Hydraulic Crawler Crane

Model : BMS1000

Max. Lifting Capacity : 100 t x 3.8 m

Max. Crane Boom Length : 62.6 m
1 BMS1000
BMS1000
CONTENTS

3 SPECIFICATIONS

5 GENERAL DIMENSIONS

6 BOOM AND JIB ARRANGEMENTS

7 WORKING RANGES

8 SUPPLEMENTAL DATA

9 LIFTING CAPACITIES

10 SUPPLEMENTAL DATA FOR CLAMSHELL

11 LIFTING CAPACITIES

12 SUPPLEMENTAL DATA FOR REDUCED WEIGHTS

13 LIFTING CAPACITIES

14 SUPPLEMENTAL DATA FOR BARGE

15 LIFTING CAPACITIES

16 TRANSPORTATION PLAN

17 PARTS AND ATTACHMENTS

BMS1000 2
SPECIFICATIONS
Power Plant Load Hoisting System

Model: HINO P11C-VH Front and rear drums for load hoist powered by a hydraulic
Type: 4 cycle, water-cooled, vertical in-line 6, direct injection, variable plunger motors, driven through planetary reducers.
turbo-charger, intercooler. Positive & Negative Brake: Forced-circulation oil-cooled wet-
Exhaust level is equivalent with NRMM (Europe) Stage III A / US type multi-disc brake, each using positive and negative actuation.
EPA Tier3. The drums are manually locked by the control cable. Both
Displacement: 10.52 L positive and negative brake systems are available in lever neutral
Rated power: 271 kW / 1,850 min-1 position.
Max. Torque: 1,470 N·m / 1,400 min-1 Drum Lock: External ratchet for locking drum
Cooling System: Water-cooled Drums:
Starter: 24 V- 6 kW Front Drums: 616 mm P.C.D x 620 mm wide drum, grooved for
Radiator: Corrugated type core, thermostatically controlled 28 mm wire rope. Rope capacity is 200 m working length and
Air cleaner: Dry type with replaceable paper element 284 m storage length.
Throttle: Twist grip type hand throttle, electrically actuated Rear Drum: 616 mm P.C.D x 620 mm grooved for 28 mm
Fuel filter: Replaceable paper element wire rope. Rope capacity is 130 m working length and 284 m
Batteries: Two 12 V x 136 Ah/5HR capacity batteries, series storage length.
connected Diameter of wire rope
Fuel tank capacity: 400 L Main winch: 28 mm x 200 m
Aux. winch: 28 mm x 130 m
Third winch: 26 mm x 190 m
Hydraulic System Line Speed*:
Hoisting/lowering: 110 to 3 m/min
Main pumps: 3 variable displacement piston pumps Line Pull:
Control: Full-flow hydraulic control system for infinitely variable Max. Line Pull* : 252 kN {25.7 tf}
pressure to all winches, propel and swing. Controls respond (Referential Performance)
instantly to the touch, delivering smooth function operation. Rated Line Pull: 132 kN {13.5 tf}
Cooling: Oil-to-air heat exchanger (plate-fin type) *Single line on first drum layer
Filtration: Full-flow and bypass type with replaceable element
Max. relief valve pressure:
Load hoist, boom hoist and propel system: 31.9 MPa Swing System
Swing system: 27.5 MPa
Control system: 5.4 MPa Swing unit is powered by hydraulic motor driving spur gears
Oil Quantity (at the reference level): 375 L through planetary reducers, the swing system provides 360°
rotation.
Swing parking brakes: A spring-set, hydraulically released
Boom Hoisting System multiple-disc brake is mounted on swing motor.
Swing circle: Single-row ball bearing with an integral internally
Powered by a hydraulic motor through a planetary reducer. cut swing gear.
Brake: A spring-set, hydraulically released multiple-disc brake Swing lock: Manually, four position lock for transportation
is mounted on the boom hoist motor and operated through a Swing Speed: 3.2 min-1
counter-balance valve.
Drum Lock: External ratchet for locking drum
Drum: Single drum, grooved for 20 mm dia. wire rope Upper Structure
Line Speed: Single line on first drum layer
Hoisting/Lowering: 50 to 3 m/min Torsion-free precision machined upper frame. All components
Boom hoisting/lowering: 20 mm x 140 m are located clearly and service friendly. Engine will with low noise
Boom guy line: 34 mm level.
Boom backstops: Required for all boom length Counterweight: 37.1 ton

