Series 90 Axial Piston Pumps: Size 75cc

Parts Manual
Series 90 Axial Piston Pumps

Size 75cc
www.danfoss.com
Parts Manual
Series 90 75cc Axial Piston Pump
Revision history Table of revisions
Date Changed Rev
July 2020 Changed document number from 'AX00000091' to 'AX152886482206' and updated part numbers 0501
2 | © Danfoss | July 2020 AX152886482206en-0501

Parts Manual
Contents
General information
Service Parts Identification............................................................................................................................................................7
Nameplate...........................................................................................................................................................................................7
Date code............................................................................................................................................................................................ 8
About service bulletins...................................................................................................................................................................8
Procedure to identify a part..........................................................................................................................................................8
Regional part numbers............................................................................................................................................................. 8
Example of a part identification (S90 75cc)....................................................................................................................... 8
Adobe Acrobat 2-page viewing.................................................................................................................................................. 9
Order code........................................................................................................................................................................................10
Common parts and special hardware
S90P 75cc common parts............................................................................................................................................................11
Special hardware EAB-EBA......................................................................................................................................................... 15
Special hardware EBC, EBE..........................................................................................................................................................17
Special hardware EDC-EDI.......................................................................................................................................................... 19
Special hardware EEB, EEG..........................................................................................................................................................21
Special hardware EEH...................................................................................................................................................................23
Special hardware EFC-EFL...........................................................................................................................................................27
Special hardware EFP....................................................................................................................................................................29
Special hardware EFR................................................................................................................................................................... 33
Special hardware EHA-EKB......................................................................................................................................................... 37
Special hardware ELA................................................................................................................................................................... 39
Special hardware ELB....................................................................................................................................................................43
Special hardware ELC................................................................................................................................................................... 47
Special hardware FAA-FAK......................................................................................................................................................... 51
Special hardware FAL, FAN.........................................................................................................................................................53
Special hardware FAP-FAU......................................................................................................................................................... 55
Special hardware FAX, FAY.........................................................................................................................................................57
Special hardware FAZ-FBG......................................................................................................................................................... 59
Special hardware FCF, FHP......................................................................................................................................................... 61
Special hardware GAA-GBT........................................................................................................................................................ 63
Special hardware GBU..................................................................................................................................................................65
Special hardware GBX-GCP........................................................................................................................................................ 69
Special hardware GCR-GCU........................................................................................................................................................71
Special hardware GDE-GFP.........................................................................................................................................................73
Special hardware GFS-GFZ......................................................................................................................................................... 75
Special hardware GHT-GMA.......................................................................................................................................................77
Special hardware GMC................................................................................................................................................................. 79
Special hardware GMD.................................................................................................................................................................83
Special hardware GME................................................................................................................................................................. 87
Special hardware GTA-PEA.........................................................................................................................................................91
Special hardware PEB-PGB......................................................................................................................................................... 93
Displacement
Displacement limitation 1-4.......................................................................................................................................................95
Displacement limitation 7...........................................................................................................................................................97
Displacement limitation 8, B...................................................................................................................................................... 99
Displacement limitation D....................................................................................................................................................... 101
Displacement limitation F........................................................................................................................................................ 103
Displacement limitation H....................................................................................................................................................... 105
Displacement limitation L........................................................................................................................................................ 107
Displacement limitation............................................................................................................................................................109
End cap
End cap H-6R................................................................................................................................................................................. 111
End cap 60-67............................................................................................................................................................................... 113
End cap 6U, 6W.............................................................................................................................................................................115
End cap 1-81..................................................................................................................................................................................117
End cap 82, 8W............................................................................................................................................................................. 119
End cap 80-8V (built in Germany)..........................................................................................................................................121
© Danfoss | July 2020 AX152886482206en-0501 | 3

Parts Manual
Contents
Charging system
Charging system C-F.................................................................................................................................................................. 123
Charging system L, N..................................................................................................................................................................125
Charging system S, Y.................................................................................................................................................................. 127
Auxiliary mounting
Auxiliary mounting AB and AC............................................................................................................................................... 129
Aux mounting AH-BA.................................................................................................................................................................131
Aux mounting BB-V.................................................................................................................................................................... 133
Aux mounting BD........................................................................................................................................................................ 135
Aux mounting BE, BF..................................................................................................................................................................137
Aux mounting BH-BP................................................................................................................................................................. 139
Aux mounting BR.........................................................................................................................................................................141
Aux mounting BT-CK..................................................................................................................................................................143
Aux mounting CK........................................................................................................................................................................ 145
Auxiliary mounting CP, CR....................................................................................................................................................... 147
Aux mounting CT-CV..................................................................................................................................................................149
Aux mounting CW.......................................................................................................................................................................151
Aux mounting CX-NN................................................................................................................................................................ 153
Charge pressure setting
Charge pressure setting............................................................................................................................................................ 155
Shaft
Shaft C6-SA.................................................................................................................................................................................... 157
Shaft G2, J8, K2............................................................................................................................................................................. 159
Shaft T1-TJ......................................................................................................................................................................................161
Control
Control CA-DD.............................................................................................................................................................................. 163
Control EA, EG...............................................................................................................................................................................165
Control EP, EX................................................................................................................................................................................167
Control FA-FD............................................................................................................................................................................... 169
Control FG, FH...............................................................................................................................................................................171
Control FK-FN................................................................................................................................................................................173
Control HF-HS............................................................................................................................................................................... 175
Control HU-JC............................................................................................................................................................................... 177
Control K0-K7................................................................................................................................................................................ 179
Control KA-KC............................................................................................................................................................................... 181
Control KD-KH...............................................................................................................................................................................183
Control KK-KP................................................................................................................................................................................185
Control KT.......................................................................................................................................................................................187
Control KY, LB................................................................................................................................................................................189
Control LC, LE................................................................................................................................................................................ 191
Control LG, LK............................................................................................................................................................................... 193
Control LL, LN................................................................................................................................................................................195
Control LS, LT................................................................................................................................................................................ 197
Control M1, M2............................................................................................................................................................................. 199
Control M3..................................................................................................................................................................................... 201
Control M7, M8............................................................................................................................................................................. 203
Control MA, MB............................................................................................................................................................................ 205
Control MC, MD............................................................................................................................................................................207
Control ME, MG............................................................................................................................................................................ 209
Control MH, MJ............................................................................................................................................................................. 211
Control MK, ML............................................................................................................................................................................. 213
Control MN.....................................................................................................................................................................................215
Control MR, MS............................................................................................................................................................................. 217
Control MT, MV.............................................................................................................................................................................219
Control MW....................................................................................................................................................................................221
Control MX, MY.............................................................................................................................................................................223
Control NA, NC..............................................................................................................................................................................225

Parts Manual
Contents
Control NE...................................................................................................................................................................................... 227

Control NU..................................................................................................................................................................................... 229
Control PA, PB............................................................................................................................................................................... 231
Control PE.......................................................................................................................................................................................233
Control PF, PG............................................................................................................................................................................... 235
Control PH, PJ................................................................................................................................................................................237
Control RR, RS................................................................................................................................................................................239
Control RU...................................................................................................................................................................................... 241
Control SA, SB, SD, SE................................................................................................................................................................. 243
Control SC.......................................................................................................................................................................................245
Filtration
Filtration 3-J...................................................................................................................................................................................247
Filtration L, P..................................................................................................................................................................................249
Filtration R-X..................................................................................................................................................................................251
High pressure protection
High pressure regulation 1-7...................................................................................................................................................253
High pressure regulation A-F.................................................................................................................................................. 255
High pressure regulation G-M.................................................................................................................................................257
High pressure regulation N, P................................................................................................................................................. 259
High pressure regulation R, S.................................................................................................................................................. 261
High pressure regulation U, W................................................................................................................................................263
High pressure regulation X, Y..................................................................................................................................................265
Orifice
Orifice 01-24.................................................................................................................................................................................. 267
Orifice 25-34.................................................................................................................................................................................. 271
Orifice 48-49.................................................................................................................................................................................. 275
Orifice 50-76.................................................................................................................................................................................. 277
Orifice 78-A7..................................................................................................................................................................................281
Orifice A8-C4..................................................................................................................................................................................285
Orifice C5-G8................................................................................................................................................................................. 289
Orifice G8-P1..................................................................................................................................................................................293
Orifice Z1, Z3................................................................................................................................................................................. 297
overhaul seal kit
Seal kit..............................................................................................................................................................................................299
Service bulletin
SB-1988-009...................................................................................................................................................................................300
SB-1988-016...................................................................................................................................................................................302
SB-1988-023...................................................................................................................................................................................304
SB-1989-002...................................................................................................................................................................................306
SB-1989-003...................................................................................................................................................................................306
SB-1989-006...................................................................................................................................................................................308
SB-1989-023...................................................................................................................................................................................310
SB-1992-003...................................................................................................................................................................................312
SB-1992-011...................................................................................................................................................................................314
SB-1993-001...................................................................................................................................................................................315
SB-1993-015...................................................................................................................................................................................318
SB-1994-017...................................................................................................................................................................................320
SB-1994-018...................................................................................................................................................................................321
SB-1994-36..................................................................................................................................................................................... 323
SB-1995-003...................................................................................................................................................................................324
SB-1995-012...................................................................................................................................................................................325
SB-1995-025...................................................................................................................................................................................327
SB-1996-009...................................................................................................................................................................................329
SB-1998-066...................................................................................................................................................................................330
SB-1998-041...................................................................................................................................................................................332
SB-1998-073...................................................................................................................................................................................334

Parts Manual
Contents
SB-1999-009...................................................................................................................................................................................336
SB-1999-019...................................................................................................................................................................................338
SB-1999-041...................................................................................................................................................................................339
SB-1999-065...................................................................................................................................................................................341
SB-2000-022...................................................................................................................................................................................343
SB-2000-041...................................................................................................................................................................................345
SB-2002-050...................................................................................................................................................................................346
SB-2004-012...................................................................................................................................................................................347
SB-2005-007...................................................................................................................................................................................348
SB-2005-011...................................................................................................................................................................................350
SB-2007-027...................................................................................................................................................................................351
SB-2007-051...................................................................................................................................................................................353
SB-2007-055...................................................................................................................................................................................355
SB-2009-073...................................................................................................................................................................................357
SB-2013-011...................................................................................................................................................................................359
SB-2015-005...................................................................................................................................................................................360
SB-2017-033...................................................................................................................................................................................361

Parts Manual
General information
Service Parts Identification

The following information and procedure is used to identify the module group, item number,
manufacture date, part number, and part name of the parts included in the .
The parts listed include all parts which may be used when performing either “Minor Repairs”, “Major
Repairs” or “Conversions” on the .
Nameplate
Each unit will have a nameplate affixed to the housing. The nameplate will include the following
information:
Model Code
The Danfoss model code completely defines the specific unit and must be used when ordering parts to
service this product.
Model Number
The Danfoss model number is used by the factory in manufacturing. On repeat orders, a complete unit
can be ordered by the model number.
Serial Number
The Danfoss serial number is used to identify the manufacture date and the unit sequence in the build.
The serial number is also used to identify the units warranty time period.
The letter code indicates the location of original manufacture (assembly).
The first number (2 digits) indicates the year of manufacture. The second number (2 digits) indicates the
calendar week of manufacture.
The third number (5 digits) is a sequential number used to identify a specific unit.
Model No./Ident No. 9521216

Model Code 90 L 075 EP 1
NN 60 S 3 S1 D
03 GBA 35 35 24
Serial No. A-01-26-23456
Made in U. S. A.

Parts Manual
General information
Date code
The date code is defined as the year and week of manufacture. The same item number may list more than
one part number. This indicates that there is more than one configuration for that item number. You will
see that there are different date codes for the different part numbers. Find the date code of your unit
from the nameplate to determine which service part number you need to order.
Example: The service part desired is item G30

Order Code Item Date Begin Date End Part Number Part Name Qty. per
Model/Kit
80 G30 89-17 8000243 End cap gasket 1
G30 89-16 8000151 End cap gasket 1
(SB-1995-006)
All units using this order code with a date code prior to 89-17 must use part number “8000151.” All units
with a date code of 89-17 and newer must use part number “8000243.”
About service bulletins

A Service Bulletin Number (SB-_ _ _ _ - _ _ _) may follow the “Part Name” of the part you desire. You must
read that Service Bulletin prior to ordering that part. The information contained in these Service Bulletins,
as of the print date of this bulletin, are included at the end of this manual. Service Bulletins contain more
detailed information such as interchangeability, what additional parts are involved, etc. It is suggested
that you add additional Service Bulletins to this manual as you receive them.
Procedure to identify a part

The modular design of this product results in a simplified service parts list and part number identification
procedure.
The same item numbers are used for same part names on all units within a product type. A part number
that has another number following it in parentheses is done to make this a world wide manual.
Regional part numbers

Some part numbers are region specific and should be ordered accordingly.
As an example, the part number (example: 314583 (9008000-0118) will be used. The first number is sold
in Germany. The number in parentheses is sold in the United States. Customers would order
9008000-0118 if ordering the part in the United States.
Example of a part identification (S90 75cc)

The nameplate on a Series 90 pump has an Order Code of 90L075 EP 1 NN 60 S 3 S1 D 03 GBA 35 35 24.
Use the following procedures to determine the part number of the drive shaft used on this pump.
1. Referring to the input shaft module in the Order Code, the input shaft option for this pump is
identified by the code “S1. (90L075 EP 1 NN 60 S 3 S1 D 03 GBA 35 35 24).
2. Referring to the Service Parts List, find the shaft group. Next find the order code that relates to this
unit, which is “S1”. The shaft is found to be item L100 and part number 8100264.

Parts Manual
General information
Adobe Acrobat 2-page viewing

While viewing manual in Adobe Acrobat, the following settings need to be applied to ensure proper
page display.
1. Select “View” → “Page Display” → “Two Page View”
2. Select “View” → “Page Display” → “Show Cover Page in Two Page View”

Parts Manual
General information
Order code
Series Displacement
M P J G N F L H T W Y Z K
9 0 L 0 7 5 E P 1 CD 6 0 S 3 S 1 D 0 3 G B A 3 5 3 5 2 4
Rotation
Control
Pressure regulation
Auxiliary mounting pad
End cap
Filtration
Displacement limitation
Shaft
Charging system
Control orifice
Special hardware features
High pressure setting port A
High pressure setting port B

Parts Manual
S90P 75cc common parts
Parts configuration
B80 L60 L70
*B90
B70
B72 L40
*B90
B82
L20
B10 L50
*L25
QD50 L10
D55
F20 D65
M14 B50
D10
D75
D70 E30
B50
E20
D85 E22
QB30
D80 E80
E24
D50 *E50
E90
QD50 E10
D55
D65
F20
M14
D10
E70 *E60
*E40
D75
D95 D70 D60 E30
D85 E80
D80 E24 E20
D50
Swashplate Leveler design

design prior 99-28 thru 06-26
to 05-48
* Included in base pump seal kit Q210

Parts Manual
Common parts
Item Date Begin Date End Part Number Part Name Qty. per
Model/Kit
B10 05-49 11001300 Housing (SB-2005-007 on page 348) 1
B50 87-02 9004800-3708 Pin 2
B70 87-02 140644 (9005110-5600) Plug assembly 1
B72 87-02 140644 (9005110-5600) Plug assembly 1
B80 87-02 664524 (9005110-9000) Plug assembly 1
B82 92-19 140644 (9005110-5600) Plug assembly (SB-1992-003 on page 312) 1
B90 87-02 9803390 Control filter screen 3
D10 05-49 519046 Servo arm (SB-2005-007 on page 348) 1
D10 88-16 05-48 8100499 Servo arm assembly (SB-1993-015 on page 318) 1
D50 05-49 11000688 Swashplate (SB-2005-007 on page 348) 1
D50 88-16 05-48 8100367 Swashplate 1
D55 05-49 519150 Screw (SB-2005-007 on page 348) 1
D55 87-02 05-48 666032 (9007276-0107) Screw 1
D60 87-02 05-48 8800669 Swashplate guide 1
D65 87-02 9007375-0044 Screw (SB-1992-011 on page 314) 1
D70 87-02 9009625-0146 Washer 1
D75 87-02 9004875-0098 Spiral head pin 1
D80 87-02 693929 (8100506) Cage locator link (SB-1994-017 on page 320) 1
D85 01-26 8801235 Pin (SB-2004-012 on page 347) 1
D85 87-02 01-25 8801135 Pin (SB-1998-018) 1
D95 87-02 05-48 8100035 Spring (SB-2005-007 on page 348) 1
E10 05-49 11001286 Side cover (SB-2005-007 on page 348) 1
E10 95-50 05-48 501572 Side cover (SB-1995-025 on page 327) 1
E20 98-14 11042018 Leveler (SB-1999-009 on page 336) 1
E22 06-27 517935 Spring seat 2
E22 99-28 06-26 none
E22 98-14 99-27 517935 Spring seat (SB-1999-009 on page 336) 2
E24 92-06 8801225 Shim (SB-2000-041 on page 345) 2
E30 99-28 11056531 Guide post (SB-2009-073 on page 357) 2
E30 95-50 99-27 8000510 Guide post (SB-1999-009 on page 336) 2
E30 87-02 95-49 8510098 Side cover kit (SB-1995-025 on page 327) 1
E40 87-02 505412 (9003509-0008) Seal nut 2
E50 87-02 517377 O-ring 1
E60 87-02 517228 (5000206) Screw (SB-1994-018 on page 321) 6
E70 87-02 664524 (9005110-9000) Plug assembly 1
E80 87-02 334987 (11062691) Spring 2
E90 95-50 513888 Insert assembly (SB-1995-025 on page 327 & 1
SB-1999-041 on page 339)
F20 88-16 11116313 Slider block (SB-1988-009 on page 300 & 1
SB-2015-005 on page 360)
Part numbers continue to the next 2 pages.

Parts Manual
Parts configuration
B80 L60 L70
*B90
B70
B72 L40
*B90
B82
L20
B10 L50
*L25
QD50 L10
D55
F20 D65
M14 B50
D10
D75
D70 E30
B50
E20
D85 E22
QB30
D80 E80
E24
D50 *E50
E90
QD50 E10
D55
D65
F20
M14
D10
E70 *E60
*E40
D75
D95 D70 D60 E30
D85 E80
D80 E24 E20
D50
Swashplate Leveler design

design prior 99-28 thru 06-26
to 05-48

Parts Manual
Common parts
Model/Kit
L10 87-02 5000505 Roller bearing 1
L20 87-02 9006300-0156 Retaining ring 1
L25 87-02 519671 Seal carrier assembly (SB-2005-007 on page 348) 1
L40 87-02 519666 Lip seal (SB-2005-007 on page 348) 1
L50 87-02 684621 (9004104-1530) O-ring 1
L60 87-02 516767 Retainer plate 1
L70 87-02 041160 (9007314-0605) Screw 3
QB30 87-02 05-48 676841 (8700048) Cradle bearing assembly (SB-2005-007 on page 1
348)
QB30 05-49 11131108 Cradle bearing assembly (SB-2005-007 on page 1
348)
QD50 05-49 8100984 Swashplate assembly (SB-2005-007 on page 348) 1
QD50 88-16 05-48 8100376 Swashplate assembly (SB-1988-009 on page 300) 1

Parts Manual
S90P 75cc special hardware EAB-EBA

Parts configuration
(EAB, EAS, EAV & EBE)

*QB83
B83
QC04
C20
C30
C40
C06 E82
C50 E82
*C70
C80
(EAC, EBA & EBC)

*QB83
B83
QC04
C20
C30
C40
C06
C50
*C70
C80
Generic speed sensors shown.

Parts Manual
Common parts
Model/Kit
C20 87-02 708230 Piston assembly (SB-1988-023 on page 304) 9
C30 87-02 11067350 Slipper guide 1
C40 88-22 334391 (8100294) Slipper guide bearing (SB-1988-016 on page 302) 2
C50 88-22 11065865 Spacer (SB-1988-016 on page 302 & SB-1998-041 4
on page 332)
C65 88-22 98-47 Obsolete Washer (SB-1988-016 on page 302 & SB-1998-041 4
on page 332)
C70 88-22 314419 (9007276-0114) Screw (SB-1988-016 on page 302 & SB-1998-041 4
on page 332)
QB83 98-14 085043 (9004201-3700) O-ring 1
Order code: EAB

B83 98-14 KPPG12508 Speed sensor 1
C06 98-14 11094260 (11011714) Cylinder block assembly, with speed ring 1
C80 98-14 518008 Valve plate 1
E82 98-14 11062703 Spring 2
QC04 98-14 8510366 Cylinder block kit, with speed ring 1
Order code: EAC

C80 98-14 518805 Valve plate 1
Order code: EAS

C80 98-14 518008 Valve plate 1
E82 98-14 360842 Spring 2
Order code: EAV

B83 06-12 12-35 11046858 Speed sensor 1
C06 06-12 12-35 11094260 (11011714) Cylinder block assembly, with speed ring 1
C80 06-12 12-35 518008 Valve plate 1
E82 06-12 12-35 11062703 Spring 2
QC04 06-12 12-35 8510366 Cylinder block kit, with speed ring 1
Order code: EBA

C80 04-26 518924 Valve plate 1

Parts Manual
S90P 75cc special hardware EBC, EBE

Parts configuration
(EAB, EAS, EAV & EBE)

*QB83
B83
QC04
C20
C30
C40
C06 E82
C50 E82
*C70
C80
(EAC, EBA & EBC)

*QB83
B83
QC04
C20
C30
C40
C06
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
on page 332)
on page 332)
on page 332)
QB83 98-14 085043 (9004201-3700) O-ring 1
Order code: EBC

C80 04-26 518805 Valve plate 1
Order code: EBE

C80 94-30 518805 Valve plate 1
E82 98-14 11062703 Spring 2

Parts Manual
S90P 75cc special hardware EDC-EDI

Parts configuration
(EDC)
*QB83
B83
QC04
C20
C30
C40
C06 E82
C50 E82
*C70
(EEB & EEG)

C80
B83
(EDF, EDH & EDI)

*QB83
B83
QC04
C20
C30
C40
C06
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
on page 332)
on page 332)
on page 332)
QB83 98-14 085043 (9004201-3700) O-ring 1
Order code: EDC

C80 94-34 518925 Valve plate, CW 1
C80 94-34 518926 Valve plate, CCW 1
E82 94-34 11062703 Spring 2
Order code: EDF

B83 94-34 12-35 11046858 Speed sensor 1
C80 97-14 12-35 518008 Valve plate 1
Order code: EDH

B83 99-17 12-36 KPPG15408 Speed sensor 1
C80 99-17 12-36 518007 Valve plate 1
Order code: EDI

C80 00-17 12-36 518925 Valve plate, CW 1
C80 00-17 12-36 518926 Valve plate, CCW 1

Parts Manual
S90P 75cc special hardware EEB, EEG

Parts configuration
(EDC)
*QB83
B83
QC04
C20
C30
C40
C06 E82
C50 E82
*C70
(EEB & EEG)

C80
B83
(EDF, EDH & EDI)

*QB83
B83
QC04
C20
C30
C40
C06
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
on page 332)
on page 332)
on page 332)
QB83 98-14 085043 (9004201-3700) O-ring 1
Order code: EEB

B83 99-17 140644 (9005110-5600) Plug assembly 1
C80 99-17 518008 Valve plate 1
Order code: EEG

B83 00-17 140644 (9005110-5600) Plug assembly 1
C80 00-17 518925 Valve plate, CW 1

Parts Manual
S90P 75cc special hardware EEH

Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94
L50
B83 *L25
L10
QD50 D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C06
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: EEH

Model/Kit
B50 05-20 12-36 9004800-3708 Pin 2
B70 05-20 12-36 140644 Plug assembly 1
B72 05-20 12-36 140644 Plug assembly 1
B80 05-20 12-36 664524 (9005110-9000) Plug assembly 1
B83 05-20 12-36 140644 Plug assembly 1
B84 05-20 12-36 11040532 Plug assembly 1
B92 05-20 12-36 11040532 Plug assembly 1
B94 05-20 12-36 11040532 Plug assembly 1
B100 05-20 12-36 11117294 Housing assembly 1
C20 05-20 12-36 708230 Piston assembly 9
C30 05-20 12-36 11067350 Slipper guide 1
C40 05-20 12-36 334391 (8100294) Slipper guide bearing 2
C50 05-20 12-36 11065865 Spacer 4
C70 05-20 12-36 314419 (9007276-0114) Screw 4
C80 05-20 12-36 518008 Valve plate 1
D10 05-20 12-36 519046 Servo arm 1
D50 05-20 12-36 11104315 Swashplate 1
D55 05-20 12-36 519150 Screw 1
D70 05-20 12-36 9009625-0146 Washer 1
D75 05-20 12-36 9004875-0098 Spiral head pin 1
D80 05-20 12-36 693929 (8100506) Cage locator link 1
D86 05-20 12-36 9004800-1908 Pin 1
D87 05-20 12-36 11040532 Plug assembly 1
E10 05-20 12-36 11001286 Side cover 1
E20 05-20 12-36 11042018 Leveler 1
E22 05-20 12-36 517935 Spring seat 2
E24 05-20 12-36 8801225 Shim 2
E30 05-20 12-36 11056531 Guide post 2
E40 05-20 12-36 505412 (9003509-0008) Seal nut 2
E50 05-20 12-36 517377 O-ring 1
E60 05-20 12-36 517228 (5000206) Screw 6
E70 05-20 12-36 664524 (9005110-9000) Plug assembly 1
E80 05-20 12-36 334987 Spring 2
E90 05-20 12-36 513888 Insert assembly 1
F20 05-20 12-36 11116313 Slider block (SB-1988-009 on page 300 & 1
SB-2015-005 on page 360)

Parts Manual
Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94
L50
B83 *L25
L10
QD50 D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C06
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: EEH

Model/Kit
L10 05-20 12-36 5000505 Roller bearing 1
L20 05-20 12-36 9006300-0156 Retaining ring 1
L25 05-20 12-36 519671 Seal carrier assembly 1
L40 05-20 12-36 519666 Lip seal (SB-2005-007 on page 348) 1
L50 05-20 12-36 684621 (9004104-1530) O-ring 1
L60 05-20 12-36 516767 Retainer plate 1
L70 05-20 12-36 041160 (9007314-0605) Screw 3
QB30 05-20 12-36 11131108 Cradle bearing assembly 1
QD50 05-20 12-36 11192313 Swashplate assembly (SB-2017-033 on page 361) 1

Parts Manual
S90P 75cc special hardware EFC-EFL

Parts configuration
(EFD & EFG)
*QB83
B83
QC04
C20
C30
C40
C06 E82
C50 E82
*C70
(EFC, EFI & EFL)

C80
*QB83
B83
QC04
C20
C30
C40
C06
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
on page 332)
on page 332)
on page 332)
QB83 98-14 085043 (9004201-3700) O-ring 1
Order code: EFC

C80 94-34 518805 Valve plate 1
QC04 94-34 8510366 Cylinder block kit, with speed ring
Order code: EFD

C80 04-49 12-36 518008 Valve plate 1
E82 04-49 12-36 360842 Spring 2
QC04 94-34 12-36 8510366 Cylinder block kit, with speed ring
Order code: EFG

C80 04-49 12-36 518925 Valve plate, CW 1
E82 04-49 12-36 360842 Spring 2
Order code: EFI

C80 04-49 518925 Valve plate, CW 1
QC04 94-34 8510366 Cylinder block kit, with speed ring
Order code: EFL

C80 04-49 12-36 518007 Valve plate 1

Parts Manual
S90P 75cc special hardware EFP

Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*QB83 *L25
B83
L10
QD50 D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C06
C50 E90
E10
*C70
C80 E70 *E60

*E40
Generic speed sensor shown.

