Professional Documents
Culture Documents
Operators Manual: Micro-Adjustor
Operators Manual: Micro-Adjustor
with
MICRO-ADJUSTOR
Operators
Manual
HTC-800
Contractor Version
HTC-900
PRECI
SI
1''
16
12 1 ''
8
BU
- IN
LT
Commercial Version
1''
64
RO
R
O
1''
32
A DJUS
TM
Purchasers Record
Model Number:
Purchased From:
Address:
Purchase Date:
This information becomes your permanent record of a valuable purchase.
It should be filled in promptly then kept in a safe place along with your
purchase receipt to be referred to as necessary for insurance purposes or
when corresponding with HTC Products. Fill out and return the enclosed
warranty card.
Table of Contents
The following general safety rules are supplied as an aid for the safe use of
many products. This is NOT a complete list of all possible safety rules. Safe use
of a product includes but should NOT be limited to the following safety rules.
Safety Rules................................3-4
Applications....................................5
Adjustments/Set-up ....................5-6
Parts...............................................7
Warranty Information......................8
TM
16. Remove adjusting keys and wrenches. Form the habit of checking
to see that keys and adjusting wrenches are removed from the tool
before turning the tool on.
17. Cutting tool exposure. Adjust the tool for minimum exposure of
cutting tool necessary to perform the operation.
18. Direction of feed. Feed work into a blade or cutting tool against the
direction of rotation of the blade or cutting tool only.
19. Dont overreach. Keep proper footing and balance at all times.
20. Never stand on tool. Serious injury could occur if the tool is tipped
or if the cutting tool is accidentally contacted.
21. Avoid accidental starting. Make sure switch is in the OFF position
before plugging in tool. Do not carry a plugged in tool with finger on
switch.
22. Inspect workpiece. Always inspect workpiece to make sure there
arent any nails or foreign objects in the part of the workpiece to be
worked on.
23. Plan ahead. Mentally plan ahead to protect your eyes, hands, body,
face and hearing. Do layout, assembly, setup work, material
handling, and planning before using tool.
24. Disconnect tools. Always turn tool OFF and disconnect the cord
from the power source before tool is serviced or when installing or
removing accessories such as blades, bits, or cutters etc.
25. Maintain tools with care. Inspect tool before each use. It is
recommended that the general condition of any tool be examined
before it is used.
26. Check damaged parts. Before further use of the tool, a guard or
other part that is damaged should be carefully checked to ensure
that it will operate properly and perform its intended function.
27. Ground all tools. Make sure wiring codes and recommended
electrical connections are followed and that tool is properly
grounded.
28. Outdoor use extension cords. When tool is used outdoors, use
only extension cords marked suitable for use with outdoor
appliances store indoors when not in use.
29. Ground Fault Circuit Interrupters - (GFCIs) provide additional
means to reduce serious electrical shock while using a power tool.
Applications
The HTC Multi-Fence System is designed to fit current table saw fence
rails from the following manufacturers fence systems: Jet Exacta, Powermatic
Accu-Fence, Biesemeyer Commercial. Compatability with other similar rail
systems is possible, and can be determined by measuring the distance from
the table surface to the top of the rail tube as shown in Figure 1. For
compatability, this measurement must be 5/8'' for the HTC-800, and 13/16'' for
the HTC-900.
Saw
Table
Fence
Tube
Adjustments / Set-up
Figure 1
Before using you new Multi-Fence System, a few adjustments will need to
be made to insure proper operation. Follow the simple steps detailed below.
Square the fence face to the saw table
1. Lightly engage the main fence lock. Simply snugging the fence to the
rail at this point is fine. The nylon set screws shown in Figure 2
should be resting on the fence rail.
Nylon Set
Screw
2. Place a square on the table against the fence face. The fence should
be 90 to the table. Figure 3.
Nylon Set
Screw
3. If adjustment is necessary, unlock the fence and adjust the nylon set
screws until the fence is 90 to the table.
4. Re-engage the main fence lock and check the setting.
Figure 2
Leveling
1. Lightly engage the main fence lock. Sight along the bottom edge of
the fence face and compare the distance between the table surface
and the bottom of the fence face. This should be a consistant 1/32''
front to back. Figure 4.
