ENGINE

SECTION
FUEL SYSTEM
FL FL

E
CONTENTS
SERVICE INFORMATION ............................ 2 FUEL LEVEL SENSOR UNIT, FUEL FILTER F
AND FUEL PUMP ASSEMBLY ......................... 5
PRECAUTIONS ................................................... 2 Component ............................................................... 5
Precaution for Supplemental Restraint System Removal and Installation .......................................... 5 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................... 2 FUEL TANK ....................................................... 9
Component ............................................................... 9
PREPARATION ................................................... 3 H
Removal and Installation .......................................... 9
Special Service Tool ................................................. 3
Commercial Service Tool .......................................... 3 SERVICE DATA AND SPECIFICATIONS
(SDS) ................................................................. 14 I
FUEL SYSTEM .................................................... 4 Standard and Limit ..................................................14
Checking Fuel Line ................................................... 4
General Precaution ................................................... 4
J

Revision: May 2007 FL-1 2008 Versa

 PRECAUTIONS
< SERVICE INFORMATION >
SERVICE INFORMATION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000001703094

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

Revision: May 2007 FL-2 2008 Versa

 PREPARATION
< SERVICE INFORMATION >
PREPARATION
A
Special Service Tool INFOID:0000000001703095

The actual shapes of the Kent-Moore tools may differ from those of the special tools illustrated here. FL

Tool number Description

(Kent-Moore No.)
Tool name C
KV991J0090 Removing and installing fuel tank lock ring
(J-46214)
Fuel tank lock ring tool D

E
LBIA0353E

Commercial Service Tool INFOID:0000000001703096 F

Tool name Description

G
Power tools Loosening bolts and nuts

I
PBIC0190E

Revision: May 2007 FL-3 2008 Versa

 FUEL SYSTEM
< SERVICE INFORMATION >
FUEL SYSTEM
Checking Fuel Line INFOID:0000000001703097

Inspect fuel lines, fuel filler cap and fuel tank for improper attach-
ment, leaks, cracks, damage, loose connections, chafing or deterio-
ration.
If necessary, repair or replace damaged parts.

SMA803A

General Precaution INFOID:0000000001703098

WARNING:
When replacing fuel line parts, be sure to observe the following.
• Put a “CAUTION: FLAMMABLE” sign in the work area.
• Be sure to work in a well ventilated area and have a CO2 fire extinguisher.
• Do not smoke while working on the fuel system. Keep open flames and sparks away from the work
area.
• Put drained fuel in an explosion-proof container and put the lid on securely. Keep the container in
safe area.
CAUTION:
• Use gasoline required by the regulations for octane number. Refer to GI-4, "Precaution for Fuel
(Unleaded Regular Gasoline Recommended)".
• Before removing fuel line parts, perform the following procedures:
- Release fuel pressure from the fuel lines. Refer to EC-78, "Fuel Pressure Check".
- Disconnect the battery ground cable.
• Always replace O-rings and clamps with new ones.
• Do not kink or twist tubes when they are being installed.
• Perform work on level surface.
• Do not tighten hose clamps excessively to avoid damaging hoses.
• After connecting fuel tube quick connectors, make sure quick connectors are secure.
Ensure that connector and resin tube do not contact any adjacent parts.
• After installing tubes, make sure there is no fuel leakage at connections in the following steps.
- Apply fuel pressure to fuel lines by turning ignition switch ON (without starting the engine). Then
check for fuel leaks at the fuel tube connections.
- Start engine and rev it up and check for fuel leaks at connections.
• Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the
MIL may come on.
• For servicing “Evaporative Emission System” parts, refer to EC-31.
• For servicing "On Board Refueling Vapor Recovery (ORVR)" parts, refer to EC-38.