Parts Manual
Order code: EFP

Model/Kit
B50 05-34 9004800-3708 Pin 2
B70 05-34 140644 Plug assembly 1
B80 05-34 664524 (9005110-9000) Plug assembly 1
B83 05-34 KPPG156 Speed sensor assembly 1
B84 05-34 11040532 Plug assembly 1
B92 05-34 11040532 Plug assembly 1
B94 05-34 11040532 Plug assembly 1
B100 05-34 11117294 Housing assembly 1
C20 05-34 708230 Piston assembly 9
C30 05-34 11067350 Slipper guide 1
C40 05-34 334391 (8100294) Slipper guide bearing 2
C50 05-34 11065865 Spacer 4
C70 05-34 314419 (9007276-0114) Screw 4
C80 05-34 518925 Valve plate, CW 1
D10 05-34 519046 Servo arm 1
D50 05-34 11104315 Swashplate 1
D55 05-34 519150 Screw 1
D70 05-34 9009625-0146 Washer 1
D75 05-34 9004875-0098 Spiral head pin 1
D80 05-34 693929 (8100506) Cage locator link 1
D86 05-34 9004800-1908 Pin 1
D87 05-34 11040532 Plug assembly 1
E10 05-34 11001286 Side cover 1
E20 05-34 11042018 Leveler 1
E22 05-34 517935 Spring seat 2
E24 05-34 8801225 Shim 2
E30 05-34 11056531 Guide post 2
E40 05-34 505412 (9003509-0008) Seal nut 2
E50 05-34 517377 O-ring 1
E60 05-34 517228 (5000206) Screw 6
E70 05-34 664524 (9005110-9000) Plug assembly 1
E80 05-34 334987 Spring 2
E90 05-34 513888 Insert assembly 1
F20 05-34 11116313 Slider block (SB-2015-005 on page 360) 1

Parts Manual
Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*QB83 *L25
B83
L10
QD50 D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C06
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: EFP

Model/Kit
L20 05-34 9006300-0156 Retaining ring 1
L25 05-34 519671 Seal carrier assembly 1
L50 05-34 684621 (9004104-1530) O-ring 1
L70 05-34 041160 (9007314-0605) Screw 3
QB30 05-34 11131108 Cradle bearing assembly 1
QB83 05-34 085043 (9004201-3700) O-ring 1

Parts Manual
S90P 75cc special hardware EFR

Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*QB83 *L25
B83
L10
QD50 D55
D65
F20 QB30 B50 B84
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E22 E20
E82
QC04 C20 E80
E24
C30 *E50
C40
C06
E90
C50 E10
*C70
E70 *E60
C80 *E40

Parts Manual
Order code: EFR

Model/Kit
B50 06-18 9004800-3708 Pin 2
B80 06-18 664524 (9005110-9000) Plug assembly 1
B84 06-18 11040532 Plug assembly 1
B92 06-18 11040532 Plug assembly 1
B94 06-18 11040532 Plug assembly 1
C30 06-18 11067350 Slipper guide 1
C50 06-18 11065865 Spacer 4
C70 06-18 314419 (9007276-0114) Screw 4
C80 06-18 518008 Valve plate 1
D10 06-18 519046 Servo arm 1
D50 06-18 11104315 Swashplate 1
D55 06-18 519150 Screw 1
D70 06-18 9009625-0146 Washer 1
D75 06-18 9004875-0098 Spiral head pin 1
D86 06-18 9004800-1908 Pin 1
D87 06-18 11040532 Plug assembly 1
E10 06-18 11001286 Side cover 1
E20 06-18 11042018 Leveler 1
E22 06-18 517935 Spring seat 2
E24 06-18 8801225 Shim 2
E30 06-18 11056531 Guide post 2
E40 06-18 505412 (9003509-0008) Seal nut 2
E50 06-18 517377 O-ring 1
E60 06-18 517228 (5000206) Screw 6
E70 06-18 664524 (9005110-9000) Plug assembly 1
E80 06-18 334987 Spring 2
E82 06-18 360842 Spring 2
F20 06-18 11116313 Slider block (SB-2015-005 on page 360) 1

Parts Manual
Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*QB83 *L25
B83
L10
QD50 D55
D65
F20 QB30 B50 B84
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E22 E20
E82
QC04 C20 E80
E24
C30 *E50
C40
C06
E90
C50 E10
*C70
E70 *E60
C80 *E40

Parts Manual
Order code: EFR

Model/Kit
L20 06-18 9006300-0156 Retaining ring 1
L50 06-18 684621 (9004104-1530) O-ring 1
L70 06-18 041160 (9007314-0605) Screw 3
QB83 06-18 085043 (9004201-3700) O-ring 1

Parts Manual
S90P 75cc special hardware EAA-EKB

Parts configuration
*QB83
B83
QC04
C20
C30
C40
C06 E82
C50 E82
*C70
C80
*QB83
B83
QC04
C20
C30
C40
C06
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
QB83 98-14 085043 (9004201-3700) O-ring 1
Order code: EHA

C80 00-42 518805 Valve plate 1
Order code: EKA

C80 99-31 518805 Valve plate 1
Order code: EKB

C80 01-13 12-36 518925 Valve plate, CW 1
E82 01-13 12-36 360842 Spring 2

Parts Manual
S90P 75cc special hardware ELA

Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*QB83 *L25
B83
L10
QD50 D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C06
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: ELA

Model/Kit
B50 01-03 9004800-3708 Pin 2
B80 01-03 664524 (9005110-9000) Plug assembly 1
B84 01-03 11040532 Plug assembly 1
B92 01-03 11040532 Plug assembly 1
B94 01-03 11040532 Plug assembly 1
C30 01-03 11067350 Slipper guide 1
C50 01-03 11065865 Spacer 4
C70 01-03 314419 (9007276-0114) Screw 4
C80 01-03 518008 Valve plate 1
D10 01-03 519046 Servo arm 1
D50 01-03 11104315 Swashplate 1
D55 01-03 519150 Screw 1
D70 01-03 9009625-0146 Washer 1
D75 01-03 9004875-0098 Spiral head pin 1
D86 01-03 9004800-1908 Pin 1
D87 01-03 11040532 Plug assembly 1
E10 01-03 11001286 Side cover 1
E20 01-03 11042018 Leveler 1
E22 01-03 517935 Spring seat 2
E24 01-03 8801225 Shim 2
E30 01-03 11056531 Guide post 2
E40 01-03 505412 (9003509-0008) Seal nut 2
E50 01-03 517377 O-ring 1
E60 01-03 517228 (5000206) Screw 6
E70 01-03 664524 (9005110-9000) Plug assembly 1
E80 01-03 334987 Spring 2
F20 01-03 11116313 Slider block 1

Parts Manual
Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*QB83 *L25
B83
L10
QD50 D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C06
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: ELA

Model/Kit
L20 01-03 9006300-0156 Retaining ring 1
L50 01-03 684621 (9004104-1530) O-ring 1
L70 01-03 041160 (9007314-0605) Screw 3
QB83 01-03 085043 (9004201-3700) O-ring 1

Parts Manual
S90P 75cc special hardware ELB

Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*QB83 *L25
B83
L10
QD50 D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C06
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: ELB

Model/Kit
B50 04-03 9004800-3708 Pin 2
B80 04-03 664524 (9005110-9000) Plug assembly 1
B84 04-03 11040532 Plug assembly 1
B92 04-03 11040532 Plug assembly 1
B94 04-03 11040532 Plug assembly 1
C30 04-03 11067350 Slipper guide 1
C50 04-03 11065865 Spacer 4
C70 04-03 314419 (9007276-0114) Screw 4
C80 04-03 518925 Valve plate, CW 1
D10 04-03 519046 Servo arm 1
D50 04-03 11104315 Swashplate 1
D55 04-03 519150 Screw 1
D70 04-03 9009625-0146 Washer 1
D75 04-03 9004875-0098 Spiral head pin 1
D86 04-03 9004800-1908 Pin 1
D87 04-03 11040532 Plug assembly 1
E10 04-03 11001286 Side cover 1
E20 04-03 11042018 Leveler 1
E22 04-03 517935 Spring seat 2
E24 04-03 8801225 Shim 2
E30 04-03 11056531 Guide post 2
E40 04-03 505412 (9003509-0008) Seal nut 2
E50 04-03 517377 O-ring 1
E60 04-03 517228 (5000206) Screw 6
E70 04-03 664524 (9005110-9000) Plug assembly 1
E80 04-03 334987 Spring 2
F20 04-03 11116313 Slider block 1

Parts Manual
Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*QB83 *L25
B83
L10
QD50 D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C06
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: ELB

Model/Kit
L20 04-03 9006300-0156 Retaining ring 1
L50 04-03 684621 (9004104-1530) O-ring 1
L70 04-03 041160 (9007314-0605) Screw 3
QB83 04-03 085043 (9004201-3700) O-ring 1

Parts Manual
S90P 75cc special hardware ELC

Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*QB83 *L25
B83
L10
QD50 D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C06
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: ELC

Model/Kit
B50 04-18 9004800-3708 Pin 2
B80 04-18 664524 (9005110-9000) Plug assembly 1
B84 04-18 11040532 Plug assembly 1
B92 04-18 11040532 Plug assembly 1
B94 04-18 11040532 Plug assembly 1
C30 04-18 11067350 Slipper guide 1
C50 04-18 11065865 Spacer 4
C70 04-18 314419 (9007276-0114) Screw 4
C80 04-18 518925 Valve plate, CW 1
D10 04-18 519046 Servo arm 1
D50 04-18 11104315 Swashplate 1
D55 04-18 519150 Screw 1
D70 04-18 9009625-0146 Washer 1
D75 04-18 9004875-0098 Spiral head pin 1
D86 04-18 9004800-1908 Pin 1
D87 04-18 11040532 Plug assembly 1
E10 04-18 11001286 Side cover 1
E20 04-18 11042018 Leveler 1
E22 04-18 517935 Spring seat 2
E24 04-18 8801225 Shim 2
E30 04-18 11056531 Guide post 2
E40 04-18 505412 (9003509-0008) Seal nut 2
E50 04-18 517377 O-ring 1
E60 04-18 517228 (5000206) Screw 6
E70 04-18 664524 (9005110-9000) Plug assembly 1
E80 04-18 334987 Spring 2
F20 04-18 11116313 Slider block 1

Parts Manual
Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*QB83 *L25
B83
L10
QD50 D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C06
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: ELC

Model/Kit
L20 04-18 9006300-0156 Retaining ring 1
L50 04-18 684621 (9004104-1530) O-ring 1
L70 04-18 041160 (9007314-0605) Screw 3
QB83 04-18 085043 (9004201-3700) O-ring 1

Parts Manual
S90P 75cc special hardware FAA-FAK

Parts configuration
B83
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: FAA

C05 94-14 519253 (11025822) Cylinder block assembly 1
C80 94-14 518924 Valve plate 1
E82 94-14 360842 (11062703) Spring 2
QC04 94-14 8510365 Cylinder block kit 1
Order code: FAB

C80 94-14 518923 Valve plate 1
E82 94-14 360842 (11062703) Spring 2
Order code: FAC

C80 94-14 518008 Valve plate 1
E82 94-14 360842 (11062703) Spring 2
Order code: FAD

C80 96-05 518805 Valve plate 1
E82 96-05 360842 (11062703) Spring 2
Order code: FAK

C80 98-51 518805 Valve plate 1
E82 98-51 360842 (11062703) Spring 2

Parts Manual
S90P 75cc special hardware FAL, FAN

Parts configuration
B83
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: FAL

C80 94-14 518923 Valve plate 1
E82 94-14 360842 (11062703) Spring 2
Order code: FAN

C80 13-41 518924 Valve plate 1
E82 13-41 360842 (11062703) Spring 2

Parts Manual
S90P 75cc special hardware FAP-FAU

Parts configuration
B83
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: FAP

C80 94-14 518925 Valve plate, CW 1
E82 94-14 360842 (11062703) Spring 2
Order code: FAQ

C80 94-14 518925 Valve plate, CW 1
E82 94-14 360842 (11062703) Spring 2
Order code: FAR

C80 94-14 510723 Valve plate 1
E82 94-14 360842 (11062703) Spring 2
Order code: FAS

C80 97-03 518008 Valve plate 1
E82 97-03 360842 (11062703) Spring 2
Order code: FAU

C80 98-37 518805 Valve plate 1
E82 98-37 360842 (11062703) Spring 2

Parts Manual
S90P 75cc special hardware FAX, FAY

Parts configuration
B83
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: FAX

C80 01-07 510723 Valve plate 1
E82 01-07 360842 (11062703) Spring 2
Order code: FAY

C80 06-03 518805 Valve plate 1
E82 06-03 360842 (11062703) Spring 2

Parts Manual
S90P 75cc special hardware FAZ-FBG

Parts configuration
(FAZ)
W3CN
W1CN
B83
B2CN
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80 (FAY, FBA, FBC, FCF & FHP)

B83
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: FAZ

B2CN 05-06 775312 Set screw 1
C80 05-06 518008 Valve plate 1
E82 05-06 360842 (11062703) Spring 2
W1CN 05-06 723726 Connector 1
W3CN 05-06 574095 Cap 1
Order code: FBA

C80 06-12 518008 Valve plate 1
E82 06-12 360842 (11062703) Spring 2
Order code: FBC

C80 06-12 518805 Valve plate 1
E82 06-12 360842 (11062703) Spring 2
Order code: FBG

C80 06-16 518805 Valve plate 1
E82 06-16 360842 (11062703) Spring 2

Parts Manual
S90P 75cc special hardware FCF, FHP

Parts configuration
(FAZ)
W3CN
W1CN
B83
B2CN
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80 (FAY, FBA, FBC, FCF & FHP)

B83
QC04
C20
C30
C40
C05 E82
C50 E82
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: FCF

C80 11-19 518805 Valve plate 1
E82 11-19 360842 (11062703) Spring 2
Order code: FHP

C80 12-40 518805 Valve plate 1
E82 12-40 360842 (11062703) Spring 2

Parts Manual
S90P 75cc special hardware GAA-GBT

Parts configuration
B83
QC04
C20
C30
C40
C05
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: GAA

C80 94-14 344911 Valve plate 1
Order code: GBA

C80 87-02 518805 Valve plate 1
Order code: GBE

C80 98-06 518805 Valve plate 1
Order code: GBJ

C80 98-06 518805 Valve plate 1
Order code: GBS

C80 98-06 518805 Valve plate 1
Order code: GBT

C80 98-02 518805 Valve plate 1

Parts Manual
S90P 75cc special hardware GBU

Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*L25
B83
L10
QD50
D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C05
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: GBU

Model/Kit
B50 06-18 9004800-3708 Pin 2
B80 06-18 664524 (9005110-9000) Plug assembly 1
B84 06-18 11040532 Plug assembly 1
B92 06-18 11040532 Plug assembly 1
B94 06-18 11040532 Plug assembly 1
C30 06-18 11067350 Slipper guide 1
C50 06-18 11065865 Spacer 4
C70 06-18 314419 (9007276-0114) Screw 4
C80 06-18 518805 Valve plate 1
D10 06-18 519046 Servo arm 1
D50 06-18 11104315 Swashplate 1
D55 06-18 519150 Screw 1
D70 06-18 9009625-0146 Washer 1
D75 06-18 9004875-0098 Spiral head pin 1
D86 06-18 9004800-1908 Pin 1
D87 06-18 11040532 Plug assembly 1
E10 06-18 11001286 Side cover 1
E20 06-18 11042018 Leveler 1
E22 06-18 517935 Spring seat 2
E24 06-18 8801225 Shim 2
E30 06-18 11056531 Guide post 2
E40 06-18 505412 (9003509-0008) Seal nut 2
E50 06-18 517377 O-ring 1
E60 06-18 517228 (5000206) Screw 6
E70 06-18 664524 (9005110-9000) Plug assembly 1
E80 06-18 334987 Spring 2
F20 06-18 11116313 Slider block 1

Parts Manual
Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*L25
B83
L10
QD50
D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C05
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: GBU

Model/Kit
L20 06-18 9006300-0156 Retaining ring 1
L50 06-18 684621 (9004104-1530) O-ring 1
L70 06-18 041160 (9007314-0605) Screw 3

Parts Manual
S90P 75cc special hardware GBX-GCP

Parts configuration
B83
QC04
C20
C30
C40
C05
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: GBX

C80 08-42 518805 Valve plate 1
Order code: GCA

C80 98-14 518008 Valve plate 1
Order code: GCB

C80 98-14 518008 Valve plate 1
Order code: GCC

C80 98-06 518008 Valve plate 1
Order code: GCJ

C80 14-20 518805 Valve plate 1
Order code: GCP

C80 98-06 518008 Valve plate 1

Parts Manual
S90P 75cc special hardware GCR-GCU

Parts configuration
B83
QC04
C20
C30
C40
C05
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: GCR

C80 98-06 518805 Valve plate 1
Order code: GCS

C80 98-06 518008 Valve plate 1
Order code: GCU

C80 98-06 518008 Valve plate 1

Parts Manual
S90P 75cc special hardware GDE-GFP

Parts configuration
B83
QC04
C20
C30
C40
C05
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: GDE

C80 06-12 518805 Valve plate 1
Order code: GFD

C80 06-12 518805 Valve plate 1
Order code: GFH

C80 06-12 518805 Valve plate 1
Order code: GFJ

C80 06-12 518805 Valve plate 1
Order code: GFK

C80 06-12 518805 Valve plate 1
Order code: GFP

C80 06-12 518925 Valve plate, CW 1

Parts Manual
S90P 75cc special hardware GFS-GFZ

Parts configuration
B83
QC04
C20
C30
C40
C05
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: GFS

C80 06-12 518805 Valve plate 1
Order code: GFW

C80 06-12 518008 Valve plate 1
Order code: GFZ

C80 06-12 518805 Valve plate 1

Parts Manual
S90P 75cc special hardware GHT-GMA

Parts configuration
B83
QC04
C20
C30
C40
C05
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: GHT

C80 06-12 518008 Valve plate 1
Order code: GLA

C80 98-18 518925 Valve plate, CW 1
Order code: GLS

C80 98-18 518925 Valve plate, CW 1
Order code: GMA

C80 97-41 518007 Valve plate 1

Parts Manual
S90P 75cc special hardware GMC

Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*L25
B83
L10
QD50
D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C05
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: GMC

Model/Kit
B50 03-48 9004800-3708 Pin 2
B80 03-48 664524 (9005110-9000) Plug assembly 1
B84 03-48 11040532 Plug assembly 1
B92 03-48 11040532 Plug assembly 1
B94 03-48 11040532 Plug assembly 1
C30 03-48 11067350 Slipper guide 1
C50 03-48 11065865 Spacer 4
C70 03-48 314419 (9007276-0114) Screw 4
C80 03-48 518007 Valve plate 1
D10 03-48 519046 Servo arm 1
D50 03-48 11104315 Swashplate 1
D55 03-48 519150 Screw 1
D70 03-48 9009625-0146 Washer 1
D75 03-48 9004875-0098 Spiral head pin 1
D86 03-48 9004800-1908 Pin 1
D87 03-48 11040532 Plug assembly 1
E10 03-48 11001286 Side cover 1
E20 03-48 11042018 Leveler 1
E22 03-48 517935 Spring seat 2
E24 03-48 8801225 Shim 2
E30 03-48 11056531 Guide post 2
E40 03-48 505412 (9003509-0008) Seal nut 2
E50 03-48 517377 O-ring 1
E60 03-48 517228 (5000206) Screw 6
E70 03-48 664524 (9005110-9000) Plug assembly 1
E80 03-48 334987 Spring 2
F20 03-48 11116313 Slider block 1

Parts Manual
Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*L25
B83
L10
QD50
D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C05
C50 E90
E10
*C70
C80 E70 *E60

*E40
Model/Kit
L20 03-48 9006300-0156 Retaining ring 1

Parts Manual
(continued)
Model/Kit
L50 03-48 684621 (9004104-1530) O-ring 1
L70 03-48 041160 (9007314-0605) Screw 3

Parts Manual
S90P 75cc special hardware GMD

Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*L25
B83
L10
QD50
D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C05
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: GMD

Model/Kit
B50 03-48 9004800-3708 Pin 2
B80 03-48 664524 (9005110-9000) Plug assembly 1
B84 03-48 11040532 Plug assembly 1
B92 03-48 11040532 Plug assembly 1
B94 03-48 11040532 Plug assembly 1
C30 03-48 11067350 Slipper guide 1
C50 03-48 11065865 Spacer 4
C70 03-48 314419 (9007276-0114) Screw 4
C80 03-48 518925 Valve plate, CW 1
D10 03-48 519046 Servo arm 1
D50 03-48 11104315 Swashplate 1
D55 03-48 519150 Screw 1
D70 03-48 9009625-0146 Washer 1
D75 03-48 9004875-0098 Spiral head pin 1
D86 03-48 9004800-1908 Pin 1
D87 03-48 11040532 Plug assembly 1
E10 03-48 11001286 Side cover 1
E20 03-48 11042018 Leveler 1
E22 03-48 517935 Spring seat 2
E24 03-48 8801225 Shim 2
E30 03-48 11056531 Guide post 2
E40 03-48 505412 (9003509-0008) Seal nut 2
E50 03-48 517377 O-ring 1
E60 03-48 517228 (5000206) Screw 6
E70 03-48 664524 (9005110-9000) Plug assembly 1
E80 03-48 334987 Spring 2
F20 03-48 11116313 Slider block 1

Parts Manual
Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*L25
B83
L10
QD50
D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C05
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: GMD

Model/Kit
L20 03-48 9006300-0156 Retaining ring 1
L50 03-48 684621 (9004104-1530) O-ring 1
L70 03-48 041160 (9007314-0605) Screw 3

Parts Manual
S90P 75cc special hardware GME

Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*L25
B83
L10
QD50
D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C05
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: GME

Model/Kit
B50 03-48 9004800-3708 Pin 2
B80 03-48 664524 (9005110-9000) Plug assembly 1
B84 03-48 11040532 Plug assembly 1
B92 03-48 11040532 Plug assembly 1
B94 03-48 11040532 Plug assembly 1
C30 03-48 11067350 Slipper guide 1
C50 03-48 11065865 Spacer 4
C70 03-48 314419 (9007276-0114) Screw 4
C80 03-48 518008 Valve plate 1
D10 03-48 519046 Servo arm 1
D50 03-48 11104315 Swashplate 1
D55 03-48 519150 Screw 1
D70 03-48 9009625-0146 Washer 1
D75 03-48 9004875-0098 Spiral head pin 1
D86 03-48 9004800-1908 Pin 1
D87 03-48 11040532 Plug assembly 1
E10 03-48 11001286 Side cover 1
E20 03-48 11042018 Leveler 1
E22 03-48 517935 Spring seat 2
E24 03-48 8801225 Shim 2
E30 03-48 11056531 Guide post 2
E40 03-48 505412 (9003509-0008) Seal nut 2
E50 03-48 517377 O-ring 1
E60 03-48 517228 (5000206) Screw 6
E70 03-48 664524 (9005110-9000) Plug assembly 1
E80 03-48 334987 Spring 2
F20 03-48 11116313 Slider block 1

Parts Manual
Parts configuration
L60 L70
B80
L40
B72
B70
L20
B94 L50
*L25
B83
L10
QD50
D55
D65
QB30 B50 B84
F20
B92
D10
B50 B100
D86
D87
D50
D70
D75
E30
D80
E20
QC04 E22
C20
E80
C30 E24
*E50
C40
C05
C50 E90
E10
*C70
C80 E70 *E60

*E40

Parts Manual
Order code: GME

Model/Kit
L20 03-48 9006300-0156 Retaining ring 1
L50 03-48 684621 (9004104-1530) O-ring 1
L70 03-48 041160 (9007314-0605) Screw 3

Parts Manual
S90P 75cc special hardware GTA-PEA

Parts configuration
B83
(GTA, HCA, JAA, JCA, JCB,

PGA & PGB)
QC04
C20
C30
C40
C05
C50
*C70
C80
*QB83
B83
(PEA & PEB)
QC04
C20
C30
C40
C06
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: GTA

C80 98-18 518805 Valve plate 1
Order code: HCA

C80 98-18 518924 Valve plate 1
Order code: JAA

C80 97-41 518924 Valve plate 1
Order code: JCA

C80 08-12 518805 Valve plate 1
Order code: PEA

C06 07-04 11094260 (11011714) Cylinder block assembly with speed ring 1
C80 07-04 518805 Valve plate 1
QB83 07-04 085043 (9004201-3700) O-ring 1
QC04 07-04 8510366 Cylinder block kit with speed ring 1

Parts Manual
S90P 75cc special hardware PEB-PGB

Parts configuration
B83
(GTA, HCA, JAA, JCA, JCB,

PGA & PGB)
QC04
C20
C30
C40
C05
C50
*C70
C80
*QB83
B83
(PEA & PEB)
QC04
C20
C30
C40
C06
C50
*C70
C80

Parts Manual
Common parts
Model/Kit
C30 87-02 11067350 Slipper guide 1
C50 88-22 11065865 Spacer 4
C70 88-22 314419 (9007276-0114) Screw 4
Order code: PEB

C06 07-07 11094260 (11011714) Cylinder block assembly with speed ring 1
C80 07-07 518925 Valve plate, CW 1
QB83 07-07 085043 (9004201-3700) O-ring 1
QC04 07-07 8510366 Cylinder block kit with speed ring 1
Order code: PGA

C80 07-04 518805 Valve plate 1
Order code: PGB

C80 07-07 518925 Valve plate, CW 1

Parts Manual
Displacement
S90P 75cc displacement limitation 1-4

Parts configuration
F113
F105
*F112
F111
F105
(*F40)
(*F50)
F111
(*F40)
(*F50)
(*F12)
F10
(*F11)
(*F11)
(*F12)
F205
(*F50)
(*F40)
F205
F211
(*F50)
(*F40)
F213
*F212
F211
* Included in overhaul seal kit Q210
() Not available individually

Parts Manual
Displacement
Common parts
Model/Kit
F10 88-16 11041752 Servo piston assembly (SB-1988-009 on page 300 1
& SB-2000-022 on page 343)
F111 87-02 378083 (9007210-0804) Screw 3
F211 87-02 378083 (9007210-0804) Screw 3
Order code: 1
F105 87-02 11059759 (11055763) Servo cylinder assembly 1
F112 87-02 505412 (9003509-0008) Seal nut 1
F113 87-02 5000747 Set screw, M8 x45mm (SB-2000-022 on page 343) 1
Order code: 2
F212 87-02 505412 (9003509-0008) Seal nut 1
Order code: 3
Order code: 4
F112 87-02 505412 (9003509-0008) Seal nut 1
F212 87-02 505412 (9003509-0008) Seal nut 1

