power down
instruction will not be executed. After /CS is driven high, the power-down state will entered within the time
duration of tDP. While in the power-down state only the Release from Deep Power-down / Device ID instruction,
which restores the device to normal operation, will be recognized. All other Instructions are ignored. This includes
the Read Status Register instruction, which is always available during normal operation. Ignoring all but one
instruction also makes the Power Down state a useful condition for securing maximum write protection. The device
always powers-up in the normal operation with the standby current of ICC1.

Figure 22. Deep Power-Down Sequence Diagram

A 1.3
SPI NOR PN25F16
12.2.4 Release from Deep Power-Down/Read Device ID (ABH)
The Release from Power-Down or Device ID instruction is a multi-purpose instruction. It can be used to release the
device from the Power-Down state or obtain the devices electronic identification (ID) number.

See Figure 23a, to release the device from the Power-Down state, the instruction is issued by driving the /CS pin
low, shifting the instruction code “ABH” and driving /CS high Release from Power-Down will take the time duration
of tRES1 (See AC Characteristics) before the device will resume normal operation and other instruction are accepted.
The /CS pin must remain high during the tRES1 time duration.

When used only to obtain the Device ID while not in the Power-Down state, the instruction is initiated by driving
the /CS pin low and shifting the instruction code “ABH” followed by 3-dummy byte. The Device ID bits are then
shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in Figure 23b. The Device ID
value for the PN25F16 is listed in Manufacturer and Device Identification table. The Device ID can be read
continuously. The instruction is completed by driving /CS high.

When used to release the device from the Power-Down state and obtain the Device ID, the instruction is the same
as previously described, and shown in Figure 23b, except that after /CS is driven high it must remain high for a time
duration of tRES2 (See AC Characteristics). After this time duration the device will resume normal operation and
other instruction will be accepted. If the Release from Power-Down/Device ID instruction is issued while an Erase,
Program or Write cycle is in process (when WIP equal 1) the instruction is ignored and will not have any effects on
the current cycle.

Figure 23a. Release Power-Down Sequence Diagram

Figure 23b. Release Power-Down/Read Device ID Sequence Diagram

A 1.3
SPI NOR PN25F16
12.2.5 Read Security Registers (48H)

See Figure 24, the Read Security Registers instruction is similar to Fast Read instruction. The instruction is followed
by a 3-byte address (A23-A0) and a dummy byte, each bit being latched-in during the rising edge of CLK. Then the
memory content, at that address, is shifted out on SO, each bit being shifted out, at a Max frequency fC, during the
falling edge of CLK. The first byte addressed can be at any location. The address is automatically incremented to the
next higher address after each byte of data is shifted out. Once the A9-A0 address reaches the last byte of the
register (Byte 3FFH), it will reset to 000H, the instruction is completed by driving /CS high.

Address A23-A16 A15-A8 A7-A0


Security Registers 1 00H 01H Byte Address
Security Registers 2 00H 02H Byte Address
Security Registers 3 00H 03H Byte Address

Figure 24. Read Security Registers instruction Sequence Diagram

A 1.3
SPI NOR PN25F16
12.2.6 Erase Security Registers (44H)

The PN25F16 provides three 256-byte Security Registers which can be erased and programmed individually. These
registers may be used by the system manufacturers to store security and other important information separately
from the main memory array.

See Figure 25, the Erase Security Registers instruction is similar to Sector/Block Erase instruction. A Write Enable
instruction must previously have been executed to set the Write Enable Latch bit.

The Erase Security Registers instruction sequence: /CS goes low sending Erase Security Registers instruction /CS
goes high. /CS must be driven high after the eighth bit of the instruction code has been latched in otherwise the
Erase Security Registers instruction is not executed. As soon as /CS is driven high, the self-timed Erase Security
Registers cycle (whose duration is tSE) is initiated. While the Erase Security Registers cycle is in progress, the Status
Register may be read to check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1
during the self-timed Erase Security Registers cycle, and is 0 when it is completed. At some unspecified time before
the cycle is completed, the Write Enable Latch bit is reset. The Security Registers Lock Bit (LB) in the Status Register
can be used to OTP protect the security registers. Once the LB bit is set to 1, the Security Registers will be
permanently locked; the Erase Security Registers instruction will be ignored.