Revision: May 2007 FL-4 2008 Versa

 FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
< SERVICE INFORMATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
A
Component INFOID:0000000001703099

FL

G
WCIA0590E

1. Lock ring 2. Fuel level sensor unit, fuel filter and fuel pump assembly 3. O-ring
4. Fuel tank
H

Removal and Installation INFOID:0000000001703100

I
REMOVAL
WARNING:
Be sure to read “General Precautions” before working on the fuel system. Refer to FL-4, "General Pre- J
caution" .
1. Check fuel level with the vehicle on a level surface. If the fuel
gauge indicates more than the level as shown (7/8 full), drain K
fuel from the fuel tank until the fuel gauge indicates level as
shown (7/8 full).
NOTE:
L
Fuel will be spilled when removing fuel pump assembly if fuel
level is above the fuel pump assembly installation surface.
• As a guide, fuel level is at the level as shown or below when
approximately 12 (3 1/8 US gal, 2 5/8 Imp gal) of fuel is M
drained from a full fuel tank.
• In case fuel pump does not operate, perform the following pro- KBIA3505J
cedure.
N
a. Insert fuel tubing of less than 25 mm (0.98 in) in diameter into fuel filler tube through fuel filler opening to
drain fuel from fuel filler tube.
b. Disconnect fuel filler hose from fuel filler tube. Refer to FL-9 . O
c. Insert fuel tubing into fuel tank through fuel filler hose to drain fuel from fuel tank.
2. Open fuel door and unscrew the fuel filler cap to release the pressure inside the fuel tank.
3. Release the fuel pressure from the fuel lines. Refer to EC-78, "Fuel Pressure Check" . P
4. Remove rear seat bottom. Refer to SE-14 .
5. Turn the four retainers 90° in a clockwise direction and remove the fuel pump inspection hole cover.

Revision: May 2007 FL-5 2008 Versa

 FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
< SERVICE INFORMATION >
6. Disconnect electrical connector (A) and fuel feed hose quick
connector (B).
• Fuel feed hose (1)
• ⇐ : Vehicle front

WBIA0782E

• Disconnect the quick connector using the following procedure.

- Hold the sides of the connector, push in tabs and pull out the
tube.
- If quick connector and tube on fuel pump assembly are stuck,
push and pull several times until they move. Disconnect them
by pulling.
CAUTION:
• The tube can be removed when the tabs are completely
depressed. Do not twist it more than necessary.
• Do not use any tools to remove the quick connector.
• Keep resin tube away from heat. Be especially careful
when welding near the resin tube.
SFE562A
• Prevent acid liquid such as battery electrolyte, from get-
ting on resin tube.
• Do not bend or twist resin tube during installation and removal.
• To keep the connecting portion clean, free of foreign
materials and to avoid damage, cover them completely
with plastic bags or something similar.
• Do not insert plug to prevent damage to O-ring in quick
connector.

PBIC0163E

7. Remove the lock ring using Tool as shown.

Tool number : KV991J0090 (J-46214)

WBIA0284E

8. Remove fuel level sensor unit, fuel filter and fuel pump assembly (1).
CAUTION:
• Do not bend float arm during removal.
• Do not allow foreign materials to fall into fuel tank. Use a lint free cloth when handling compo-
nents.
• Avoid impacts such as dropping when handling components.
INSPECTION AFTER REMOVAL
Revision: May 2007 FL-6 2008 Versa
 FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
< SERVICE INFORMATION >
Make sure that the fuel level sensor unit, fuel filter and fuel pump is free from defects and foreign materials.
A
INSTALLATION
Installation is in the reverse order of removal.
Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly FL
1. Install O-ring to fuel tank without twisting.
2. Install fuel level sensor unit with aligning mating marks (A) on
fuel tank and fuel level sensor unit as shown. C
• ⇐: Front

PBIC4732E

F
• Turn the lock ring (1) until the lock ring is fully rotated into the
fuel tank lock tabs (A) as shown.
G

I
WBIA0783E

Quick Connector
J
Connect fuel feed tube quick connector using the following procedure.
1. Check the connection for damage or any foreign materials.
2. Align the connector with the tube, then insert the connector straight into the tube until a “click” sound is
K
heard.
3. After connecting, make sure that the connection is secure using the following procedure.
• Visually confirm that the two retainer tabs are secured to the connector.
• Pull the tube and the connector to make sure they are securely L
connected.