Parts Manual
Displacement
S90P 75cc displacement limitation 7

Parts configuration
F111
*F124
F022
F021
F020
F019 F105
(*F40)
F018 (*F50)
F016
F023
F015
F017
(*F12) F10
(*F11)
(*F11)
(*F12)
F100
F205
(*F50)
(*F40)
F211

Parts Manual
Displacement
Order code: 7
Model/Kit
F10 98-14 11041755 Servo piston assembly 1
F015 98-14 346395 Screw 1
F016 98-14 507092 Spring guide 1
F017 98-14 346320 Servo spring housing 1
F018 98-14 346254 Spring 1
F019 98-14 507093 Spring guide 1
F020 98-14 346379 Retaining ring 1
F021 98-14 787887 Castle nut 1
F022 98-14 336800 Nut 1
F023 98-14 11140220 Adjusting screw 1
F100 98-14 515310 (8100932) Servo assembly 1
F105 98-14 11060187 (11055767) Servo cylinder assembly, automotive control 1
F111 98-14 746651 (393595) Screw 3
F124 98-14 336826 Seal nut 1
F205 98-14 11059760 (11055761) Servo cylinder assembly, non-adjustable 1
F211 98-14 378083 (9007210-0804) Screw 3

Parts Manual
Displacement
S90P 75cc displacement limitation 8, B

Parts configuration
F113 F105
*F112
(8)
F111
F111 (*F40)
(*F50)
(*F40)
F105
(*F50)
(B)
(*F12)
(*F11) F10
(*F11)
(*F12)
F200
F017
F015
F023
F016
F018
F019
F205 F021
F020
F022
(*F50)
(*F40)
*F224
F211
() No available individually

Parts Manual
Displacement
Common parts
Model/Kit
F015 98-14 346395 Screw 1
F016 98-14 507092 Spring guide 1
F019 98-14 507093 Spring guide 1
F021 98-14 787887 Castle nut 1
F022 98-14 336800 Nut 1
F111 98-14 378083 (9007210-0804) Screw 3
F211 98-14 746651 (393595) Screw 3
F224 98-14 336826 Seal nut 1
Order code: 8
F018 98-14 346262 Spring 1
F112 98-14 505412 (9003509-0008) Seal nut 1
F113 98-14 5000747 Set screw, M8 x 45mm (SB-2000-022 on page 1
343)
F200 98-14 515324 (8100932) Servo assembly 1
Order code: B
F018 98-14 346254 Spring 1
F200 98-14 515310 (8100932) Servo assembly 1

Parts Manual
Displacement
S90P 75cc displacement limitation D

Parts configuration
F111
*F124
F022
F021
F020
F019 F105
(*F40)
F018 (*F50)
F016
F023
F015
F017
(*F12)
F10
(*F11)
(*F11)
(*F12)
F100
F205
(*F50)
(*F40)
F213
F211
*F212

Parts Manual
Displacement
Order code: D
Model/Kit
F015 98-14 346395 Screw 1
F016 98-14 507092 Spring guide 1
F018 98-14 346254 Spring 1
F019 98-14 507093 Spring guide 1
F021 98-14 787887 Castle nut 1
F022 98-14 336800 Nut 1
F100 98-14 515310 (8100932) Servo assembly 1
F105 98-14 11060187 (11055767) Servo cylinder assembly, automotive control 1
F111 98-14 746651 (393595) Screw 3
F124 98-14 336826 Seal nut 1
F211 98-14 378083 (9007210-0804) Screw 3
F212 98-14 505412 (9003508-0008) Seal nut 1
F213 98-14 5000747 Set screw (SB-2000-022 on page 343) 1

Parts Manual
Displacement
S90P 75cc displacement limitation F

Parts configuration
F111
(*F40)
(*F50)
(*F12)
F10
(*F11)
(*F11)
(*F12)
(*F50)
(*F40)
F211

Parts Manual
Displacement
Order code: F
Model/Kit
F10 91-30 11041752 Servo piston assembly (SB-2000-022 on page 1
343)
F111 91-30 378083 (9007210-0804) Screw 3
F211 91-30 378083 (9007210-0804) Screw 3

Parts Manual
Displacement
S90P 75cc displacement limitation H

Parts configuration
F113 F105
*F112
F111
(*F40)
(*F50)
(*F12)
(*F11) F10
(*F11)
(*F12)
F200
F017
F015
F023
F016
F018
F019
F205 F021
F020
F022
(*F50)
(*F40)
*F224
F211

Parts Manual
Displacement
Order code: H
Model/Kit
F015 98-14 346395 Screw 1
F016 98-14 507092 Spring guide 1
F018 98-14 346254 Spring 1
F019 98-14 507093 Spring guide 1
F021 98-14 787887 Castle nut 1
F022 98-14 336800 Nut 1
F111 98-14 378083 (9007210-0804) Screw 3
F112 98-14 505412 (9003509-0008) Seal nut 1
343)
F200 98-14 515310 (8100932) Servo assembly 1
F211 98-14 746651 (393595) Screw 3
F224 98-14 336826 Seal nut 1

Parts Manual
Displacement
S90P 75cc displacement limitation L

Parts configuration
F111
F113
(*F112)
*F124
F022
F021
F020
F019
(*F40)
F018 (*F50)
F016
F023
F015
F017
(*F12) F10
(*F11)
(*F11)
(*F12)
F100
F205
(*F50)
(*F40)
F213
F211
*F212

Parts Manual
Displacement
Order code: L
Model/Kit
F015 98-21 346395 Screw 1
F016 98-21 507092 Spring guide 1
F018 98-21 346254 Spring 1
F019 98-21 507093 Spring guide 1
F021 98-21 787887 Castle nut 1
F022 98-21 336800 Nut 1
F100 98-21 515310 (8100932) Servo assembly 1
F111 98-21 746651 (393595) Screw 3
F112 98-21 505412 (9003509-0008) Seal nut 1
343)
F124 98-21 336826 Seal nut 1
F211 98-21 378083 (9007210-0804) Screw 3
F212 98-21 505412 (9003509-0008) Seal nut 1
343)

Parts Manual
Displacement
S90P 75cc displacement limitation P

Parts configuration
F113
F105
*F112
F111
(*F40)
(*F50)
(*F12) F10
(*F11)
(*F11)
(*F12)
F205
(*F50)
(*F40)
F213
*F212
F211

Parts Manual
Displacement
Order code: P
Model/Kit
F10 98-41 11041752 Servo piston assembly (SB-2000-022 on page 1
343)
F111 98-41 378083 (9007210-0804) Screw 3
F112 98-41 505412 (9003509-0008) Seal nut 1
F113 98-41 719401 Set screw, M8 x 50mm 1
F211 98-41 378083 (9007210-0804) Screw 3
F212 98-41 505412 (9003509-0008) Seal nut 1
F213 98-41 719401 Set screw, M8 x 50mm 1

Parts Manual
End cap
S90P 75cc end cap H-6R

Parts configuration
G54
G20
G90 *G30
G18
G93 G04
G94
G95
G50
G97
G17
G40
G49
G52 G48

Parts Manual
End cap
Common parts
Model/Kit
G17 92-19 9005110-4400 Plug (SB-1992-003 on page 312) 1
G18 92-19 9005110-4400 Plug (SB-1992-003 on page 312) 1
G20 87-02 664763 (8700013) Journal bearing 1
G30 92-19 8100565 End cap gasket 1
G30 87-02 92-18 8100212 End cap gasket (SB-1992-003 on page 312) 1
G40 87-02 664771 (8700008) Bushing 1
G48 87-02 046151 (9005100-5600) Plug assembly 1
G49 87-02 046151 (9005100-5600) Plug assembly 1
G50 87-02 046151 (9005100-5600) Plug assembly 1
G52 87-02 140644 (9005110-5600) Plug assembly 1
G54 87-02 140644 (9005110-5600) Plug assembly 1
G90 92-19 746644 (9007314-0810) Screw 1
G90 87-02 92-18 9007210-0611 Screw (SB-1992-003 on page 312) 1
G93 92-19 713800 (8800564) Spacer 1
G93 87-02 92-18 8800404 Spacer 1
G94 92-19 8800565 Lifting bracket 1
G94 87-02 92-18 8800522 Lifting bracket 1
G95 92-19 502195 Washer 1
G95 87-02 92-18 9009610-2850 Washer 1
G97 96-05 746644 (9007314-0810) Screw 1
G97 92-19 96-04 5000060 Screw 1
G97 87-02 92-18 9007314-0604 Screw (SB-1992-003 on page 312) 1
Order code: 2, 6, 60, 61

G04 92-19 8100686 End cap assembly, side ports (SB-1992-003 on 1
page 312)
Order code: H, 62
G04 94-07 8100687 End cap assembly, metric side ports 1
Order code: 6R
G04 98-11 8100845 End cap assembly, metric side ports, CCW 1

Parts Manual
End cap
S90P 75cc end cap 60-67 (side ports built in Germany)

Parts configuration
(60 & 62)

*G30
G54
G20
G90
G04
G99
G50
G94
G17
G95
G49
G93
G40
G97
G48
G52
(67) *G30
G54
G20
G90
G04
G99
G50
G94
G95 G17
G49
G93
G40
G97
G48
G52

Parts Manual
End cap
Common parts
Model/Kit
G17 96-18 140644 Plug assembly 1
G30 96-18 8100565 End cap gasket 1
G40 96-18 664771 (8700008) Bushing 1
G90 96-18 746644 (9007314-0810) Screw 1
G93 96-18 713800 (8800564) Spacer 1
G95 96-18 502195 Washer 1
G97 96-18 395723 (9007315-0805) Screw 1
G99 96-18 746594 (9007314-0807) Screw 1
Order code: 60
G04 96-18 502277 End cap assembly, side ports 1
Order code: 62
G04 96-18 507891/P End cap assembly, metric side ports 1
Order code: 67
G04 96-18 502287 End cap assembly 1

Parts Manual
End cap
S90P 75cc end cap 6U, 6W

Parts configuration
*G30
(6U)
G20
G90
G04
G99
G50
G94
G17
G95
G49
G93
G40
G97
G48
*G30
(6W)
G20
G90
G04
G50
G94
G95 G17
G93 G49
G99 G40
G48

Parts Manual
End cap
Common parts
Model/Kit
G30 96-18 8100565 End cap gasket 1
G40 96-18 664771 (8700008) Bushing 1
G90 96-18 746644 (9007314-0810) Screw 1
G93 96-18 713800 (8800564) Spacer 1
G95 96-18 502195 Washer 1
G99 96-18 746594 (9007314-0807) Screw 1
Order code: 6U
G97 96-18 395723 (9007315-0805) Screw 1
Order code: 6W

Parts Manual
End cap
S90P 75cc end cap 1-81 (twin ports built in U.S.A)

Parts configuration
(1, 8, 80, 81 & 82)

G078 *G30
G068 G45
G54
G088
G20
G90
G04
G97
G40
G52
Old Design Twin Port G47
End Cap G46
*G30
(8W)
G04
G20
G90
G93
G94
G95
G97
G40

Parts Manual
End cap
Common parts
Model/Kit
G30 96-05 8100565 End cap gasket (SB-1995-012 on page 325) 1
G40 87-02 664771 (8700008) Bushing 1
G90 96-05 746644 (9007314-0810) Screw 1
G93 92-19 713800 (8800564) Spacer 1
G93 87-02 92-18 307678 (8800404) Spacer 1
G95 92-19 502195 Washer 1
G95 87-02 92-18 002295 (9009610-2850) Washer 1
G97 92-19 746644 (9007314-0810) Screw 1
G97 87-02 92-18 694356 (9007314-0608) Screw (SB-1992-003 on page 312) 1
G068 87-02 96-04 364281 Valve housing assembly (SB-1995-012) 1
G078 87-02 96-04 694356 (9007314-0608) Screw (SB-1995-012 on page 325) 4
G088 87-02 96-04 689117 Gasket (SB-1995-012 on page 325) 1
Order code: 8 & 80

G04 96-05 8100688 End cap assembly, twin ports (SB-1995-012 on 1
page 325)
G45 87-02 046151 (9005100-5600) Plug assembly 1
G46 87-02 046151 (9005100-5600) Plug assembly 1
G47 87-02 046151 (9005100-5600) Plug assembly 1
G52 87-02 140644 (9005110-5600) Plug assembly 1
G54 87-02 140644 (9005110-5600) Plug assembly 1
Order code: 1 & 81

G04 96-05 8100688 End cap assembly, twin ports (SB-1995-012 on 1
page 325)
G45 87-02 046151 (9005100-5600) Plug assembly 1
G46 87-02 046151 (9005100-5600) Plug assembly 1
G47 87-02 046151 (9005100-5600) Plug assembly 1
G52 87-02 515965 (9005110-5600) Plug assembly 1
G54 87-02 515965 (9005110-5600) Plug assembly 1

Parts Manual
End cap
S90P 75cc end cap 82, 8W (twin ports built in U.S.A)

Parts configuration
(1, 8, 80, 81 & 82)

G078 *G30
G068 G45
G54
G088
G20
G90
G04
G97
G40
G52
Old Design Twin Port G47
End Cap G46
*G30
(8W)
G04
G20
G90
G93
G94
G95
G97
G40

Parts Manual
End cap
Common parts
Model/Kit
G30 96-05 8100565 End cap gasket (SB-1995-012 on page 325) 1
G40 87-02 664771 (8700008) Bushing 1
G90 96-05 746644 (9007314-0810) Screw 1
G93 92-19 713800 (8800564) Spacer 1
G93 87-02 92-18 307678 (8800404) Spacer 1
G95 92-19 502195 Washer 1
G95 87-02 92-18 002295 (9009610-2850) Washer 1
G97 92-19 746644 (9007314-0810) Screw 1
G97 87-02 92-18 694356 (9007314-0608) Screw (SB-1992-003 on page 312) 1
G068 87-02 96-04 364281 Valve housing assembly (SB-1995-012) 1
G078 87-02 96-04 694356 (9007314-0608) Screw (SB-1995-012 on page 325) 4
G088 87-02 96-04 689117 Gasket (SB-1995-012 on page 325) 1
Order code: 82
G04 97-01 8100689 End cap assembly, metric twin ports 1
G45 87-02 046151 (9005100-5600) Plug assembly 1
G46 87-02 046151 (9005100-5600) Plug assembly 1
G47 87-02 046151 (9005100-5600) Plug assembly 1
G52 87-02 515965 (9005110-5600) Plug assembly 1
G54 87-02 515965 (9005110-5600) Plug assembly 1
Order code: 8W
G04 97-24 8100916 End cap assembly, twin ports, CW 1
G04 97-24 8100929 End cap assembly, twin ports, CCW 1

Parts Manual
End cap
S90P 75cc end cap 80-8V (twin ports build in Germany)

Parts configuration
(80, 82 & 8V)

G54 G45
G20
G90 G30
G04
G97
G40
G47
G46
(8D)
G54 G45
G20
G90 G30
G04
G72
G70
G97 G71
G40
G47
G46

Parts Manual
End cap
Common parts
Model/Kit
G30 96-18 8100565 End cap gasket 1
G40 96-18 664771 (8700008) Bushing 1
G90 96-18 746644 (9007314-0810) Screw 1
G93 96-18 713800 (8800564) Spacer 1
G95 96-18 502195 Washer 1
G97 96-18 746644 (9007314-0810) Screw 1
Order code: 80
G04 96-18 8100566 End cap assembly, twin ports 1
Order code: 82
G04 96-18 8100573/P End cap assembly, metric twin ports 1
Order code: 8D
G70 96-18 508211 Valve body 1
G71 96-18 508209 Spring 1
G72 96-18 521472 Retaining ring 1
Order code: 8V

Parts Manual
Charging system
S90P 75cc charging system C-F

Parts configuration
H40
(Germany only)
H25
H90
(L & N)
(L & N)
H40 H50
(Germany only) H90
H25
(N)
H70
H80
H60
H50
H40
H05
H60
(L) H50
H70
H80 H40
(F)
H80
H05
(C, D & E) H70

H80

Parts Manual
Charging system
Order code: C
Model/Kit
H05 93-10 8100479 Charge pump set, 14 cc (SB-1993-001 on page 1
315*)
H40 87-02 9004800-1222 Pin 1
H50 93-10 8801178 Charge pump shaft (SB-1993-001 on page 315 & 1
SB-1998-066 on page 330)
H50 87-02 89-16 8100142 Charge pump shaft (SB-1989-006 on page 308) 1
H60 87-02 9003310-1208 Key 1
H70 87-02 516761 Retaining plate 1
H80 87-02 648451 (9007210-0604) Screw 6
* For information regarding replacement parts for units built from 89-17 to 93-09, refer to AN152886483362 in the appendix.
Order code: D
315*)
H40 87-02 9004800-1222 Pin 1
SB-1998-066 on page 330)
H60 87-02 9003310-1208 Key 1
H80 87-02 648451 (9007210-0604) Screw 6
Order code: E
315*)
H40 87-02 9004800-1222 Pin 1
SB-1998-066 on page 330)
H60 87-02 9003310-1208 Key 1
H80 87-02 648451 (9007210-0604) Screw 6
Order code: F
H05 97-01 8200240 Charge pump set, 26 cc 1
H40 97-01 9004800-1224 Pin 1
H50 97-01 8801179 Charge pump shaft 1
H60 97-01 9003310-1208 Key 1
H80 97-01 672493 (9007210-0604) Screw 6

Parts Manual
Charging system
S90P 75cc charging system L, N

Parts configuration
H40
(Germany only)
H25
H90
(L & N)
(L & N)
H40 H50
(Germany only) H90
H25
(N)
H70
H80
H60
H50
H40
H05
H60
(L) H50
H70
H80 H40
(F)
H80
H05
(C, D & E) H70

H80

Parts Manual
Charging system
Order code: L
Model/Kit
H25 87-02 11077717 (8800466-0075) Charge pump spacer 1
H40 87-02 9004800-1222 Pin 1
SB-1998-066 on page 330)
H80 87-02 648451 (9007210-0604) Screw 6
H90 87-02 320002 (9005110-9200) Plug assembly 1
Order code: N
H25 98-51 11077717 (8800466-0075) Charge pump spacer 1
H40 98-51 9004800-1222 Pin 1
H80 98-51 648451 Screw 6
H90 98-51 320002 (9005110-9200) Plug assembly 1

Parts Manual
Charging system
S90P 75cc charging system S, Y

Parts configuration
(S)
H90
H60
H50
H40
(S)
H05
H90
H50
*J40
H25
H70
H80
(Y)
H80
(S)

Parts Manual
Charging system
Order code: S
Model/Kit
H25 96-24 509220 Charge pump spacer 1
H50 96-24 509221 Spacer 1
H80 96-24 648451 Screw 6
H90 96-24 320002 (9005110-9200) Plug assembly 1
J40 96-24 680892 (9004104-0440) O-ring 1
Order code: Y
H05 99-18 8200240 Charge pump set, 26 cc 1
H40 99-18 5000358 Pin 1
H50 99-18 8801210 Charge pump shaft 1
H60 99-18 9003310-1208 Key 1
H80 99-18 041160 (9007314-0605) Screw 6

Parts Manual
Auxiliary mounting
S90 pump aux mounting AB and AC

Parts configuration
J15
J30 J10
Design prior to 07-44 *J40

(used prior to 92-30)
J60
J70
J80
*J50
J90
J92
J95
J10
J15
J30
Design after 07-43
J60
J80
*J50
J90
J92
J95

Parts Manual
Auxiliary mounting
Order code: AB & A

Model/Kit
J10 87-02 8100147 Coupling, 9 tooth 1
J15 87-02 8800832 Cover assembly, CW (SB-1993-001 on page 315* 1
& SB-2005-011 on page 350)
J15 87-02 8800833 Cover assembly, CCW (SB-1993-001 on page 315* 1
& SB-2005-011 on page 350
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-29 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J60 87-02 8200467 Flange adapter, SAE A (SB-2007-027 on page 351) 1
J70 87-02 07-43 664920 (9009625-0132) Washer (SB-2007-027 on page 351) 4
J80 98-44 518721 Screw, M16 x 140 4
J80 87-02 98-43 9007314-1624 Screw, M16 x130 (SB-1989-023 on page 310) 4
J90 07-44 4800482 A pad seal (SB-2007-027 on page 351) 1
J90 87-02 07-43 545434 (9004100-0420) O-ring 1
J92 07-44 4460586 Cover plate (SB-2007-027 on page 351) 1
J92 87-02 07-43 9802336 Cover plate 1
J95 87-02 9007200-3714 Screw 3
* For information regarding replacement parts for units built from 89-17 to 93-09, refer to AN152886483362 in the appendix. New style covers may be
used with either charge pump design.
Order code: AC & T

J10 87-02 8100297 Coupling, 11 tooth 1
& SB-2005-011 on page 350)
& SB-2005-011 on page 350)
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-29 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J80 98-44 518721 Screw, M16 x 140 4
J80 87-02 98-43 9007314-1624 Screw M16 x 130 4
J90 87-02 07-43 545434 (9004100-0420) O-ring 1
J92 87-02 07-43 9802336 Cover plate 1
J95 87-02 9007200-3714 Screw 2

Parts Manual
Auxiliary mounting
S90P 75cc aux mounting AH-BA

Parts configuration
(AH)
J15
J30 J10
Design prior to 07-44
J60
*J40
J70
J80
*J50
J60
J90 J80
J92
J95
J90 Design after 07-43
J92
J95
J10
J15
J30
(B4 & BA)
J60
J80
*J50
J92
J90
J95

Parts Manual
Auxiliary mounting
Order code: AH
Model/Kit
J10 02-08 8100147 Coupling, 9 tooth 1
J15 02-08 8100649 Cover assembly, CW 1
J15 02-08 8100647 Cover assembly, CCW 1
J30 02-08 664771 (8700008) Bushing 1
J40 02-08 680892 (9004104-0440) O-ring 1
J50 02-08 056739 (9004104-1580) O-ring 1
J80 02-08 518721 Screw, M16 x 140 4
J90 02-08 07-43 545434 (9004100-0420) O-ring 1
J92 02-08 07-43 9802336 Cover plate 1
J95 02-08 9007200-3714 Screw 2
Order code: B4
J10 15-44 8100148 Coupling, 13 tooth 1
J30 15-44 664771 (8700008) Bushing 1
J50 15-44 056739 (9004104-1580) O-ring 1
J60 15-44 8100847 Flange adapter, SAE B 1
J80 15-44 518721 Screw, M16 x 140 4
J90 15-44 8801061 B pad seal 1
J92 15-44 8801059 Cover plate 1
J95 15-44 9007200-5021 Screw 2
Order code: BA
J10 06-15 8100273 Coupling, 15 tooth 1
J15 06-15 8801352 Cover assembly, CCW 1
J30 06-15 664771 (8700008) Bushing 1
J50 06-15 056739 (9004104-1580) O-ring 1
J60 06-15 8100847 Flange adapter, SAE B 1
J80 06-15 518721 Screw, M16 x 140 4
J90 06-15 8801061 B pad seal 1
J92 06-15 8801059 Cover plate 1
J95 06-15 9007200-5021 Screw 2

Parts Manual
Auxiliary mounting
S90P 75cc aux mounting BB-V

Parts configuration
J10
(BB & BC)
J15
J30
J60 *J40
J70
J80
J60 *J50
J90 J80
J92
J95
Design after 08-09

J90
J95
J92
Design prior to 08-10 J10

J60 (BD)
J70
J80
J60 *J50
J90 J80
J92
J95
J95
J92

Parts Manual
Auxiliary mounting
Order code: BB & V

Model/Kit
J10 87-02 8100273 Coupling,15 tooth 1
J15 87-02 8800832 Cover assembly, CW (SB-1993-001 on page 315*& 1
SB-2005-011 on page 350)
& SB-2005-011 on page 350)
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-15 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J60 87-02 8100847 Flange adapter, SAEB (SB-2007-055 on page 355) 1
J70 87-02 08-09 9009625-0132 Washer (SB-2007-055 on page 355) 4
J80 98-44 518721 Screw, M16x 140 4
J80 87-02 98-43 9007314-1622 Screw M16 x130 (SB-1998-073 on page 334) 4
J90 08-10 8801061 B pad seal (SB-2007-055 on page 355) 1
J90 87-02 08-09 726935 (9004104-0450) O-ring 1
J92 08-10 8801059 Coverplate (SB-2007-055 on page 355) 1
J92 87-02 08-09 4460370 Coverplate 1
J95 87-02 9007200-5021 Screw 2
Order code: BC & B

J10 87-02 8100148 Coupling, 13 tooth 1
& SB-2005-011 on page 350)
& SB-2005-011 on page 350)
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-15 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J60 87-02 8100847 Flange adapter, SAE B (SB-2007-055 on page 355) 1
J80 98-44 518721 Screw, M16 x 140 4
J80 87-02 98-43 9007314-1622 Screw M16 x 130 (SB-1998-073 on page 334) 4
J90 87-02 08-09 726935 (9004104-0450) O-ring 1
J92 87-02 08-09 4460370 Cover plate 1
J95 87-02 9007200-5021 Screw 2

Parts Manual
Auxiliary mounting
S90P 75cc aux mounting BD

Parts configuration
J10
(BB & BC)
J15
J30
J60 *J40
J70
J80
J60 *J50
J90 J80
J92
J95
Design after 08-09

J90
J95
J92

J60 (BD)
J70
J80
J60 *J50
J90 J80
J92
J95
J95
J92

Parts Manual
Auxiliary mounting
Order code: BD
Model/Kit
J10 06-10 8100148 Coupling, 13 tooth 1
J50 06-10 056739 (9004104-1580) O-ring 1
J80 06-10 518721 Screw, M16 x 140 4
J90 06-10 08-09 726935 (9004104-0450) O-ring 1
J92 06-10 08-09 4460370 Cover plate 1
J95 06-10 370320 Screw 2

Parts Manual
Auxiliary mounting
S90P 75cc aux mounting BE, BF

Parts configuration
J10
J15
J30
(BE)
J70
J80
J60 *J50
J90 J80
J92
J95
J90
Design after 08-09 J10

J95
J92 J15
J30
J60
(BF)
*J40
J70 (used prior to 92-30)
J80
J60 *J50
J80
J90
J92
J95
J90
Design after 08-09
J95
J92

Parts Manual
Auxiliary mounting
Order code: BE & P

Model/Kit
J10 95-21 8100148 Coupling,13 tooth 1
J15 95-21 8800832 Cover assembly, CW (SB-2005-011 on page 350) 1
J15 95-21 8800833 Cover assembly, CCW (SB-2005-011 on page 350) 1
J30 95-21 664771 (8700008) Bushing 1
J50 95-21 056739 (9004104-1580) O-ring 1
J60 95-21 8100938 Flange adapter, SAE B, metric threads 1
(SB-2007-055 on page 355)
J80 98-44 518721 Screw, M16x 140 4
J90 95-21 08-09 726935 (9004104-0450) O-ring 1
J92 95-21 08-09 4460370 Coverplate 1
J95 95-21 370320 (9007314-1207) Screw 2
Order code: BF & U