Address A23-A16 A15-A8 A7-A0


Security Registers 1 00H 01H Don’t Care

Security Registers 2 00H 02H Don’t Care


Security Registers 3 00H 03H Don’t Care

Figure 25. Erase Security Registers instruction Sequence Diagram

A 1.3
SPI NOR PN25F16
12.2.7 Program Security Registers (42H)
See Figure 26, the Program Security Registers instruction is similar to the Page Program instruction. It allows from 1
to 256 bytes Security Registers data to be programmed. A Write Enable instruction must previously have been
executed to set the Write Enable Latch bit before sending the Program Security Registers instruction. The Program
Security Registers instruction is entered by driving /CS Low, followed by the instruction code (42H), three address
bytes and at least one data byte on SI. As soon as /CS is driven high, the self-timed Program Security Registers cycle
(whose duration is tPP) is initiated. While the Program Security Registers cycle is in progress, the Status Register
may be read to check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1 during the
self-timed Program Security Registers cycle, and is 0 when it is completed. At some unspecified time before the
cycle is completed, the Write Enable Latch bit is reset.

If the Security Registers Lock Bit (LB3/LB2/LB1) is set to 1, the Security Registers will be permanently locked.
Program Security Registers instruction will be ignored.

Address A23-A16 A15-A8 A7-A0


Security Registers 1 00H 01H Byte Address
Security Registers 2 00H 02H Byte Address
Security Registers 3 00H 03H Byte Address

Figure 26. Program Security Registers instruction Sequence Diagram

A 1.3
SPI NOR PN25F16
12.3 Program and Erase Instructions

12.3.1 Page Program (02H)


The Page Program instruction is for programming the memory. A Write Enable instruction must previously have
been executed to set the Write Enable Latch bit before sending the Page Program instruction.

See Figure 27, the Page Program instruction is entered by driving /CS Low, followed by the instruction code, three
address bytes and at least one data byte on SI. If the 8 least significant address bits (A7-A0) are not all zero, all
transmitted data that goes beyond the end of the current page are programmed from the start address of the same
page (from the address whose 8 least significant bits (A7-A0) are all zero). /CS must be driven low for the entire
duration of the sequence. The Page Program instruction sequence: /CS goes low sending Page Program instruction
3-byte address on SI at least 1 byte data on SI /CS goes high. The instruction sequence is shown in Figure16. If more
than 256 bytes are sent to the device, previously latched data are discarded and the last 256 data bytes are
guaranteed to be programmed correctly within the same page. If less than 256 data bytes are sent to device, they
are correctly programmed at the requested addresses without having any effects on the other bytes of the same
page. /CS must be driven high after the eighth bit of the last data byte has been latched in; otherwise the Page
Program instruction is not executed.

As soon as /CS is driven high, the self-timed Page Program cycle (whose duration is tPP) is initiated. While the Page
Program cycle is in progress, the Status Register may be read to check the value of the Write in Progress (WIP) bit.
The Write In Progress (WIP) bit is 1 during the self-timed Page Program cycle, and is 0 when it is completed. At some
unspecified time before the cycle is completed, the Write Enable Latch bit is reset.

A Page Program instruction applied to a page which is protected by the Block Protect (SEC, TB, BP2, BP1, BP0) is not
executed.

Figure 27. Page Program Sequence Diagram.

A 1.3
SPI NOR PN25F16
12.3.2 Sector Erase (20H)
The Sector Erase instruction is for erasing the all data of the chosen sector. A Write Enable instruction must
previously have been executed to set the Write Enable Latch bit. The Sector Erase instruction is entered by driving
/CS low, followed by the instruction code, and 3-address byte on SI. Any address inside the sector is a valid address
for the Sector Erase instruction. /CS must be driven low for the entire duration of the sequence.