PBIC1653E
O

4. Connect electrical harness connector.

Inspection Hole Cover P
• Before installing inspection hole cover, confirm that there are no fuel leaks. Refer to "INSPECTION AFTER
INSTALLATION" .
1. Install inspection hole cover with the front mark (arrow) facing front of vehicle.
2. Lock clips by turning counterclockwise.
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
Revision: May 2007 FL-7 2008 Versa
 FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
< SERVICE INFORMATION >
1. Turn ignition switch “ON” (without starting the engine), to check the connections for fuel leaks with the
electric fuel pump applying pressure to the fuel piping.
2. Start the engine and let it idle to check that there are no fuel leaks at the fuel system connections.

Revision: May 2007 FL-8 2008 Versa

 FUEL TANK
< SERVICE INFORMATION >
FUEL TANK
A
Component INFOID:0000000001703101

FL

J
WCIA0591E

1. Lock ring 2. Fuel pump 3. O-ring K

4. Fuel tank 5. Fuel tank band (LH) 6. Fuel tank band (RH)
7. EVAP hose 8. Hose clamp 9. Fuel filler hose
10. Hose clamp 11. Fuel filler pipe shield 12. Fuel filler tube L
13. Grommet 14. Fuel filler cap ⇐ Front of vehicle

Removal and Installation INFOID:0000000001703102 M

REMOVAL
WARNING: N
Be sure to read “General Precautions” when working on the fuel system. Refer to FL-4, "General Pre-
caution" .
1. Drain fuel from fuel tank if necessary. Refer to FL-5, "Removal and Installation" . O
CAUTION:
• Because fuel tank becomes unstable when installing/removing, fuel should be drained if the
level exceeds specification FL-5, "Removal and Installation" .
• Situate vehicle on a flat and solid surface. P
2. Open fuel door and unscrew the fuel filler cap to release the pressure inside the fuel tank.
3. Release the fuel pressure from the fuel lines. Refer to EC-78, "Fuel Pressure Check" .
4. Remove rear seat bottom. Refer to SE-14 .
5. Turn the three retainers 90° in a clockwise direction and remove the fuel pump inspection hole cover.

Revision: May 2007 FL-9 2008 Versa

 FUEL TANK
< SERVICE INFORMATION >
Disconnect electrical connector (A) and fuel feed hose quick connec-
tor (B).
• Fuel feed hose (1)
• ⇐ : Vehicle front

WBIA0782E

• Disconnect the quick connector using the following procedure.

- Hold the sides of the connector, push in tabs and pull out the tube.
- If quick connector and tube on fuel pump assembly are stuck, push
and pull several times until they move. Disconnect them by pulling.
CAUTION:
• The tube can be removed when the tabs are completely
depressed. Do not twist it more than necessary.
• Do not use any tools to remove the quick connector.
• Keep resin tube away from heat. Be especially careful when
welding near the resin tube.
• Prevent acid liquid such as battery electrolyte, from getting
on resin tube.
SFE562A
• Do not bend or twist resin tube during installation and
removal.
• To keep the connecting portion clean, free of foreign materi-
als and to avoid damage, cover them completely with plastic
bags or something similar.
• Do not insert plug to prevent damage to O-ring in quick con-
nector.

PBIC0163E

6. Remove center exhaust tube. Refer to EX-4 .

7. Remove exhaust heat shields.
8. Disconnect parking brake cables (1) from the lower surface of
fuel tank and axle and position the parking brake cables (1) out
of the way.