J10 87-02 11053342 Coupling,19 tooth 1
& SB-2005-011 on page 350)
& SB-2005-011 on page 350)
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-15 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J80 98-44 518721 Screw, M16x 140 4
J90 87-02 08-09 726935 (9004104-0450) O-ring 1
J92 87-02 08-09 4460370 Coverplate 1
J95 87-02 9007200-5021 Screw 2

Parts Manual
Auxiliary mounting
S90P 75cc aux mounting BH-BP

Parts configuration

(BH, BP & BR)
J10
J60
J70
J80
J60 *J50
J80
J90
J92
J95
J95
J92
J10
J15
J30
(BM)
J60
J70
J80
J60 *J50
J80
J90
J92
J95
J95
J92

Parts Manual
Auxiliary mounting
Order code: BH
Model/Kit
J10 06-13 8100148 Coupling, 13 tooth 1
J50 06-13 056739 (9004104-1580) O-ring 1
J80 06-13 518721 Screw, M16x 140 4
J90 06-13 09-30 726935 (9004104-0450) O-ring 1
J92 06-13 08-09 4460370 Coverplate 1
J95 06-13 9007200-5021 Screw 2
Order code: BM & 7

J10 94-07 8100273 Coupling, 15 tooth 1
J30 94-07 664771 (8700008) Bushing 1
J50 94-07 056739 (9004104-1580) O-ring 1
J60 94-07 8100938 Flange adapter, SAE B, metric threads 1
(SB-2007-055 on page 355)
J80 98-44 518721 Screw M16x 140 4
J90 06-13 08-09 726935 (9004104-0450) O-ring 1
J92 94-07 08-09 4460370 Coverplate 1
J95 94-07 737866 (9007314-1207) Screw 2
Order code: BP
J10 04-50 8100273 Coupling, 15 tooth 1
J50 04-50 056739 (9004104-1580) O-ring 1
J80 04-50 518721 Screw M16x 140 4
J90 04-50 09-30 726935 (9004104-0450) O-ring 1
J92 04-50 08-09 4460370 Coverplate 1
J95 04-50 9007200-5021 Screw 2

Parts Manual
Auxiliary mounting
S90P 75cc aux mounting BR

Parts configuration

(BH, BP & BR)
J10
J60
J70
J80
J60 *J50
J80
J90
J92
J95
J95
J92
J10
J15
J30
(BM)
J60
J70
J80
J60 *J50
J80
J90
J92
J95
J95
J92

Parts Manual
Auxiliary mounting
Order code: BR
Model/Kit
J10 04-50 8100273 Coupling, 15 tooth 1
J50 04-50 056739 (9004104-1580) O-ring 1
J80 04-50 518721 Screw M16x 140 4
J90 04-50 09-30 726935 (9004104-0450) O-ring 1
J92 87-02 08-09 4460370 Coverplate 1
J95 04-50 370320 (9007314-1207) Screw 2

Parts Manual
Auxiliary mounting
S90P 75cc aux mounting BT-CD

Parts configuration
J10
J15
J30
(BT)
J70
J80
J60 *J50
J90 J80
J92
J95
J90
Design after 08-09

J95
J92
*J40
(used prior to 92-30) J10
J15
J30
(CD & CK)
J70
J80
J60
*J50
J90
J95
J92
J90
J95
J80

Parts Manual
Auxiliary mounting
Order code: BT
Model/Kit
J10 05-12 11053346 Coupling, 14 tooth, high strength 1
& SB-2005-011 on page 350)
& SB-2005-011 on page 350)
J30 05-12 664771 (8700008) Bushing 1
J50 05-12 056739 (9004104-1580) O-ring 1
J80 98-44 518721 Screw, M16x 140 4
J90 05-12 08-09 726935 (9004104-0450) O-ring 1
J92 05-12 08-09 4460370 Coverplate 1
J95 05-12 9007200-5021 Screw 2
Order code: CD & C

& SB-2005-011 on page 350)
& SB-2005-011 on page 350)
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 92-15 680892 (9004104-0440) O-ring 1
J50 87-02 056739 (9004104-1580) O-ring 1
J60 87-02 8100897 Flange adapter, SAE C (SB-2007-051 on page 353) 1
J70 87-02 03-10 5000602 Washer (SB-2002-050 on page 346) 4
J80 98-44 518721 Screw, M16x 140 4
J90 08-19 11081805 C pad seal (SB-2007-051 on page 353) 1
J90 87-02 08-18 726943 (9004104-0490) O-ring 1
J92 87-02 08-18 8800406 Coverplate 1
J95 87-02 9007200-5021 Screw 4

Parts Manual
Auxiliary mounting
S90P 75cc aux mounting CK

Parts configuration
J10
J15
J30
(BT)
J70
J80
J60 *J50
J90 J80
J92
J95
J90
Design after 08-09

J95
J92
*J40
(used prior to 92-30) J10
J15
J30
(CD & CK)
J70
J80
J60
*J50
J90
J95
J92
J90
J95
J80

Parts Manual
Auxiliary mounting
Order code: CK
Model/Kit
J30 96-04 664771 (8700008) Bushing 1
J50 96-04 056739 (9004104-1580) O-ring 1
J80 98-44 518721 Screw M16x 140 4
J90 96-04 08-18 726943 (9004104-0490) O-ring 1
J92 96-04 08-18 4460370 Coverplate 1
J95 96-04 9007200-5021 Screw 4

Parts Manual
Auxiliary mounting
S90P aux mounting CP, CR

Parts configuration
J15
J30
(CP) J10
J60
J70
J80
J90
J60 *J50
J90
J92
J95
Design after 09-29
J80
J92
J95
J60
(CR)
J90 J10
*J50
J60
J90
J80
J95
J92
J80
Design after 08-09
J95
J92

Parts Manual
Auxiliary mounting
Order code: CP
Model/Kit
& SB-2005-011 on page 350)
& SB-2005-011 on page 350)
J30 93-14 664771 (8700008) Bushing 1
J50 93-14 056739 (9004104-1580) O-ring 1
J70 93-14 03-10 664920 Washer 4
J80 98-44 518721 Screw, M16x 140 4
J90 09-30 11081805 C-pad seal (SB-2007-051 on page 353) 1
J90 93-14 09-29 726943 (9004104-0490) O-ring 1
J92 93-14 09-29 8800406 Cover plate 1
J95 93-14 9007200-6222 Screw 2
Order code: CR
J50 03-14 056739 (9004104-1580) O-ring 1
J80 03-14 518721 Screw, M16x 140 4
J90 08-10 11081805 C-pad seal (SB-2007-051 on page 353) 1
J90 03-14 09-29 726943 (9004104-0490) O-ring 1
J92 03-14 09-29 8800406 Cover plate 1
J95 03-14 370320 Screw 4

Parts Manual
Auxiliary mounting
S90P 75cc aux mounting CT-CV

Parts configuration
J10
J15
(CT, CV, CW) J30
J60
J70
J80
J60
*J50
J90
J92
J95

J95
J92
J80
Design prior to 10-30 (CU)

J60
J70
J80 J10
J90
*J50
J60
J90
J95
J92
Design after 10-29

J95
J92

Parts Manual
Auxiliary mounting
Order code: CT
Item Date Begin Date End Part Number Part Number Qty. per
Model/Kit
J10 98-42 11053342 Coupling, 19 tooth 1
J30 98-42 664771 (8700008) Bushing 1
J50 98-42 056739 (9004104-1580) O-ring 1
J60 98-42 8100897 Flange adapter, SAE C (SB-2002-050 on page 346 1
& SB-2007-051 on page 353)
J80 98-44 518721 Screw, M16x 140 4
J90 08-10 11081805 C pad seal 1
J90 98-42 08-09 719179 (9004100-0480) O-ring 1
J92 08-10 8801060 Coverplate 1
J92 98-42 08-09 8800406 Coverplate 1
J95 98-42 9007200-5021 Screw 4
Order code: CU
J10 99-04 11053346 Coupling, 14 tooth,high strength 1
J50 99-04 056739 (9004104-1580) O-ring 1
J80 99-04 518721 Screw, M16x 140 4
J90 99-04 10-29 726943 (9004104-0490) O-ring 1
J92 99-04 10-29 8800406 Coverplate 1
J95 99-04 9007200-5021 Screw 4
Order code: CV
J30 00-16 664771 (8700008) Bushing 1
J50 00-16 056739 (9004104-1580) O-ring 1
J80 00-16 518721 Screw, M16x 140 4
J90 00-16 11081805 C pad seal 1
J92 00-16 8801060 Coverplate 1
J95 00-16 9007200-5021 Screw 4

Parts Manual
Auxiliary mounting
S90P 75cc aux mounting CW

Parts configuration
J10
J15
(CT, CV, CW) J30
J60
J70
J80
J60
*J50
J90
J92
J95

J95
J92
J80
Design prior to 10-30 (CU)

J60
J70
J80 J10
J90
*J50
J60
J90
J95
J92
Design after 10-29

J95
J92

Parts Manual
Auxiliary mounting
Order code: CW
Model/Kit
J10 98-46 11053346 Coupling, 14 tooth,high strength 1
J30 98-46 664771 (8700008) Bushing 1
J50 98-46 056739 (9004104-1580) O-ring 1
J60 98-46 8100897 Flange adapter, SAE C 1
J80 98-44 518721 Screw, M16x 140 4
J90 98-46 11081805 C pad seal 1
J92 98-46 8801060 Coverplate 1
J95 98-46 9007200-5021 Screw 2

Parts Manual
Auxiliary mounting
S90P 75cc aux mounting CX-NN

Parts configuration
Design prior to 09-30 J70 J60
J80
J90 J10
*J50
J60
J90
J92
J95
Design after 09-29

J80
J92
J95
J15 J30
J10
J60
J90 *J50
J80
J95 J15 *J40

J92
J30
J80

Parts Manual
Auxiliary mounting
Order code: CX
Model/Kit
J50 01-35 056739 (9004104-1580) O-ring 1
J80 01-35 518721 Screw, M16 x 140 4
J90 09-30 11081805 C pad seal 1
J90 01-35 09-29 726943 O-ring 1
J92 09-30 11048554 Cover plate 1
J92 01-35 09-29 350678 Cover plate 1
J95 01-35 9007200-6222 Screw 2
Order code: CZ
J30 02-08 664771 (8700008) Bushing 1
J50 02-08 056739 (9004104-1580) O-ring 1
J80 02-08 518721 Screw, M16 x 140 4
J90 02-08 11081805 C pad seal 1
J92 02-08 8801060 Cover plate 1
J95 02-08 9007200-5021 Screw 2
Order code: NN & N

J15 87-02 8800834 Cover assembly (SB-1993-001 on page 315*) 1
J30 87-02 664771 (8700008) Bushing 1
J40 87-02 680892 (9004104-0440) O-ring 1
J80 98-44 9007210-1621 Screw, M16 x 120 4
J80 87-02 98-43 9007210-1620 Screw, M16 x 100 (SB-1998-073 on page 334) 4
* For additional information regarding replacement parts for units built prior to 93-10, refer to AN152886483362 in the appendix

Parts Manual
S90P 75cc charge pressure setting

Parts configuration
(10-40, CB, XX) (JJ)

QK10 K01
K20
QK10
*K50
K40 *K50
*K51
K40
(JK)
K51
E70
K20
QK10
K50

Parts Manual
Order code: 10-30

Model/Kit
K50 87-42 001149 (9004201-6200) O-ring (SB-1989-002 on page 306) 1
QK10 87-42 8002K000-A Charge relief valve kit, 10-30 bar (SB-1989-002 on 1
page 306)
Order code: 32-42

K50 94-13 001149 (9004201-6200) O-ring 1
QK10 94-13 8510269 Charge relief valve kit, 30-42 bar 1
Order code: CB
K50 14-37 001149 (9004201-6200) O-ring 1
Order code: JD
none
Order code: JJ
K01 99-11 8100832 Externally mounted charge pressure relief valve 1
K20 99-11 8100816 Charge relief housing 1
K40 99-11 8000658 Nut 1
K50 99-11 001149 (9004201-6200) O-ring 1
K51 99-11 001156 (9004201-7500) O-ring 1
Order code: JK
E70 99-11 8100832 Externally mounted charge pressure relief valve 1
K20 99-11 8100816 Charge relief housing 1
K40 99-11 8000658 Nut 1
K50 99-11 001149 (9004201-6200) O-ring 1
K51 99-11 001156 (9004201-7500) O-ring 1
Order code: XX
K50 94-13 012559 (9004202-6200) O-ring, viton 1
QK10 94-13 11086335 Charge relief valve kit, viton 1

Parts Manual
Shaft
S90P 75cc shaft C6-SA

Parts configuration
L100

Parts Manual
Shaft
Order code: C6
Model/Kit
L100 87-02 318998 (8100299) Shaft, 21 tooth spline 1
Order code: C7
Order code: D7
L100 95-08 506860 Shaft, 23 tooth spline, M10 threaded tapped hole 1
Order code: D9
L100 95-08 11094648 (500054) Shaft, 21 tooth spline, M10 threaded tapped hole 1
Order code: G1
L100 97-15 504004 Shaft, 25 tooth spline 1
Order code: G6
L100 97-15 8100652 Shaft, 25 tooth spline, special 1
Order code: J1
L100 92-16 8100469 Shaft, 23 tooth spline, special length 1
Order code: S1
Order code: S3
Order code: S4
Order code: SA
L100 87-02 1713914 Shaft, 14 tooth spline long 1

Parts Manual
Shaft
S90P 75cc shaft G2, J8, K2

Parts configuration
(G2, J8)
L100
L80
(K2)
L100

Parts Manual
Shaft
Order code: G2
Model/Kit
Order code: J8
Order code: K2
L80 87-02 9003261-3724 Key 1
L100 87-02 8100354 Shaft, straight key, 1.5” diameter 1

Parts Manual
Shaft
S90P 75cc shaft T1-TJ

Parts configuration
(T1, T2)
(T6)
L90
L80 L90
L500
L100 L61
L100
(TG)
(TJ)
L200 L90 L90
L500
L200
L100
L100

Parts Manual
Shaft
Order code: T1
Model/Kit
L61 87-02 716779 (9004600-1230) Cotter pin 1
L80 87-02 9003310-3724 Key 1
L90 87-02 5000606 Slotted nut 1
L100 87-02 8100310 Shaft, 1.375” tapered 1
Order code: T2
L61 87-02 716779 (9004600-1230) Cotter pin 1
L80 87-02 9003310-3724 Key 1
L90 87-02 5000606 Slotted nut 1
L100 87-02 312009 (11114770) Shaft, 1.5” tapered 1
Order code: T6
L90 87-02 504060 Slotted nut 1
L100 87-02 511616 Shaft, 1.5” tapered 1
L500 87-02 511627 Washer 1
Order code: TG
L90 87-02 504060 Slotted nut 1
L100 87-02 504059 Shaft, 1.5” tapered 1
L200 87-02 504061 Flange adapter 1
Order code: TJ
L90 87-02 504060 Slotted nut 1
L100 87-02 511616 Shaft, 1.5” tapered 1
L200 87-02 511462 Coupling 1
L500 87-02 511627 Washer 1

Parts Manual
Control
S90P control CA-DD

Parts configuration
(CA) (DC & DD)

QM10
M90 M29
QM10
M76
*QM031
M11
M90
QM10
(CB)
M90
View A
*M11
M11
View “A”
T70 T50
T80
T20
(supply)
T30
M14 T40
Possible orifice locations
All orifices present in the original control must be transferred to the replacement control. If replacement
control contains pre-installed orifices, remove and discard them before transferring existing orifices to
new control.

Parts Manual
Control
Order code: CA
Model/Kit
M11 87-02 8800923 Control gasket 1
M90 87-02 693341 (9007314-0606) Screw 6
QM10 87-02 8102M0CA-A Control cover plate kit 1
Order code: CB
M14 96-40 11070306 Feedback link (SB-1999-019 on page 338 & 1
SB-2013-011 on page 359)
M14 87-02 96-39 8200344 Feedback link (SB-1996-009 on page 329) 1
M90 87-02 693341 (9007314-0606) Screw 6
QM10 87-02 8102M0CA-A Control cover plate kit 1
Order code: DC
M29 87-02 035592 Screw 4
M76 87-02 687103 Solenoid valve, 12v 1
M90 87-02 693341 (9007314-0606) Screw 6
QM10 87-02 8102M0DC-A Control kit, 12v 1
QM031 87-02 11099647 O-ring kit 1
QM210 87-02 11096172 Control seal kit 1
Order code: DD
M29 87-02 035592 Screw 4
M76 87-02 549907 Solenoid valve, 24v 1
M90 87-02 693341 (9007314-0606) Screw 6
QM10 87-02 8102M0DD-A Control kit, 24v 1
QM031 87-02 11099647 O-ring kit 1

Parts Manual
Control
S90P control EA, EG

Parts configuration
M9 M29
QM10
*M97
M90 *M96
*M95
*M51
View A
*M11
View “A”
M14
T20
(supply) T60
T50
(drain) T70 T80 (drain)
(servo feed) T30 (servo feed)
T40
(Possible orifice locations)
new control.
Generic PCP and swashplate used to show part location only.
* Included in control seal kit QM210

Parts Manual
Control
Order code: EA
Model/Kit
M9 91-16 MCV110A1017 PCP, MS connector 1
SB-2013-011 on page 359)
M29 91-16 K07067 Screw 4
M51 91-16 9003509-0008 Seal nut 1
M90 91-16 692889 (9007314-0611) Screw 6
M95 91-16 318337 (9004104-0120) O-ring 2
M96 91-16 011304 (9004104-0140) O-ring 1
M97 91-16 318345 (9004104-0240) O-ring 1
QM10 91-16 8202M0EA-B EDC kit, MS connector 1
Order code: EG
M9 91-16 12-35 MCV110A1018 PCP, MS connector 1
M11 91-16 12-35 8800923 Control gasket 1
M14 96-40 12-35 11070305 Feedback link (SB-1999-019 on page 338 & 1
SB-2013-011 on page 359)
M14 91-16 96-39 8000481 Feedback link (SB-1996-009) 1
M29 91-16 12-35 K07067 Screw 4
M51 91-16 12-35 9003509-0008 Seal nut 1
M90 91-16 12-35 692889 (9007314-0611) Screw 6
M95 91-16 12-35 318337 (9004104-0120) O-ring 2
M96 91-16 12-35 011304 (9004104-0140) O-ring 1
M97 91-16 12-35 318345 (9004104-0240) O-ring 1
QM10 91-16 12-35 11097110 EDC kit, MS connector 1
QM210 91-16 12-35 11096174 Control seal kit 1

Parts Manual
Control
S90P control EP, EX
Parts configuration
M9 M29
QM10
*M97
M90 *M96
*M95
*M51
View A
*M11
View “A”
M14
T20
(supply) T60
T50
T40
new control.
Generic PCP and swashplate used to show part location only.

Parts Manual
Control
Order code: EP
Model/Kit
M9 91-07 MCV110A1058 PCP, Packard connector 1
M14 96-40 11070305 Feedback link (SB-1999-019 & SB-2013-011) 1
M14 91-07 96-39 8000481 Feedback link (SB-1996-009) 1
M29 91-07 K07067 Screw 4
M51 91-07 9003509-0008 Seal nut 1
M90 91-07 692889 (9007314-0611) Screw 6
M95 91-07 318337 (9004104-0120) O-ring 2
M96 91-07 011304 (9004104-0140) O-ring 1
M97 91-07 318345 (9004104-0240) O-ring 1
QM10 91-07 8102M0EP-B EDC kit, Packard connector 1
Order code: EX
M9 93-16 MCV110A1090 PCP, Metri-pack connector 1
SB-2013-011 on page 359)
M29 93-16 K07067 Screw 4
M51 93-16 9003509-0008 Seal nut 1
M90 93-16 692889 (9007314-0611) Screw 6
M95 93-16 318337 (9004104-0120) O-ring 2
M96 93-16 011304 (9004104-0140) O-ring 1
M97 93-16 318345 (9004104-0240) O-ring 1
QM10 93-16 8102M0EX-B EDC kit, Packard connector 1

Parts Manual
Control
S90P control FA-FD

Parts configuration
QM10
M90
M005
M92
M007 M76
View A M29
*QM034
*M11
T70
T80
View “A”
T50
All orifices present in the original control must be transferred to the replacement control. If the
replacement control contains pre-installed orifices, remove and discard them before transferring existing
orifices to the new control.

Parts Manual
Control
Order code: FA
Model/Kit
M29 98-14 067694 Screw 4
M76 98-14 518080 Solenoid valve, 12 volt, 25 bar 2
M90 98-14 9007314-0614 Screw 3
M92 98-14 693341 (9007314-0606) Screw 3
M007 98-14 K00775 Filter screen 1
QM10 98-14 11015079 NFPE control kit, 12 volt, 25 bar 1
QM034 98-14 11099849 Solenoid valve seal kit 2
Order code: FB
M29 98-14 067694 Screw 4
M90 98-14 9007314-0614 Screw 3
M92 98-14 693341 (9007314-0606) Screw 3
Order code: FC
M29 98-14 067694 Screw 4
M90 98-14 9007314-0614 Screw 3
M92 98-14 693341 (9007314-0606) Screw 3
Order code: FD
M29 98-14 067694 Screw 4
M90 98-14 9007314-0614 Screw 3
M92 98-14 693341 (9007314-0606) Screw 3

Parts Manual
Control
S90P control FG, FH

Parts configuration
M90
M005
QM10
M92
View A
M76
M037
M036
*M11
*QM034
T70
T80
View “A”
T50

Parts Manual
Control
Order code: FG
Model/Kit
M90 00-30 9007314-0614 Screw 3
M92 00-30 693341 (9007314-0606) Screw 3
M005 00-30 11040532 Plug assembly 2
QM036 00-30 518088 Coil nut kit 2
QM037 00-30 516003 Coil, 12v Jet connector 2
Order code: FH
M90 00-30 9007314-0614 Screw 3
M92 00-30 693341 (9007314-0606) Screw 3
M005 00-30 11040532 Plug assembly 2
QM036 00-30 518088 Coil nut kit 2
QM037 00-30 516004 Coil, 24v Jet connector 2

Parts Manual
Control
S90P control FK-FN

Parts configuration
QM10
M29
QM034
M76

Parts Manual
Control
Order code: FK
Model/Kit
M29 02-27 346957 Screw 4
Order code: FL
M29 03-52 346957 Screw 4
Order code: FM
M29 04-06 346957 Screw 4
Order code: FN
M29 04-06 346957 Screw 4

Parts Manual
Control
S90P control HF-HS

Parts configuration
M90
QM10
*M51
View A
*M11
View “A”
M14
T20
T50 (supply) T80 T60
T70
(drain) (drain)
(servo feed) (servo feed)
T30
T40

Parts Manual
Control
Order code: HF
Model/Kit
M11 92-15 8801241 Control gasket (SB-1999-065 on page 341) 1
SB-2013-011 on page 359)
M51 92-15 505412 (9003509-0008) Seal nut 1
M90 92-15 692889 (9007314-0611) Screw 6
QM10 92-15 8202M0HF-A HDC kit, 3-11 bar 1
Order code: HK
SB-2013-011 on page 359)
M51 92-15 505412 (9003509-0008) Seal nut 1
M90 92-15 692889 (9007314-0611) Screw 6
QM10 92-15 8202M0HK-A HDC kit, 1-11 bar 1
Order code: HM
M11 92-15 8801241 Control gasket (SB-1999-065) 1
SB-2013-011 on page 359)
M51 92-15 505412 (9003509-0008) Seal nut 1
M90 92-15 692889 (9007314-0611) Screw 6
QM10 92-15 8202M0HM-A HDC kit, 1.1 -6.7 bar 1
Order code: HS
SB-2013-011 on page 359)
M51 94-19 505412 (9003509-0008) Seal nut 1
M90 94-19 692889 (9007314-0611) Screw 6
QM10 94-19 8202M0HS-A HDC kit, 6-18 bar 1

Parts Manual
Control
S90P control HU-JC

Parts configuration
QM10
M90 M90 QM10
M95*
M98
M51* M51*
View A View A
M11*
M11*
View “A”
M14
T20
T70
(drain)(servo feed) (servo feed) (drain)
T30
T40

Parts Manual
Control
Order code: HU
Model/Kit
M11 96-06 14-17 8801241 Control gasket (SB-1999-065 on page 341) 1
SB-2013-011 on page 359)
M51 96-06 14-17 505412 (9003509-0008) Seal nut 1
M90 96-06 14-17 692889 (9007314-0611) Screw 6
M95 96-06 14-17 611517 (9004100-0120) O-ring 4
M98 96-06 14-17 K14798 Screw 4
QM10 96-06 14-17 8510276 HDC kit, 3-11 bar 1
Order code: HX
M14 00-19 11070305 Feedback link (SB-2013-011 on page 359) 1
M51 00-19 505412 (9003509-0008) Seal nut 1
M90 00-19 692889 (9007314-0611) Screw 6
QM10 00-19 11015102 HDC kit, 3-11 bar 1
Order code: HY
M14 98-11 11070305 Feedback link 1
M51 98-11 505412 (9003509-0008) Seal nut 1
M90 98-11 692889 (9007314-0611) Screw 6
QM10 98-11 8510280 HDC kit, 4-14 bar 1
Order code: JC
M14 03-06 11070305 Feedback link 1
M51 03-06 505412 (9003509-0008) Seal nut 1
M90 03-06 692889 (9007314-0611) Screw 6
QM10 03-06 8510312 HDC kit, 6-18 bar, steel barrel 1

Parts Manual
Control
S90P control K0-K7

Parts configuration
QM10
M29
M9
M90
*M99
*M96 *M97
*M51
View A
*M11
M14 View “A”
T20 T60
T50 (supply) T80 (drain)
(drain) T70
T40

Parts Manual
Control
Order code: K0
Model/Kit
M9 02-49 MCV116G4217 PCP, Packard connector, dual coil 1
M14 02-49 11070305 Feedback link 1
M29 02-49 K07067 Screw 4
M51 02-49 505412 (9003509-0008) Seal nut 1
M90 02-49 692889 (9007314-0611) Screw 6
M96 02-49 011296 (9004105-0120) O-ring 3
M97 02-49 9004105-0130 O-ring 2
M99 02-49 K08572 Filter assembly 1
QM10 02-49 11015103 EDC3 kit, Packard connector, dual coil 1
Order code: K2
M9 09-22 MCV116G4214 PCP, DEUTSCH connector, dual coil 1
M29 09-22 K07067 Screw 4
M51 09-22 505412 (9003509-0008) Seal nut 1
M90 09-22 692889 (9007314-0611) Screw 6
M96 09-22 011296 (9004105-0120) O-ring 3
M97 09-22 9004105-0130 O-ring 2
QM10 09-22 11066897 EDC3 kit, DEUTSCH connector, dual coil 1
Order code: K7
M9 14-12 11101116 PCP, MS connector 1
M14 14-12 11070305 Feedback link 1
M29 14-12 K07067 Screw 4
M51 14-12 505412 (9003509-0008) Seal nut 1
M90 14-12 692889 (9007314-0611) Screw 6
M96 14-12 011296 (9004105-0120) O-ring 3
M97 14-12 9004105-0130 O-ring 2
QM10 14-12 11139993 EDC3 kit, MS connector 1

