CLIENT :TVS INDUSTRIAL AND LOGISTICS PARKS PRIVATE LIMITED, CHENNAI

PROJECT : CONSTRUCTION OF LIGHT MANUFACTURING FACILITY AT CUTTACK-ODISHA

BUILDING -01 INTERNAL WAREHOUSE WORKS
PHASE 01 -SUMMARY COSTING SHEET
SL.NO DESCRIPTION OF WORKS BOQ AMOUNT REMARKS
CIVIL WORKS
1 Main Building civil works 37,908,310
2 Drivers rest room 3,643,965
3 Collection tank-25 KLD 02 Nos 1,002,385

Plumbing works Floor (Driver restroom, Workers

4 8,114,800
& Supervisors Toilet, Canteen and Security rooms)

Total Amount 50,669,460.00

Add GST @ 18% 9,120,502.80
Grand Total Amount(Inclusive of taxes) 59,789,962.80
 TVS INDUSTRIAL AND LOGISTICS PARKS PRIVATE LIMITED, CHENNAI
Project : CONSTRUCTION OF LIGHT MANUFACTURING FACILITY AT CUTTACK -ODISHA
BILL OF QUANTITIES - MAIN BUILDING & BAD GOOD ROOM
RATE AMOUNT
SL.NO DESCRIPTION OF WORKS UNIT REMARKS
QTY INR INR
A LAND DEVELOPEMENT WORKS
Carrying out minor site clearing work including removal of trees of any girth, small bushes, roots, boulders etc, so as to
make site access, ground workable for further construction works measured on cleared area, wherever required as
directed by Engineer-in charge, and disposing off the materials to an unobjectionable location outside Owner's premises,
irrespective of any lead and lift as directed by Engineer In Charge. (This item does not include major earthwork)
A.1 Part of Tender including
Note: Contractor required to obtain necessary permissions for removal of trees and its disposal. Contractor shall take
permission of Engineer-In-Charge on area to be executed under this item before start of work.

B EXCAVATION AND BACK FILLING WORKS

Excavation in all types of soil and soft disintegrated rock but excluding laterite and hard rock. At all types of foundation
structures, plinth beams, etc. to required levels, grades, and dressing with the complete finish as per specifications and
directions of the Engineer In-charge, Including subsoil backfilling around the foundations and plinth beams with selected
excavated earth in 200mm each layers with watering and consolidation, compaction of 200mm thickness of (Layer by
B.1 layer) etc. wherever necessary disposal of the surplus excavated material shall be dumped site. The Quoted rate shall be
inclusive of complete tools, Equipment, and labour with the complete finish. as per the instruction of the Engineer in
charge.
Note: (Main building Footing, Toilet footing, Plinth beam, Fire Staircase, and dock pits)

B.1.1 0.0M - 2.0M from Existing Ground level 3200.00 Cum 245 784,000
B.1.2 2.0M - 4.0M depth 399.00 Cum 315 125,685
Excavation in all types of Laterite rock but excluding hard rock.At all types of foundation structures, plinth beams, etc. to
required levels, grades, and dressing with the complete finish as per specifications and directions of the Engineer in-
charge, Including subsoil backfilling (Available soil) around foundations and plinth beam with selected excavated earth
in 200mm each layer with proper watering and consolidation, compaction of 200mm thickness (Layer by layer) etc.
wherever necessary disposal of the surplus excavated material shall be dumped site. The Quoted rate shall be inclusive of
B.2 complete tools, equipment, and labour with a complete finish. as per the instruction of the Engineer in charge.

Note: (Main building Footing, Toilet footing, Plinth beam, Fire Staircase, and dock pits)

a) 0.0M - 2.0M from Existing Ground level 240.00 Cum 500 120,000
b) 2.0M - 4.0M depth 160.00 Cum 750 120,000
De-watering in Excavated pits By using Electrical motorized pumps ( This item shall be applicable only for dewatering of
B.2.1 Rain water duly approved by Engineer-in-charge. The pump capacity shall be 5HP and power shall be arranged by 150.00 Hrs 350 52,500
contractor at own cost
De-watering in Excavated pits By using Mechanical pumps including all fuel, consumables, etc, complete ( This item shall
B.2.2 be applicable only for dewatering of Rain water duly approved by Engineer-in-charge) The pump capacity shall be 5HP 150.00 Hrs 750 112,500
and power shall be arranged by contractor at own cost

Filling of available earth-approved material brought from surplus excavated stuff available at the site including re-
excavation and shifting of stack wherever required, including filling in layers of 250mm thick, watering, compaction, and
consolidation with Vibratory roller at each layer, dressing, leveling, etc. complete. The proctor density of such compacted
B.3 50.00 Cum 150 7,500
filling shall not be less than 95% of a standard proctor. Proctor density tests ( Core Method/Sand Replacement Method )
shall be carried out at the site to ensure the Proctor density of compacted filling of each layer. It will be carried out with
the witness of the Engineer-in-charge.

Providing and backfilling using approved Gravel (Mountain earth) / Moorum in uniform layers not exceeding 250mm
compacted thickness including watering, Consolidation, and compaction has to be done and The proctor density of such
compacted filling soil shall not be less than 97% of a standard proctor. Proctor density tests ( Core Method / Sand
B.4 Replacement Method ) shall be carried out at the site to ensure the Proctor density of compacted filling of each layer by 2789.00 Cum 1,250 3,486,250
using a vibrator roller with a capacity of 8 to 10-ton, The quoted rate to be inclusive of transportation, and any other
accessories equipment all labours, etc., It will be carried out with the witness of the Engineer-in-charge. The Compacted
filling gravel/Moorum sand shall be 300mm.

Providing and backfilling to using River sand for the flooring work of approved quality to any section and depth carried
out in uniform layers of not exceeding 250mm of compacted thickness, well watered, rammed, and consolidated to 85% of
B.5 relative density, including the cost of sand, and transportation, loading, unloading, rolling with 8 to 10 ton power roller, 1395.00 Cum 2,850 3,975,750
equipment, all labor, etc. complete including the temporary works for confining the sand, if any required. The filling
thick of river sand shall be 150mm.

Providing, laying, spreading, and compacting of approved and graded stone aggregate wet mixed macadam (As per
MORTH 2001, Specification No.406) with proper mixing of water at optimum moisture content in a mechanical mix
plant with clean machine crushed black aggregate in proportions 40% - 20mm metal, 30% - 12mm metal and 30% - 40mm
metal with dust (mass equivalent to 2.38 Tons / CuM.) all permeated with water to dense mass on the prepared sub
base /base course and the thickness of WMM shall be 150mm with well-prepared surface and compacting with a
B.6 1440.00 Cum 2,850 4,104,000
vibratory power roller of 10 Ton to achieve the proctor density of 98%. The mode of measurement shall be the actual
drawing area only. A vibratory roller with a static weight of (80-100 KN) will be used and it will be carried out with the
witness of the Engineer-in-charge.

Note: The WMM quantity Considered for the entire warehouse

Providing and laying of Granular Sub-Base(GSB) of approved quality and size below grade slabs, foundations at any
depth and to any thickness carried out by Mix in Place Method (Construction of granular sub-base by providing machine
crushed close graded aggregate of Grade - I, spreading in uniform layers with a motor grader on a prepared surface,
B.7 mixing by mix in-place method with rotavator at OMC, and compacting with 8-10 MT mechanical roller / vibratory roller QRO Cum 3,500 _
to achieve the desired density, complete as per MORTH Specification 401): for grading-I Material Stone aggregate - 53 - 9.5
mm - 50%, 9.5 - 2.36 mm - 20%, 2.36 mm and below - 30%, etc complete all as per specifications and instructions of the
project manager. The Quoted rate is inclusive of all materials, labor, machinery, etc.

Providing Pre – Constructional Anti – Termite Treatment and creating a Chemical Barrier to the building by injecting
chemical emulsion of required concentration under floor area(Internal Floor area) as per instructions of chemical
manufacturer and all as directed. The treatment shall be carried out strictly in accordance with the technical specification
and conforming to IS 6313 or equivalent BS specification. The chemical to be used as insecticide for the treatment shall be
Biflex Tc, TC stands for Termiticide Concentrate for Termite Control (Bifenthrin) and the application shall be diluted 1
part of chemical Biflex Tc with 49 parts of water to get 0.05% emulsion and strictly in accordance with the manufacturer’s
specification. The chemical to be used for the treatment and concentration of the chemical solutions should be as laid
down in IS - 6313 Part II. The work should be carried out by an approved and registered specialist pest control agency
B.8 only. Tenderer to furnish the name of the proposed specialist firm). Plinth area of the building at ground floor only will be 9291.00 Sqm 110 1,022,010
measured for payment.(Warranty certificate to be Provided for 5 years )
Note: The ATT Quantity Considered for the entire warehouse
 C CONCRETING WORKS
Providing and laying plain cement concrete of mix 1:4:8 in all foundations, plinths, floors, etc. using 20mm graded stone
aggregate, Msand/River sand as Fine Aggregate, including tampering, and curing. with the complete finish as per the
C.1 157.00 Cum 5,900 926,300
drawing. (With Flyash as per Design mix shall be used as part replacement of OPC Cement)
Note:(Main building Footing, Toilet footing, Plinth beam, Fire Staircase, and dock pits )

Providing and laying machine batched and machine mixed Reinforced cement concrete of M-25 grade with Minimum
Cement Content as per IS mix design with OPC cement. (With Flyash asper Design Mix shall be used as part
replacement of OPC Cement) using 20mm down-graded machine crushed stone aggregate, M sand/River sand as Fine
C.2 Aggregate, in footings, Pedestals, columns, Plinth beams, rafts, walls, and Slab (From foundation to FFL), With complete
finish and Curing, etc., as per the drawing and the directions of the Engineer-in-charge. (The cost of shuttering and
reinforcement steel will be measured separately.