3 BMS1000
 Cab & Control Weight

Totally enclosed, full vision cab with safety glass, fully adjustable, Including upper and lower machine, 37.1 ton counterweight
high backed seat with a headrest and armrests, and intermittent and 14.6 ton carbody weight, basic boom hook, and other
wiper and window washer (skylight and front window). accessories.
Cab fittings: Weight: 107.0 ton
Air conditioner, convenient compartment (for tool), cup holder, Ground pressure: 109 kPa
cigarette lighter, sun visor, roof blind, tinted glass, floor mat,
footrest, and shoe tray
Attachment
,er
Lower Structure Boom & Jib:
Welded lattice construction using tubular, high-tensile steel
Steel-welded carbody with axles. Crawler assemblies can be chords with pin connection between sections.
hydraulically extended for wide-track operation or retracted for
transportation. Crawler belt tension is maintained by hydraulic Boom length
jack force on the track-adjusting bearing block. Min. Length Max. Length
Carbody weight: 14.6 ton Crane Boom 13.8 m 62.6 m
Crawler drive: Independent hydraulic propel drive is built into
each crawler side frame. Each drive consists of a hydraulic
motor propelling a driving tumbler through a planetary gear box.
Hydraulic motor and gear box are built into the crawler side
frame within the shoe width.
Crawler brakes: Spring-set, hydraulically released parking
brakes are built into each propel drive.
Steering mechanism: A hydraulic propel system provides
both skid steering (driving one track only) and counter-rotating
steering (driving each track in opposite directions).
Track rollers : Sealed track rollers for maintenance -free
operation.
Shoe (flat): 900 mm wide each crawler
Max. gradeability: 30%

Main Specifications (Model: BMS1000)

Crane Boom Hydraulic System
Max. Lifting Capacity 100 t x 3.8 m Main Pumps 3 variable displacement
Max. Length 62.6 m Max. Pressure 31.9 MPa {325 kgf/cm2}
Main & Aux. Winch Oil Quantity (at the reference level) 375 L
Max. Line Speed (1st layer) 110 m/min Self-Removal Device
Rated Line Pull (Single line) 132 kN {13.5 tf} NA
Wire Rope Diameter 28 mm Weight
Wire Rope Length 200 m (Main), 130 m (Aux.) Operating Weight 107 t *1
Brake Type (Free fall) Wet-type multiple disc brake (Standard) Ground Pressure 109 kPa
Working Speed Counterweight 37,140 kg
Swing Speed 3.2 min-1{rpm} Transport Weight 31,000 kg *2
Travel Speed 1.4/1.0 km/h Units are SI units. { } indicates conventional units.
Power Plant Line speeds in table are for light loads. Line speed varies with load.
*1 Including upper and lower machine, 37.1 ton counterweight, 14.6 ton
Model HINO P11C-VH
carbody weight, basic boom, hook, and other accessories.
Engine Output 271 kW / 1,850 min-1 *2 Base machine with boom base, gantry, and wire ropes (front/rear/third/
Fuel Tank 400 L boom hoist)

BMS1000 4
GENERAL DIMENSIONS
(Unit: mm)

4,200

900
0
,40
R4 .8
m
13

5,720
3,360 1,100

2,990
1,495
940
6,950

2,590
3,460

3,555

450
2,200
1,275

5,345 3,500
(CRAWLER RETRACTED)
6,315
4,900
(CRAWLER EXTENDED)

This catalog may contain photographs of machines with specifications, attachments and optional equipment.

Limit of Hook Lifting

L L’
Hook L
100 t hook 5.4 m
50 t hook 5.0 m Hook L’
35 t hook 5.0 m Ball hook 4.2 m

5 BMS1000
BOOM AND JIB ARRANGEMENTS
Crane Boom Arrangements
Boom Boom
Boom arrangement Boom arrangement
length m (ft) length m (ft)