Parts Manual
Control
S90P control KA-KC

Parts configuration
QM10
M29
M9
M90
*M99
*M96 *M97
*M51
View A
*M11
M14 View “A”
T20 T60
(drain) T70
T40

Parts Manual
Control
Order code: KA
Model/Kit
M9 95-26 MCV116G4201 PCP, MS connector, dual coil 1
SB-2013-011 on page 359)
M29 95-26 K07067 Screw 4
M51 95-26 505412 (9003509-0008) Seal nut 1
M90 95-26 692889 (9007314-0611) Screw 6
M96 95-26 011296 (9004105-0120) O-ring 3
M97 95-26 9004105-0130 O-ring 2
QM10 95-26 8510115 EDC3 kit, MS connector, dual coil 1
Order code: KB
M9 15-25 11164284 PCP, cold oil special 1
SB-2013-011 on page 359)
M29 15-25 K07067 Screw 4
M51 15-25 505412 (9003509-0008) Seal nut 1
M90 15-25 692889 (9007314-0611) Screw 6
M96 15-25 011296 (9004105-0120) O-ring 3
M97 15-25 9004105-0130 O-ring 1
QM10 15-25 11166988 EDC3 kit, cold oil special 1
Order code: KC
M9 02-22 14-39 MCV116C1401 PCP, MS connector 1
M11 02-22 14-39 8800923 Control gasket 1
M29 02-22 14-39 K07067 Screw 4
M51 02-22 14-39 505412 (9003509-0008) Seal nut 1
M90 02-22 14-39 692889 (9007314-0611) Screw 6
M96 02-22 14-39 011296 (9004105-0120) O-ring 3
M97 02-22 14-39 9004105-0130 O-ring 2
M99 02-22 14-39 K08572 Filter assembly 1
QM10 02-22 14-39 11013634 EDC kit, MS connector, dual coil 1

Parts Manual
Control
S90P control KD-KH
Parts configuration
QM10
M29
M9
M90
*M99
*M96 *M97
*M51
View A
*M11
M14 View “A”
T20 T60
(drain) T70
T40

Parts Manual
Control
Order code: KD
Model/Kit
M9 97-49 MCV116F3113 PCP, Metripack 1
SB-2013-011 on page 359)
M29 97-49 K07067 Screw 4
M51 97-49 505412 (9003509-0008) Seal nut 1
M90 97-49 692889 (9007314-0611) Screw 6
M96 97-49 011296 (9004105-0120) O-ring 3
M97 97-49 9004105-0130 O-ring 1
QM10 97-49 8510246 EDC3 kit, Metripack 1
Order code: KE
M9 97-49 MCV116F3118 PCP, DEUTSCH connector 1
SB-2013-011 on page 359)
M29 97-49 K07067 Screw 4
M51 97-49 505412 (9003509-0008) Seal nut 1
M90 97-49 692889 (9007314-0611) Screw 6
M96 97-49 011296 (9004105-0120) O-ring 3
M97 97-49 9004105-0130 O-ring 1
QM10 97-49 8510322 EDC3 kit, DEUTSCH connector 1
Order code: KH
M9 00-06 MCV116G4211 PCP, cold oil special 1
M14 00-06 11070305 Feedback link 1
M29 00-06 K07067 Screw 4
M51 00-06 505412 (9003509-0008) Seal nut 1
M90 00-06 692889 (9007314-0611) Screw 6
M96 00-06 011296 (9004105-0120) O-ring 3
M97 00-06 9004105-0130 O-ring 1

Parts Manual
Control
S90P control KK-KP

Parts configuration
QM10
M29
M9
M90
*M99
*M96 *M97
*M51
View A
*M11
M14 View “A”
T20 T60
(drain) T70
T40

Parts Manual
Control
Order code: KK
Model/Kit
M9 00-06 MCV116G4211 PCP, cold oil special 1
M29 00-06 K07067 Screw 4
M51 00-06 505412 (9003509-0008) Seal nut 1
M90 00-06 692889 (9007314-0611) Screw 6
M96 00-06 011296 (9004105-0120) O-ring 3
M97 00-06 9004105-0130 O-ring 2
Order code: KN
M9 95-51 MCV116A3501 PCP, MS connector, single coil 1
SB-2013-011 on page 359)
M29 95-51 K07067 Screw 4
M51 95-51 505412 (9003509-0008) Seal nut 1
M90 95-51 692889 (9007314-0611) Screw 6
M96 95-51 011296 (9004105-0120) O-ring 3
M97 95-51 9004105-0130 O-ring 2
QM10 95-51 11013622 EDC3 kit, MS connector, single coil 1
Order code: KP
M9 95-26 MCV116G4204 PCP, Weather-pack connector, dual coil 1
SB-2013-011 on page 359)
M29 95-26 K07067 Screw 4
M51 95-26 505412 (9003509-0008) Seal nut 1
M90 95-26 692889 (9007314-0611) Screw 6
M96 95-26 011296 (9004105-0120) O-ring 3
M97 95-26 9004105-0130 O-ring 2
QM10 95-26 8510116 EDC3 kit, Weather-pack connector, dual coil 1

Parts Manual
Control
S90P control KT
Parts configuration
QM10
M29
M9
M90
*M99
*M96 *M97
*M51
View A
*M11
M14 View “A”
T20 T60
(drain) T70
T40

Parts Manual
Control
Order code: KT
Model/Kit
M9 99-49 MCV116G4214 PCP, DEUTSCH connector 1
M14 99-49 11070305 Feedback link 1
M29 99-49 K07067 Screw 4
M51 99-49 505412 (9003509-0008) Seal nut 1
M90 99-49 692889 (9007314-0611) Screw 6
M96 99-49 011296 (9004105-0120) O-ring 3
M97 99-49 9004105-0130 O-ring 2
QM10 99-49 8510298 EDC3 kit, DEUTSCH connector 1

Parts Manual
Control
S90P control KY, LB

Parts configuration
(KY) (LB)
QM10
QM10
M72
M90 M71
M29 M70
QM89
M90
M95
*M83
*M27
*M26
*M51
View A
*M11
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Control
Order code: KY
Model/Kit
M14 02-22 11070305 Feedback link 1
M29 02-22 K07067 Screw 4
M51 02-22 505412 (9003509-0008) Seal nut 1
M90 02-22 692889 (9007314-0611) Screw 6
M95 02-22 611517 (9004100-0120) O-ring 4
QM10 02-22 11015106 EDC3 w/HDC plate kit 1
Order code: LB
SB-1999-019 on page 338)
M26 96-40 144725 (9004105-0110) O-ring 1
M27 96-40 042557 (9006300-0044) Retaining ring 1
M70 96-40 8801007 Control handle 1
M71 96-40 689018 (9009660-3100) Toothlock washer 1
M72 96-40 040642 (9003513-0800) Nut 1
M83 96-40 001131 (9004201-5000) O-ring 1
M90 96-40 692889 (9007314-0611) Screw 6
QM10 96-40 8510173 MDC kit, w/4 lbs neutral start switch 1
QM89 96-40 8510174 Neutral start switch kit, 4 lbs, Weather-pack 1

Parts Manual
Control
S90P control LC, LE

Parts configuration
(LC)
QM10 (LE)
M76 QM10
M72
M71
M70
M78 QM89
*M77
M75 M72 M90
M90
M71
QM89 M70 *M83
*M27
*M26
*M83
M27
M26
View A
*M11
View A
*M11
View “A”
M14
T20
T70
(drain) (drain)
T30
T40

Parts Manual
Control
Order code: LC
Model/Kit
SB-2013-011 on page 359)
M26 97-06 144725 (9004105-0110) O-ring 1
M27 97-06 042557 (9006300-0044) Retaining ring 1
M72 97-06 040642 (9003513-0800) Nut 1
M75 97-06 505022 Control manifold 1
M76 97-06 11127986 Solenoid valve, 12 volt, 2-pole 1
M77 97-06 8800882 Manifold gasket 1
M78 97-06 693341 (9007314-0606) Screw 2
M83 97-06 001131 (9004201-5000) O-ring 1
M90 97-06 692889 (9007314-0611) Screw 6
QM10 97-06 11015107 MDC kit, w/neutral start switch, 2 pole 1
12vsolenoid
QM89 97-06 8510027 Neutral start switch kit 1
Order code: LE
M14 01-07 11070305 Feedback link 1
M26 01-07 144725 (9004105-0110) O-ring 1
M27 01-07 042557 (9006300-0044) Retaining ring 1
M72 01-07 040642 (9003513-0800) Nut 1
M83 01-07 001131 (9004201-5000) O-ring 1
M90 01-07 692889 (9007314-0611) Screw 6
QM10 01-07 8510291 MDC kit, high force neutral start switch 1
QM89 01-07 8510316 Neutral start switch kit, high force 1

Parts Manual
Control
S90P control LG, LK

Parts configuration
(LG)
(LK)
QM10
QM10
M76
M76
M78
M78 *M77 M72
M72 M75
*M77 M90 M71
M75 M71
M90 QM89 M70
M70
*M83
M27
M27 M26
M26
View A
View A
*M11
*M11
View “A”
M14
T20
T70
(drain) (drain)
T30
T40

Parts Manual
Control
Order code: LG
Model/Kit
M14 01-01 11070305 Feedback link 1
M26 01-01 144725 (9004105-0110) O-ring 1
M27 01-01 042557 (9006300-0044) Retaining ring 1
M72 01-01 040642 (9003513-0800) Nut 1
M78 01-01 693341 (9007314-0606) Screw 2
M90 01-01 692889 (9007314-0611) Screw 6
QM10 01-01 11015108 MDC kit, w/2-pole 12v solenoid 1
Order code: LK
M11 99-49 14-16 8800923 Control gasket 1
M14 99-49 14-16 11070305 Feedback link 1
M26 99-49 14-16 144725 (9004105-0110) O-ring 1
M27 99-49 14-16 042557 (9006300-0044) Retaining ring 1
M70 99-49 14-16 8801007 Control handle 1
M71 99-49 14-16 689018 (9009660-3100) Toothlock washer 1
M72 99-49 14-16 040642 (9003513-0800) Nut 1
M75 99-49 14-16 8800920 Control manifold 1
M76 99-49 14-16 8800921 Mechanical shunt valve 1
M77 99-49 14-16 8800882 Manifold gasket 1
M78 99-49 14-16 693341 (9007314-0606) Screw 2
M83 99-49 14-16 001131 (9004201-5000) O-ring 1
M90 99-49 14-16 692889 (9007314-0611) Screw 6
QM10 99-49 14-16 11015109 MDC kit, neutral start switch, shunt valve 1
QM89 99-49 14-16 8510174 Neutral start switch kit, high force, Weather-pack 1

Parts Manual
Control
S90P control LL, LN

Parts configuration
(LL) (LN)
QM10
M76
QM10 M76
M78
*M77 M72 M78
M75 M72
*M77
M90 M71 M75 M71
M90
QM89 M70 M70
*M83
M27 M27
M26 M26
View A View A
*M11 *M11
View “A”
M14
T20
T70
T30
T40

Parts Manual
Control
Order code: LL
Model/Kit
M14 02-16 11070305 Feedback link 1
M26 02-16 144725 (9004105-0110) O-ring 1
M27 02-16 042557 (9006300-0044) Retaining ring 1
M72 02-16 040642 (9003513-0800) Nut 1
M76 02-16 11127988 Solenoid valve, 12v, single pole 1
M78 02-16 693341 (9007314-0606) Screw 2
M83 02-16 001131 (9004201-5000) O-ring 1
M90 02-16 692889 (9007314-0611) Screw 6
QM10 02-16 8510393 MDC kit, w/single pole 12v solenoid 1
QM89 02-16 8510316 Neutral start switch kit, high force, Weather-pack 1
Order code: LN
M14 04-33 11070305 Feedback link 1
M26 04-33 144725 (9004105-0110) O-ring 1
M27 04-33 042557 (9006300-0044) Retaining ring 1
M72 04-33 040642 (9003513-0800) Nut 1
M78 04-33 693341 (9007314-0606) Screw 2
M90 04-33 692889 (9007314-0611) Screw 6
QM10 04-33 8100961 MDC kit, w/special orifice 1

Parts Manual
Control
S90P control LS, LT

Parts configuration
(LT)
(LS)
M72
QM10 M70
QM10
M72
M71
*M27
M70 *M029
*M28
*M26
QM89
M90 QM89
M90
*M83
*M83
*M27
*M26
View A
View A
*M11
*M11
View “A”
M14
T20
T70
(drain) (drain)
T30
T40

Parts Manual
Control
Order code: LS
Model/Kit
M14 13-45 11070305 Feedback link 1
M26 13-45 144725 (9004105-0110) O-ring 1
M27 13-45 042557 (9006300-0044) Retaining ring 1
M70 13-45 8801339 Control handle, offset 1
M72 13-45 040642 (9003513-0800) Nut 1
M83 13-45 001131 (9004201-5000) O-ring 1
M90 13-45 692889 (9007314-0611) Screw 6
QM10 13-45 8510360 MDC kit, with high force neutral start switch 1
Order code: LT
M14 06-13 11070305 Feedback link 1
M26 06-13 144725 (9004105-0110) O-ring 1
M27 06-13 042507 Retaining ring 1
M28 06-13 510690 Lip seal 1
M70 06-13 769075 Control handle, offset 1
M72 06-13 040642 (9003513-0800) Nut 1
M83 06-13 001131 (9004201-5000) O-ring 1
M90 06-13 692889 (9007314-0611) Screw 6
M029 06-13 512047 Washer 1
QM10 06-13 11098763 MDC kit, with high force neutral start switch 1
QM210 06-13 11109083 Control seal kit, with lip seal 1

Parts Manual
Control
S90P control M1, M2

Parts configuration
(M1)
(M2)
QM10
M72 QM10
M71
M70 M72
M71
M70
QM89 QM89
M90
M90
*M83
*M83
*M27
*M27 *M26
*M26
View A
View A *M11
*M11
View“A”
M14
T20
(supply) T60
T50 T70
(drain) (servo feed) T80 (drain)
T30 (servo feed)
T40

Parts Manual
Control
Order code: M1
Model/Kit
SB-2013-011 on page 359)
M26 95-37 144725 (9004105-0110) O-ring 1
M27 95-37 042507 (9006300-0044) Retaining ring 1
M72 95-37 040642 (9003513-0800) Nut 1
M90 95-37 692889 (9007314-0611) Screw 6
QM10 95-37 11014378 MDC kit, brass sleeve 1
Order code: M2
SB-2013-011 on page 359)
M26 95-37 144725 (9004105-0110) O-ring 1
M27 95-37 042507 (9006300-0044) Retaining ring 1
M72 95-37 040642 (9003513-0800) Nut 1
M83 95-37 001131 (9004201-5000) O-ring 1
M90 95-37 692889 (9007314-0611) Screw 6
QM10 95-37 8510112 MDC kit, with neutral start switch, brass sleeve 1
QM89 95-37 80020S40 Neutral start switch kit 1

Parts Manual
Control
S90P control M3
Parts configuration
QM10
M29
M76
M98
*QM031
M90
*M95
*M96 *M97 M72
View B M70
*M27
*M26
View A
*M11
M14
View “A” View “B”
T20
T50 (supply)
T70
(drain)
(servo feed) T30
T60 T40
T80
(drain)
(servo feed)

Parts Manual
Control
Order code: M3
Model/Kit
M14 14-18 11070305 Feedback link 1
M26 14-18 144725 (9004105-0110) O-ring 1
M27 14-18 042557 (9006300-0044) Retaining ring 1
M29 14-18 035592 Screw, M5 x 45 4
M72 14-18 040642 (9003513-0800) Nut 1
M76 14-18 11146844 Solenoid valve, DEUTSCH connector 1
M90 14-18 692889 (9007314-0611) Screw 6
M95 14-18 056713 O-ring 1
M96 14-18 056713 O-ring 1
M97 14-18 544742 O-ring 1
M98 14-18 067686 Screw, M5 x 20 4
QM10 14-18 11148988 MDC kit w/2-position solenoid, DEUTSCH 1
connector

Parts Manual
Control
S90P control M7, M8

Parts configuration
(M7) (M8)
QM10 QM10
M76 M29
M72
M71
M98
M70
QM89 *QM031
M90 M90
*M95 M72
*M83 *M96 *M97 M71
*M27
*M26 View B M70
*M27
*M26
View A
*M11
View A
*M11
M14
View“A” View“B”
T20
T50 (supply)
T70
(drain)
(servo feed) T30
T60 T40
T80
(drain)
(servo feed)

Parts Manual
Control
Order code: M7
Model/Kit
M26 11-04 144725 (9004105-0110) O-ring 1
M27 11-04 042507 (9006300-0044) Retaining ring 1
M72 11-04 040642 (9003513-0800) Nut 1
M83 11-04 001131 (9004201-5000) O-ring 1
M90 11-04 692889 (9007314-0611) Screw 6
QM10 11-04 11099070 MDC kit, with neutral start switch 1
QM89 11-04 709014 (8510170) Neutral start switch kit 1
Order code: M8
M14 04-38 11070306 Feedback link 1
M26 04-38 144725 (9004105-0110) O-ring 1
M27 04-38 042507 (9006300-0044) Retaining ring 1
M29 04-38 9007315-0507 Screw 4
M72 04-38 040642 (9003513-0800) Nut 1
M76 04-38 508009 Solenoid valve 1
M90 04-38 692889 (9007314-0611) Screw 6
M95 04-38 9004105-0140 O-ring 1
M96 04-38 9004105-0140 O-ring 1
M97 04-38 9004105-0190 O-ring 1
M98 04-38 9007315-0505 Screw 4
QM10 04-38 11015110 MDC kit, w/2-position solenoid valve 1
QM031 04-38 11099647 Solenoid seal kit 1

Parts Manual
Control
S90P control MA, MB

Parts configuration
(MA) (MB)
QM10
QM10
M72
M71
M72 M70
M90 M71
QM89
M70
M90
*M27
*M26
*M83
*M27
*M26
View A
View A
*M11
*M11
View“A”
M14
T20
(supply) T60
T50
T40

Parts Manual
Control
Order code: MA
Model/Kit
SB-2013-011 on page 359)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042507 (9006300-0044) Retaining ring 1
M72 87-02 040642 (9003513-0800) Nut 1
M90 87-02 692889 (9007314-0611) Screw 6
QM10 87-02 8102M0MA-A MDC kit 1
Order code: MB
SB-2013-011 on page 359)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042507 (9006300-0044) Retaining ring 1
M72 87-02 040642 (9003513-0800) Nut 1
M83 87-02 001131 (9004201-5000) O-ring 1
M90 87-02 692889 (9007314-0611) Screw 6
QM10 87-02 8102M0MB-A MDC kit with neutral start switch 1

Parts Manual
Control
S90P control MC, MD

Parts configuration
(MC) (MD)
QM10
M76 QM10
M76
M78
M78 *M77 M72
M72 M75
*M77
M75 M71 M90 M71
M90
M70 QM89 M70
*M83
M27 M27
M26 M26
View A View A
*M11 *M11
View“A”
M14
T20
(supply) T60
T50 T70
(drain) (servo feed) T80 (drain)
T30 (servo feed)
T40

Parts Manual
Control
Order code: MC
Model/Kit
SB-2013-011 on page 359)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042507 (9006300-0044) Retaining ring 1
M72 87-02 040642 (9003513-0800) Nut 1
M75 87-02 505022 Control manifold (SB-1995-003 on page 324) 1
M76 87-02 11127987 Solenoid valve, 12 volt, single pole 1
M78 95-10 693341 (9007314-0606) Screw (SB-1995-003 on page 324) 2
M78 87-02 95-09 041160 (9007314-0605) Screw 2
M90 87-02 692889 (9007314-0611) Screw 6
QM10 87-02 8102M0MC-A MDC kit w/12 volt solenoid, single pole 1
Order code: MD
M14 02-16 11070306 Feedback link 1
M26 02-16 144725 (9004105-0110) O-ring 1
M27 02-16 042507 (9006300-0044) Retaining ring 1
M72 02-16 040642 (9003513-0800) Nut 1
M76 02-16 11127986 Solenoid valve, 12v, double pole 1
M78 02-16 693341 (9007314-0606) Screw 2
M83 02-16 001131 (9004201-5000) O-ring 1
M90 02-16 692889 (9007314-0611) Screw 6
QM10 02-16 8102M0MD-A MDC kit, w/double pole 12v solenoid 1

Parts Manual
Control
S90P control ME, MG

Parts configuration
(ME)
(MG)
QM10
M76 M29 M76

QM10
M98
*QM031
M78
*M77 M72
M90 M75
*M95 M72 M90 M71
*M96 *M97 M71 QM89 M70
View B M70
*M83
*M27
*M26 M27
M26
View A
View A
*M11
*M11
M14
T20
T50 (supply)
T70
(drain)(servo feed)
T30
T60 T40
T80
(drain)
(servo feed)

Parts Manual
Control
Order code: ME
Model/Kit
SB-2013-011 on page 359)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042557 (9006300-0044) Retaining ring 1
M29 87-02 9007315-0510 Screw 4
M72 87-02 040642 (9003513-0800) Nut 1
M76 87-02 519357 Solenoid valve, 12 volt 1
M90 87-02 692889 (9007314-0611) Screw 6
M95 87-02 056713 (9004105-0140) O-ring 1
M96 87-02 056713 (9004105-0140) O-ring 1
M97 87-02 544742 (9004105-0190) O-ring 1
M98 87-02 9007315-0505 Screw 4
QM10 87-02 8102M0ME-A MDC kit w/2-position solenoid valve, 12 volt 1
QM031 87-02 11099647 Solenoid seal kit 1
Order code: MG
M14 02-16 11070305 Feedback link 1
M26 02-16 144725 (9004105-0110) O-ring 1
M27 02-16 042557 (9006300-0044) Retaining ring 1
M72 02-16 040642 (9003513-0800) Nut 1
M76 02-16 11127985 Solenoid valve, 24v, double pole 1
M78 02-16 693341 (9007314-0606) Screw 2
M83 02-16 001131 (9004201-5000) O-ring 1
M90 02-16 692889 (9007314-0611) Screw 6
QM10 02-16 8510061 MDC kit, w/double pole 24v solenoid 1
QM89 02-16 80020S40 Neutral start switch kit, high force 1

Parts Manual
Control
S90P control MH, MJ

Parts configuration
(MJ)
(MH)
QM10
M76
M72
M70 QM10
*M27 *QM031 M78

M90 *M029
*M28 M75
M77 M72
*M26
M71
M90
M70
*M27
*M26
View A
*M11
View A
*M11
View “A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Control
Order code: MH
Model/Kit
SB-2013-011 on page 359)
M26 87-02 144725 (9004105-0110) O-ring 1
M28 14-44 510690 Lip seal 1
M029 14-44 512047 Washer 1
M72 87-02 040642 (9003513-0800) Nut 1
M90 87-02 692889 (9007314-0611) Screw 6
QM10 87-02 8510282 MDC kit 1
Order code: MJ
M11 96-12 14-12 8800923 Control gasket 1
SB-2013-011 on page 359)
M26 96-12 14-12 144725 (9004105-0110) O-ring 1
M27 96-12 14-12 042557 (9006300-0044) Retaining ring 1
M70 96-12 14-12 9800916 Control handle 1
M71 96-12 14-12 689018 (9009660-3100) Toothlock washer 1
M72 96-12 14-12 040642 (9003513-0800) Nut 1
M76 96-12 14-12 8800921 Mechanical shunt valve 1
M78 96-12 14-12 693341 (9007314-0606) Screw 2
M90 96-12 14-12 692889 (9007314-0611) Screw 6
QM10 96-12 14-12 11015111 MDC kit, shunt valve 1
QM034 96-12 14-12 11099649 Shunt valve seal kit 1

Parts Manual
Control
S90P control MK, ML

Parts configuration
QM10
M72
M71
M70
QM89
M90
*M83
*M27
*M26
View A
*M11
View“A”
M14
T20
T50 (supply) T60
T70 T80
(drain) (drain)
T30
T40

Parts Manual
Control
Order code: MK
Model/Kit
SB-2013-011 on page 359)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042507 (9006300-0044) Retaining ring 1
M72 87-02 040642 (9003513-0800) Nut 1
M83 87-02 001131 (9004201-5000) O-ring 1
M90 87-02 692889 (9007314-0611) Screw 6
QM10 87-02 8102M0MK-A MDC kit w/wide deadband, nss 1
Order code: ML
SB-2013-011 on page 359)
M26 87-02 144725 (9004105-0110) O-ring 1
M27 87-02 042507 (9006300-0044) Retaining ring 1
M72 87-02 040642 (9003513-0800) Nut 1
M83 87-02 001131 (9004201-5000) O-ring 1
M90 87-02 692889 (9007314-0611) Screw 6
QM10 87-02 11015112 MDC kit w/wide deadband, high force nss 1

Parts Manual
Control
S90P control MN
Parts configuration
QM10
M76 M29
M98
*QM031
M90
*M95
*M96 *M97 M72
View B M70
*M27
*M26
View A
*M11
M14
T20
T50 (supply)
T70
(drain) (servo feed) T30
T60 T40
T80
(drain)
(servo feed)

Parts Manual
Control
Order code: MN
Model/Kit
M14 94-02 11070306 Feedback link 1
M26 94-02 144725 (9004105-0110) O-ring 1
M27 94-02 042507 (9006300-0044) Retaining ring 1
M29 94-02 035592 Screw, M5 x 45 4
M72 94-02 040642 (9003513-0800) Nut 1
M90 94-02 692889 (9007314-0611) Screw 6
M95 94-02 056713 O-ring 1
M96 94-02 056713 O-ring 1
M97 94-02 544742 O-ring 1
M98 94-02 067686 Screw, M5 x 20 4
QM10 94-02 11087557 MDC kit w/2-position solenoid 1

Parts Manual
Control
S90P control MR, MS

Parts configuration
(MR)
QM10 (MS)
M76 QM10
M72
M71
M70
M78 QM89
*M77
M75 M72 M90
M90
M71
QM89 M70 *M83
*M27
*M26
*M83
M27
M26
View A
*M11
View A
*M11
View “A”
M14
T20
T70
(drain) (drain)
T30
T40