C.2.1 In Footings/staircase Footing/Dock pit Raft 432.00 Cum 6,850 2,959,200

C.2.2 In Plinth beams 88.00 Cum 6,850 602,800
C.2.3 In Columns & Pedestals 199.00 Cum 6,850 1,363,150
in Retaining Walls / RCC Walls / Dock pit Walls / Fire Staircase concrete (waist slab, steps&landing)/Rcc Culvert Walls/
C.2.4 47.00 Cum 6,850 321,950
Ramp walls / Ramp slabs
Only Fixing/embedding of Foundation Bolts in RCC Pedestals/foundations at any specified level including maintaining
the accuracy towards the line, level position, etc. complete as directed by the Engineer In Charge (Foundation Bolts size
will be up to 32mm dia of 1500mm length and template will be supplied by the client. The contractor should take care of
its threads and protect them from rusting by applying grease and cotton waste ) The contractor shall ensure all the
installed anchor bolts after completion of PEB erection works cleaned by using grease, oil with required labor and
C.3 accessories at the time of handing over (The quoted Rate shall be inclusive of handling charges, welding of bolts with 816.00 Nos 400 326,400
TMT bars, Total station marking, fixing, level checking etc., )
Note:
After completion of 100% Bolt fixing the complete MS template shall be handed over to the Engineer In Charge of
necessary cleaning. The anchor bolt will be supplied by the client.

Providing and laying machine batched and machine mixed reinforced cement concrete of M-25 grade with Minimum
Cement Content as per IS mix design with OPC cement. ( With Flyash asper Design Mix shall be used as part
replacement of OPC Cement) ABOVE FFL up to 4.5m height using 20 mm and downgraded machine crushed stone
C.4 aggregate, M sand/River sand as Fine Aggregate, in the superstructure in columns, lintels, beams, sunshades, slabs, facia,
brackets, drops, walls, etc. including providing pockets, cutouts, vibrating, tamping, curing etc., complete (The cost of
shuttering and reinforcement will be measured separately)
Note : (Main building Footing, Toilet footing, Plinth beam, Fire Staircase, and dock pits)
C.4.1 In Columns/Mullions 33.00 Cum 7,250 239,250
C.4.2 In Roof beam & Roof slab,Lintels & Sunshades 34.00 Cum 7,250 246,500
C.4.3 In Fire staircase waist slab, steps&landing / Ramp slab & walls QRO Cum 7,250 _
Supplying & Laying of 300 Micron LDPE Sheet with 200mm lapping (Overlapping Joints)- Rate is applicable only for laid
C.5 9747.00 Sqm 110 1,072,170
Plan Floor Area and no overlaps will be paid seperately- White colour LDPE sheet shall be considered.
Providing and applying Lithum silicate (Approved makes shall be ULTRASIL Li+ of EUCLID chemicals, Flowcrete india
Pvt ltd, Sika or other approved Equivalent )densifier of 5stage finishing as per the below specification, by mean of
mechanical spray or can be done manully by brush/ wipers and covering with Polyethelene sheet.polishing of concrete
using resin pads 100 Grit,400 Grit ,800 Grit, 1500 Grit, after that apply one coat of Sealar using PRO POLISH GUARD ,
Finnally burnish using high spread burnisher . The design and construction of the floor should be adequate to withstand
C.6 the traffic, impact and such other loads the floor is likely to be exposed to. The concrete used for flooring should be > M25 QRO Sqm 3,000 _
grade and should be free of bleed & segregation and should not contain more than 3% air. The placing and application
shall be carried out as per manufacturers specification etc complete. Work should be executed by specialist flooring
company.Approved makes shall be ULTRASIL Li+ of EUCLID chemicals, Flowcrete india Pvt ltd, Sika or other
approved Equivalent

Providing and grouting below the base plate of the columns by using G-P2 Non-shrink grout of Fosroc chemicals.
C.7 3.00 Cum 68,000 204,000
including all necessary leads,lifts & shuttering, cleaning and curing if applicable etc all complete
D REINFORCEMENT STEEL WORKS

FE500 - Supplying, fabricating, and tying in position at all levels of steel reinforcement for all RCC works including
cutting, bending, and binding with 18 gauge M.S.annealed binding wire or by welding if required, and rate-inclusive of
D.1 all lifting, leading & precast concrete cover blocks with ribs/PVC Cover blocks with complete finish as instructed by 62.00 M.ton 77,000 4,774,000
Engineer In charge.
NOTE: Laps, Spacer bars, and Chairs will be measured for payments, and wastages not considered for payment.

Only Laying and tying in position at all levels & locations of Welded Wire Fabric Mesh Reinforcement (WWF- TATA
STEEL/Equivalent). The approx Size of the mesh is (6m x 2.45m). Rate to be inclusive of Unloading of weld mesh and
Placing the mesh nearby the Flooring Bay and also cost inclusive of precast concrete cover block for the flooring work
D.2 38.00 M.ton 13,500 513,000
with the size of 75x75 mm with rib and Binding with 18 gauge M.S. annealed binding wire or by welding if required, as
per the drawing and instructions of engineer-in-charge.
Note : Weld mesh supplied by client.
E SHUTTERING WORKS
 Providing and fixing of Good Quality Film Coated Plywood centering and shuttering as required in all foundations,
basement, and up to finished floor level in footings, columns, pedestals, beams, rafts, with necessary strutting, bracing,
propping, etc., and keeping the same in position during concreting and removing the same after a specified period, etc.
E.1 With a complete finish. From foundation bottom level to Finished Floor Level (Maximum repetitions of shuttering
plywood shall be 5 repetitions only)
Note: FFL means floor finished level of Shop Floor and Main building Footing, Toilet footing, Plinth beam, Fire
Staircase, and dock pits.
E.1.1 In PCC 239.00 Sqm 700 167,300
E.1.2 In Footings/Foundations /dock pit Raft /Rcc Culvert raft 687.00 Sqm 750 515,250
E.1.3 In Plinth beams 620.00 Sqm 750 465,000
E.1.4 In Columns & Pedestals. 1168.00 Sqm 750 876,000
in Retaining Walls / RCC Walls / Dock pit Walls / Fire Staircase concrete (waist slab, steps&landing)/Rcc Culvert Walls/
E.1.5 371.00 Sqm 750 278,250
Ramp walls / Ramp slabs
Providing and fixing plywood or steel sheet centering and shuttering as required in the superstructure in R.C.C.
columns, beams, lintels, sunshades, slabs, etc., and keeping the same in position during concreting and removing the same
E.2
after a specified period etc., complete up to 4.50M height from finished floor level (Maximum repetitions of shuttering
plywood shall be 5 repetitions only)
E.2.1 In Columns/Mullions 581.00 Sqm 850 493,850
E.2.3 In Roof beam/Roof slab/Lintels & Sunshades 389.00 Sqm 850 330,650
F MASONRY WORKS
Providing and constructing cement concrete Fly ash bricks work from FFL to 4.5m levels in cement mortar 1:5 using
standard size of solid cement concrete blocks of thickness as given below, with minimum compressive strength of 5
N/Sq.mm. conforming to IS 2185 or equivalent BS and Fly ash conforming to IS : 3812 (Part III)-1966* may be used for part
F.1
replacement of fine aggregate up to a limit of 20 percent as per the drawing.
Note : Main building Footing, Toilet footing, Plinth beam, Fire Staircase, and dock pits.

F.1.1 Solid block wall of 200 mm thick QRO Cum 7,250 _

F.1.2 Solid block wall of 300 mm thick - For Ramp side wall 32.00 Cum 7,250 232,000
Providing and constructing Fly ash bricks work using ground moulded well burnt bricks with minimum compressive
F.2 strength of 35 Kg per Sqcm in cement mortar 1:5 From the top of Plinth beam to FFL as per the direction of Engineer In QRO Cum 7,250 _
Charge.

Providing and laying of Fly ash bricks with 350mm thick masonry work at all types of structures in cement mortar 1:5 by
using standard size of fly ash bricks of approved make with minimum crushing strength 10N/mm2. including all
F.2.1 110.00 Cum 7,250 797,500
scaffolding, staging, striking off extra mortar, Pointing, lifting, leading curing, etc. The Fly ash bricks work shall be done
from above the plinth to FFL (Finished Floor level).

Providing and laying 150mm thick Fly ash brick for the wall from FFL to 4.5m levels in Cement Mortar 1:4 with
minimum crushing strength 5N/mm2 including all scaffolding, staging, striking off extra mortar, Pointing, lifting,
leading, and curing. Including placing M20 grade reinforced cement concrete with binders and 80mm thick concrete using
a coarse graded aggregate of 12mm and downsize, reinforced with 2 nos. of 8mm dia. Fe500 grade steel (Single layer) and
F.3 6 mm dia. Mild steel stirrups at every 200mm c/c. The rate shall include the cost of reinforcements and tying in position 842.00 Sqm 1,250 1,052,500
using binding wire made out of 18 gauge MS annealed, formwork, scaffolding, raking out, including all materials, labor,
etc. with the complete finish as per the instruction of the Engineer in charge.