See Figure 28, The Sector Erase instruction sequence: /CS goes low sending Sector Erase instruction 3-byte address
on SI /CS goes high. The instruction sequence is shown in Figure18.
/CS must be driven high after the eighth bit of the last address byte has been latched in; otherwise the Sector Erase
instruction is not executed. As soon as /CS is driven high, the self-timed Sector

Erase cycle (whose duration is tSE) is initiated. While the Sector Erase cycle is in progress, the Status Register may
be read to check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1 during the
self-timed Sector Erase cycle, and is 0 when it is completed. At some unspecified time before the cycle is completed,
the Write Enable Latch bit is reset. A Sector Erase instruction applied to a sector which is protected by the Block
Protect (SEC, TB, BP2, BP1, BP0) bit is not executed.

Figure 28. Sector Erase Sequence Diagram

A 1.3
SPI NOR PN25F16
12.3.3 32KB Block Erase (52H)
The 32KB Block Erase instruction is for erasing the all data of the chosen block. A Write Enable instruction must
previously have been executed to set the Write Enable Latch bit. The 32KB Block Erase instruction is entered by
driving /CS low, followed by the instruction code, and three address bytes on SI. Any address inside the block is a
valid address for the 32KB Block Erase instruction./CS must be driven low for the entire duration of the sequence.

See Figure 29, the 32KB Block Erase instruction sequence: /CS goes low sending 32KB Block Erase instruction 3-byte
address on SI /CS goes high. The instruction sequence is shown in Figure19. /CS must be driven high after the eighth
bit of the last address byte has been latched in; otherwise the 32KB Block Erase instruction is not executed. As soon
as /CS is driven high, the self-timed Block Erase cycle (whose duration is tBE) is initiated. While the Block Erase cycle
is in progress, the Status Register may be read to check the value of the Write In Progress (WIP) bit. The Write In
Progress (WIP) bit is 1 during the self-timed Block Erase cycle, and is 0 when it is completed. At some unspecified
time before the cycle is completed, the Write Enable Latch bit is reset. A 32KB Block Erase instruction applied to a
block which is protected by the Block Protect (SEC, TB, BP2, BP1, BP0) bits (see Table 6&7) is not executed.

Figure 29. 32KB Block Erase Sequence Diagram

A 1.3
SPI NOR PN25F16
12.3.4 64KB Block Erase (D8H)
The 64KB Block Erase instruction is for erasing the all data of the chosen block. A Write Enable instruction must
previously have been executed to set the Write Enable Latch bit. The 64KB Block Erase instruction is entered by
driving /CS low, followed by the instruction code, and three address bytes on SI. Any address inside the block is a
valid address for the 64KB Block Erase instruction./CS must be driven low for the entire duration of the sequence.

See Figure 30, the 64KB Block Erase instruction sequence: /CS goes low sending 64KB Block Erase instruction 3-byte
address on SI /CS goes high. The instruction sequence is shown in Figure20. /CS must be driven high after the eighth
bit of the last address byte has been latched in; otherwise the 64KB Block Erase instruction is not executed. As soon
as /CS is driven high, the self-timed Block Erase cycle (whose duration is tBE) is initiated. While the Block Erase cycle
is in progress, the Status Register may be read to check the value of the Write In Progress (WIP) bit. The Write In
Progress (WIP) bit is 1 during the self-timed Block Erase cycle, and is 0 when it is completed. At some unspecified
time before the cycle is completed, the Write Enable Latch bit is reset. A 64KB Block Erase instruction applied to a
block which is protected by the Block Protect (SEC, TB, BP2, BP1, BP0) bits (see Table 6&7) is not executed.

Figure 30. 64KB Block Erase Sequence Diagram

A 1.3
SPI NOR PN25F16
12.3.5 Chip Erase (60/C7H)

The Chip Erase instruction sets all memory within the device to the erased state of all 1s (FFh). Write Enable
instruction must be executed before the device will accept the Chip Erase Instruction (Status Register bit WEL must
equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code “C7h” or “60h”. The
Chip Erase instruction sequence is shown in Figure 31.

The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Chip Erase instruction
will not be executed. After /CS is driven high, the self-timed Chip Erase instruction will commence for a time
duration of tCE. While the Chip Erase cycle is in progress, the Read Status Register instruction may still be accessed
to check the status of the WIP bit.