13.8 (45) 6.2

B T
7.6
B 3.0 6.1 9.1 9.1 T
41.2 (135)
B 9.1 9.1 9.1 T

16.9 (55) B 3.0 T

B 3.0 3.0 6.1 9.1 9.1 T

44.3 (145) B 3.0 9.1 9.1 9.1 T

B 6.1 6.1 9.1 9.1 T

B 3.0 3.0 T
19.9 (65)
B 6.1 T

B 3.0 3.0 9.1 9.1 9.1 T

47.3 (155) B 3.0 6.1 6.1 9.1 9.1 T

B 3.0 6.1 T B 6.1 9.1 9.1 9.1 T

23.0 (75)
B 9.1 T

B 3.0 6.1 9.1 9.1 9.1 T

50.4 (165)
B 3.0 3.0 6.1 T
B 9.1 9.1 9.1 9.1 T
26.0 (85) B 3.0 9.1 T

B 6.1 6.1 T

B 3.0 3.0 6.1 9.1 9.1 9.1 T

53.4 (175) B 3.0 9.1 9.1 9.1 9.1 T

B 3.0 3.0 9.1 T

B 6.1 6.1 9.1 9.1 9.1 T
29.1 (95) B 3.0 6.1 6.1 T

B 6.1 9.1 T

B 3.0 3.0 9.1 9.1 9.1 9.1 T

56.5 (185) B 3.0 6.1 6.1 9.1 9.1 9.1 T

B 3.0 6.1 9.1 T

32.1 (105) B 6.1 9.1 9.1 9.1 9.1 T
B 9.1 9.1 T

59.5 (195) B 3.0 6.1 9.1 9.1 9.1 9.1 T

B 3.0 3.0 6.1 9.1 T

35.2 (115) B 6.1 6.1 9.1 T

B 3.0 9.1 9.1 T

62.6 (205) B 3.0 3.0 6.1 9.1 9.1 9.1 9.1 T

B 3.0 3.0 9.1 9.1 T

Symbol Boom Length Remarks
38.2 (125) B 3.0 6.1 6.1 9.1 T
B 6.2 m Boom Base
B 6.1 9.1 9.1 T
T 7.6 m Boom Tip
3.0 3.0 m Insert Boom
6.1 6.1 m Insert Boom
9.1 9.1 m Insert Boom
mark shows the standard boom arrangement which
enables each boom length of less than that boom
length to be configured.

BMS1000 6
WORKING RANGES
Crane Boom

80° 75° 70° 65° 60° 55°

66
62.6 m Boom
64
59.5 m Boom 62
60
56.5 m Boom
50°
58
53.4 m Boom 56
54
50.4 m Boom
52
47.3 m Boom 50
45°
48
44.3 m Boom
46
41.2 m Boom 44

40° 42
38.2 m Boom
40

Height above ground (m)

35.2 m Boom 38
36
35°
32.1 m Boom
34

29.1 m Boom 32
30
26.0 m Boom
28

23.0 m Boom 30° 26

24
19.9 m Boom
22

16.9 m Boom 20
18
13.8 m Boom
16
14

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46

Radius from center of rotation (m)

2.2m

Center
of rotation

1.1m

7 BMS1000
SUPPLEMENTAL DATA
• Ratings according to japanese construction codes for mobile (Crane boom lifting)
cranes. • The total load that can be lifted is the value for weight of hook
• Operating radius is the horizontal distance from centerline of block, slings, and all other load handling accessories deducted
rotation to a vertical line through the center of gravity of the from main boom ratings shown.
load.
• Deduct weight of hook block(s) , slings and all other load <Reference Information>
handling accessories from main boom ratings shown. Main hoist loads
• Ratings shown are based on freely suspended loads and make No. of Parts of Line 1 2 3 4 5
no allowance for such factors as wind effect on lifted load, Maximum Loads (kN) 132 245 368 490 613
ground conditions, out-of-level, operating speeds or any other Maximum Loads (t) 13.5 25.0 37.5 50.0 62.5
condition that could be detrimental to the safe operation of
this equipment. The operator, therefore, has the responsibility No. of Parts of Line 6 7 8
to judge the existing conditions and reduce lifted loads and Maximum Loads (kN) 735 858 981
operating speeds accordingly. Maximum Loads (t) 75.0 87.5 100.0
• Ratings are for operation on a firm and level surface, up to 1%
gradient. Auxiliary hoist loads
• At radii and boom lengths where no ratings are shown on No. of Parts of Line 1
chart, operation is not intended nor approved. Maximum Loads (kN) 132
• Boom inserts and guy lines must be arranged as shown in the Maximum Loads (t) 13.5
"operator's manual".
• Boom hoist reeving is 10 part line. Third hoist loads
• Gantry must be in raised position for all conditions. No. of Parts of Line 2 3 4 5 6
• Boom backstops are required for all boom lengths. Maximum Loads (kN) 216 324 431 539 647
• The boom should be erected over the front of the crawlers, not Maximum Loads (t) 22.0 33.0 44.0 55.0 66.0
laterally. * One part of line on hook is not allowed to use.
• Ratings inside of boxes are limited by strength of
materials. Weight of hook block
• The minimum rated load is 1.5 (ton). Hook Block 100 t 50 t 35 t Ball Hook
• Crawler frames must be fully extended for all crane operations. Weight (t) 1.73 0.85 0.70 0.45
• When erecting and lowering the boom length of 59.5 m and
62.6 m, the blocks for erection must be placed at the end of Operation of this equipment in excess of rated loads
the crawlers. or disregard of instruction voids the warranty.