Providing and laying Fly ash brick Masonry wall of 100 mm thick from FFL to 4.5m levels With C.M 1: 4 including all
scaffolding, staging, striking off extra mortar, Pointing, Lifting, leading, and curing. Including placing of M20 grade
reinforced cement concrete with binders and 80mm thick concrete using a coarse graded aggregate of 12 mm and
F.4 downsize, reinforced with 2 nos. of 8 mm dia. Fe 500 (single layer) and 6 mm dia. Mild steel stirrups at 200 mm c/c. The 43.00 Sqm 1,150 49,450
rate shall include the cost of reinforcing steel and tying in position using binding wire made out of 18 gauge MS annealed,
formwork, scaffolding, raking out, including all materials, labor, etc. with the complete finish as per the instruction of the
Engineer in charge.

G FLOORING & FINISHING WORKS

Prepare the surface of levelling course and lay 50mm thick grano concrete flooring of mix 1:1.5:3 using 6mm down size
G.1 blue granite chips, River sand as Fine Aggregate to the given levels including laying in alternate panels if required, curing QRO Sqm 650 _
and finishing the surface smooth with power trowel to given levels etc., complete.
Prepare the surfaces of levelling course/R.C. slab and Providing & Laying of vitrified ceramic tiles flooring of approved
make and size and laid over 20mm thick base mortar in c.m. 1:3, Msand/River sand as Fine Aggregate, including
G.2 34.00 Sqm 1,850 62,900
finishing the butt joints with grouting to shade of tile to given lines and levels with proper cleaning. Basic Rate = Rs. 60
per Sq.ft.
Prepare the surfaces of brick masonry and lay glazed tiles dado of approved make and size and laid over 20mm thick base
G.3 mortar in c.m. 1:3, Riversand Fine Aggregate, including finishing the butt joints clean to given lines and levels.Basic Rate 162.00 Sqm 1,750 283,500
= Rs. 45 per Sq.ft.
Prepare the surfaces of all ceiling and sofits of R.C. Surfaces and plaster in C:M 1:3, Msand/Riversand as Fine Aggregate,
G.4 12mm thick finished smooth with trowel and sponge including hacking, scaffolding, curing etc., complete at all levels 59.00 Sqm 450 26,550
(Toilet Ceiling)
Prepare the surface of all Internal walls Plaster with cement mortar 1:5 (1 cement: 5 fine sand) of 12 mm thick including
GI mesh of nominal thickness at the junctions of masonry and concrete works to a width of 100 to 125mm including tying
in position with suitable clamps/screws, necessary hacking, staging,scaffolding and curing at all levels and elevations
G.5 1915.00 Sqm 500 957,500
etc.as complete with all respects complying with relevant standard specification, as directed. Before proceeding internal
wall plastering works contractor shall do packing of chiesled portitions filled with proper CM 1: 5 for the all MEP
services.

Prepare the surfaces of all external walls plaster in c.m. 1:4, by using a waterproofing compound of “CICO No.1 or
equivalent“ as per Manufacturer's Specification, Rivers sand/M sand as Fine Aggregate, 18mm thick finished smooth
G.6 with wood float, GI mesh of nominal thickness at the junctions of masonry and concrete works to a width of mesh 100 to 1687.00 Sqm 600 1,012,200
125mm including tying in position with suitable clamps/screws, necessary hacking, staging, scaffolding and curing at all
levels and elevations, etc. as complete with all respects complying with relevant standard specification, as directed.

H PAINTING WORKS
Providing and applying 2 coats of Acrylic emulsion with low VOC content including one base coat of primer of
approved make and two or more coats of Acrylic emulsion as per manufacturer specifications and make and sample
mock-up to be approved by the Engineer In Charge. The rate shall be inclusive of necessary scaffolding and staging etc.
H.1 1915.00 Sqm 300 574,500
With the complete finish, all respects comply with relevant standard specifications, as directed by the Engineer in charge
(Internal walls).
Note: The colour has to be finalized by the client

Providing and applying 2 coats of weatherproof Acrylic emulsion paint with low VOC content including one base coat
of primer and two or more coats of Exterior Emulsion paint as per manufacturer specifications and making sample mock-
up to be approved by the Engineer In Charge. The rate shall be inclusive of necessary scaffolding or staging etc. with the
H.2 1687.00 Sqm 400 674,800
complete finish, in all respects complying with relevant standard specifications, as directed by the Engineer in charge
(External walls).
Note: The colour has to be finalized by the client
 I STEEL WORKS
Providing, fabricating and fixing 1.2 m height hand raills with M.S. pipe of medium class at all height and locations (as
per drawing) with base plate of 150 x 150 x 6 thk, and toe plate of 50mm high x 6mm thk including all necessary fixtures,
I.1 holdfasts, supports, painting with one coat of zinc chromate primer and two coats of synthetic enamel paint etc complete 1500.00 Kgs 175 262,500
as directed by Engineer In Charge.(The quoted rate shall be inclusive of scaffolding, welding with TMT bars and required
tools and tackles, etc.)
Providing fabricating and fixing in position M.S.insert angles of varies sizes and thickness at all levels including welding
M.S./Tor steel hold fast and one coat of zinc chromate primer and two coats of synthetic enamel paint as per approved
I.2 2245.00 Kgs 115 258,175
make and shade, with complete finish for Dock levelers. (The quoted rate shall be inclusive of scaffolding, welding with
TMT bars and required tools and tackles, etc..)
J FALSE CEILING WORKS / TOILETS / OFFICES

Providing and fixing in position multi level GYPSUM board false-ceiling suspended on G.I. frame work using Perimeter
channel, Intermediate channel, Ceiling section and 12.5mm thick tapered edge gypsum plaster board. The board shall be
finished with requisite filler, paper tape, finisher and primer suitable for Gypsum plaster boards & finishing the same
with 3 coats of acrylic emulsion paint as approved. Rate to include making necessary cut-outs/openings for light fittings,
J.1 diffusers etc. All components to be of India Gypsum & all spacings should match their recommendation & standards.The QRO Sqm 1,800 _
rate shall include making cutouts for varies AC duct, cable tray, conduit pipe, etc for specified size, for which no extra will
be paid separately. Providing polyseal material to fill the gap between duct or cable tray and partition board to make air
tight.
Note :( Plan area will measured and paid)

Providing and fixing Armstrong or Equivalent Grid type false ceiling of making each tile size 24”x24” and 1" thick at all
levels as shown in the drawing. Rate shall be inclusive of providing the total system with installation as per the
recommendation of Manufacturer. The contractor has to maintain all tiles in good order and before handing over the
J.2 site.The rate inclusive of providing required GI frame with required supports and accessories,etc,Complete finish.The rate 62.00 Sqm 2,600 161,200
shall include making cutouts for conduit pipe, etc (For Toilet Area).
Note :(Plan area will be measured and paid)

K STRUCTURAL STEEL WORKS (BAD GOOD ROOM )

Supplying and fixing of structural steel supports all vertical horizandal, framings, claddings, by using channel &
ISMB/ISMC as per drawing upto 5m height from ground level and inclusive of baseplates,anchor bolts,cutting and
K.1 weldind and 1coat of zinc chromate primer and 2coat of synthetic enamel painting with complete finish..Rate includes All 697.00 Kgs 115 80,155
material, labour, Scaffolding, etc, complete.
Providing and Fixing of 0.50mm color coated galavalume sheet and with necessary accessories screws,laps, scaffolding,
K.2 47.00 Sqm 1,250 58,750
labour and complete finish ( The make shall be JSW / TATA BLUESCOPE )
L PLINTH PROTECTION FOR ALL BUILDINGS
Prepare the surface of earth around the building by compacting using Mechanical vibrators and providing and laying
L.1 cement concrete of mix 1:2:4 in levelling course using 20mm and down graded stone aggregate, compacting, curing, QRO Cum 10,500 _
finishing to given levels etc., complete.
M MISCELLANEOUS WORKS
RCC Core Cutting Dia & Depth below mentioed dia as directed by Site incharge in RCC retaining walls, RCC Drain
M.1
walls by using electrical equipments and required accessories, etc...
M.1.1 Core Cutting 75mm dia 200mm depth 2.00 Nos 5,000 10,000
M.1.2 Core Cutting 100mm dia 200mm depth 2.00 Nos 7,500 15,000
M.1.3 Core Cutting 150mm dia 200mm depth 2.00 Nos 10,000 20,000
M.1.4 Core Cutting 200mm dia 200mm depth 2.00 Nos 12,500 25,000
M.1.5 Core Cutting 300mm dia 200mm depth 2.00 Nos 15,000 30,000
N UPVC Ventilator
Providing and fixing of factory made Sliding window (White Colour) complete, comprising uPVC multi-chambered frame
of size 67mm x 54mm having uPVC roller track on top and uPVC sash of size 60mm x 47mm. All corners of frame and
sash will be fusion welded and duly reinforced with G.I. section 1.2 mm. After placing 5mm float or prescribed glass in
the sash, uPVC glazing bead, interlock, EPDM gasket, brush will be provided including hardware, i.e., touch lock and
rollers & proper including hardware, i.e., touch lock and rollers & proper drainage system shall be provided. Window
will be fixed to the wall with 100mm long and 8mm dia. Fasteners and complete in all respect as per direction of Engineer-
In-Charge. The shutter section shall be made out of extruded rigid uPVC with internal side reinforced with provision of
5mm thick clear glass as per requirement

Profile of frame & sash shall be mitered cut and fusion welded at all corners, mullion (if required) shall be also fusion
welded including drilling of holes for fixing hardware and drainage of water, etc. After fixing the frame the gap between
the frame and the adjacent finished wall shall be filled with weatherproof silicon sealant over the backer rod of the
required size and of approved quality, all complete as per the approved drawing & and direction of the Engineer-in-
H.1 Charge.

Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of
profile shall be acceptable.
Providing and fixing of factory made Sliding window (White Colour) complete, comprising uPVC multi-chambered frame
of size 67mm x 54mm having uPVC roller track on top and uPVC sash of size 60mm x 47mm. All corners of frame and
sash will be fusion welded and duly reinforced with G.I. section 1.2 mm. After placing 5mm float or prescribed glass in
the sash, uPVC glazing bead, interlock, EPDM gasket, brush will be provided including proper hardware, i.e., touch lock
and rollers & proper including hardware, i.e., touch lock and rollers & proper drainage system shall be provided.
Window will be fixed to the wall with 100mm long and 8mm diameter. Fasteners and complete in all respects as per
direction of Engineer-In-Charge. The shutter section shall be made out of extruded rigid uPVC with an internal side
reinforced with a provision of 5mm thick clear glass as per requirement. The Quoted Rate Shall be inclusive (Aluminum
Wire Mesh)

1200mm x 1500mm
2.00 Sqm 12,500 25,000
 Providing and fixing of factory made approved make, uPVC Louver window comprising of uPVC multi-chambered
frame of size 67 mm x 54 mm, duly reinforced with 1.2 mm thick G. I. Section. Both vertical sides of the frame, adjustable
N.2 louver with 4 mm frosted glass and having one lever to adjust the glass including the provision for exhaust fan and will be
fixed to the wall with 100mm long and 8mm dia. Fasteners and complete in all respect as per direction of Engineer-In-
Charge.
N.2.1 600mm x 600mm 4.00 Sqm 12,500 50,000
M Flooring works and cleaning works
Supplying of Concrete & laying of flooring works shall be done by TVS ILP. However Disposal of flooring debris from site
M.1 premises, and final floor cleaning by using mechanical equipment after completion of sealant filling works by flooring 9291.00 Sqm 65 603,915
vendors shall be done by a Civil contractor. (3 times floor deep cleaning shall be considered)
TOTAL BASIC AMOUNT 37,908,310
ADD: GST @18% 6,823,496
GRAND TOTAL 44,731,806
Note:River sand shall be used as a fine aggregate for all civil works
 TVS INDUSTRIAL AND LOGISTICS PARKS PRIVATE LIMITED,
Project : CONSTRUCTION OF LIGHT MANUFACTURING FACILITY AT C
BILL OF QUANTITIES - DRIVER REST ROOM

SL.NO

a)
b)

a)
b)
B

B.1

B.2
B.3

B.4

B.5

C.2

a)
b)
c)
d)

C.3

a)
b)
D

D.1

a)
D.2

a)
b)
c)
d)

a)
b)
F

F.1

F.1.1
F.1.2

F.2

F.3
F.4

H.1

H.2

H.3

H.4

a.

H.5

2
3

J.1

J.2

a)

J.3

a)
 TVS INDUSTRIAL AND LOGISTICS PARKS PRIVATE LIMITED, CHENNAI
Project : CONSTRUCTION OF LIGHT MANUFACTURING FACILITY AT CUTTACK-OD
BILL OF QUANTITIES - DRIVER REST ROOM

DESCRIPTION OF WORKS

EXCAVATION WORKS
Excavation in all types of soil and soft disintegrated rock but excluding laterite and hard rock. At all types of foundation
structures, Footing, column and plinth beams, etc. to required levels, grades, and dressing with the complete finish as per
specifications and directions of the Engineer In-charge, Including subsoil backfilling around the foundations, Column and
plinth beams with selected excavated earth in 200mm each layers with watering and consolidation, compaction of 200mm
thickness of (Layer by layer) etc. wherever necessary disposal of the surplus excavated material shall be dumped site. The
Quoted rate shall be inclusive of complete tools, Equipment, and labour with the complete finish. as per the instruction of
the Engineer in charge.

0.0M - 2.0M from Existing Ground level

2.0M - 4.0M
Excavation in all types of Laterite rock but excluding hard rock.At all types of foundation structures, columns, Pedestals,
plinth beams, etc. to required levels, grades, and dressing with the complete finish as per specifications and directions of
the Engineer charge, Including subsoil backfilling (Available soil ) around foundations and plinth beam with selected
excavated earth in 200mm each layers with proper watering and consolidation, compaction of 200mm thickness (Layer by
layer) etc. wherever necessary disposal of the surplus excavated material shall be dumped site. the quoted rate shall be
inclusive of complete tools, Equipment, and labour with the complete finish. as per the instruction of the Engineer in
charge.

0.0M - 2.0M from Existing Ground level

2.0M - 4.0M depth
FILLING WORKS

Providing and backfilling using approved Gravel (Mountain earth) / Moorum in uniform layers not exceeding 250mm
compacted thickness including watering, Consolidation, and compaction has to be done and The proctor density of such
compacted filling soil shall not be less than 97% of a standard proctor. Proctor density tests ( Core Method / Sand
Replacement Method ) shall be carried out at the site to ensure the Proctor density of compacted filling of each layer by
using a vibrator roller with a capacity of 8 to 10-ton, The quoted rate to be inclusive of transportation, and any other
accessories equipment all labours, etc., It will be carried out with the witness of the Engineer-in-charge.

Providing, laying, spreading, and compacting of approved and graded stone aggregate wet mixed macadam (As per
MORTH 2001, Specification No.406) with proper mixing of water at optimum moisture content in a mechanical mix
plant with clean machine crushed black aggregate in proportions 40% - 20mm metal, 30% - 12mm metal and 30% - 40mm
metal with dust (mass equivalent to 2.38 Tons / CuM.) all permeated with water to dense mass on the prepared sub
base /base course and the thickness of WMM shall be 150mm with well-prepared surface and compacting with a
vibratory power roller of 10 Ton to achieve the proctor density of 98%. The mode of measurement shall be the actual
drawing area only. A vibratory roller with a static weight of (80-100 KN) will be used and it will be carried out with the
witness of the Engineer-in-charge.
Providing Pre – Constructional Anti – Termite Treatment and creating a Chemical Barrier to the building by injecting
chemical emulsion of required concentration under grade slab as per instructions of the chemical manufacturer and all as
directed. The treatment shall be carried out strictly in accordance with the technical specification and conforming to IS
6313 or equivalent BS specification. The chemical to be used as insecticide for the treatment shall be Biflex Tc, TC stands
for Termiticide Concentrate for Termite Control (Bifenthrin) and the application shall be diluted 1 part of chemical Biflex
Tc with 49 parts of water to get 0.05% emulsion and strictly in accordance with the manufacturer’s specification. The
chemical to be used for the treatment and concentration of the chemical solutions should be as laid down in IS - 6313 Part
II. The work should be carried out by an approved and registered specialist pest control agency only. Tenderer to furnish
the name of the proposed specialist firm). Plinth area of the building at the ground floor only will be measured for
payment.(Warranty certificate to be Provided for 5 years )

Supplying & Laying of 300 Micron LDPE Sheet with 200mm lapping (Overlapping Joints)- Rate is applicable only for laid
Plan Floor Area and no overlaps will be paid seperately- White colour LDPE sheet shall be considered.
ISOLATION JOINT FILLING WORK- Supplying and laying of Duro Board 25mm thk in position as per drawing & Filling
the Tioflex 600 PG size of filling 25mm x 20mm thk.( Applicable for external ramp & Staircase joint filling, around RCC
columns and pheripery wall work)(The Quoted shall be inculsive of deep cleaning by using mechanical equipments,
Soap oil, fixing of self drilling screw and disposal of concrete dust from site premises)
CONCRETING WORKS
Providing and laying machine batched and machine mixed reinforced cement concrete of M-25 grade with Minimum
Cement Content as per IS mix design with OPC cement. (With Flyash as per Design Mix shall be used as part
replacement of OPC Cement) using 20mm down-graded machine crushed stone aggregate, M sand/River sand as Fine
Aggregate, in footings, Pedestals, columns, Plinth beams, rafts, walls, and Slab (From foundation to FFL), With complete
finish and proper Curing, etc., as per the drawing and the directions of the Engineer-in-charge. (The cost of shuttering and
reinforcement steel will be measured separately.

In Footings/Foundations
In Plinth beams
In Columns & Pedestals
In Floor Concrete
Providing and laying machine batched and machine mixed reinforced cement concrete of M-25 grade with Minimum
Cement Content as per IS mix design with OPC cement. ( With Flyash as per Design Mix shall be used as part
replacement of OPC Cement) ABOVE FFL up to 4.5m height using 20 mm and downgraded machine crushed stone
aggregate, M sand/River sand as Fine Aggregate, in the superstructure in columns, lintels, beams, sunshades, slabs, etc.,
With proper curing and complete finish as per the drawing and the direction of the Engineer in charge. (The cost of
shuttering and reinforcement will be measured separately)
For Column & Pedestal
In Roof beam & Roof slab,Lintels & Sunshades
STEEL WORKS

FE500 - Supplying, fabricating, and tying in position at all levels of steel reinforcement for all RCC works including
cutting, bending, and binding with 18 gauge M.S.annealed binding wire or by welding if required, and rate-inclusive of
all lifting, leading & precast concrete cover blocks with ribs/PVC Cover blocks with complete finish as instructed by
Engineer In charge.
NOTE: Laps, Spacer bars, and Chairs will be measured for payments, and wastages not considered for payment.