Parts Manual
Control
Order code: MR
Model/Kit
M14 96-43 11070305 Feedback link 1
M26 96-43 144725 (9004105-0110) O-ring 1
M27 96-43 042557 (9006300-0044) Retaining ring 1
M72 96-43 040642 (9003513-0800) Nut 1
M76 96-43 11127985 Solenoid valve, 24 volt, double pole 1
M78 96-43 693341 (9007314-0606) Screw 2
M83 96-43 001131 (9004201-5000) O-ring 1
M90 96-43 692889 (9007314-0611) Screw 6
QM10 96-43 8510394 MDC kit w/24 v solenoid, 2-pole, high force nss 1
QM89 96-43 709014 (8510027) Neutral start switch kit, high force 1
Order code: MS
M14 01-07 11070305 Feedback link 1
M26 01-07 144725 (9004105-0110) O-ring 1
M27 01-07 042557 (9006300-0044) Retaining ring 1
M72 01-07 040642 (9003513-0800) Nut 1
M83 01-07 001131 (9004201-5000) O-ring 1
M90 01-07 692889 (9007314-0611) Screw 6
QM10 01-07 8510287 MDC kit, high force neutral start switch 1

Parts Manual
Control
S90P control MT, MV

Parts configuration
(MT)
QM10
(MV) QM10
M76
M72
M71
M70
M78
M72 QM89
*M77
M75 M71 M90
M90
M70
*M83
*M27
*M26
M27
M26
View A
*M11
View A
*M11
View “A”
M14
T20
T70
(drain) (drain)
T30
T40

Parts Manual
Control
Order code: MT
Model/Kit
M14 01-01 11070305 Feedback link 1
M26 01-01 144725 (9004105-0110) O-ring 1
M27 01-01 042557 (9006300-0044) Retaining ring 1
M72 01-01 040642 (9003513-0800) Nut 1
M78 01-01 693341 (9007314-0606) Screw 2
M90 01-01 692889 (9007314-0611) Screw 6
QM10 01-01 8510320 MDC kit, w/2-pole 12v solenoid 1
Order code: MV
SB-2013-011 on page 359)
M26 94-30 144725 (9004105-0110) O-ring 1
M27 94-30 042557 (9006300-0044) Retaining ring 1
M72 94-30 040642 (9003513-0800) Nut 1
M83 94-30 001131 (9004201-5000) O-ring 1
M90 94-30 692889 (9007314-0611) Screw 6
QM10 94-30 8510342 MDC kit, nss w/weatherpack connector, 2-way 1
QM89 94-30 8510170 Neutral start switch kit, weather pack connector, 1
2-way

Parts Manual
Control
S90P control MW
Parts configuration
QM10
M76 M29
M98
*QM031
M90
*M95
*M96 *M97 M72
View B M70
*M27
*M26
View A
*M11
M14
T20
T50 (supply)
T70
(drain)
(servo feed) T30
T60 T40
T80
(drain)
(servo feed)

Parts Manual
Control
Order code: MW
Model/Kit
M14 14-18 11070305 Feedback link 1
M26 14-18 144725 (9004105-0110) O-ring 1
M27 14-18 042557 (9006300-0044) Retaining ring 1
M29 14-18 035592 Screw, M5 x 45 4
M72 14-18 040642 (9003513-0800) Nut 1
M76 14-18 11146844 Solenoid valve, DEUTSCH connector 1
M90 14-18 692889 (9007314-0611) Screw 6
M95 14-18 056713 O-ring 1
M96 14-18 056713 O-ring 1
M97 14-18 544742 O-ring 1
M98 14-18 067686 Screw, M5 x 20 4
QM10 14-18 11148990 MDC kit w/2-position solenoid, DEUTSCH 1
connector

Parts Manual
Control
S90P control MX, MY

Parts configuration
(MX)
QM10
(MY)
M76 QM10
M72
M70
M78 *M27
M72 M90 *M029
*M77
M75 M71 *M28
M90
M70 *M26
M27
M26
View A
*M11
View A
*M11
View “A”
M14
T20
T70
(drain) (drain)
T30
T40

Parts Manual
Control
Order code: MX
Model/Kit
SB-2013-011 on page 359)
M26 94-30 144725 (9004105-0110) O-ring 1
M27 94-30 042557 (9006300-0044) Retaining ring 1
M72 94-30 040642 (9003513-0800) Nut 1
M75 94-30 505022 Control manifold (SB-1995-003 on page 324) 1
M76 94-30 11127988 Solenoid valve, 12 volt, single pole 1
M78 95-10 693341 (9007314-0606) Screw (SB-1995-003 on page 324) 2
M78 94-30 95-09 041160 (9007314-0605) Screw 2
M90 94-30 692889 (9007314-0611) Screw 6
QM10 94-30 11015113 MDC kit w/12 volt solenoid, single pole 1
Order code: MY
SB-2013-011 on page 359)
M26 87-02 144725 (9004105-0110) O-ring 1
M28 15-05 510690 Lip seal 1
M029 15-05 512047 Washer 1
M72 96-07 040642 (9003513-0800) Nut 1
M90 96-07 692889 (9007314-0611) Screw 6
QM10 96-07 11087559 MDC kit 1

Parts Manual
Control
S90P control NA, NC

Parts configuration
(NC)
QM10 (NA)
QM10
M76
M72
M90 M71
M70
*M27
*M26 M78
*M77
M75
M90 M72
M70
*M27
M51 *M26
View A
*M11
M51
View A
*M11
M14
T20
T70 (supply) T80
T30
T40

Parts Manual
Control
Order code: NA
Model/Kit
SB-2013-011 on page 359)
M26 94-30 144725 (9004105-0110) O-ring 1
M27 94-30 042557 (9006300-0044) Retaining ring 1
M51 94-30 345462 Nut 1
M70 94-30 769075 Control handle, sharp bend 1
M72 94-30 040642 (9003513-0800) Nut 1
M90 94-30 9007314-0614 Screw 6
QM10 94-30 8102M0NA-A MDC kit, NL 1
Order code: NC
M11 94-50 14-42 504733 Control gasket 1
SB-2013-011 on page 359)
M26 94-30 14-42 144725 (9004105-0110) O-ring 1
M27 94-30 14-42 042557 (9006300-0044) Retaining ring 1
M51 94-30 14-42 345462 Nut 1
M70 94-50 14-42 9800916 Control handle 1
M72 94-50 14-42 040642 (9003513-0800) Nut 1
M76 94-50 14-42 9700803 Solenoid valve 1
M78 94-50 14-42 693341 (9007314-0606) Screw 2
M90 94-50 14-42 9007314-0614 Screw 6
QM10 94-50 14-42 11098758 MDC kit, NL 1

Parts Manual
Control
S90P control NE
Parts configuration
QM10 M75
M78
M76
*M77
M72
M90 M70
*M27
*M26
M51
View A
*M11
M14
T20
T70 (supply) T80
T30
T40

Parts Manual
Control
Order code: NE
Model/Kit
M11 94-05 14-15 504733 Control gasket 1
SB-2013-011 on page 359)
M26 94-05 14-15 144725 (9004105-0110) O-ring 1
M27 94-05 14-15 042557 (9006300-0044) Retaining ring 1
M51 94-05 14-15 345462 Nut 1
M70 94-05 14-15 769075 Control handle, sharp bend 1
M72 94-05 14-15 040642 (9003513-0800) Nut 1
M75 94-05 14-15 500147 Control manifold assembly 1
M76 94-05 14-15 8700100 Solenoid valve 1
M78 94-05 14-15 692889 (9007314-0611) Screw 2
M90 94-05 14-15 9007314-0614 Screw 6
QM10 94-05 14-15 11098759 MDC kit, NL 1

Parts Manual
Control
S90P control NU
Parts configuration
QM10
M75
M29
M76
*M77
M72
QM89 M70
M90 *M83
*M27
*M26
M51
View A
*M11
M14
T20
T70 (supply) T80
T30
T40

Parts Manual
Control
Order code: NU
Model/Kit
SB-2013-011 on page 359)
M26 94-05 144725 (9004105-0110) O-ring 1
M27 94-05 042507 (9006300-0044) Retaining ring 1
M29 94-05 692889 (9007314-0611) Screw 2
M51 94-05 345462 Nut 1
M72 94-05 040642 (9003513-0800) Nut 1
M75 94-05 500147 Control manifold assembly 1
M76 94-05 8700100 Solenoid valve 1
M83 94-05 784686 (9004104-0130) O-ring 1
M90 94-05 9007314-0614 Screw 6
QM10 94-05 11015114 MDC kit, NL w/nss 1
QM89 94-05 11087773 Back-up alarm switch kit 1

Parts Manual
Control
S90P 75cc control PA, PB

Parts configuration
(PA & PB) (PE)
QM036 QM76
QM10 QM10
M76
M9 *QM034 QM037
*M658
M29 M29
M90 *M97 M9
*M96
M90
*M95
*M96
*M51
*M11 *M51
*M11
M14
View “A”
T20
(supply)
T50 T60
(drain) T70 T80
(drain)
T40

Parts Manual
Control
Control code: PA
Model/Kit
M9 94-07 782037 PDC, 12 volt 1
SB-2013-011 on page 359)
M29 94-07 035592 Screw 4
M51 94-07 9003509-0008 Seal nut 1
M76 94-07 11001795 Solenoid, 12 volt, din connector 2
M90 94-07 692889 (9007314-0611) Screw 6
M95 94-07 011296 (9004105-0120) O-ring 2
M96 94-07 688721 (9004104-0170) O-ring 1
M97 94-07 314534 (9004104-0310) O-ring 1
M658 94-07 635938 (9004100-0210) O-ring 2
QM10 94-07 8510166 HDC2, w/PDC 1
Order code: PB
M9 94-15 782045 PDC, 24 volt 1
SB-2013-011 on page 359)
M29 94-15 035592 Screw 4
M51 94-15 9003509-0008 Seal nut 1
M76 94-15 11001794 Solenoid, 24 volt, din connector 2
M90 94-15 692889 (9007314-0611) Screw 6
M95 94-15 011296 (9004105-0120) O-ring 2
M96 94-15 688721 (9004104-0170) O-ring 1
M97 94-15 314534 (9004104-0310) O-ring 1
M658 94-15 635938 (9004100-0210) O-ring 2
QM10 94-15 11034092 Electro-hydraulic control kit 1

Parts Manual
Control
S90P control PE
Parts configuration
(PA & PB) (PE)
QM036 QM76
QM10 QM10
M76
M9 *QM034 QM037
*M658
M29 M29
M90 *M97 M9
*M96
M90
*M95
*M96
*M51
*M11 *M51
*M11
M14
View “A”
T20
(supply)
T50 T60
(drain) T70 T80
(drain)
T40

Parts Manual
Control
Order code: PE
Model/Kit
M9 10-30 11175053 HIC, proportional reducing manifold assembly 1
M14 10-30 11070306 Feedback link 1
M29 10-30 K28807 Screw 4
M51 10-30 9003509-0008 Seal nut 1
M90 10-30 692889 (9007314-0611) Screw 6
M96 10-30 9004105-0120 O-ring 4
QM10 10-30 8510286 EDC, high current, 3-11 bar, 12 volt 1
QM036 10-30 11175054 Coil nut 2
QM037 10-30 11175055 Coil, 12 volt 2
QM76 10-30 11175056 Solenoid valve, 12 volt 2

Parts Manual
Control
S90P control PF, PG

Parts configuration
(PF) (PG)
QM10 QM10
M76 M76
M9 M9
*M658 *M658
M29 M29
M90 *M97 M90 *M97
*M96 *M96
*M95 *M95
*M51 *M51
*M11 *M11
View “A”
M14
T20
T70
T30
T40

Parts Manual
Control
Order code: PF
Model/Kit
M9 03-32 519719 PDC, 12 volt 1
M29 03-32 035592 Screw 4
M51 03-32 9003509-0008 Seal nut 1
M76 03-32 11001793 Solenoid, 12 volt, AMP connector 2
M90 03-32 692889 (9007314-0611) Screw 6
M95 03-32 011296 (9004105-0120) O-ring 2
M96 03-32 688721 (9004104-0170) O-ring 1
M97 03-32 314534 (9004104-0310) O-ring 1
M658 03-32 635938 (9004100-0210) O-ring 2
QM10 03-32 11098760 EDC2, 12 volt, AMP connector 1
Order code: PG
M9 06-13 11001679 PDC, 12 volt 1
M29 06-13 035592 Screw 4
M51 06-13 9003509-0008 Seal nut 1
M76 06-13 11001793 Solenoid, 12 volt, AMP connector 2
M90 06-13 692889 (9007314-0611) Screw 6
M95 06-13 011296 (9004105-0120) O-ring 2
M96 06-13 688721 (9004104-0170) O-ring 1
M97 06-13 314534 (9004104-0310) O-ring 1
M658 06-13 635938 (9004100-0210) O-ring 2
QM10 06-13 11098761 EDC2, 12 volt, AMP connector 1

Parts Manual
Control
S90P control PH, PJ

Parts configuration
QM76
QM10 QM036
QM037
*QM034 M29
M9
M90
*M96
*M51
*M11
View “A”
M14
T20
T70
T30
T40

Parts Manual
Control
Order code: PH
Model/Kit
M14 13-37 11070305 Feedback link 1
M29 13-37 K28807 Screw 4
M51 13-37 9003509-0008 Seal nut 1
M90 13-37 692889 (9007314-0611) Screw 6
M96 13-37 9004105-0120 O-ring 4
QM10 13-37 11121735 EDC, high current 1
QM036 13-37 11175058 Coil nut 2
QM037 13-37 11175059 Coil, 12 volt 2
Order code: PJ
M14 14-15 11070305 Feedback link 1
M29 14-15 K28807 Screw 4
M51 14-15 9003509-0008 Seal nut 1
M90 14-15 692889 (9007314-0611) Screw 6
M96 14-15 9004105-0120 O-ring 4
QM10 14-15 11141115 EDC, high current 1
QM036 14-15 11175058 Coil nut 2
QM037 14-15 11175074 Coil, 24 volt 2

Parts Manual
Control
S90P control RR, RS

Parts configuration
QM10
(RR) (RS & RU)
M72 M72
M70 M70
M76
M92
*M27
*M029
*M28
M90 *M26
QM89
*QM83
View A
*M11
M14 View “A”
T20
T70 (supply) T80
T30
T40

Parts Manual
Control
Order code: RR
Model/Kit
M26 99-06 144725 (9004105-0110) O-ring 1
M27 99-06 042507 (9006300-0044) Retaining ring 1
M28 99-06 510690 Lip seal 1
M72 99-06 040642 (9003513-0800) Nut 1
M90 99-06 354407 Screw 5
M92 99-06 510382 Screw 1
QM10 99-06 8510245 MDC kit, roller 1
QM83 99-06 001131 (9004201-5000) O-ring 1
QM89 99-06 11099847 Neutral start switch, high force 1
Order code: RS
M26 01-15 144725 (9004105-0110) O-ring 1
M27 01-15 042507 (9006300-0044) Retaining ring 1
M28 01-15 510690 Lip seal 1
M72 01-15 040642 (9003513-0800) Nut 1
M90 01-15 354407 Screw 5
M92 99-06 510382 Screw 1
QM10 01-15 11087610 MDC kit, roller 1
QM83 01-15 001131 (9004201-5000) O-ring 1

Parts Manual
Control
S90P control RU
Parts configuration
QM10
(RR) (RS & RU)
M72 M72
M70 M70
M76
M92
*M27
*M029
*M28
M90 *M26
QM89
*QM83
View A
*M11
M14 View “A”
T20
T70 (supply) T80
T30
T40

Parts Manual
Control
Order code: RU
Model/Kit
M26 97-30 144725 (9004105-0110) O-ring 1
M27 97-30 042507 (9006300-0044) Retaining ring 1
M28 97-30 510690 Lip seal 1
M72 97-30 040642 (9003513-0800) Nut 1
M90 97-30 354407 Screw 5
M92 99-06 510382 Screw 1
QM10 97-30 11087609 MDC kit, roller 1
QM83 97-30 001131 (9004201-5000) O-ring 1

Parts Manual
Control
S90P control SA-SE

Parts configuration
M90
View A
M11
View“A”
M14
T70 T80

Parts Manual
Control
Order code: SA
Model/Kit
M11 07-23 8800923 Gasket 1
M14 07-23 11070305 Feedback link 1
M90 07-23 694356 (9007314-0608) Screw 6
Order code: SB
M11 07-23 8800923 Gasket 1
M14 07-23 11070305 Feedback link 1
M90 07-23 694356 (9007314-0608) Screw 6
Order code: SD
M11 10-34 8800923 Gasket 1
M14 10-34 11070305 Feedback link 1
M90 10-34 694356 (9007314-0608) Screw 6
Order code: SE
M11 10-34 8800923 Gasket 1
M14 10-34 11070305 Feedback link 1
M90 10-34 694356 (9007314-0608) Screw 6

Parts Manual
Control
S90P control SC
Parts configuration
M29
QM10
M76
*QM031
M90
View A
*M11
View “A”
T70 T50
(servo feed) (drain)
T80
(servo feed)
T20
(supply)
T30
T40

Parts Manual
Control
Order code: SC
Model/Kit
M11 98-21 8800923 Gasket 1
M29 98-21 035592 Screw 4
M76 98-21 509848/P Solenoid valve, 12 volt 1
M90 98-21 693341 (9007314-0606) Screw 6
QM10 98-21 11098762 Control kit, 3-position, 12 volt 1
QM031 98-21 11099647 Valve seal kit 1

Parts Manual
Filtration
S90P 75cc filtration 3-J

Parts configuration
(3 & L)
(6)
QN01
N01
QN40
QN40
N20 N35 N20

N35
N35 *N15 *N15
N36
N36
N36
N32
(E & P)
QN01
QN40
N20
N35
N35 *N15
N36
N36
(J)
N70
N75 N01
(G)
N71
N97N41 N90
N01 N80
N97
N98 N43
N43
N20
N42 N95 N98
N30
QN40
N42 N20
N95 QN40
N60
N30
* included in base pump seal kit Q210

Parts Manual
Filtration
Order code: 3
Model/Kit
N15 99-18 001172 (9004201-9000) O-ring 1
N20 99-18 11049997 Nut 1
N35 99-18 140644 (9005100-5600) Plug assembly 1
N36 99-18 140644 (9005100-5600) Plug assembly 1
QN01 99-18 11145249 Filter manifold kit 1
QN40 99-18 11004919 Filter, long 1
Order code: 6
N01 00-01 11060345 Filter manifold assembly 1
N15 00-01 001172 (9004201-9000) O-ring 1
N20 00-01 11049997 Nut 1
N32 00-01 140644 (9005100-5600) Plug assembly 1
N35 00-01 140644 (9005100-5600) Plug assembly 1
N36 00-01 140644 (9005100-5600) Plug assembly 1
QN40 00-01 11004917 Filter, short 1
Order code: E
N15 96-46 001172 (9004201-9000) O-ring 1
N20 96-46 360768 Check valve 1
N35 96-46 140644 (9005100-5600) Plug assembly 1
N36 96-49 140644 (9005100-5600) Plug assembly 1
QN40 96-46 11004917 Filter, short 1
Order code: G & J

N20 96-46 360768 Check valve 1
N30 96-46 365965 Plug assembly 1
N42 96-46 140644 (9005100-5600) Plug assembly 1
N43 96-46 140644 (9005100-5600) Plug assembly 1
N95 96-46 500115 Washer 2
N97 96-46 376269 Screw 4
N98 96-46 9004104-0320 O-ring 1
QN40 96-46 11004917 Filter, short 1

Parts Manual
Filtration
S90P 75cc filtration L, P

Parts configuration
(3 & L)
(6)
QN01
N01
QN40
QN40
N20 N35 N20

N35
N35 *N15 *N15
N36
N36
N36
N32
(E & P)
QN01
QN40
N20
N35
N35 *N15
N36
N36
(J)
N70
N75 N01
(G)
N71
N97N41 N90
N01 N80
N97
N98 N43
N43
N20
N42 N95 N98
N30
QN40
N42 N20
N95 QN40
N60
N30

Parts Manual
Filtration
Order code: L
Model/Kit
N15 87-02 001172 O-ring 1
N20 95-18 11049997 Nut (SB-1994-36 on page 323) 1
N20 87-02 95-17 700492 (9002863-1600) Nut 1
N35 87-02 140644 (9005100-5600) Plug assembly 1
N36 87-02 140644 (9005100-5600) Plug assembly 1
QN40 87-02 11004919 Filter, long 1
Order code: P
N15 87-02 001172 (9004201-9000) O-ring 1
N20 95-18 11049997 Nut (SB-1994-36 on page 323) 1
N20 87-02 95-17 700492 (9002863-1600) Nut 1
N35 87-02 140644 (9005100-5600) Plug assembly 1
N36 87-02 140644 (9005100-5600) Plug assembly 1
QN40 87-02 11004917 Filter, short 1

Parts Manual
Filtration
S90P 75cc filtration R-X

Parts configuration
(R)
(S)
N01
N37 *N15
N20
*N15
N36 N10
(X)
(U)
N01
N01
N40
N20
*N15 N20
N45 N36 N35 *N15

N36

Parts Manual
Filtration
Order code: R
Model/Kit
N15 87-02 001172 (9004201-9000) O-ring 1
N20 95-18 11049997 Nut (SB-1994-36 on page 323) 1
N20 87-02 95-17 700492 (9002863-1600) Nut 1
N36 87-02 140644 (9005100-5600) Plug assembly 1
Order code: S
N10 87-02 707554 (5000230) Reducer assembly 1
N15 87-02 001172 (9004201-9000) O-ring 1
N37 87-02 140644 (9005100-5600) Plug assembly 1
Order code: U
N15 96-16 001172 (9004201-9000) O-ring 1
N20 96-16 11049997 Nut 1
N41 96-16 8700127 Diagnostic receptacle 1
N45 96-16 8700128 Dust cover 1
Order code: X
N15 01-01 001172 (9004201-9000) O-ring 1
N20 01-01 11049997 Nut 1
N25 01-01 700302 (8800180) Tube 1
N35 01-01 9005100-5600 Plug assembly 1
N36 01-01 9005100-5600 Plug assembly 1
QN40 01-01 11004919 Filter, long 1

Parts Manual
S90 75cc pump high pressure regulation 1-7

Parts configuration
P80
P80 P80
P80
P80 P70
P70 P70
P80
P80 P70 P70
View “A” of end cap
View “A” of end cap View “A” of end cap without pressure limiters,
with pressure limiters, with pressure limiters, CCW and CW pump rotation.
CCW pump rotation. CW pump rotation. Options 2 and 7
Options 1, 5, 6 and F Options 1, 5, 6 and F
QPA2B
P80 (1, 2, 4, 5, 6, 7, B, D, F)
P70
View “A”
QPA2A *P02
P80 P80
View “A” of end cap *P06
with pressure limiter port A, *P13
CW pump rotation.
*P02
Option B
*P06
QPA2B *P13
(A)
QPA2A
*P02
*P06
*P13
*P02
*P06
*P13
Generic end cap used to show valve location only.

Parts Manual
Common parts
Model/Kit
P02 87-02 688721 (9004104-0170) O-ring 2
P06 87-02 071811 O-ring 2
P13 87-02 544742 (9004105-0190) O-ring 2
Order code: 1
P70 87-02 8800188 Check valve 2
P80 87-02 9005475-004 Special plug assembly 2
QPA2A 87-02 8510022-1 Multi-function valve kit 1
QPA2B 87-02 8510022-1 Multi-function valve kit 1
Order code: 2
P70 87-02 327007 (9005110-4400) Plug (SB-1989-003 on page 306) 1
APA2B 87-02 8510022-2 Multi-function valve kit 1
Order code: 4
Order code: 5
P70 87-02 8800188 Check valve 2
QPA2A 87-02 8510240 Multi-function valve kit 1
QPA2B 87-02 8510240 Multi-function valve kit 1
Order code: 6
P70 87-02 8800188 Check valve 2
Order code: 7
P70 87-02 327007 (9005110-4400) Plug (SB-1989-003 on page 306) 1

Parts Manual
S90P 75cc high pressure regulation A-F

Parts configuration
P80
P80 P80
P80
P80 P70
P70 P70
P80
P80 P70 P70
View “A” of end cap View “A” of end cap without pressure limiters,
with pressure limiters, with pressure limiters, CCW and CW pump rotation.
CCW pump rotation. CW pump rotation. Options 2 and 7
Options 1, 5, 6 and F Options 1, 5, 6 and F
QPA2B
P80 (1, 2, 4, 5, 6, 7, B, D, F)
P70
View “A”
QPA2A *P02
P80 P80
with pressure limiter port A, *P13
CW pump rotation.
*P02
Option B
*P06
QPA2B *P13
(A)
QPA2A
*P02
*P06
*P13
*P02
*P06
*P13

Parts Manual
Common parts
Model/Kit
P02 87-02 688721 (9004104-0170) O-ring 2
P06 87-02 071811 O-ring 2
P13 87-02 544742 (9004105-0190) O-ring 2
Order code: A
QPA2A 87-02 8510202 Multi-function valve kit, 420 bar 1
QP2AB 87-02 8510202 Multi-function valve kit, 420 bar 1
Order code: B
P70 95-22 8800188 Check valve 1
Order code: D
QPA2A 92-39 8510388 Multi-function valve kit, 420 bar 1
QP2AB 92-39 8510388 Multi-function valve kit, 420 bar 1
Order code: F
P70 04-36 8800188 Check valve 2

Parts Manual
S90P 75cc high pressure regulation G-M

Parts configuration
P80
P80
P80 P70
P70 P70
P80 P70
P70 P70
View “A” of end cap View “A” of end cap View “A” of end cap
with pressure limiters, with pressure limiters, without pressure limiters,
CCW pump rotation. CW pump rotation. CCW and CW pump rotation.
Options G & H Options G & H Options M
QPA2B
View “A”
*P02
QPA2A (G & M)
*P06
*P13
*P02
*P06
*P13
QPA2B
QPA2A
QPA2B
(H)
(J) *P02 View “A”
*P21
*P20
*P21
*P20 *P06
*P13
*P02
*P02
*P21 *P06
*P20 *P13
*P06
*P13
*P02
QPA2A *P06
*P13

Parts Manual
Common parts
Model/Kit
P02 87-02 688721 (9004104-0170) O-ring 2
P06 87-02 071811 O-ring 2
P13 87-02 544742 (9004105-0190) O-ring 2
Order code: G
P70 97-06 8800188 Check valve 2
P80 97-06 9005475-0004 Special plug 2
Order code: H
P20 97-40 9004105-0160 O-ring 1
P21 97-40 9006110-0160 Backup O-ring 1
P70 97-40 8800188 Check valve 2
P80 97-40 9005475-0004 Special plug 2
Order code: J
P20 97-06 9004105-0160 O-ring 2
P21 97-06 9006110-0160 Backup O-ring 2
Order code: M
P70 98-11 8800188 Check valve 2

Parts Manual
S90P 75cc high pressure regulation N, P

Parts configuration
P70
P70N
P80 P80
P80 P80
P70N P80
P80
P70
with pressure limiter port B, View “A” of end cap
CCW pump rotation. with pressure limiter port B,
Option N CW pump rotation.
Option N
P70 P80
P80
P70
P80
P80
P70 P70
View “A” of end cap View “A” of end cap
with pressure limiters, with pressure limiters,
CCW pump rotation. CW pump rotation.
Options P Options P
QPA2B
(N & P)
*P02 View “A”
QPA2A
*P06
*P13
*P02
*P06
*P13