BMS1000 8
LIFTING CAPACITIES
Counterweight: 37.1 t
Crane Boom Lifting Capacities Carbody Weight: 14.6 t
Unit: metric ton
Boom Boom
length length
Working (m) 13.8 16.9 19.9 23.0 26.0 29.1 32.1 35.2 38.2 41.2 (m) Working
radius (m) radius (m)

3.8 100.0 3.8

4.3 4.3m/90.0 4.3m/87.5 4.8m/78.0 4.3
5.0 74.0 74.0 73.5 5.4m/70.0 5.9m/61.5 5.0
6.0 61.5 61.5 61.5 61.5 61.0 6.4m/56.8 6.0
7.0 51.3 51.1 51.0 50.9 50.8 50.8 50.0 7.5m/45.0 7.0
8.0 42.4 42.2 42.1 42.0 41.9 41.8 41.8 41.7 41.3 8.5m/37.5 8.0
9.0 36.0 35.9 35.7 35.6 35.5 35.5 35.4 35.3 35.2 35.1 9.0
10.0 31.3 31.1 31.0 30.9 30.8 30.7 30.6 30.5 30.4 30.3 10.0
12.0 22.0 24.5 24.3 24.2 24.1 24.0 24.0 23.8 23.7 23.6 12.0
14.0 13.2m/18.7 20.1 19.9 19.8 19.7 19.6 19.5 19.4 19.2 19.2 14.0
16.0 15.8m/14.9 16.8 16.7 16.5 16.5 16.4 16.2 16.1 16.0 16.0
18.0 13.6 14.3 14.2 14.1 14.0 13.8 13.7 13.7 18.0
20.0 18.5m/12.5 12.5 12.4 12.3 12.2 12.0 11.9 11.8 20.0
22.0 21.1m/11.1 10.9 10.8 10.7 10.5 10.4 10.3 22.0
24.0 23.8m/9.8 9.6 9.5 9.3 9.2 9.1 24.0
26.0 8.7 8.5 8.3 8.2 8.1 26.0
28.0 26.4m/8.2 7.7 7.5 7.4 7.3 28.0
30.0 29.0m/7.3 6.8 6.7 6.6 30.0
32.0 31.7m/6.3 6.1 6.0 32.0
34.0 5.5 5.4 34.0
36.0 34.3m/5.5 4.9 36.0
38.0 37.0m/4.7 38.0
Reeves 8 7 7 6 5 5 4 4 4 3 Reeves

Boom Boom
length length
Working (m) 44.3 47.3 50.4 53.4 56.5 59.5 62.6 (m) Working
radius (m) radius (m)

9.0 9.1m/34.6 9.6m/31.8 9.0

10.0 30.2 30.1 10.1m/25.0 10.7m/25.0 11.2m/21.6 11.7m/20.1 10.0
12.0 23.5 23.4 23.3 23.2 19.5 19.4 12.2m/18.0 12.0
14.0 19.0 18.9 18.9 18.7 18.6 18.0 15.4 14.0
16.0 15.9 15.7 15.7 15.5 15.4 15.0 14.5 16.0
18.0 13.5 13.4 13.3 13.2 13.0 12.9 12.7 18.0
20.0 11.6 11.5 11.5 11.3 11.2 11.0 10.9 20.0
22.0 10.2 10.0 10.0 9.8 9.7 9.6 9.4 22.0
24.0 9.0 8.8 8.8 8.6 8.5 8.4 8.2 24.0
26.0 8.0 7.8 7.8 7.6 7.5 7.3 7.2 26.0
28.0 7.1 7.0 6.9 6.8 6.6 6.5 6.3 28.0
30.0 6.4 6.3 6.2 6.0 5.9 5.8 5.6 30.0
32.0 5.8 5.6 5.6 5.4 5.3 5.1 5.0 32.0
34.0 5.2 5.1 5.0 4.8 4.7 4.6 4.4 34.0
36.0 4.8 4.6 4.5 4.4 4.2 4.1 3.9 36.0
38.0 4.3 4.2 4.1 3.9 3.8 3.7 3.5 38.0
40.0 39.6m/4.0 3.8 3.7 3.6 3.4 3.3 3.0 40.0
42.0 3.5 3.4 3.2 3.0 2.9 2.6 42.0
44.0 42.2m/3.5 3.1 2.9 2.7 2.5 44.0
46.0 44.9m/3.0 2.5 46.0
Reeves 3 3 2 2 2 2 2 Reeves

Note:
Ratings according to Japanese Construction Codes for Mobile Cranes and Japanese Safety Ordinance on Cranes, etc.
Ratings shown in are determined by the strength of the boom or other structural components.
Refer to notes P.8.
Lifting capacities may vary depending on hook used or with/without auxiliary sheave.
Please refer rated chart in operator’s cabin.