TMT Fe-500 Steel reinforcement

Laying and tying in position at all levels & at placing locations of Welded Wire Fabric Mesh Reinforcement works
(WWF- TATA STEEL/Equivalent). The approx Size of the mesh is (6m x 2.45m). Rate to be inclusive of Unloading of
weld mesh and Placing the mesh nearby the Flooring Bay and also cost inclusive of precast concrete cover block for the
flooring work with the size of 75x75 mm with rib and Binding with 18 gauge M.S. annealed binding wire or by welding if
required, as per the drawing and instructions of engineer-in-charge.
Note : The weld mesh will be supplied by client.

FORMWORKS
Providing and fixing OF Good Quality Film Coated Plywood centering and shuttering as required in all types of
foundations, basement, and up to finished floor level in footings, columns, pedestals, beams, rafts, with necessary
strutting, bracing, propping, etc., and keeping the same in position during concreting and removing the same after a
specified period, etc. With a complete Finish. From foundation bottom level to Finished Floor Level(Maximum
repetitions of shuttering plywood shall be 5 repetitions only)
Note: FFL means floor finished level of Shop Floor
In PCC -Footing/Plinth beam
In Footings/Foundations
In Plinth beams
In Columns & Pedestals
Providing and fixing plywood or steel sheet centering and shuttering as required in the superstructure in R.C.C.
columns, beams, lintels, sunshades, slabs, etc., and keeping the same in position during concreting and removing the same
after a specified period, etc., with a complete finish. up to 4.50M height from the finished floor level (Maximum
repetitions of shuttering plywood shall be 5 repetitions only).
In Columns.
In Roof beam / Roof slab / Lintels & Sunshades
MASONRY / FINISHING WORKS
Providing and constructing cement concrete Fly ash brick masonry work Up to FFL levels in cement mortar 1:5 using
standard size of solid cement concrete blocks of thickness as given below, with minimum compressive strength of 5
N/Sq.mm. conforming to IS 2185 or equivalent BS and Fly ash conforming to IS: 3812 (Part III)-1966* may be used for part
replacement of fine aggregate up to a limit of 20 percent. as per the drawing.

Solid block wall of 200 mm thick (For Entrance steps)

Solid block wall of 300 mm thick
Providing and constructing Fly ash brick 230mm thick masonry work at all type of structure in cement mortar 1:5 by
using standard size of bricks of approved make with minimum crushing strength 9 N/mm2. including all scaffolding,
staging, striking off extra mortar, curing etc.The Flyash brick work to be done from above plinth to FFL etc. All complete
shall be done as per specification and laid as directed.
Providing and laying 150mm thick Fly ash brick Block masonry for the wall from FFL to 4.5m levels in Cement Mortar
1:4 with minimum crushing strength 5N/mm2 including all scaffolding, staging, striking off extra mortar, Pointing,
lifting, leading, and curing. Including placing M20 grade reinforced cement concrete with binders and 80mm thick
concrete using a coarse graded aggregate of 12mm and downsize, reinforced with 2 nos. of 8mm dia. Fe500 grade steel
(Single layer) and 6 mm dia. Mild steel stirrups at every 200mm c/c. The rate shall include the cost of reinforcements and
tying in position using binding wire made out of 18 gauge MS annealed, formwork, scaffolding, raking out, including all
materials, labor, etc. with the complete finish as per the instruction of the Engineer in charge.
Providing and laying Fly ash brick Masonry wall of 100 mm thick from FFL to 4.5m levels With C.M 1: 4 including all
scaffolding, staging, striking off extra mortar, Pointing, Lifting, leading, and curing. Including placing of M20 grade
reinforced cement concrete with binders and 80mm thick concrete using a coarse graded aggregate of 12 mm and
downsize, reinforced with 2 nos. of 8 mm dia. Fe 500 (single layer) and 6 mm dia. Mild steel stirrups at 200 mm c/c. The
rate shall include the cost of reinforcing steel and tying in position using binding wire made out of 18 gauge MS annealed,
formwork, scaffolding, raking out, including all materials, labor, etc. with the complete finish as per the instruction of the
Engineer in charge.

FALSE CEILING WORKS / TOILETS / OFFICES

Providing and fixing Armstrong or Equivalent using 12mm Grid sectionsfalse ceiling of size 24”x24” at all levels as shown
in the drwng. Rate shall be inclusive of providing the total system with installation etc.. The contractor has to maintain all
tiles in good order and before handing over the site.The rate inclusive of providing required GI frame with required
supports and accessories,etc,Complete finish.The rate shall include making cutouts for varies AC duct, cable tray, conduit
pipe, etc for specified size, for which no extra will be paid separately. Providing polyseal material to fill the gap between
duct or cable tray and partition board to make air tight. ( Plan area will measured and paid)

JOINERIES WORKS
Providing and fixing of factory made Sliding window (White Colour) complete, comprising uPVC multi-chambered frame
of size 67mm x 54mm having uPVC roller track on top and uPVC sash of size 60mm x 47mm. All corners of frame and
sash will be fusion welded and duly reinforced with G.I. section 1.2 mm. After placing 5mm float or prescribed glass in
the sash, uPVC glazing bead, interlock, EPDM gasket, brush will be provided including hardware, i.e., touch lock and
rollers & proper including hardware, i.e., touch lock and rollers & proper drainage system shall be provided. Window
will be fixed to the wall with 100mm long and 8mm dia. Fasteners and complete in all respect as per direction of Engineer-
In-Charge. The shutter section shall be made out of extruded rigid uPVC with internal side reinforced with provision of
5mm thick clear glass as per requirement

1200mm x 1500mm

Providing and fixing of factory made approved make, uPVC Louver window comprising of uPVC multi-chambered
frame of size 67 mm x 54 mm, duly reinforced with 1.2 mm thick G. I. Section. Both vertical sides of the frame, adjustable
louver with 4 mm frosted glass and having one lever to adjust the glass. Window will be fixed to the wall with 100mm
long and 8mm dia. Fasteners and complete in all respect as per direction of Engineer-In-Charge.

600mm x 600mm
Providing and fixing sintex door for openings of size 0.75m x 2.10m height the drawing with necessary fittings etc.
complete. (Toilet doors)
Providing and fixing 32 mm thk solid Wooden Door Shutters heavy quality door with frame and & Back side 2mm Thick
SS sheet confirming SS304 garde fixing upto 2.1m Height., including necessary SS Hardware, fixtures and fastenings as
specified, like hinges 4 nos per shutter, tower bolts 2 no, floor door stoppers 1 no, 2 handles per shutter (all hardware
shall be stainless steel) etc. complete as directed by Engineer In Charge.
Size of Doors shall be 1200m x 2100m
Providing and fixing Glazed aluminium door of size 1000 x 2100mm height with all the necessary fittings (hinges , tower
bolt, lock etc) . Complete including all tools and labours. As per the approved drawing.
FLOORING & FINISHING WORKS
Prepare the surfaces of levelling course / R.C. slab and lay vitrified ceramic tiles flooring of approved make and size and
laid over 20mm thick base mortar in c.m. 1:3, Riversand Fine Aggregate, including finishing the butt joints clean to given
lines and levels. Basic Rate - Rs. 60 per Sq.ft.
Prepare the surfaces of brick masonry and lay glazed tiles dado of approved make and size and laid over 20mm thick base
mortar in c.m. 1:3, Riversand Fine Aggregate, including finishing the butt joints clean to given lines and levels.Basic Rate
-Rs. 45 per Sq.ft.
Granite Counter -Providing and Laying of edge molding to 18 mm thick Granite stone counters, Vanities, etc., including
machine polishing to edge to give a high glass finish, etc. complete as per the design approved by the Engineerin-Charge.

Prepare the surfaces of all ceiling and sofits of R.C. Surfaces and plaster in c.m. 1:3, Riversand Fine Aggregate, 12mm thick
finished smooth with trowel and sponge including scaffolding, curing etc., complete at all levels
Prepare the surface of all Internal walls Plaster with cement mortar 1:5 (1 cement: 5 fine sand) of 12 mm thick including
GI mesh of nominal thickness at the junctions of masonry and concrete works to a width of 100 to 125mm including tying
in position with suitable clamps/screws, necessary hacking, staging,scaffolding and curing at all levels and elevations
etc.as complete with all respects complying with relevant standard specification, as directed. Before proceeding internal
wall plastering works contractor shall do packing of chiesled portitions filled with proper CM 1: 5 for the all MEP
services.

Prepare the surfaces of all external walls plaster in c.m. 1:4, by using a waterproofing compound of “CICO No.1 or
equivalent“ as per Manufacturer's Specification, Rivers sand/M sand as Fine Aggregate, 18mm thick finished smooth
with wood float, GI mesh of nominal thickness at the junctions of masonry and concrete works to a width of mesh 100 to
125mm including tying in position with suitable clamps/screws, necessary hacking, staging, scaffolding and curing at all
levels and elevations, etc. as complete with all respects complying with relevant standard specification, as directed.