The WIP bit is a 1 during the Chip Erase cycle and becomes a 0 when finished and the device is ready to accept other
Instructions again. After the Chip Erase cycle has finished the Write Enable Latch (WEL) bit in the Status Register is
cleared to 0. The Chip Erase instruction will not be executed if any page is protected by the Block Protect (CMP, SEC,
TB, BP2, BP1, and BP0) bits (see Table 6&7).

Figure 31. Chip Erase Sequence Diagram

A 1.3
SPI NOR PN25F16
12.3.6 Erase / Program Suspend (75H)
The Erase/Program Suspend instruction allows the system to interrupt a Sector or Block Erase operation, then read
from or program data to any other sector. The Erase/Program Suspend instruction also allows the system to
interrupt a Page Program operation and then read from any other page or erase any other sector or block. The
Erase/Program Suspend instruction sequence is shown in Figure 32.

The Write Status Registers instruction (01h) and Erase instructions (20h, D8h, C7h, 60h, 44h) are not allowed during
Erase Suspend. Erase Suspend is valid only during the Sector or Block erase operation. If written during the Chip
Erase operation, the Erase Suspend instruction is ignored. The Write Status Registers instruction (01h), and Program
instructions (02h, 42h) are not allowed during Program Suspend. Program Suspend is valid only during the Page
Program operation.

Figure 32. Erase/Program Suspend Command Sequence

A 1.3
SPI NOR PN25F16
12.3.7 Erase / Program Resume (7AH)
The Erase/Program Resume instruction “7Ah” must be written to resume the Sector or Block Erase operation or the
Page Program operation after an Erase/Program Suspend. The Resume instruction “7Ah” will be accepted by the
device only if the SUS bit in the Status Register equals to 1 and the WIP bit equals to 0.

After the Resume instruction is issued the SUS bit will be cleared from 1 to 0 immediately, the WIP bit will be set
from 0 to 1 within 200 ns and the Sector or Block will complete the erase operation or the page will complete the
program operation. If the SUS bit equals to 0 or the WIP bit equals to 1, the Resume instruction “7Ah” will be
ignored by the device. The Erase/Program Resume instruction sequence is shown in Figure 33.

Figure 33. Erase/Program Resume Command Sequence

A 1.3
SPI NOR PN25F16
13.Electrical Characteristics

13.1 Absolute Maximum Ratings


PARAMETERS SYMBOL CONDITIONS RANGE UNIT
Supply Voltage VCC –0.5 to 4 V
Voltage Applied to Any Pin VIO Relative to Ground –0.5 to 4 V
<20nS Transient
Transient Voltage on any Pin VIOT –2.0V to VCC+2.0V V
Relative to Ground
Storage Temperature TSTG –65 to +150 °C
Electrostatic Discharge Voltage VESD Human Body Model(1) –2000 to +2000 V
Notes:
1.JEDEC Std JESD22-A114A (C1=100pF, R1=1500 ohms, R2=500 ohms)

13.2 Operating Ranges


SPEC
PARAMETER SYMBOL CONDITIONS UNIT
MIN MAX

Supply Voltage VCC FR = 108MHz, fR = 50MHz 2.7 3.6 V

Temperature Commercial Industrial 0 +70


Operating TA °C
–40 +85

13.3 Data Retention and Endurance

Parameter Test Condition Min Units

150°C 10 Years
Minimum Pattern Data Retention Time 125°C 20 Years
Erase/Program Endurance -40 to 85°C 100K Cycles

13.4 Latch Up Characteristics


Parameter Min Max
Input Voltage Respect To VSS On I/O Pins -1.0V VCC+1.0V
VCC Current -100mA 100mA

A 1.3
SPI NOR PN25F16

13.5 Power-up Timing

Symbol Parameter Min Max Unit


tVSL VCC(min) To /CS Low 10 us

tPUW Time Delay From VCC(min) To Write Instruction 1 10 ms

VWI Write Inhibit Voltage VCC(min) 1 2.5 V

Figure 34. Power-up Timing and Voltage Levels

A 1.3
SPI NOR PN25F16
13.6 DC Electrical Characteristics
(T= -40℃~85℃, VCC=2.7~3.6V)
Test
Symbol Parameter Min. Typ Max. Unit.
Condition
ILI Input Leakage Current ±2 µA
Output Leakage
ILO ±2 µA
Current
/CS=VCC,
ICC1 Standby Current VIN=VCC 10 25 µA
or VSS
/CS=VCC,
Deep Power-Down VIN=VCC
ICC2 1 5 µA
Current or VSS
Current: Read
Single/Dual/Quad 1MHz 3/4/5 3.5/5/6 mA