9 BMS1000
SUPPLEMENTAL DATA FOR CLAMSHELL RATING CHART
• Operating radius is the horizontal distance from centerline of (Clamshell bucket lifting)
rotation to a vertical line through the center of gravity of the • The total load that can be lifted is the value for weight of
load. bucket, slings, and all other load handling accessories
• Deduct weight of bucket, slings and all other load handling deducted from main boom ratings shown.
accessories from main boom ratings shown. • The weight of bucket and materials must not exceed rated
• Ratings shown are based on freely suspended loads and make load.
no allowance for such factors as wind effect on lifted load, • Optimum bucket should be required according to material.
ground conditions, out-of-level, operating speeds or any other • Bucket capacity (m3) x specified gravity of material (ton/m3) +
condition that could be detrimental to the safe operation of bucket weight (ton) = rated load.
this equipment. The operator, therefore, has the responsibility • Bucket weight must also be decreased according to operating
to judge the existing conditions and reduce lifted loads and cycle and bucket lowering height.
operating speeds accordingly. • Rated loads are determined by stability and boom strength.
• Rated loads do not exceed 66% of minimum tipping loads. During simultaneous operations of boom and swing, rapid
• Ratings are for operation on a firm and level surface, up to 1% acceleration or deceleration must be avoided.
gradient. • Do not attempt to cast the bucket while swinging or diagonal
• At radii and boom lengths where no ratings are shown on draw-cutting.
chart, operation is not intended nor approved.
• Boom inserts and guy lines must be arranged as shown in the <Reference Information>
"operator's manual". Main hoist loads
• Boom hoist reeving is 10 part line. No. of Parts of Line 1
• Gantry must be in raised position for all conditions. Maximum Loads (kN) 122
• Boom backstops are required for all boom lengths. Maximum Loads (t) 12.5
• The boom should be erected over the front of the crawlers, not
laterally. Assembling the counterweight
• Crawler frames must be fully extended for all crane operations. (STD)
37.1 ton counterweight
14.6 ton carbody weight
No.6 No.7
No.4 No.5
No.3
No.2
No.1
Counterweights

Carbody weights

Operation of this equipment in excess of rated loads

or disregard of instruction voids the warranty.

BMS1000 10
LIFTING CAPACITIES
Clamshell Rating Charts Counterweight: 37.1 t
Carbody Weight: 14.6 t
Crane Boom Capacities Unit: metric ton
Boom Boom
length length
Load (m) 13.8 16.9 19.9 23.0 26.0 (m) Load
radius (m) radius (m)

6.0 12.5 6.0

7.0 12.5 12.5 7.0
8.0 12.5 12.5 12.5 8.0
9.0 12.5 12.5 12.5 11.4 9.0
10.0 12.5 12.5 12.5 11.4 9.4 10.0
12.0 12.5 12.5 12.5 11.4 9.4 12.0
14.0 12.2 12.2 11.4 9.3 14.0
16.0 10.7 10.7 9.1 16.0
18.0 17.0m/9.9 9.5 8.6 18.0
20.0 8.2 8.1 20.0
22.0 7.3 22.0
24.0 24.0
26.0 26.0
28.0 28.0
30.0 30.0
32.0 32.0
Reeves 1 1 1 1 1 Reeves

Note:
Please refer rated chart in operator’s cabin.

11 BMS1000
SUPPLEMENTAL DATA FOR REDUCED WEIGHTS RATING CHART
• Ratings according to japanese construction codes for mobile (Crane boom lifting)
cranes. The total load that can be lifted is the value for weight of hook
• Operating radius is the horizontal distance from centerline of block, slings, and all other load handling accessories deducted
rotation to a vertical line through the center of gravity of the from main boom ratings shown.
load.
• Deduct weight of hook block(s) , slings and all other load <Reference Information>
handling accessories from main boom ratings shown. Main hoist loads
• Ratings shown are based on freely suspended loads and make No. of Parts of Line 1 2 3 4 5
no allowance for such factors as wind effect on lifted load, Maximum Loads (kN) 132 245 368 490 613
ground conditions, out-of-level, operating speeds or any other Maximum Loads (t) 13.5 25.0 37.5 50.0 62.5
condition that could be detrimental to the safe operation of
No. of Parts of Line 6 7 8
this equipment. The operator, therefore, has the responsibility
Maximum Loads (kN) 735 858 981
to judge the existing conditions and reduce lifted loads and
Maximum Loads (t) 75.0 87.5 100.0
operating speeds accordingly.
• Ratings are for operation on a firm and level surface, up to 1% Auxiliary hoist loads
gradient. No. of Parts of Line 1
• At radii and boom lengths where no ratings are shown on Maximum Loads (kN) 132
chart, operation is not intended nor approved. Maximum Loads (t) 13.5
• Boom inserts and guy lines must be arranged as shown in the
"operator's manual". Weight of hook block
• Boom hoist reeving is 10 part line. Hook Block 100 t 50 t 35 t Ball Hook
• Gantry must be in raised position for all conditions. Weight (t) 1.73 0.85 0.70 0.45
• Boom backstops are required for all boom lengths.
• The boom should be erected over the front of the crawlers, not
laterally. Assembling the counterweight
• Ratings inside of boxes are limited by strength of 26.8 ton counterweight
materials. without carbody weight
• The minimum rated load is 1.5 (ton).
• Crawler frames must be fully extended for all crane operations.
No.3
No.2
No.1
Counterweights