PBIC3786E

Revision: May 2007 FL-10 2008 Versa

 FUEL TANK
< SERVICE INFORMATION >
9. Remove brake tube protector (1) from rear axle (2).
A

FL

WBIA0764E

D
10. Loosen fuel filler hose clamp (3) and remove fuel filler hose (1)
from fuel tank (2).
CAUTION:
E
Do not remove fuel filler hose (1) from fuel filler tube. Do not
allow contact with the suspension during installation. When
removing fuel filler hose (1) at the fuel filler tube, mark com-
ponents for alignment. F

G
WBIA0765E

11. Remove vent hose (1) and EVAP hose (2) at rear of fuel tank.
H
• Disconnect vent hose and EVAP hose quick connectors using
the following procedures.
a. Pinch retaining tabs (A) of vent hose quick connector and
remove vent hose (1). I
b. Slide sleeve (B) of EVAP hose quick connector and remove
EVAP hose (2).
• If hoses are stuck, push and pull several times until they move J
freely, and disconnect.

WBIA0766E
K

CAUTION:
• The tube can be removed when the tabs are completely depressed. Do not twist it more than L
necessary.
• Do not use any tools to remove the quick connector.
• Keep the resin tube away from heat. Be especially careful when welding near the tube.
• Prevent acid liquid such as battery electrolyte, from getting on the resin tube. M
• Do not bend or twist the tube during installation and removal.
• Do not insert plug that may cause damage to O-ring in quick connector.
• To keep the connecting portion clean and to avoid dam- N
age and foreign materials, cover them completely with
plastic bags or something similar.

PBIC0163E

Revision: May 2007 FL-11 2008 Versa

 FUEL TANK
< SERVICE INFORMATION >
12. Support center of fuel tank (1) with transmission jack (A).
CAUTION:
Securely support the fuel tank with a suitable tool (B).
13. Remove fuel tank bands (RH and LH).
14. Lower transmission jack carefully to remove fuel tank while sup-
porting it by hand.
CAUTION:
Fuel tank may be in an unstable position because of the
shape of fuel tank bottom. Be sure to support tank securely.

PBIC3792E

INSTALLATION
Installation is in the reverse order of removal.
EVAP Canister
1. Check the connection for damage or any foreign materials.
2. Align the connector with the tube, then insert the connector straight into the tube until a “click” sound is
heard.
3. After connecting, make sure that the connection is secure.
• Pull the tube and the connector to make sure they are securely connected.
Fuel Tank Bands
Install the fuel tank bands in the proper position by referring to the identification stamp mark “R” and “L” on the
end
1. While supporting the fuel tank, install bolts 1, 3 and 4 to support
the tank, but do not fully tighten.
• ⇐ : Front
2. Install bolt 2 while positioning the fuel tank toward the front of
the vehicle. Tighten bolt 2 to specified torque.
3. Tighten bolts 1, 3 and 4 to specified torque.

WBIA0847E

Fuel Filler Hose

• Insert fuel filler hose to the length below.

Fuel filler install length : 35mm (1.38 in)

• Be sure hose clamp is not placed on swelled area of fuel filler tube.
EVAP Hose

Revision: May 2007 FL-12 2008 Versa

 FUEL TANK
< SERVICE INFORMATION >
1. Check connections for damage or foreign material.
2. Align the matching quick connector (A) with the center of EVAP A
hose (1), and insert quick connector (A) straight until it clicks.
3. After connecting, pull on quick connector (A) and EVAP hose (1)
by hand. Make sure connections are secure. FL

WBIA0767E

D
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn ignition switch “ON” (without starting the engine), to check the connections for fuel leaks with the
E
electric fuel pump applying pressure to the fuel piping.
2. Start the engine and let it idle to check that there are no fuel leaks at the fuel system connections.
F

Revision: May 2007 FL-13 2008 Versa

 SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE INFORMATION >
SERVICE DATA AND SPECIFICATIONS (SDS)
Standard and Limit INFOID:0000000001703103

FUEL TANK
Unit: (US gal, Imp gal)

Fuel tank capacity 50.0 (13 1/4, 11)

Fuel recommendation Refer to MA-10

Revision: May 2007 FL-14 2008 Versa