Parts Manual
Common parts
Model/Kit
P02 87-02 688721 (9004104-0170) O-ring 2
P06 87-02 071811 O-ring 2
P13 87-02 544742 (9004105-0190) O-ring 2
Order code: N
P70 98-41 8800188 Check valve 1
P70N 98-41 327007 (9005110-4400) Plug assembly 1
P80 98-41 9005475-0004 Special plug 3
PA2A 98-41 781971 Plug assembly 1
Order code: P
P70 99-26 8800188 Check valve 2
P80 99-26 9005475-0004 Special plug 2

Parts Manual
S90P 75cc high pressure regulation R, S

Parts configuration
P70
P70N
P80 P80
P80
P70 P80
P80 P80 P70N

(R)
with pressure limiter port A, PA2B with pressure limiter port A,
*P06
View “A”
QPA2A
*P13
*P02
*P06
*P13
QPA2B
(S)
*P02 View “A”
QPA2A
*P06
*P13 P70
*P02
P70
*P06
*P13 View “A” of end cap
with pressure limiters

Parts Manual
Common parts
Model/Kit
P02 87-02 688721 (9004104-0170) O-ring 2
P06 87-02 071811 O-ring 2
P13 87-02 544742 (9004105-0190) O-ring 2
Order code: R
P70 99-14 8800188 Check valve 1
P70N 99-14 327007 (9005110-4400) Plug assembly 1
P80 99-14 9005475-0004 Special plug 3
PA2A 99-14 781971 Plug assembly 1
Order code: S
P70 02-23 8800188 Check valve 2

Parts Manual
S90P 75cc high pressure regulation U, W

Parts configuration
(U)
P70 P80
P80
P70
P80
P80 QPA2B
P70 View “A” P70
*P02 View “A” of end cap
CCW pump rotation. *P06 CW pump rotation.
*P13
*P02
*P06
QPA2A *P13
(W)
QPA2B
P80
*P02 View “A”
P70
QPA2A
*P06
P80 P80 *P13

with pressure limiter port A,
CW pump rotation.
*P06
*P13

Parts Manual
Common parts
Model/Kit
P02 87-02 688721 (9004104-0170) O-ring 2
P06 87-02 071811 O-ring 2
P13 87-02 544742 (9004105-0190) O-ring 2
Order code: U
P70 04-36 8800188 Check valve 2
P80 04-36 9005475-0004 Special plug 2
Order code: W
P70 09-50 8800188 Check valve 1
P80 09-50 9005475-0004 Special plug 3

Parts Manual
S90P 75cc high pressure regulation X, Y

Parts configuration
P70 P80
P80
P70
P80
P80
P70 P70
QPA2B
*P21
*P20
(X)
QPA2A *P02 View “A”

*P21
*P20
*P06
*P13
*P02
*P06
*P13
QPA2B
*P21
*P20
(Y)
*P02 View “A”
*P06
*P13
*P02
QPA2A
*P06
*P13

Parts Manual
Common parts
Model/Kit
P02 87-02 688721 (9004104-0170) O-ring 2
P06 87-02 071811 O-ring 2
P13 87-02 544742 (9004105-0190) O-ring 2
Order code: X
P20 09-19 9004105-0160 O-ring 2
P21 09-19 9006110-0160 Backup O-ring 2
P70 09-19 8800188 Check valve 2
P80 09-19 9005475-0004 Special plug 2
Order code: Y
P20 11-02 9004105-0160 O-ring 1
P21 11-02 9006110-0160 Backup O-ring 1
P70 11-02 8800188 Check valve 2
P80 11-02 9005475-0004 Special plug 2

Parts Manual
Orifice
S90P 75cc orifice 01-24

Parts configuration
(01, 02, 03, 04, 05,

06, 09 & 22)
T20
T30
T40
(21)
T70 T80
T20
T30
T40
(23 & 24)

T50 T60
T20
T30
T40
See control housing for orifice locations.

Parts Manual
Orifice
Common parts (excluding order code 00)

Model/Kit
T30 87-42 679506 (8700007) Spring 1
T40 87-42 8801303 Spring retainer 1
Order code: 00
No parts
Order code: 01
T20 87-42 8801136 Orificed check valve, .018” 1
Order code: 02
Order code: 03
Order code: 04
Order code: 05
Order code: 06
Order code: 09
Order code: 21
T70 87-42 714477 Orifice plug, 0.8mm, M8 x 8 1
Order code: 22

Parts Manual
Orifice
Parts configuration
(01, 02, 03, 04, 05,

06, 09 & 22)
T20
T30
T40
(21)
T70 T80
T20
T30
T40
(23 & 24)

T50 T60
T20
T30
T40
See control housing for orifice locations.

Parts Manual
Orifice

Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: 23
Order code: 24

Parts Manual
Orifice

Parts configuration
(25, 28, 30 & 35)

T50 T70 T80 T60
T20
T30
T40
(26 & 29)

T50 T60
T20
T30
T40
(32) (34)
T50 T60 T70 T80
See control drawing for orifice location.

Parts Manual
Orifice
Common parts (excludes order codes 32-34)

Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: 25
Order code: 26
T50 87-42 598292 (11062004) Orifice plug, 0.8mm, M5 x 6 1
Order code: 28
Order code: 29
Order code: 30
Order code: 32

Parts Manual
Orifice
Parts configuration
(25, 28, 30 & 35)

T50 T70 T80 T60
T20
T30
T40
(26 & 29)

T50 T60
T20
T30
T40
(32) (34)
T50 T60 T70 T80

Parts Manual
Orifice
Common parts (excludes order codes 32-34)

Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: 33
No parts
Order code: 34
Order code: 35
T60 87-42 639120 Orifice plug, 1.0mm, M5 x 6

Parts Manual
Orifice

Parts configuration
(38 & 42) (41)

T70 T80 T50 T70 T80 T60
T20
T30
T40
(43)
T50 T70 T80 T60

T20
T30
T40
(45, 46 & 49)

T50 T60
T20
T30
T40

Parts Manual
Orifice

Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: 38
Order code: 41
Order code: 42
Order code: 43
Order code: 45
Order code: 46
Order code: 49

Parts Manual
Orifice

Parts configuration
(50 & 52) (60)

T50 T70 T80
T50 T60
T20
T20
T30
T30
T40
T40
(64) (71)
T50 T60 T20
(73, 74) (76)

T50 T70 T80 T70 T80
T20 T60
T20
T30 T30
T40 T40

Parts Manual
Orifice
Common parts (excluding order codes 64 & 71)

Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: 550

Order code: 52
T20 87-42 11061970 Orificed check valve, 1.02mm 1
Order code: 60
Order code: 64
Order code: 71
T20 87-42 11061957 Orificed plug, 0.79mm 1
Order code: 73

Parts Manual
Orifice
Parts configuration
(50 & 52) (60)

T50 T70 T80
T50 T60
T20
T20
T30
T30
T40
T40
(64) (71)
T50 T60 T20
(73, 74) (76)

T50 T70 T80 T70 T80
T20 T60
T20
T30 T30
T40 T40

Parts Manual
Orifice
Common parts (excluding order codes 64 & 71)

Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: 74
Order code: 76

Parts Manual
Orifice
S90P 75cc orifice 78-A7

Parts configuration
(78, 99, A5, A6 & A7) (82, A2 & A4)
T70 T80 T70 T80

T20
T30
T40
(84)
(A3)
T50 T70 T80 T50 T60
T20
T30
T40

Parts Manual
Orifice
Common parts (excluding 82, 84, A2 & A4)

Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: 78
Order code: 82
Order code: 84
Order code: 99
T30 87-42 679506 (8700007) Spring 1
Order code: A2
Order code: A3
T30 87-42 679506 (8700007) Spring 1
Order code: A4

Parts Manual
Orifice
Parts configuration
(78, 99, A5, A6 & A7) (82, A2 & A4)
T70 T80 T70 T80

T20
T30
T40
(84)
(A3)
T50 T70 T80 T50 T60
T20
T30
T40

Parts Manual
Orifice
Common parts (excluding 82, 84, A2 & A4)

Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: A5
T20 87-42 11061970 Orificed check valve, 0.40” 1
T30 87-42 679506 (8700007) Spring 1
Order code: A6
T30 87-42 679506 (8700007) Spring 1
Order code: A7
T30 87-42 679506 (8700007) Spring 1

Parts Manual
Orifice
S90P 75cc orifice A8-C4

Parts configuration
(A8, A9 & C1) (B1, B7, B8 & B9) (B2)

T70 T80 T50
T20 T70 T80
T30
T40
(B3) (B2)
T70 T80
T20
T50 T70 T80
T30
T40
(C2 & C3) (C4)

T50 T60
T20 T50 T60
T30
T40

Parts Manual
Orifice
Order code: A8
Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: A9
T20 87-42 11061993 Orificed check valve, 1.57mm 1
T30 87-42 679506 (8700007) Spring 1
Order code: B1
T50 87-42 507042 Orifice plug, 1.5 mm, M6 x 8 1
Order code: B2
Order code: B3
Order code: B6
No parts
Order code: B7
Order code: B8
Order code: B9

Parts Manual
Orifice
Parts configuration
(A8, A9 & C1) (B1, B7, B8 & B9) (B2)

T70 T80 T50
T20 T70 T80
T30
T40
(B3) (B2)
T70 T80
T20
T50 T70 T80
T30
T40
(C2 & C3) (C4)

T50 T60
T20 T50 T60
T30
T40

Parts Manual
Orifice
Order code: C1
Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: C2
T30 87-42 679506 (8700007) Spring 1
Order code: C3
T30 87-42 679506 (8700007) Spring 1
Order code: C4

Parts Manual
Orifice
S90P 75cc orifice C5-G8

Parts configuration
(C5, C6, C7 & C9) (C8)

T60 T90 T95
T50
T20 T20
T30 T30
T40 T40
(D2) (G1) (G4 & G8)
T70 T80
T50 T50
T20
T20
T30
T30
T40
T40

Parts Manual
Orifice
Common parts (excluding order code G1)

Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: C5
Order code: C6
Order code: C7
T20 87-42 11061981 Orificed check valve, 1.37 mm 1
Order code: C8
T90 87-42 704650 (1162018) Orifice plug, 0.7 mm, M8 x 8 1
Order code: C9
Order code: D2
Order code: D4

Parts Manual
Orifice
Parts configuration
(C5, C6, C7 & C9) (C8)

T60 T90 T95
T50
T20 T20
T30 T30
T40 T40
(D2) (G1) (G4 & G8)
T70 T80
T50 T50
T20
T20
T30
T30
T40
T40

Parts Manual
Orifice
Common parts (excluding order code G1)

Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: G1
Order code: G4

Parts Manual
Orifice
S90P 75cc orifice G8-P1

Parts configuration
(GB, GD, GF & GJ) (H1, H9 & K2)

T50 T60
T50
T20 T20
T30 T30
T40 T40
(K1) (P1)
T70 T80
T20
T30
T40

Parts Manual
Orifice
Common parts (excluding order code P1)

Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: G8
Order code: GB
Order code: GD
T20 87-42 11061993 Control orifice kit, 1.57 mm 1
Order code: GF
T20 87-42 11061970 Control orifice kit, 0.040” 1
Order code: GJ
T20 87-42 11061981 Control orifice kit, 1.37 mm 1
Order code: H1
Order code: H9
Order code: K1

Parts Manual
Orifice
Parts configuration
(GB, GD, GF & GJ) (H1, H9 & K2)

T50 T60
T50
T20 T20
T30 T30
T40 T40
(K1) (P1)
T70 T80
T20
T30
T40

Parts Manual
Orifice
Common parts (excluding order code P1)

Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: K2
Order code: P1

Parts Manual
Orifice
S90P 75cc orifice Z1, Z3

Parts configuration
T70 T80
T20
T30
T40

Parts Manual
Orifice
Order code: Z1
Model/Kit
T30 87-42 679506 (8700007) Spring 1
Order code: Z3
T30 87-42 679506 (8700007) Spring 1

Parts Manual
overhaul seal kit
S90 75cc pump overhaul seal kit
Overhaul seal kit

Model/Kit
Q210 87-42 11095648 Overhaul seal kit 1
B90 87-42 9803390 Control screen 3
E40 87-02 505412 (9003509-0008) Seal nut 2
E60 87-02 517228 (5000206) Screw (SB-1994-018) 6
F112 87-02 505412 (9003509-0008) Seal nut 1
F212 87-02 505412 (9003509-0008) Seal nut 1
G30 92-19 8100565 End cap gasket 1
J50 87-02 056739 (9004104-1580) O-ring 1

Parts Manual
Service bulletin
SB-1988-009
Products affected
Series 90 pumps
Subject
Servo arm change
Description
As a product improvement, Danfoss has changed the series 90 pump servo arm and swashplate (item
D10 and D50). The old style servo arm and swashplate will become obsolete. Because this change creates
non-interchangeability between new and old swashplates, servo arms, and possibly servo piston (item
S10) and slider block (item F20), separate servo arms and swashplates will no longer be sold as service
parts.
Also, the new servo arm is pressed into a groove in the new swashplate. This situation requires special
tooling for assembly, therefore, pre-assembled kits will be created for 55, 75, and 100 cc pumps. The kits
will work in any vintage pump.
The kit for 55 cc pumps will include all the items in the figure, except item S10
The kit for 75 cc pumps will include all items in the figure.
The kit for 100 cc pumps will include all items in the figure, except items S10 and F20.
The slider block (item F20) in 55 cc pumps and the slider block and the servo piston (item S10) in 75 cc
pumps had to be changed slightly to allow clearance for the new servo arm. The new servo piston and
slider block will work in any vintage pump.
D55 D65
S10
F12 F11 D10

D75 D60
F11 D70
F12
F20
D50
Models affected
All 94-2xxx (55 cc), 95-2xxx (75 cc), and 96-2xxx (100 cc) pumps
Serial numbers
Change goes into effect with s/n 88-14-xxxxx on 55 cc pumps and with s/n 88-16-xxxxx for 75 cc and 100
cc pumps

Parts Manual
Service bulletin
Part numbers affected

• New 55 cc slider block is p/n 8000189
• New 55 cc servo arm/swashplate kit is p/n 8000201
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-1988-016
Products affected
Series 90 pumps
Subject
Change to fix clearance slipper hold down.
Description
As a product improvement, Danfoss has simplified the design of the series 90 pump slipper hold down
mechanism. The hold down changes from spring loaded with a fixed maximum clearance design.
The leaf spring (item C60) and spring aligner (item C66) will be eliminated and will not be available as
service parts. The spacer (item C50), bearing (item C40), and washer (item C65) will change and the old
part numbers will not be available as service parts. The swashplate (item D50), pistons (item C20), slipper
retainer (item C30), and screws (item C70) will remain the same.
If any of the affected parts (item C66, C60, C65, C50, or C40) require replacement during repair of older
style pumps, discard these parts and rebuild using new style parts (items C40, C50, and C65). As before,
the screws (item C70) which are coated with locking compound MUST always be replaced after removal.
C40
C50
C65
C60
C66
C70 C20
C30
D50
C50
C40
C65
Old Style C70
Slipper Hold-Down
New Style
Slipper Hold-Down
Models affected
Serial numbers
• 55 cc pumps, 94-2xxx, changed at s/n 88-43-xxxxx
• 75 cc pumps, 95-2xxx, changed at s/n 88-22-xxxxx
• 100cc pumps, 96-2xxx, changed at s/n 88-20-xxxxx
Item Qty/pump 55cc 75cc 100cc

C40 2 8000137 8100294 8200144
C50 4 8000138 8100295 8200145

Parts Manual
Service bulletin
Item Qty/pump 55cc 75cc 100cc

C65 4 9009625-0159 9009625-0159 9009625-0159
C70 4 314419 9007276-0099 9007276-0099
(9007276-0114)
Parts disposition
Non-interchangeable as individual parts, but new style C40, C50, and C65 can be used in any vintage
pump, if all three are changed.

Parts Manual
Service bulletin
SB-1988-023
Products affected
Series 90 pumps and motors
Subject
Piston improvement
Description
Product Information Bulletin PIB-8801 (March, 1988) announced the incorporation of fabricated (welded)
piston assemblies, replacing non-fabricated (hollow) piston assemblies, in the cylinder blocks of all Series
90 pumps and motors. This change increases the overall efficiency of the Series 90 product line.
To simplify service parts inventory for all Series 90 units, only individual welded piston assemblies will be
available as spare parts. The hollow pistons will be obsoleted. Part numbers for individual welded piston
assemblies are listed in this bulletin.
Since all Series 90 pumps and motors have nine (9) pistons, welded pistons being used to replace hollow
pistons during repair MUST be install in the cylinder block symmetrically, in multiples of three (3).
Welded Piston Hollow Piston

Assembly Assembly
When replacing hollow pistons with welded pistons, it is mandatory that the welded pistons be
incorporated symmetrically in multiples of three.
Models affected
All series 90 pumps and motors: 93-xxxx, 94-xxxx, 95-xxxx, and 96-xxxx pumps
Serial numbers
Welded pistons will be incorporated into all series 90 pumps and motors by the end of the first quarter of
1998.
Part number Description

706101 Piston assembly, welded - 42 cc

Parts Manual
Service bulletin
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1989-002
Products affected
Series 90 pumps
Subject
Incorporation of adjustable charge relief valve
Description
As a product improvement Danfoss is incorporating an adjustable charge relief valve on all series 90
variable displacement pumps. This design replaces the previous shim adjustable charge relief valve. The
new design valve provides a range of pressure adjustment which covers the available charge pressure
options of 290, 348, and 406 psi [20, 24, and 28 bar].
This improvement changes the design of the charge relief valve poppet and plug. The new style charge
relief may protrude from the pump end cap approximately 0.27 in [6.9 mm] farther than the adjustable
relief valve.
To adjust the new design valve, first install a gauge to measure charge pressure as described in the series
90 service manual. Loosen the adjustment lock nut with a 1-1/16 in hex wrench. Operate the pump at an
input speed of 1700 to 2000 rpm and turn the adjustment plug with a large screwdriver while observing
the charge pressure. Clockwise rotation of the plug increases the setting, while counterclockwise rotation
decreases the setting at a rate of approximately 50 psi [3.4 bar] per turn. Once the desired setting is
achieved, torque the lock nut to 34-41 lbf·ft [46-55 Nm], and remove the charge pressure gauge.
Danfoss will offer an adjustable charge relief valve kit for sale as a service part. This kit can be used to
service any vintage series 90 variable pump. Since the new and old style charge relief valves are
interchangeable as an assembly, the old style parts will no longer be available as service parts.
Models affected
All 93-2xxx, 94-2xxx, 95-2xxx, and 96-2xxx pumps
Part number Description

8002K000-A Adjustable charge relief valve kit - new style (includes
poppet, spring, plug, O-ring, and nut)
Parts disposition
Interchangeable (as an assembly)
SB-1989-003
Products affected
Series 90 pumps
Subject
Swashplate leveler spring seat change and servo pressure relief valve deletion

Parts Manual
Service bulletin
Description
As a product improvement, Danfoss is adding hardened shims between the swashplate leveler springs
and the end cap in series 90 variable pumps. In addition, the leveler spring seats have been hardened,
and are now separate pieces from the leveler. Previously, the seats were peened to the leveler.
These improvements require some minor changes in the repair procedures for the series 90 pumps.
When installing the lever springs (E80), take care that the spring seats (E22) are in position on the
swashplate leveler (E20). Before installing the end cap, assemble the hardened shims (E24) into their
pockets in the end cap and retain with petroleum jelly.
In an unrelated change, the servo pressure check relief valves installed in the pump end cap (or rotation
valve housing) are no longer required. These valves (P70) will be replaced by standard socket head,
straight thread O-ring plugs.
The swashplate leveler, plus the separate spring seats, are directly interchangeable with the old design
part. When performing major repairs on any series 90 pump, the hardened shims should be installed
between the leveler springs and the end cap. The plugs are also interchangeable with the servo pressure
check relief valves.
End Cap
E22
E80 E20
E22
E24 E80
E24
P80
P70
Models affected
All 93-2xxx (42 cc), 94-2xxx (55 cc), 95-2xxx (75 cc), and 96-2xxx (100 cc) pumps
Serial numbers
The hardened swashplate leveler spring seats and hardened shims incorporated at serial number 89-09-
xxxxx. Due to the interchangeability of the straight thread plugs with the servo pressure check relief
valves, this change will be incorporated during the 1st quarter of 1989.
Item Description Qty 42cc 55cc 75cc 100cc

E20 Leveler 1 673897 8000094 8100130 8200007
E22 Spring seat 2 358820 358838 358523 358846
E24 Shim 2 359034 359042 359042 359059
P70 Plug 2 9005110-4400 9005110-4400 9005110-4400 9005110-4400
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-1989-006
Products affected
Series 90 pumps
Subject
Charge pump design change
Description
The original series 90 charge pump design included two (2) port plates, one (1) on each side of the
gerotor. If the charge pump displacement was less than the maximum available for the pump’s frame
size, the inside port plate was thicker than the 0.050 in. (1.27 mm) outside port plate.
The new design charge pump will always have two (2) 0.050 in (1.27 mm) thickness port plates, one (1) on
each side of the gerotor. Additionally, if the charge pump displacement is less than the maximum
available for the pump’s frame size, one (1) or two (2) spacers were install between the outside port plate
and the charge pump cover.
In addition, the location of the keyway in the change pump shaft has been changed to ensure full
engagement of the drive key in the gerotor. The new charge pump shaft used in 75 and 100 cc pumps
has two (2) keyways. The rear keyway (farthest from the end cap and splined end of the shaft) is used for
75 cc pumps, while the front keyway is used for 100 cc pumps. The new style charge pump shafts for 55,
75, and 100 cc pumps also changed from having a beveled end to a square end on the end closest to the
pump end cap.
Drive key Drive key

Charge pump shaft
Charge pump shaft
Inner Port Plate
Inner Port Plate
Gerotor
Outer Port Plate Gerotor
Outer Port Plate
Spacer
Charge Pump
Charge Pump
Cover Identifying groove for
2nd Spacer
(used only with 17 cc/rev 75 cc keyway
for 100 cc pump) 75 cc keyway
Note beveled Note square

100 cc keyway
end end
Old charge pump shaft New charge pump
shaft for 75 cc and
100 cc pumps
Models affected

Parts Manual
Service bulletin
Serial numbers
• A-89-17-xxxxx for all pumps manufactured in Ames, Iowa.
• N-89-07-xxxxx for all 95-2xxx (75 cc) pumps manufacture in Neumunster, West Germany.
• N-88-48-xxxxx for all 96-2xxx (100 cc) pumps manufacture in Neumunster, West Germany.

Proper part number versus pump serial number information can be found in the series 90 Parts Manuals.
The thicker inside port plates (thicker than 0.050 in (1.27 mm) will be obsoleted and no longer available
as service parts. If these parts require replacement, use the 0.050 in. 1.27 mm) port plate and appropriate
spacer(s) as service parts. On 100 cc pumps only, the new charge pump shaft must be used if the new
style spacer is used on 55 and 75 cc pumps, the change pump shaft clearance pocket in the end cap
changed from a beveled to a straight corner to correspond with the change in the charge pump shaft.
Old style charge pump shafts will remain available as service parts and must be used in the 55 and 75 cc
beveled pocket end caps.
Old style (beveled pocket) end caps will be obsoleted and no longer available as service parts. If an old
style end cap needs replacement, new style end caps can be used with any vintage charge pump
hardware and charge pump shaft.
Parts disposition
Non-interchangeable- must use correct charge pump shaft per serial number of pump

Parts Manual
Service bulletin
SB-1989-023
Products affected
Series 90 100cc variable pumps
Subject
Reduction in overall length
Description
To improve application flexibility, the overall length of series 90 100 cc pumps will be reduced by .39” [10
mm]. Some port locations will also change.
Shown below are all dimensional differences between the current and new design pumps.
E
To Split
Flange
Port "A"
C
Charge Pump
Inlet
B
Charge Pump
Inlet
Dim Old New

A 11.22” [285 mm] 10.94” [277.9 mm]
B 11.73” [297.9 mm] 11.34” [288 mm]
C 3.64” [92.5 mm] 3.53” [89.7 mm]
D* 13.73” [348.7 mm] 13.34” [338.8 mm]
E 3.87” [98.3 mm] 3.75” [95.3 mm]
* All dimensions from the mounting face to an auxiliary pump will also be reduced by .39" [10 mm].
Models affected
All 96-2xxx variable pumps
Serial numbers
This change will take place at the serial number A-89-46-xxxxx

Parts Manual
Service bulletin

Non-interchangeability will exist with drive shafts, which become shorter with this change,end caps, end
cap gaskets, and the end cap to the variable housing retaining screws. Old style end caps will no longer
be available as service parts. In the rare event that a new end cap is required, a new shaft, end cap gasket
and screws will also be needed. The new part numbers are as follows:
Item Part number Description Quantity

G04 8200175 End cap, side port 1
G30 8200166 Gasket 1
G90 9007210-0608 Screw 1
G95 9007210-0608 Screw 1
J80 9007314-1623 Screw 4
J80N 9007210-1621 Screw 4
L100 8200169 Shaft, 23 tooth spline 1
L100 8200173 Shaft, tapered 1
L100 8200176 Shaft, straight key 1
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-1992-003
Products affected
Series 90: 55, 75,100.130 cc pumps
Subject
Block point change: components redesign
Description
As part of our overall series 90 product improvement program, numerous components are being
redesigned. This redesign is referred to as a “block point” change. The objective of the block point
change is to minimize the number of times we change the units while we convert to high volume tooling
at various plant sites. These design improvements will provide increased reliability and more application
flexibility. The nature of these changes makes customer re-qualification unnecessary. Old style (pre-block
point) variable housings and end caps will no longer be available as spare parts.
Models affected
All series 90 94-2xxx, 95-2xxx, 96-2xxx, and 97-2xxx variable pumps
Serial numbers
Changes will take place at the serial number 92-12-xxxxx for 100 cc pumps
Housing
Thickness adjacent to the side cover has been increased
Side cover
Thickness increased
End cap
Match housing change; small end cap screws will be larger, orientation of charge relief
valve on side port end caps has been changed from oblique to vertical.
Item Description Old part number New part number

B10 Variable housing 8200117 (O) 726554
E10 Side cover 8200011 748560
F20 Slider block 8200016 (I)(O) 8200225 (I)
G93 Spacer 8800404 8800564
G94 Lifting bracket 8800401 8800565
G95 Washer n/a 9009610-3469
B82 Plug n/a 9005110-5600
B83 Plug n/a 9005110-5600
G048 End cap - twin ports 8200157 (O) 8200235
G308 End cap gasket 8200166 8200212
G908 Screw 9007210-0608 9007314-0810
G958 Screw 9007314-0608 9007314-0810
G968 Screw 9007314-0607 9007314-0808
G046 End cap - side ports 8200175 (O) 8200236
G306 End cap gasket 8200166 8200212
G906 Screw 9007314-0608 9007314-0810

Parts Manual
Service bulletin
Item Description Old part number New part number

G956 Screw 9007314-0608 9007314-0810
G968 Screw 9007314-0607 9007314-080
G172 Plug n/a 9005110-4400
G182 Plug n/a 9005110-4400
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-1992-011
Products affected
Series 90 - 055, 075, and 100 frame size pumps
Subject
Feedback link retention
Description
Effective in September of 1992, the feedback link in series 90 pumps will be mechanically retained to the
swashplate. In the past, the link slipped over a specially ground socket head screw and could fall off the
screw during assembly. The screw has changed to include a head to retain the link. The feedback link
does not change.
Special Screw
Control Feedback Link

Swashplate Assembly
Swashplate Guide
Models affected
Serial numbers
Pumps with serial number A-92-38-xxxx and beyond include the new feature.
Frame size Old screw New headed screw

55 & 75 cc 9007276-0109 9007375-0044
100 cc 9007375-0030 9007375-0032
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1993-001
Products affected
Series90 - 55, 75, and 100 cc pumps
Subject
Charge pump design change
Description
The serial numbers mentioned apply only to Ames production units. Neumunster will incorporate the
change in July or August of this year.
To improve efficiency and reliability, the number of parts in series 90 charge pumps is being reduced. The
charge pump design on 55 cc through 100 cc frame sizes is being changed such that the outer port plate
(H30) is an integral part of the charge pump cover (J15) and distance plates are eliminated.
For auxiliary pad options, the new charge pump cover is rotation dependent. The cover will be marked
either left hand (L) or right hand (R). The non-auxiliary pad cover is not rotation dependent.
The charge pump shaft also changes and must be replaced when using the new style hardware. The
complete charge pump assembly can be interchanged with corresponding hardware from 89-17 and
beyond. However, piece parts are not interchangeable. For units prior to 89-17, consult Danfoss.
Models affected Serial numbers

All 94-2xxx, 95-2xxx, and 96-2xxx pumps
Serial numbers
• 55 cc: A-93-10 & beyond
• 75 cc: A-93-10 & beyond
• 100 cc: A93-15 & beyond
55 cc 75 cc 100 cc Item number Description

Before 93-10 After 93-10 Before 93-10 After 93-10 Before 93-15 After 93-15
8000169 8000268 N/A N/A N/A N/A H05 11 cc charge
pump set
8000170 8000269 8100313 8100479 N/A N/A H05 14 cc charge
pump set
8000171 8000270 8100314 8100480 8200158 8200238 H05 17 cc charge
pump set
N/A N/A 8100315 8100481 8200159 8200239 H05 20 cc charge
pump set
N/A N/A N/A N/A 8200160 8200240 H05 26 cc charge
pump set
8800314 N/A 8800314 N/A 8800314 N/A H30 Port plate
N/A Incl. in H05 N/A Incl. in H05 8800315 Incl. in H05 H31 Port plate
8000174 8000267 337956 8100476 337956 8100476 H50 Charge pump
shaft
8800513 8800834 8800513 8800834 8800513 8800834 J15N Charge pump
cover assy.
8800514 See J15L/R 8800514 See J15L/R 8800514 See J15L/R J15 Aux. charge
pump cover

Parts Manual
Service bulletin
55 cc 75 cc 100 cc Item number Description

Before 93-10 After 93-10 Before 93-10 After 93-10 Before 93-15 After 93-15
N/A 8800833 N/A 8800833 N/A 8800833 J15L Aux. L.H. cover
assy.
N/A 8800832 N/A 8800832 N/A 8800832 J15R Aux. R.H. cover
assy.
Piece parts are not interchangeable
Parts disposition
Interchangeable for s/n 89-17-xxxxx and beyond. Piece parts are not interchangeable.