PAINTING WORKS
Prepare the surfaces of the ceiling and R.C. surfaces and apply 3 coats of whitewash, curing, etc., complete. The height of
the ceiling From finished G.F to 4.5 m height.
Providing and applying 2 coats of Acrylic emulsion with low VOC content including one base coat of primer of approved
make and two or more coats of Acrylic emulsion as per manufacturer specifications and make and sample mock-up to be
approved by the Engineer In Charge. The rate shall be inclusive of necessary scaffolding and staging etc. With the
complete finish, all respects comply with relevant standard specifications, as directed by the Engineer in charge. ( Internal
walls).
Note: The colour has to be finalized by the client
From finished G.F to 4.5m height
Providing and applying 2 coats of weatherproof Acrylic emulsion paint with low VOC content including one base coat of
primer and two or more coats of Exterior Emulsion paint as per manufacturer specifications and making sample mock-up
to be approved by the Engineer In Charge. The rate shall be inclusive of necessary scaffolding or staging etc. with the
complete finish, in all respects complying with relevant standard specifications, as directed by the Engineer in charge.
( External walls)
Note: The colour has to be finalized by the client
From finished G.F to 4.5m height
TOTAL
ADD: GST @ 18%
GRAND TOTAL
Note:River sand shall be used as a fine aggregate for all civil works
D, CHENNAI
T CUTTACK-ODISHA

RATE AMOUNT
QTY UNIT REMARKS
IN Rs. IN Rs.

172.00 CuM. 245 42,140

43.00 CuM. 315 13,545

20.00 CuM. 500 10,000

20.00 CuM. 750 15,000

36.00 CuM 1,250 45,000

18.00 CuM. 2,850 51,300

119.00 SqM 110 13,090

119.00 SqM 110 13,090

46.00 RMT 1,500 69,000

12.00 CuM. 6,850 82,200

12.00 CuM. 6,850 82,200
5.00 CuM. 6,850 34,250
18.00 CuM. 6,850 123,300

13.00 CuM. 7,250 94,250

29.00 CuM. 7,250 210,250

6.00 M.T. 77,000 462,000

 1.00 M.T. 13,500 13,500

20.00 Sqm 700 14,000

47.00 Sqm 750 35,250
102.00 Sqm 750 76,500
122.00 Sqm 750 91,500

48.00 Sqm 850 40,800

248.00 Sqm 850 210,800

4.00 Cum 7,250 29,000

QRO Cum 7,250 _

23.00 Cum 7,250 166,750

160.00 SqM. 1,250 200,000

38.00 SqM. 1,150 43,700

QRO SqM. 2,600 _

11.00 SqM. 12,500 137,500

3.00 SqM. 12,500 37,500

QRO Nos 8,500 _

QRO Nos 20,000 _

1.00 Nos 18,500 18,500

119.00 SqM. 1,850 220,150

198.00 SqM. 1,750 346,500

 5.00 SqM. 10,000 50,000

QRO SqM. 450 _

345.00 SqM. 500 172,500

175.00 SqM. 600 105,000

119.00 SqM. 100 11,900

345.00 SqM. 300 103,500

175.00 SqM. 400 70,000

3,643,965
655,914
4,299,879
 TVS INDUSTRIAL AND LOGISTICS PARKS PRIVATE LIMITED, CHENNAI
Project : CONSTRUCTION OF LIGHT MANUFACTURING FACILITY AT CUTTACK-ODISHA
BILL OF QUANTITIES - COLLECTION TANK
RATE AMOUNT
SL.NO DESCRIPTION OF WORKS QTY UNIT REMARKS
IN Rs. IN Rs.
A EXCAVATION WORKS
Excavation in all types of soil and soft disintegrated rock but excluding laterite and hard rock.
At all types of foundation structures, Rafts and walls, etc. to required levels, grades, and
dressing with the complete finish and required equipment as per the specifications and
directions of the Engineer in charge, Including subsoil backfilling around the foundations and
Walls with selected excavated earth in 200mm thick each layer with watering, consolidating
1
and compaction of 200mm thick of (Layer by layer) etc. wherever necessary disposal of the
surplus excavated material shall be dumped site. The Quoted rate shall be inclusive of
complete tools, Equipment, and labor with the complete finish. as per the instruction of the
Engineer in charge.

a) Upto 2.00m below existing ground level. 101.00 Cum 245 24,745
b) From 2.00m to 4.00m below existing ground level. 31.00 Cum 315 9,765
Excavation in all types of Laterite rock but excluding hard rock.At all types of foundation
structures, plinth beams, etc. to required levels, grades, and dressing with the complete finish
as per specifications and directions of the Engineer in-charge, Including subsoil backfilling
(Available soil) around foundations and plinth beam with selected excavated earth in 200mm
each layer with proper watering and consolidation, compaction of 200mm thickness (Layer by
2
layer) etc. wherever necessary disposal of the surplus excavated material shall be dumped site.
The Quoted rate shall be inclusive of complete tools, equipment, and labour with a complete
finish. as per the instruction of the Engineer in charge.

a) Upto 2.00m below existing ground level. 20.00 Cum 500 10,000
b) From 2.00m to 4.00m below existing ground level. 10.00 Cum 750 7,500
B CONCRETING WORKS
Providing and laying plain cement concrete of mix 1:4:8 in all foundations, Rafts and beams,
etc. using 20mm graded stone aggregate, M sand/River sand as Fine Aggregate, compacting,
1 4.00 Cum 5,900 23,600
and curing. with the complete finish as per the drawing. (With Flyash asper Design mix shall
be used as part replacement of OPC Cement)
Providing and laying reinforced cement concrete of M-25 grade with a Minimum Cement
Content of 320 Kgs of pure cement /CuM using 20 mm and down-graded machine crushed
stone aggregate, M sand/River sand as a Fine Aggregate by used for the rafts, walls, and slab
2 concrete, etc. The top of the slab level shall be considered as per the drawing with proper
curing, and complete finish as per the instructions of the engineer in charge, etc.,(The cost of
shuttering and reinforcement will be measured separately).

a) For Raft 9.00 Cum 6,850 61,650

b) For side walls & baffles 19.00 Cum 6,850 130,150
c) For cover slab 3.50 Cum 6,850 23,975
C STEEL WORKS
FE500 - Supplying, fabricating, and tying in position at all levels of steel reinforcement for all
RCC works including cutting, bending, and binding with 18 gauge M.S.annealed binding
wire or by welding if required, and rate-inclusive of all lifting, leading & precast concrete
1 cover blocks with ribs/PVC Cover blocks with complete finish as instructed by Engineer In 3.00 Ton 77,000 231,000
charge.
NOTE: Laps, Spacer bars, and Chairs will be measured for payments, and wastages not
considered for payment.

D FORMWORKS

Providing and fixing wrought timber/steel sheet/plywood centering and shuttering as

required in all types of foundations, basement, side walls, and up to finished collection
tank slab level as per drawing in rafts, Side walls, and slab with necessary strutting, bracing,
1
propping, etc., and keeping the same in position during concreting and removing the same
after a specified period, etc. With complete finish as per the instruction of the Engineer in
charge.
a) For Raft 13.00 Sqm 750 9,750
b) For side walls & baffles 150.00 Sqm 750 112,500
c) For cover slab 27.00 Sqm 750 20,250
E FINISHING / WATER PROOFING WORKS

TVSI Page 22 of 28
 TVS INDUSTRIAL AND LOGISTICS PARKS PRIVATE LIMITED, CHENNAI
Project : CONSTRUCTION OF LIGHT MANUFACTURING FACILITY AT CUTTACK-ODISHA
BILL OF QUANTITIES - COLLECTION TANK
Prepare the surfaces of all external of R.C. surfaces of walls etc. and plaster in c.m.1:3, 12mm
1 thick mixed with water proofing compound of approved quality at all heights finished QRO Sqm 600 _
smooth with trowel and sponge including scaffolding, curing etc., complete.
2 Pressure grouting / Water proof coating

Providing chemical injection treatment in the form of pressure grouting to the cold/starter
joints of the walls structure by injecting cement slurry mixed with grout admixture Conbex
100 with Nitobond SBR @ 3 ltrs. per bag of cement, nonshrink polymer grouting compound to
the required consistency through the pre-fixed GI nozzles in the 18mm dia. holes drilled in a
grid pattern at a spacing not exceeding 1.00m x 1.00m grid on the top of base slab including
drilling holes using pneumatic hammer drilling machine, fixing of GI nozzles with Renderoc
Plug and final cutting the projected nozzles and sealing off the GI nozzles after the injection
75.00 Sqm 1,900 142,500
operation with Renderoc Plug, non shrink rapid setting mortar compound, finishing, curing
etc. as per manufacturers specification and as directed. The rate to include the cost of all
materials, labor equipment employed, etc., complete.
Providing, supplying, mixing, and applying two coats of ready-to-use component acrylic
polymer modified cement-based, flexible, waterproofing BRUSHBOND RFX to a thickness of
2mm over the surface of operation including preparation of surface, dewatering, finishing,
curing, etc., complete as per manufacturer's specification and as directed.