2. Should adjustment be necessary, unlock the main fence lock.
3. Raise or lower the nylon set screws shown in Figure 2. Rotate both
the set screws the same amount to prevent disturbing the square
adjustments made in the previous step.
Figure 3
1/32''
Saw Table
Figure 4
1. Place the fence next to the outside edge of the right miter slot, and
engage the main fence lock. Figure 5.
2. Before making any adjustments, note the location of the fence face in
relation to the miter slot. It should be parallel with the miter slot.
3. Main fence lock should engage fully onto flat machined in the fence
lock cam. This should engage securely but not be overly tight. Figure 6.
4. Should adjustment for clamp pressure or parallelism be required.
Remove the fence and turn over. Figure 7.
5. Adjust one or both screws shown in Figure 7 until clamp pressure
and parallelism with miter slot is satisfactory.
Note: Tighten both the set screws (clockwise) to increase clamp pressure.
Tighten one side in, the other side out, to adjust for parallelism.
5
Figure 5
Cursor Adjustment/Setting
1. Raise the saw blade above the table top. Be sure power has been
disconnected.
2. Unlock the fence and slide it to approximately 4'' from the blade.
Engage the main fence lock.
3. Measure the distance between the blade and the inside of the fence
face.
4. Adjust the cursor to read the distance just measured and tighten the
cursor assembly to the fence.
5. Make a test cut to confirm the setting.
Figure 6
Note: This adjustment must be checked whenever a different blade is
installed.
Set
Screw
Set Screw Adjust
one IN, the other OUT
Micro-Adjust Use
1. Position fence to approximate location for the cut being planned.
Main fence lock 3 can be very lightly engaged to square the fence.
Figure 8.
2. Secure the Micro-Adjust quick lock lever 1 . This lever is spring
loaded for speed and ease of use.
Figure 7
Figure 8
Lock
DO NOT
OVER
TIGHTEN
Unlock
To reinstall, simply align the key hole shaped fasteners in the fence
face, over the screws in the fence tube, and tap into the locked position
from the infeed end.
Figure 9
Install
Remove
Figure 10
Parts
Qty.
Fence Body
5085
Wear Pad
A109
Dust Cap
G511
Stud
C104
Side Face
2833
Mounting Clip
F102
Screw
D316
5/16 18 x 3/8" Adjustment Screw C225
1/2 13 x 1/2" Adjustment Screw
A107
Cursor
A306
Pan Head Screw 10 32 x 1/4"
D209
Micro Adjust Knob
G303
Spacer
2852
Pivot Bolt
2811
Nut
2812
3/8" Spring Washer
C422
3/8" 16 Nut L.H.
C419
Spring
2834
1/4" 20 Nyloc Nut
D912
Clamp
2818
Bolt 1/4" 20 x 1-1/2"
D133
Lock Handle with Cam
5085B
Micro Adjust Lock Lever
C103
Wear Plate
2837
Micro Adjust Saddle
5086A
10 32 x 1/4" Retainer Bolt
D207
Friction Spacer (Saddle)
A110
1/2" x 7/8" Wear Pad
A111
1
1
2
8
2
8
16
2
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
Description
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Description
Part #
Qty.
Fence Body
Wear Pad
Dust Cap
Stud
Side Face
Mounting Clip
Screw
5/16" 18 x 3/8" Adjustment Screw
1/2" 13 x 1/2" Adjustment Screw
Cursor Bracket
Cursor
Pan Head Screw
Flat Head Screw
Washer
10 32 Keps Nut
Micro Adjust Knob
Spacer
Pivot Bolt
Nut
3/8" Spring Washer
3/8" 16 Nut L.H.
Spring
1/4" 20 Nyloc Nut
Clamp
Bolt 1/4" 20 x 1-1/2"
Lock Handle with Cam
Micro Adjust Lock Lever
Wear Plate
Micro Adjust Saddle
10 32 x 1/4" Retainer Bolt
Friction Spacer (Saddle)
1/2" x 7/8" Wear Pad
5080
A108
G510
C104
2816
F102
D316
C225
A107
A305
A304
D209
D208
D211
D210
G303
2852
2811
2812
C422
C419
2834
D912
2089
D133
5080B
C103
2837
5084A
D207
A110
A111
1
1
2
8
2
8
16
2
2
1
1
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2