Current: Read
Single/Dual/Quad 33MHz 5/10/13 7.5/11/14 mA
CLK=0.1VCC/
ICC3 Current:Read 0.9VCC(1)
ingle/Dual/Quad 50MHz 6.5/12/22 10/13/26 mA

Current: Read
Single/Dual/Quad 7/14/32 13/16/36 mA
108MHz
Operating
ICC4 Current(Page /CS=VCC 10 15 mA
rogram)
Operating
ICC5 Current(WRSR) /CS=VCC 5 mA
Operating 10
ICC6 /CS=VCC 20 mA
Current(Sector Erase)
Operating 10
ICC7 Current(Block Erase) /CS=VCC 20 mA
Operating Current 10
ICC8 /CS=VCC 20 mA
(Chip Erase)
VIL Input Low Voltage -0.5 0.2VCC V
VIH Input High Voltage 0.8VCC VCC+0.4 V
VOL Output Low Voltage IOL =100µA 0.4 V
VOH Output High Voltage IOH =-100µA VCC-0.2 V

Note:
(1)ICC3 is measured with ATE loading

A 1.3
SPI NOR PN25F16
13.7 AC Measurement Conditions

Symbol Parameter Min Tpy Max Unit Conditions

CL Load Capacitance 30 pF
TR, TF Input Rise And Fall time 5 ns
VIN Input Pause Voltage 0.2VCC to 0.8VCC V

IN Input Timing Reference Voltage 0.3VCC to 0.7VCC V


Output Timing Reference
OUT Voltage 0.5VCC V

Figure 35. AC Measurement I/O Waveform

13.8 AC Electrical Characteristics


Symbol Parameter Min. Typ. Max. Unit.

Clock frequency for all instructions, except, read


fc data(03H) DC. 108 MHz

fR Clock freq. Read Data instruction(03H) DC. 55 MHz


tCLH Serial Clock High Time 4 ns
tCLL Serial Clock Low Time 4 ns
(1)
tCLCH Serial Clock Rise Time (Slew Rate) 0.1 V/ns
(1)
tCHCL Serial Clock Fall Time (Slew Rate) 0.1 V/ns
tSLCH /CS Active Setup Time 5 ns
tCHSH /CS Active Hold Time 5 ns
tSHCH /CS Not Active Setup Time 5 ns
tCHSL /CS Not Active Hold Time 5 ns

A 1.3
SPI NOR PN25F16

Symbol

tSHSL /CS High Time(read/write) 2 ns


tSHQZ Output Disable Time 6 ns
tCLQX Output Hold Time 0 ns
tDVCH Data In Setup Time 2 ns
tCHDX Data In Hold Time 2 ns
tHLCH /Hold Low Setup Time (relative to Clock) 5 ns
tHHCH /Hold High Setup Time (relative to Clock) 5 ns
tCHHL /Hold High Hold Time (relative to Clock) 5 ns
tCHHH /Hold Low Hold Time (relative to Clock) 5 ns
tHLQZ /Hold Low To High-Z Output 6 ns
tHHQX /Hold Low To Low-Z Output 6 ns
tCLQV Clock Low To Output Valid 7 ns
tWHSL Write Protect Setup Time Before /CS Low 2 ns
tSHWL Write Protect Hold Time After /CS High 100 ns
tDP /CS High To Deep Power-Down Mode 0.1 µs
/CS High To Standby Mode Without Electronic
tRES1 3 µs
Signature Read
/CS High To tandby Mode With Electronic
tRES2 1.5 µs
Signature Read
tSUS /CS High To Next Instruction After Suspend 2 us
(2)
tW Write Status Register Cycle Time 10 15 ms
tPP Page Programming Time 0.7 2.4 ms
tSE Sector Erase Time 30 300 ms
tBE Block Erase Time(32K Bytes/64K Bytes) 0.2/0.3 1/1.2 s
tCE Chip Erase Time 15 35 s