Carbody weights

The lifting capacity does not change due to the type of

counterweights.

Operation of this equipment in excess of rated loads

or disregard of instruction voids the warranty.

BMS1000 12
LIFTING CAPACITIES
Reduced Weights Rating Charts Counterweight: 26.8 t
Without Carbody Weight
Crane Boom Lifting Capacities Unit: metric ton
Boom Boom
length length
Load (m) 13.8 16.9 19.9 23.0 26.0 29.1 32.1 35.2 38.2 41.2 44.3 47.3 50.4 53.4 (m) Load
radius (m) radius (m)

3.8 3.8m/90.0 3.8

4.3 80.0 4.3m/80.0 4.8m/66.7 4.3
5.0 62.3 62.3 62.2 5.4m/54.4 5.9m/46.9 5.0
6.0 46.0 46.0 45.8 45.8 45.8 6.4m/41.1 6.0
7.0 36.3 36.2 36.1 36.0 35.9 35.8 7.0m/35.8 7.5m/32.1 7.0
8.0 29.8 29.7 29.6 29.5 29.4 29.3 29.3 29.2 8.0m/29.0 8.5m/26.5 8.0
9.0 25.3 25.2 25.0 24.9 24.8 24.7 24.7 24.5 24.4 24.4 9.1m/23.8 9.6m/21.9 9.0
10.0 21.9 21.7 21.6 21.5 21.4 21.3 21.2 21.1 21.0 21.0 20.8 20.7 10.1m/20.3 10.7m/18.5 10.0
12.0 17.1 17.0 16.8 16.7 16.6 16.5 16.4 16.3 16.2 16.1 16.0 15.9 15.9 15.7 12.0
14.0 13.2m/15.2 13.9 13.7 13.6 13.4 13.3 13.3 13.1 13.0 12.9 12.8 12.7 12.6 12.5 14.0
16.0 15.8m/11.8 11.4 11.3 11.2 11.1 11.0 10.8 10.7 10.7 10.5 10.4 10.4 10.2 16.0
18.0 9.8 9.7 9.5 9.4 9.3 9.1 9.0 9.0 8.8 8.7 8.7 8.5 18.0
20.0 18.5m/9.5 8.4 8.2 8.1 8.0 7.8 7.7 7.7 7.5 7.4 7.3 7.2 20.0
22.0 21.1m/7.8 7.2 7.1 7.0 6.8 6.7 6.6 6.4 6.3 6.3 6.1 22.0
24.0 23.8m/6.4 6.2 6.1 5.9 5.8 5.7 5.6 5.4 5.4 5.2 24.0
26.0 5.5 5.4 5.2 5.1 5.0 4.9 4.7 4.7 4.5 26.0
28.0 26.4m/5.4 4.9 4.7 4.5 4.4 4.3 4.1 4.1 3.9 28.0
30.0 29.0m/4.6 4.2 4.0 3.9 3.7 3.6 3.6 3.4 30.0
32.0 31.7m/3.8 3.6 3.5 3.3 3.2 3.1 3.0 32.0
34.0 3.2 3.1 2.9 2.8 2.7 2.6 34.0
36.0 34.3m/3.2 2.8 2.6 2.5 2.4 2.2 36.0
38.0 37.0m/2.6 2.3 2.1 2.0 38.0m/1.8 38.0
40.0 39.6m/2.1 1.8 40.0m/1.7 40.0
42.0 1.5 42.0
44.0 42.2m/1.5 44.0
Reeves 8 7 6 5 4 4 3 3 3 3 2 2 2 2 Reeves

Note:
Ratings according to Japanese Construction Codes for Mobile Cranes and Japanese Safety Ordinance on Cranes, etc.
Ratings shown in are determined by the strength of the boom or other structural components.
Lifting capacities may vary depending on hook used or with/without auxiliary sheave.
Please refer rated chart in operator’s cabin.