Providing and fixing in position 600mm x 600 mm heavy duty RCC manhole cover and frame
3 4.00 Nos 10,500 42,000
including grouting, curing etc. complete
Providing and fixing 50 NB, 3000mm long 6kg PVC. vent pipe with wire gauge including
4 12.00 Rmt 1,500 18,000
grouting the joint etc. complete
5 Providing & Fixing in position of PVC Rungs Including Necessary consumables etc 18.00 Nos 2,000 36,000
Providing and Fixinig of 150mm wide PVC Water Stopper including necessary consumbles.,
6 66.00 Rmt 1,500 99,000
etc
TOTAL 1,002,385.00
ADD: GST @ 18% 180,429.30
GRAND TOTAL 1,182,814.30
Note:River sand shall be used as a fine aggregate for all civil works

TVSI Page 23 of 28
 TVS INDUSTRIAL AND LOGISTICS PARKS PRIVATE LIMITED, CHENNAI
Project: CONSTRUCTION OF LIGHT MANUFACTURING FACILITY AT CUTTACK-ODISHA
BILL OF QUANTITIES - SANITARY FITTING & PLUMBING WORK
RATE AMOUNT
SL.NO DESCRIPTION OF WORKS QTY UNIT REMARKS
IN Rs. IN Rs.
A SANITARYWARE & CP FITTINGS

Providing and fixng European Water Closet suite comprising of: A.Floor mounted
European water closet having S or P trap,
B.Low level flushing cisten with all internal fittings resting on the closet.
C.Seat and cover with hinges to suite the above closet.
1 D.Rag bolt and nuts to fix the closet 28.00 Set 25,500 714,000
E.15mm CP Inlet angle stop cock - 2Nos with 15mm x 450mm CP tube, nuts and
washers etc., including making necessary holes and redoing the disturbed portions
complete. Flusing tank should have "DUAL" system (2+4Liters capacity)
WHITE SUITE:

Providing and fixing Indian Water Closet suite comprisng of:

A. Indian wate clsoet ORISSA PAN squatting type with raised foot rest and adjustable
trap embedding closet and trap in cement concret.
B. Low level PVC flushing cistern with all internal fittings and PVC flush bend.
C. Rigid PVC flush pipe 50mm dia with required PVC elbows concealed in wall upto
2 3.00 Set 11,500 34,500
floor level.
D. 15mm dia CP Inlet angle stop cock with 15mm x 450mm CP tube,nuts and washers
etc.,inclduing making good the disturbed portions complete.Flusing tank should have
"DUAL" system (2+4Liters capacity)
WHITE SUITE:

Providing and fixing Urinal suite comprisig of:

A. Flat back Large Urinal with concealed trap.
B. 32mm CP dome type waste coupling
C. 15mm CP inlet angle stop cock with 15mm x 450mm CP tube and nuts and washers.
D. 15mm CP sreader with 15mm CP Nipple.
E. 50mm rigid PVC waste pipe with required PVC elbows concealed in wall upto floor
3 16.00 Set 17,500 280,000
level
F. Bottle trap.
G. Rag bolt and nuts etc., including making good the disturbed portions complete. The
type of CP fitting shall be Auto release press type
H.providing & fixing of Ceramic partition
WHITE SUITE:

Providing and fixing Lav.suite comprising of:

A. Wash hand basin of size 550mmx400mm
B. 15mm CP Piller cock high neck (Auto Push type & flow shall be foam flow)
C. 32mm CP waste coupling
D. 32mm CP Bottle trap
4 E. 15mm CP Inlet angle stop cock with 15mm x 450mm CP tube and nuts and washers. 18.00 Set 12,500 225,000
F. 40mm rigid PVC waste pipe with required PVC elbow concealed in wall upto floor
level.
G. Rag bolt and nuts including 'L' type brackets etc.,including making good the
disturbed portions complete.
WHITE SUITE:

Providing and fixing highly double side polished granite urinal partition of size 3'-6"
5 x 2'-0 x 20mm jet black/ruby red with edges moulded and polished and embedding 16.00 Each 8,500 136,000
the same in wall as per the drawing and grouting with cement mortor complete.

Providing and fixing CP Health faucet with 15mm CP 2 - in - 1 Bib cock with CP
6 28.00 set 2,900 81,200
flange,1mtr long flexible tube including with bracket complete.
Providing and fixing SS robe hook of size 9" long with hooks and fixing with
7 31.00 each 2,850 88,350
necessary barass screws.
Providing and fixing CP towel rod of size 24"x20mm with end brackets and fixing
8 28.00 each 2,900 81,200
with necessary brass screws complete.
Providing and fixing CP.Bib tap long body (With foam flow) 15mm size with CP
9 28.00 each 3,000 84,000
flange complete.
Providing and fixing C.P.Toilet pater holder with C.P.roller and necessary bracket and
10 28.00 each 2,850 79,800
screws complete.
11 Providing and fixing CP Soap dish with bracket. 18.00 each 2,900 52,200
 Providing and fixing Wall Mixer with connect for head Shower Arrangement with
12 Connecting Legs, Wall Flanges & Wall Bracket for head Shower with nexessary screws 2.00 each 8,500 17,000
complete as per drawing.
Providing and fixing best quality Mirror of size 24'' x 18" with water proof ply and CP
13 18.00 each 3,750 67,500
cup type screws complete.
Providing and fixing PVC door for openings of size 0.75m x 2.1m height the drawing
14
with necessary fittings etc. complete. (Toilet doors)
a. Size of Doors shall be 0.75m x 2.10m 30.00 Nos 6,500 195,000
Providing and fixing 44 mm thick solid Wooden Door Shutters heavy quality door
with frame and & Back side 2mm Thick SS sheet confirming SS304 garde fixing up to
2.1m Height., including necessary SS Hardware, ffasteners and fixtures(4" hinges- 4nos
15 per shutter, tower bolts 1 no, door stopper 1 no, 2 handles per shutter (all hardware
shall be stainless steel) etc. complete as directed by Engineer In Charge.

a. Size of Doors shall be 1.0m x 2.10m 7.00 Nos 18,500 129,500

ALUMINIUM DOOR SHUTTER :

Providing and fixing of aluminum doors and frame, with extruded built-up
tubular sections/ appropriate Z sections and other sections of approved make
conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia
and size, including necessary filling up the gaps at junctions, i.e. at top. bottom
and sides with required EPDM rubber/ neoprene gasket etc. Aluminum
16 4.00 Nos 10,000 40,000
sections shall be smooth, rust-free, straight, mitered, and jointed mechanically
wherever required including all accessories, door handle, hinges, door
stopper, tower bolt, door closer, cleat angle, Aluminium snap beading for
glazing /paneling, C.P. brass/stainless steel screws, all complete finish as per
the architectural drawings and the directions of Engineer-in-charge.
The Size of the Aluminum Door shall be 1.00 x 2.10m

B INTERNAL SOIL AND WASTE PIPES

Providing and fixing rigid PVC soil and waste pipe with required PVC accessories
such as PVC tee, elbows, reducers, offset, couplers, etc., including cutting and jointing
1 with best quality PVC solvent and embedding the same in cement concrete wherever
found necessary and fixing the open lines with special type fabricated brackets and
redoing the disturbed portions completely.
A. 160mm dia x 6Kg.Cm2 QRO rmtr 2,000 _
B. 110mm dia x 6Kg.Cm2 80.00 rmtr 1,800 144,000
C. 75mm dia x 6Kg.cm2 70.00 rmtr 950 66,500
D. 63mm dia x 6Kg.Cm2 40.00 rmtr 650 26,000
E. 50mm dia x 6Kg.Cm2 50.00 rmtr 600 30,000
F. 40mm dia x 6Kg.Cm2 20.00 rmtr 500 10,000
Providing and fixing rigid PVC Nahini trap/PVC elbow/tee embedded in cement
2 concrete and masonry curb all round plastering and on top fitted with SS square 64.00 each 1,950 124,800
openable grating complete.
3 As detailed above but with 110mm dia outlet 'P' trap for Urinals. 16.00 each 3,500 56,000

4 Providing and fixing of clean outs with plug Finished to Floor levels etc., complete. -

A. 160mm dia 2.00 each 3,500 7,000

A. 110mm dia 2.00 each 2,500 5,000
A. 75mm dia 2.00 each 2,000 4,000
C INTERNAL WATER SUPPLY (DWS & FWS)
Providing and fixing rigid CPVC water supply pipes with SDR-11 heavy quality with
required CPVC fittings such as tee, elbow, reducers, unions, couplers, etc., including
chasing the wall/floor and concealing the pipes wherever found necessary, laying the
1 pipes below the ground level(including earthwork excavation and refilling) and fixing
the open lines with fabricated MS brackets, etc., complete including redoing the
disturbed portions neatly. and rate inclusive of water flow meter wherever required as
per site requirement
A.50mm dia CPVC GRADE PIPE - heavy quality 80.00 rmtr 800 64,000
B. 40mm dia CPVC pipes x heavy quality 70.00 rmtr 700 49,000
C. 32mm dia CPVC pipes x heavy quality 60.00 rmtr 600 36,000
E. 25mm dia CPVC pipes x heavy quality 60.00 rmtr 500 30,000
F. 20mm dia CPVC pipes x heavy quality 30.00 rmtr 400 12,000

Digital Water flow meter with cover for flush water connection wherever required as
per site requirement and the cost inclusive of supply and fixing and make shall be
2
referred as per our Design specification and it shall be approved make. ALSTER MAG
FLOW 650 ELECTRO-MAGNETIC FLOW METER Basic Model Rubber Lined

A.50mm 8.00 Nos 4,000 32,000

B.40mm 10.00 Nos 3,000 30,000
D EXTERNAL WATER SUPPLY ARRANGEMENTS:
(WELL TO SUMP,SUMP TO DELIVERY LINES & OHT)