Note:
a). Tested with clock frequency lower than 50 MHz.
b). tW can be up to 45 ms at -40℃ during the characterization of the current design. It will be improved in the
future design

A 1.3
SPI NOR PN25F16

Figure 36. Serial Input Timing

Figure 37. Output Timing

Figure 38. Hold Timing

A 1.3
SPI NOR PN25F16

14. Ordering Information


PN 25F 16 XX I U R
Company Prefix
PN = Paragon

Product Family
25F = 2.7~ 3.6V Serial Flash Memory with 4KB
Uniform-Sector, Standard / Dual SPI

Product Density
4
04 = 04M bit
08 = 08M bit
16 = 16M bit
32 = 32M bit

Product Package
SO = 8-pin SOP8(150mil)
SS = 8-pin SOP8(208mil)
DP = 8-pin DIP8(300mil)
TS = TSSOP8
`
Product Temperature
I = Industrial (-40℃ to +85℃)
C = Commercial (0℃ to +70℃)

Product Carrier
U = Tube
T = Tape and Reel
Green Code
R = Green/Reach Package
G = Green/Reach Package

A 1.3
SPI NOR PN25F16
15. Part Marking Scheme
15.1. SOP8 (150mil)/(208mil)

Paragon
PN25F16
YY WW XXX Product Density

The products code was molded (eg: Q0R)

Work week during which the products was molded (eg: week 12)
The last two digits of the year In which the products was seal / molded.

TSSOP8

PN25F16
Product Density
HSF ID CODE
R = RoHS Compliant
G = RoHS Compliant, Halogen-free, Antimony-free

Lot Number just with 0~9 A~Z


Assembly’s Code
Work week during which the products was molded (eg..week 12)
The last two digits of the year In which the products was seal / molded.

A 1.3
SPI NOR PN25F16
16.Packaging Information
SOP 8 (150mil)

Symbol MIN MAX


A 1.350 1.750
A1 0.050 0.250
b 0.330 0.510
c 0.150 0.250
D 4.700 5.150
E1 3.800 4.000
E 5.800 6.200
e 1.270(BSC)
L 0.400 1.270
θ 0° 8°

NOTE:
1. Dimensions are in Millimeters.

A 1.3
SPI NOR PN25F16

SOP 8 (208mil)

Symbol MIN MAX


A –– 2.100
A1 0.050 0.250
b 0.350 0.500
c 0.100 0.250
D 5.130 5.330
E1 5.180 5.380
E 7.700 8.100
e 1.270(BSC)
L 0.500 0.850
θ 0° 8°
NOTE:
1. Dimensions are in Millimeters.

A 1.3
SPI NOR PN25F16

TSSOP8

Symbol MIN MAX


D 2.830 3.100
E1 4.300 4.500
b 0.190 0.300
c 0.090 0.200
E 6.200 6.600
A 1.200
A1 0.050 0.150
e 0.650 (BSC)
L 0.450 0.750
H 0.250 (TYP)
θ 0° 8°
NOTE:
1. Dimensions are in Millimeters

A 1.3
SPI NOR PN25F16

DIP 8(300mil)

Symbol MIN MAX


A 3.710 4.31
A1 0.510
b 0.380 0.57
b2 1.524(BSC)
C 0.204 0.36
D 9.000 9.40
E1 6.200 6.60
E 7.320 7.92
e 2.540(BSC)
L 3.000 3.60
eB 8.400 9.000
NOTE:
1. Dimensions are in Millimeters.

A 1.3
SPI NOR PN25F16
17.Revision History
Publication
Version date Pages Revise Description

A1.0 oct. 2014 53 Initial Document Release.

A1.1 May.2015 56 Add SOP8 208mil package

A1.2 July.2015 57 Add TSSOP8 package.

A1.3 Sep.2015 58 Add DIP8 package && Update Green/Reach Package.

A 1.3

You might also like