13 BMS1000
SUPPLEMENTAL DATA FOR BARGE RATING CHART
• Operating radius is the horizontal distance from centerline of • The boom should be erected over the front of the crawlers, not
rotation to a vertical line through the center of gravity of the laterally.
load. • Ratings inside of boxes are limited by strength of materials.
• Deduct weight of hook block (s), slings and all other load • The minimum rated load is 1.5 (ton).
handling accessories from main boom ratings shown. • Crawler frames must be fully extended for all crane operations.
• Condition of barge stability this rating chart were determined • The machinery should be fastened to the deck of the barge to
under the condition below. The stability of barge shall meet prevent tip over and sliding.
below condition. During operation the machinery static • Towing area
inclination against horizontal level. Towing area shall be within coastal area and quiet wave
(A) Both sides (right & left) of machine condition. Offshore and open sea is not considered for this
Maximum inclination shall be within 1.5 Degrees machinery. Depend on the height of wave, counterweight shall
(B) Front & backward of machine be reduced during towing.
Maximum inclination shall be within 3.0 Degrees
(Crane boom)
Direction of Right and Left • The total load that can be lifted is the value for weight of hook
for Machinery
block, slings, and all other load handling accessories deducted
from main boom ratings shown.

<Reference Information>
Main hoist loads
No. of Parts of Line 1 2 3 4 5
Maximum Loads (kN) 132 245 368 490 588
Maximum Loads (t) 13.5 25.0 37.5 50.0 60.0
Direction of Front and Rear
for Machinery
Auxiliary hoist loads
No. of Parts of Line 1
(A) (B)
1.5° Maximum Loads (kN) 132
Maximum Loads (t) 13.5

Weight of hook block

Hook Block 100 t 50 t 35 t Ball Hook

1.5° 3° Weight (t) 1.73 0.85 0.70 0.45

Operation of this equipment in excess of rated loads

• Working area shall be inshore and smooth water. or disregard of instruction voids the warranty.
• Applicable regulations for structure japanese construction
codes for mobil crane
Regulation of class of shipping (abs, lloyd, bv, nk, etc) are
not adapted.
• At radii and boom lengths where no ratings are shown on
chart, operation is not intended nor approved.
• Boom inserts and guy lines must be arranged as shown in the
"operator's manual".
• Boom hoist reeving is 10 part line.
• Gantry must be in raised position for all conditions.
• Boom backstops are required for all boom lengths.

BMS1000 14
LIFTING CAPACITIES
Counterweight: 37.1 t
Barge Rating Chart Carbody Weight: 14.6 t
Crawler Fully Extended
Crane Boom Lifting Capacities Unit: metric tons
Boom Boom
length length
Load (m) 13.8 16.9 19.9 23.0 26.0 29.1 32.1 35.2 38.2 (m) Load
radius (m) radius (m)

4.0 4.7m/60.0 4.0

5.0 55.0 5.2m/49.4 5.9m/43.5 5.0
6.0 43.1 42.9 42.8 6.6m/38.4 6.0
7.0 36.7 36.4 36.2 36.1 7.3m/34.3 7.9m/31.3 7.0
8.0 31.8 31.5 31.4 31.2 31.0 30.9 8.6m/28.2 8.0
9.0 27.9 27.7 27.6 27.5 27.3 27.1 26.9 9.3m/25.7 9.0
10.0 23.2 24.6 24.5 24.4 24.2 24.0 23.8 23.7 10.0m/23.6 10.0
12.0 16.5 18.2 19.6 19.7 19.6 19.5 19.4 19.1 19.0 12.0
14.0 13.2m/13.2 13.9 15.1 16.1 15.9 15.8 15.8 15.6 15.5 14.0
16.0 15.8m/11.1 12.0 12.9 13.3 13.2 13.1 13.0 12.8 16.0
18.0 9.7 10.5 11.1 11.3 11.2 11.0 10.9 18.0
20.0 18.5m/9.1 8.6 9.2 9.7 9.7 9.5 9.4 20.0
22.0 21.1m/7.8 7.7 8.2 8.5 8.3 8.2 22.0
24.0 23.8m/6.6 6.9 7.3 7.3 7.2 24.0
26.0 5.9 6.3 6.5 6.4 26.0
28.0 26.4m/5.7 5.4 5.6 5.7 28.0
30.0 29.0m/5.0 4.8 5.1 30.0
32.0 31.7m/4.3 4.5 32.0
34.0 3.9 34.0
36.0 34.3m/3.8 36.0
Reeves 5 4 4 4 3 3 3 3 2 Reeves

Note:
Ratings according to japanese construction codes for mobile cranes and japanese safety ordinance on cranes, etc.
Ratings shown in are determined by the strength of the boom or other structural components.
Lifting capacities may vary depending on hook used or with/without auxiliary sheave.
Please refer rated chart in operator’s cabin.