Providing and fixing rigid CPVC pipes heavy quality SDR 11 pipe with requiredCPVC
fittings such as tee,elbow,reducers,unions and nipple etc.,including cutting,jointing
and chasses in wall and floor and concealing the pipes wherever found necessary and
1
jointing the pipes with best quality solvent CPVC cement etc.,including earth work
excavation and refilling for the pipes laid under ground and for the open lines fixing
with necessary
A.100mm dia CPVC-SDR 11 PIPE - heavy quality QRO Rmtr 1,850 _
B.80mm dia CPVC-SDR 11 PIPE - heavy quality 200.00 Rmtr 1,225 245,000
C.65mm dia CPVC-SDR 11 PIPE - heavy quality 140.00 Rmtr 1,000 140,000
E.50mm dia CPVC-SD 11 GRADE PIPE - heavy quality 130.00 Rmtr 775 100,750
F.40mm dia do 125.00 Rmtr 700 87,500
G.32mm dia do 60.00 Rmtr 600 36,000
H.25mm dia do 20.00 Rmtr 500 10,000

(Note :For CPVC -SDR 11 pipes all the specials are CPVC and CPVC brass fittings)

Providing and fixing GM wheel valve full way/UPVC ball valve with required fittings
2
complete.
A.50mm dia Leader Class I-ISI/CPVC BALL VALVE 10.00 Unit 4,000 40,000
B.40mm dia do 10.00 Unit 3,000 30,000
C.32mm dia do 5.00 Unit 2,000 10,000
Providing and fixing Butterfly Valves of Approved make with required fittings
3
complete.
A. 100mm dia do 2.00 Unit 7,500 15,000
B. 80mm dia do QRO Unit 6,500 _
C. 65mm dia do 2.00 Unit 5,500 11,000
D. 50mm dia do 2.00 Unit 4,000 8,000
4 Providing and fixing NRV of approved make fittings complete.
A. 60 mm dia do 1.00 Unit 8,000 8,000
B. 50mm dia do 1.00 Unit 7,000 7,000
C. 40mm dia do 1.00 Unit 5,000 5,000
D. 32mm dia do 1.00 Unit 4,000 4,000
E PUMPS FOR WATER SUPPLY & SEWAGE LINE

For domestic water and flush water distribution supplying, Installation and
commissioning as per the below mentioned specification:
Multi E 2 x CRE 15-3 -3Kw_60Hz_IE5 / Flow 18 m3/hr, Head 40 m
1) Pump -CI / AISI 304 (Base / Impeller) Qty 2 Nos (1W+1S)_Motor Mounted
VFD_IE5
2) Panel with Multi E
3) Suction Manifold – 1Set -MS
4) Suction Butterfly valve - 1set
5) Delivery Manifold – 1Set -MS
1 6) Delivery Butterfly valve -1 set QRO Set 400,000 _
7) Common Base frame -MS-Fab -1 Set -
8) Pr. Transmitter – 1no
9) Pr.Gauge – 1no
Note:
# All the components and pumps will be supplied as per Grundfos standard
# We considered MS Skid _PN16
# Motor Protection we considered IP 65
Note:# All the components and pumps will be supplied as per Grundfos
GT-U-500 PN10 G11/4 V (coated flange) Pressure tank - 01 nos

Providing, fixing & commisioning 5HP TEXMO or equivalent make (as directed by
the architect) mono block pumpset three phase with auto float sensor suction and
delivery of 50mm x 45mm with required G.I. fittings/CPVC including construction of
masonry platform with required foundation bolt and nuts etc., complete but Inclusive
of wiring and starter with LED Indicators, auto float sensors.(ONE STANDBY PUMP
2 2.00 Set 380,000 760,000
AND BOTH PUPMS INTERCONNECTED WITH VALVES) The starter panel shall
be IP 65 protection with outdoor encloser to be fixed at external area. The cable from
starer panel to the Main panel shall be around 20m.

Pump lowering and connecting main supply service including fitting & fixing etc., &
complete commissioning supply & fixing of 50mm dia G.I class B pipe including
3 required fittings etc. 10.00 Rmt 3,400 34,000

Supply and Fixing of Raw Sewage Transfer Pump

Model No. : LGP1335/1335F, Make : Lubi
Head : 30m Head, Flow Rate : 2 Cum / Hr.
Type : Sewage Submercible Cutter Type
4 Qty : 1 Working + 1 Stand By 3.00 Nos 330,000 990,000
Control Panel : Twin Pump Control Panel Digital DOL controller
Cost is inclusive of all necessary fittings , Cable, Values, Consumables etc

Supply and Fixing of Treated Water pump

Model No . : CM 3-5 , Make : Lubi
Head : 40m Head , Flow Rate : 2 Cum / Hr.
Type Sewage Submercible Cutter Type
5 Qty : 1 Working + 1 Stand By QRO Nos 400,000 _
Control Panel : IP 41
Cost should be inclusive of all necessary fittings , values, pipes for 15m length od
required delivery head of pump etc
F EXTERNAL DRAINAGE ARRANGEMENTS:
Providing and laying rigid PVC drainage pipes of 6Kg.cm2 with required PVC fittings
such as tee, elbow,coupler etc.,including cutting and jointing with best quality PVC
1
solvent cement and resting on the firm ground including earth work excavation
refilling and consolidation complete.
A. 250mm dia do QRO Rmtr 3,000 _
B. 200mm dia do QRO Rmtr 2,500 _
C. 160mm dia do 200.00 Rmtr 1,950 390,000
D. 110mm dia do 320.00 Rmtr 1,450 464,000
E. 75mm dia do 80.00 Rmtr 1,000 80,000
F. 63mm dia do QRO Rmtr 700 _
G. 50mm dia do 80.00 Rmtr 500 40,000
Providing,fixing in position, jointing and testing RCC hume pipe NP-3 class with
Screw joint in including complete layining, with engineer incharge instructions.. (The
2 Quoted rate shall be inclusive of excavation & Laying of PCC bed )

A. 450mm dia do 60.00 Rmtr 3,000 180,000

B. 300mm dia do QRO Rmtr 2,500 _
G CONSTRUCTION INSPECTION CHAMBER
size 600mm x 600mm internally with flyash brick and of varying depths not exceeding
1.0m deep, with 100mm PCC 1:4:8, and 150mm thick 1:2:4 raft slab as subgrades and
brick masonry chambers of varying thickness in CM 1:3 and plaster for walls in CM 1:3
1 4.00 each 15,000 60,000
benching and channeling in PCC 1:2:4 complete. The quoted rate shall be inclusive of
Excavation & refilling.

size 750mm x 750mm internally with flyash brick work and of varying depths not
exceeding 1.0m deep, with 100mm PCC 1:4:8,and 150mm thick 1:2:4 raft slab as sub
2 grades and brick masonry chambers of varying thickness in CM 1:3 and plaster for 2.00 each 20,000 40,000
walls in CM 1:3 benching and chanelling in PCC 1:2:4 complete.The quoted rate shall
be inclusive of Excavation & refilling.

As detailed above but size of Chamber is 900x900 depth 1.01m to 1.50m (Considered
3 230mm thick wall entire depth) The quoted rate shall be inclusive of Excavation & 6.00 each 25,000 150,000
refilling.
As detailed above but size of Chamber is 1200x900 depth 1.51m to 2.50m (Consider
wall thickness from bottom level to 1.5m 450mm thickness and 1.5m to top level
4 230mm wall Thickness) 2.00 each 35,000 70,000
The quoted rate shall be inclusive of Excavation & refilling.

5 Providing and Fixing of of PVC Rungs including necessary consumbles .,etc 30.00 nos 1,500 45,000
Providing and fixing square type SFRC manhole cover of size 600mm x 600mm
6 medium quality 50kg wt.with cement concrete on top of the manhole chamber 6.00 each 7,500 45,000
complete. Inclusive of one coat of primer and 2coats of synthetic enamel paint
Providing and fixing square type SFRC manhole cover of size 900mm x 900mm
7 medium quality 50kg wt.with cement concrete on top of the manhole chamber 6.00 each 9,500 57,000
complete. Inclusive of one coat of primer and 2coats of synthetic enamel paint
Providing and fixing SW gully trap of size 6" x 4" 110mm dia outlet vitreous trap
chambers with brick work over bed of cement concrete and plastering the walls inside
8 and outside and on top fitted with CI frame and cover of size 300 x 300mm /7kg wt., 4.00 each 5,000 20,000
complete.
I BORE WELL WORKS
Groundwater Investigation for all Sinking points for finding borewells at the entire
1 1.00 Lum 25,000 25,000
park level by using the magnetic method or satellite instrument
Sinking machine well of 6.5" dia up to a depth of 600 feet (Casing pipe-7'' up to 100 Ft)
and fixing 5 HP 40 stage 3 phase - Texmo borewell submersible pump or equivalent
2 and delivery size 1.5"dia, total head of 600feet, and supply and fixing UPVC pipe - 2.00 Unit 375,000 750,000
Ashirvad/equivalent upto 575ft with nylon rope with including valve, adaptor,
coupling and other required accessories.

3 sinkingwell water sample test 2.00 Lum 10,000 20,000

4 Providing and fixing CPVC half turn full way valve with required fittings complete

a) For 25 mm pipe line 2.00 Each 500 1,000

b) For 40mm pipe line 2.00 Each 1,000 2,000
c) For 50mm pipe line 2.00 Each 1,500 3,000
Supplying & Fixing of control panel comprising of Ammeter, Voltmeter, single phase
preventer, indicator lamp, starter realtor, Automatic switch control with auto float
5 controller, 4Sqmm cable of required length from above well to control panel complete 2.00 Lum 50,000 100,000
and 4Cx16Sq.mm cable of required length from starter panel (IP66) to Main raw power
panel.
Total 8,114,800
ADD: GST @ 18% 1,460,664
GRAND TOTAL 9,575,464