15 BMS1000
TRANSPORTATION PLAN
Name Dimension (mm) Weight (kg)

Base Machine
13,240 2,990*1
• Boom base
• Gantry
• Crawler

3,555
3,460
• Crane backstop 51,600
• Dummy weight
(for third winch)
• Wire rope 3,500
(Front / rear / boom hoist)

Base Machine 6,835 2,990*1

• Crawler
• Dummy weight
(for third winch)
3,555

3,555
47,600
• Wire rope
(Front / rear)
3,500

Base Machine
• Boom base 13,240 2,990*1
• Gantry
• Dummy weight
(for third winch)
3,210
3,115

31,000
• Wire rope
(Front / rear / boom hoist)
• Crane backstop 3,500 2,990
• Without crawler
• Without side steps

Base Machine 6,185 2,990*1

• Dummy weight
(for third winch)
• Wire rope
3,105
3,105

25,600
(Front / rear)
• Without crawler
• Without translifter 3,500 2,990
• Without side steps
1,145

6,315 1,070

Crawler 10,300

*1 With the side step on cabin side : 3,170

With the side steps on the both sides : 3,340

BMS1000 16
PARTS AND ATTACHMENTS
Base Machine Crawler
Boom base, Gantry, Crawler, Crane backstop, Third winch Weight: 10,300 kg
Wire rope (Front/rear/third/boom hoist),
Weight: 51,600 kg Width: 3,500 mm
6,315 1,070
13,240

1,145
3,460

2,990
3,555

3,500

Counterweight No.1 Counterweight No.2 Counterweight No.3

Weight: 9,920 kg Weight: 8,940 kg Weight: 7,960 kg

975
975

975

645
1,045

4,200 4,200
645

4,200

Counterweight No.4 (L) Counterweight No.5 (R) Counterweight No.6 (L)

Weight: 2,350 kg Weight: 3,740 kg Weight: 1,740 kg

1,280 680 680 1,645 1,280 495

975

975
950

Counterweight No.7 (R) Carbody Weight

Weight: 2,490 kg Weight: 7,250 kg

495 1,645
1,225
950

1,555
840

17 BMS1000
 Gantry Insert Boom
Weight: 1,410 kg
L 1,670

1,220

1,690
4,995
L (mm) Weight (kg)*

845
3.0m 3,160 400
6.1m 6,210 670
9.1m 9,260 940
*Without pins

Boom Tip Boom Base

Weight: 1,720 kg (with boom guy cables) Weight: 1,580 kg

1,680 8,320 6,370 1,730

1,700
1,690

2,060
Crane Backstop Upper Spreader
Weight: 130 kg Weight: 300 kg
1,780 305
4,900
ĭ

Lower Spreader Ball Hook 35 t Hook

Weight: 200 kg Weight: 450 kg Weight: 700 kg
ĭ
400 700
710

1,135
1,205

1,575

905 253

50 t Hook 100 t Hook Single sheave auxiliary sheave

Weight: 850 kg Weight: 1,730 kg Weight: 280 kg
Width: 315 mm
435 700 540 700
1,210
735
1,215

1,430
1,705

2,140

2 sheaves auxiliary sheave

Weight: 550 kg
Width: 780 mm

1,480
925

BMS1000 18
Note: This catalog may contain photographs of machines with specifications, attachments and optional equipment not certified for operation in your
country. Please consult KOBELCO for those items you may require. Due to our policy of continual product improvements all designs and
specifications are subject to change without advance notice.
Copyright by KOBELCO CONSTRUCTION MACHINERY CO., LTD. No part of this catalog may be reproduced in any manner without notice.

Inquiries To :
5-15, Kitashinagawa 5-chome, Shinagawa-ku,Tokyo 141-8626 JAPAN
Tel: +81-3-5789-2121 Fax: +81-3-5789-3372
URL: https://www.kobelcocm-global.com

KOBELCO is the corporate mark used by Kobe Steel on a variety of products Bulletin No. BMS1000-SPEC-NR4 2302005SF Printed in Japan
and in the names of a number of Kobe Steel Group companies.