Parts Manual
Service bulletin
CURRENT CHARGE PUMP CONFIGURATION

EXCEPT FOR 100 CC FRAME SIZE PUMPS
CURRENT CHARGE PUMP

CONFIGURATION FOR 100 CC
FRAME SIZE PUMPS
NEW CHARGE PUMP

H60 CONFIGURATION
H50
H40
H30
H05
H60
H50
H05 H40
(H30) (H31)
J80N
H30
OR H60
H50
H40
H05
OR
J40N
J15
J15N J10
H70
H80 J30 L J30
J50
J70
OR
J80
H80
J60 REF
NEW CHARGE PUMP COVER J90 H70
REF
FOR PUMPS WITHOUT AUXILIARY PADS
(SAME COVER FOR LEFT HAND OR J92
RIGHT HAND ROTATION) J
J95
L
NEW CHARGE PUMP COVERS FOR PUMPS WITH AUXILIARY PADS
(LEFT HAND AND RIGHT HAND ROTATION VERSIONS INCLUDED
IN AUXILARY PAD KIT)
THE NEW CHARGE PUMP COVERS HAVE AN 'L' OR 'R'

STAMPED ON THEM FOR EASY IDENTIFICATION

Parts Manual
Service bulletin
SB-1993-015
Products affected
Series 90 pump: all frame sizes
Subject
Servo arm interference with speed sensor ring
Description
This service bulletin revision adds the 42 cc frame size and the incorporation date of 55 through 100 cc.
A potential interference problem has been identified in series 90 42, 55, 75, and 100 cc frame size pumps
built since early 1992. Interference may occur between the swashplate hold down bracket on the servo
arm and the speed sensor ring, which may be installed on the cylinder block as an option.
A new hold down bracket has been designed to provide clearance for the speed sensor ring.
If a cylinder block with speed ring must be installed in one of the subject pumps, a servo arm assembly
with the new hold down will also be required.
Sometime during the first quarter of 1994, all 55, 75, and 100 cc pumps will be equipped with the new
design hold down bracket. The 42 cc pumps will implement the new design hold down bracket in the
second quarter of 1994.
Servo Arm Assembly
Clearance Slot for

Speed Sensor Ring
Swashplate
Models affected
All 93-2xxx, 94-2xxx, 95-2xxx, and 96-2xxx variable pumps
Serial numbers
• 42 cc at serial number 92-16-xxxxx
Frame size Old servo arm (no slot in bracket) New servo arm (with slot in
bracket)
42 cc 354282 502976
55 cc 8000191 8000318
75 cc 8100366 8100499
100 cc 8200182 8200268

Parts Manual
Service bulletin
Parts disposition
Non-interchangeable - Pumps with speed sensor ring must use the new servo arm.

Parts Manual
Service bulletin
SB-1994-017
Products affected
Series 90 55-100cc variable pumps
Subject
Swashplate cage locator
Description
As a product improvement, Danfoss has made a design change to the cage locator link used on the 55
thru 100 cc variable pumps.
The new link is made from square wire. In the past, the link was made from round wire, This is an
interchangeable change.
Cage Locator Link
Models affected
All 94-2xxx + 942xxx, 95-2xxx, + 952xxx and 96-2xxx + 962xxx variable pumps
Serial numbers
• 55and 75 cc pumps serial number 94-18-xxxxx
• 100 cc pumps will begin 4th quarter 1994
Size Old link New link

55cc 8100241 8100506
75cc 8100241 8100506
100cc 8200108 8200273
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1994-018
Products affected
Series 90 variable pumps
Subject
Side cover washer elimination
Description
The washers located under the side cover screws have been removed on all series 90 42 through 130 cc
variable pumps.
As before, the side cover screws must be replaced if they are removed for any reason. The special coating,
which seals and retains the screws, wears off when the screws are removed.
The screw length changed on 55 through 100 cc pumps, so it is important that the washers are discarded
during repair. The proper screw is included in the overhaul seal kits.
Washer - No Longer Used

New Special Screw
Models affected
All 93-2xxx, 94-2xxx, 95-2xxx, 96-2xxx, and 97-2xxx variable pumps
Serial numbers
Change took place during the quarter 2 and 3 of 1994
Pump size Old screw New screw

42 cc 648477 Same part number
55-100 cc 9007276-0115 517228 (5000206)
130 cc 308700 Same part number

Parts Manual
Service bulletin
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1994-36
Products affected
Series 90 55 thru 130 cc variable pumps
Subject
Integral filtration manifold
Description
As a product improvement, Danfoss is changing the integral filter manifold and bulkhead nut to make it
more easily indexed.
The old bulkhead nut may be used with either the old or new filter manifold. The new bulkhead nut can
only be used with the new filter manifold.
The old bulkhead nut will remain available as a service part. The old filter manifold will be obsoleted and
no longer available as a service part.
Old Design
Manifold
Nut
New Design
Manifold
Nut
Models affected
All series 90 55 thru 130 cc variable pumps with “L”, “M”, or “P” filtration option code
Serial numbers
Change occurred at serial number95-18-xxxxx
Description Part number (prior to 95-18) Part number (after 95-18)

Filter manifold 8800200 8800896
Bulkhead nut 9002863-1600 5000222
Parts disposition
Interchangeable- new bulkhead nut can only be used with new filter manifold

Parts Manual
Service bulletin
SB-1995-003
Products affected
Series 90 variable pumps, all frame sizes
Subject
Manual displacement control (MDC) with DC electric solenoid override
Description
In order to accommodate our European customers, the manifold which attaches to the front of the
manual displacement control (MDC) housing is being changed.
The European solenoid valve requires a thicker manifold to provide clearance between the solenoid and
the front of the MDC housing. The revised manifold will protrude closer to the mounting flange of the
pump, reducing dimension“A” shown in the accompanying drawing by approximately 5 mm [0.2 in].
Please see chart below for specific clearances.
The thicker manifold requires longer screws and may be used with either the U.S. or European sourced
solenoid.
This change will become effective during March of 1995. The old manifold will be obsoleted and no
longer available as a service part.
Solenoid valve
Manifold
"A"
"X"
Neutral Start
Switch (NSS)
Option
Top view Series 90 Front view

Manual displacement control View in "X" direction
with DC solenoid override
Frame size 42 55 75 100 130

Dimension "A" Old 39.9 [1.57] 55.9 [2.20] 54.1 [2.31] 60.2 [2.37] 74.4 [2.93]
mm [in]
New 34.9 [1.39] 50.9 [2.0] 49.1 [1.93] 55.2 [2.17] 69.4 [2.73]
Models affected
All series 90 variable pumps using MDC with DC electric solenoid override.
Description Current part number New part number Quantity

Manifold 8800365 505022 1
Screw 9007314-0605 9007314-0606 2
Parts disposition
Interchangeable (new manifold requires longer screws)

Parts Manual
Service bulletin
SB-1995-012
Products affected
Subject
End cap design change
Description
As part of a Series 90 product improvement program, the 75cc twin ported end cap is being redesigned.
The redesign will eliminate the logic block and place the pressure limiter logic area in the same location
as the side ported end cap, which is on the back side of the end cap. The logic pattern will be the same as
the current 75cc side ported end cap. Old style end caps will be obsoleted and no longer available as a
service part.
Any unit with a twin ported end cap and built prior to serial number A-96-05-xxxxx, must use the
8100466 gasket. Any unit with a serial number A-96-05-xxxxx and beyond must use the 8100565 gasket.
The two gaskets are not interchangeable.
Any unit with a side ported end cap and built prior to A-92-19-xxxxx must use the 8100212 gasket. Any
unit with a serial number of A-92-19-xxxxx and beyond must use the 8100565 gasket.
The end cap assembly and its appropriate gasket is interchangeable. However, piece parts are not
interchangeable.
G078
G508 G508
G068 G548 G308
G088 G908
G528
G508 G508
Old Design Twin Port New Design Twin Port

End Cap End Cap
Models affected
All 75cc variable pumps
Serial numbers
This change became effective at serial number A-96-05-xxxxx

Parts Manual
Service bulletin
Description Item 92-19 to 96-04 96-05 and beyond

End cap assembly G048 8100471 8100566
Logic block G068 364281 -
Logic block gasket G088 689117 -
Logic block screw G078 9007314-0608 -
Screw G908 - 9007314-0810
Screw G958 9007314-0804 9007314-0810
Plug G508 9005100-5600 9005110-5600
Plug G528 - 9005110-5600
Plug G548 - 9005110-5600
Parts disposition
Non-interchangeable except where noted

Parts Manual
Service bulletin
SB-1995-025
Products affected
Series 90 55, 75, and 100 cc variable pumps
Subject
Side cover design change
Description
As a product improvement, Danfoss is changing the side cover and swashplate leveler (“T-bar”) guide
post design.
The new design side cover will have two hardened inserts in the machined slot, which serves as a guide
for the swashplate leveler, and modified guide posts. The swashplate leveler does not change.
Old guide posts will remain available for service requirements of pumps with the old design side cover.
The old style side cover will be obsoleted and no longer available as a service part. A service kit has been
created for replacing the old design side cover. The kit includes the new side cover, guide posts, and
inserts.
Piece parts are not interchangeable.
Guide Post
Guide Post
Swashplate Leveler
Inserts
Side Cover
Models affected
All 55,75, & 100 cc variable pumps
Serial numbers
This change became effective at serial number A-95-50-xxxxx.

Parts Manual
Service bulletin
Description Old part numbers New part numbers

Guide post Side cover Insert assy. Guide post Side cover kit
55 cc 8100353 8000157 8000406 8000379 8510097
75 cc 8100353 8100226 8100562 8000379 8510098
100 cc 8100353 746560 8200321 8000379 8510099*
Parts disposition
Interchangeable as a kit. Piece parts are not interchangeable.

Parts Manual
Service bulletin
SB-1996-009
Products affected
Series 90 55, 75, and 100 cc variable pumps
Subject
Change swashplate feedback link
Description
As a product improvement, Danfoss is changing the design of the swashplate feedback link used on the
55, 75, and 100 cc variable pumps.
The new swashplate link has a counter bore that allows for clearance between the feedback link and the
servo arm screw. The counter bore side of the link must be installed such that the counter.
Counter bore
Models affected
All 942xxx, 952xxxx, and 962xxx variable pumps
Serial numbers
For 55and 75 cc pumps, the change became effective at serial number A-96-22-xxxxx. For 100 cc pumps,
the change became effective at serial number A-96-12-xxxxx.
Frame size Old part number New part number

55cc 8000096 8000481
75cc 8000096 8000481
100cc 8200106 8200344
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1998-066
Products affected
Series 90, 55, 75, and 100cc variable pumps
Subject
Charge pump shaft part number change
Description
As a product improvement, Danfoss has modified the design of the charge pump shaft used in series 90
55, 75 and 100 cc pumps. This change affects all charge pump sizes (11, 14, 17, 20, 26, and 31 cc) available
in the series 90 displacement range.
The series 90 55 cc variable displacement pump uses the same charge pump shaft, regardless of charge
pump size (11, 14, or 17 cc). The series 90 75 and 100 cc variable displacement pumps, utilize a common
charge pump shaft for the standard size charge pumps (75 cc standard equals 14, 17, and 20 cc and 100
cc standard equals 17, 20, and 26 cc).
A unique charge pump shaft is utilized by series 90 75 cc variable displacement pumps equipped with
the 26 cc size charge pump., while the same unique shaft is used by series 90 100 cc variable
displacement pumps equipped with 31 cc size charge pumps.
The design modification includes a surface finish change to the charge pump shaft which improves the
wear characteristics between the charge pump shaft and the journal bearings in the charge pump cover
and end cap.
To assist in identifying this change, Danfoss has released new charge pump shaft part numbers. The new
shafts are completely interchangeable with the previous shafts. The new shaft has replaced the previous
shaft in new pump assemblies and charge pump service kits. The previous shafts have been obsoleted
and are no longer available as a service part. The chart on the next page will assist you in determining the
part number changes.
Charge Pump Shaft
Models affected
94-2xxx, 942xxxx, 95-2xxx, 952xxxx, 96-2xxx, and 962xxxx variable pumps

Parts Manual
Service bulletin
Pump models 9621723 and 9622117 were released with a special charge pump option (code W-26 cc
charge pump with special shaft). With this product modification, the charge pump option code for these
two models has been changed from W to the standard option (code F-26 cc charge pump). The special
shaft part number 8801176 has been obsoleted and replaced with shaft part number 8801178.
Serial numbers
Danfoss Ames production - effective at serial number A-99-40-xxxxx
Danfoss Neumunster production - effective at serial number N-99-39-xxxxx
Series 90 Size Charge pump Previous shaft New shaft Charge kit
No aux. pad LH w/aux. RH w/aux.
55 11 8000267 8801177 8510028 8510029 8510030
55 14 8000267 8801177 8510031 8510032 8510033
55 17 8000267 8801177 8510034 8510035 8510036
75 14 8100476 8801178 8510037 8510038 8510039
75 17 8100476 8801178 8510040 8510041 8510042
75 20 8100476 8801178 8510043 8510044 8510045
75 26* 8100478 8801179 N/A N/A N/A
100 17 8100476 8801178 8510046 8510047 8510048
100 20 8100476 8801178 8510049 8510050 8510051
100 26 8100476 8801178 8510052 8510053 8510054
100 31* 8100478 8801179 N/A N/A N/A
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1998-041
Products affected
Series 90 55, 75, and 100 cc variable pumps, Series 90 55 and 75 cc variable motors
Subject
Piston hold down mechanism design change
Description
Danfoss has initiated a change to the piston hold down mechanism used on series 90 55, 75, and 100 cc
variable displacement pump and the series 90 55 and 75 cc variable displacement motors.
Previously, the hold down assembly consisted of a spacer, slipper guide bearing, washer, and screw. The
spacer provides a fixed amount of operational clearance for the slipper and slipper retainer. The guide
bearing provides a wear surface for the slipper retainer, while the hold down screws and washers retain
the assembly.
The change involved with the current design update is the removal of the washer from the assembly. This
design was initially introduced on the series 90 42 and 130 cc pumps in 1994, and with this change a
uniform product family is achieved.
With the removal of the washer, the required length of the assembly screw is reduced. The change in the
assembly screw also affects the dimensions of the spacer. Therefore, with this change, the part numbers
associated with the assembly screw and spacer have been changed. Some of the assembly screws are
parts already maintained in the parts system.
Although the new spacer and assembly screw are directly interchangeable with the previous swashplate
assembly components, we recommend that the components be serviced in combination. Since the new
spacer may be serviced as a stand alone item, the previous spacer has been obsoleted and will no longer
be available as a service part.
Spacer
Guide bearing Spacer
Washer Guide bearing
Screw Screw
Previous hold down design New hold down design
Models affected
94-2xxx,942xxxx, 95-2xxx, 952xxxx, 96-2xxx, and 962xxxx variable pumps
94-2xxx,942xxxx, 95-2xxx, and 952xxxx variable motors
Serial numbers
Danfoss Ames production - effective at serial number A-98-48-xxxxx

Parts Manual
Service bulletin
Component Displacement Prior to 98-48 Current

Hold down screw 55 cc 314419 (9007276-0114) 648477
Spacer 55 cc 8000266 8000619
Washer - pumps 55 cc 9009625-0159 N/A
Washer - motors 55 cc 9009625-0129 N/A
Hold down screw 75 cc 9007276-0099 9007276-0114
Spacer 75 cc 8100450 8100777
Washer - motors 75 cc 9009625-0129 N/A
Hold down screw 100 cc 9007276-0099 9007276-0114
Spacer 100 cc 8200216 8200422
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1998-073
Products affected
Subject
Large end cap screw change
Description
Danfoss has introduced a design modification to the Series 90 75cc Variable Displacement pump
assembly. The (4) large cap screws which fasten the end cap to the main pump housing on the Series 90
75cc and 100cc pumps have a common screw thread designation (M16x1.75). Until recently however, the
screws had a different overall length, with the screw used in 75cc pumps being 10 mm (0.394 in) shorter
than the screw used with the 100cc pumps.
Danfoss has now modified the design of the Series 90 75cc pump housing by increasing the drilled and
tapped depth of the end cap mounting screw bore. This change now makes it possible for Series 90 75cc
and 100cc pumps to use a common end cap screw. With this change, a common large screw is now used
in the assembly of 75cc and 100cc pumps which are not equipped with an auxiliary drive flange, and a
second, common large screw, is used for pumps equipped with an auxiliary drive flange. The
improvement in hardware commonality also assists in preventing insufficient gasket clamp load due to
assembly with the incorrect length screw.
It is important to note that pumps assembled prior to the change incorporation, must continue to be
serviced with the original, shorter, assembly screw. Auxiliary drive flange service kits have been updated
to include both 146mm (5.74 in.) and 156mm (6.14 in.) length screws, so that you may properly service
pumps of either vintage. The shorter screw may be used to service pumps built after the change
incorporation, if required.
To assist in identifying this change, Danfoss has released a new pump housing part number. The previous
pump housing has been obsoleted and is no longer available as a service part. The end cap screws will
continue to remain available as service items.
Models affected
95-2xxx and 962xxxx variable displacement pumps
Serial numbers
Danfoss Ames production: A-98-44-xxxxx
Danfoss Neumunster production: N-00-05-xxxxx

Parts Manual
Service bulletin
Component Prior to 98-44 Current

Pump housing 8100551 8100761
Screw- no auxiliary drive 9007210-1620 9007210-1621
Screw- with auxiliary drive 9007314-1622 9007314-1623
Auxiliary drive kits include both screws: 8102J00A-A, 8102J00B-A, 8102J00T-A and 8102J00V-A.

Parts Manual
Service bulletin
SB-1999-009
Products affected
Series 90 75cc pumps
Subject
Eliminate potential interference between speed ring and spring seats and springs
Description
Danfoss has modified the design of the swashplate leveler and spring seat assembly used on Series 90
75cc pumps. The design and serviceability of the pump has been improved by integrating the spring
seats directly into the swashplate leveler.
This new design eliminates the potential for the spring seats to separate from the leveler during assembly
and servicing.
The old spring seats part number 358523 will be available as a service part and will only be used with the
old style leveler part number 8100682.
If the need to replace the leveler part number 8100682 arises it must be replace it with the new leveler
with integrated spring seats, part number 8100698. The old swashplate leveler will be obsolete and no
longer available as a service part.
At the same time, Danfoss has changed the leveler guide post to help eliminate the possibility of
interference between the leveler and the speed ring. The new guide post allows less movement of the
leveler. The old and new guide posts are not interchangeable. The old hex head guide post, part number
8000510, must be used with the old leveler, part number 8100682. The new oval guide post, part number
8000575, must be used with the new leveler, part number 8100698.
93-2xxx, 94-2xxxx, 95-2xxx, 96-2xxxx, 97-2xxx, 98-2xxx, and 99-2xxx
Guide post Guide post
Leveler Integrated
Spring seats leveler
New design
Previous design
Models affected
All series 90 75cc variable displacement pumps
Serial numbers
Description Prior to 99-27 99-27 or later

Spring seat 358523 N/A
Leveler 8100682 8100698
Guide post 800510 8000575
Parts disposition
Interchangeable only when the new guide posts and leveler are used

Parts Manual
Service bulletin

Parts Manual
Service bulletin
SB-1999-019
Products affected
Series90 55, 75, and 100 cc variable pumps
Subject
Feedback link change
Description
As a product improvement, Danfoss is changing the design of the swashplate feedback link used on the
55, 75, and 100 cc variable pumps.
In 1996, a counter bore was added to the design of our swashplate link to allow for a higher clamping
load when assembled to the servo arm. This change was described in SB-1996-009. The counter bore is
no longer required on most units due to a design change to the servo arm. Danfoss recommends the old
feedback link be used when servicing pumps with dates codes prior to 96-40-xxxxx. The old feedback link
will remain available as a service part.
Counter bore
Models affected
All series 90 55, 75, and 100cc variable pumps
Serial numbers
Size Old part number New part number

100 cc 8200344 8200413
55 & 75 cc 8000481 11070305
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-1999-041
Products affected
Series 90 variable pumps
Subject
Change to side cover insert material
Description
As a continuous product improvement, Danfoss has changed the side cover insert material to improve
wear characteristics. The new material is more wear resistant than the previous material.
In order to track this change, new part numbers have been created and the old part numbers will be
obsolete.
Side Cover Insert Kit
Side Cover
Models affected
93-2xxx, 94-2xxxx, 95-2xxx, 96-2xxxx, 97-2xxx, 98-2xxx, and 99-2xxx
Serial numbers
Frame size NMS effective date Ames effective date

42 cc N-99-36-xxxxx N/A
55 cc N-00-18-xxxxx A-00-18-xxxxx

42 cc 506916 513885
55 cc 8000406 513886
75 cc 8000562 513888
100 cc 8200321 513889
130 cc 8300004 513890
180 cc 506914 513891
250 cc 506914 513891

Parts Manual
Service bulletin
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-1999-065
Products affected
Series 90 75, 100, 130, 180, and 250cc variable displacement pumps
Subject
Hydraulic displacement control gasket and swashplate bearing locator pin retention
Description
The Series 90 75cc, 100cc, 130cc, 180cc, and 250cc variable displacement pumps utilize a common gasket
to seal the joint between the displacement control housing and main pump housing.
In November 1998, Danfoss introduced a new gasket design for Hydraulic Displacement Controls (HDC -
all options), version 2 Electrical Displacement Controls (EDC2- options EE and EN), and two amp current
control (options PA and PB) equipped pumps (see SB-1998-038). The purpose of this gasket is primarily to
seal the joint and aid in the retention of the bearing cage locator pin in the main pump housing. Danfoss
has identified that the new gasket may not adequately aid in the retention of this pin in 75cc pump sizes
due to casting and machining tolerances. Installations which are particularly sensitive to pin retention
include those oriented with the control on the side or on the bottom when the pump is installed. In these
types of installations, it is possible for the pin to come out of its position in the pump housing. This will
result in a loss of alignment between the swashplate and swashplate bearing assembly and the potential
for erratic pump control and/or system performance.
To address this situation, Danfoss has introduced a design modification to the control gasket. The
modification will insure that the cage locator pin is retained in 75cc pumps in all circumstances, while still
maintaining the desired gasket clamp load to avoid leaks.
The new gasket is completely interchangeable with the previous gasket. Danfoss recommends that the
previous control gasket be replaced immediately on 75cc pump assemblies, with controls noted above,
in which the control is on the side or on the bottom of the pump. The pump serial numbers involved are
A-98-41-xxxxx through A-99-49-xxxxx.It is not required to replace the gasket in pumps with the control in
the up position, until the initial servicing of the pump assembly.
The 100cc, 130cc, 180cc, and 250cc pumps are not dependent upon the gasket to maintain retention of
the bearing cage locator pin and are not affected by the information above.
The new gasket has replaced the previous gasket in all new pump assemblies with Hydraulic
Displacement Control (HDC), version 2 Electrical Displacement Control (EDC2-EE and EN), and two amp
current (PA and PB) controls. The new gasket has also been placed in all appropriate control kits and
overhaul seal kits. Page 3 of this bulletin will assist you in identifying the new gasket from the previous
gasket.
Models affected
95-2xxx,952xxxx, 96-2xxx, 962xxxx, 97-2xxx, 972xxxx, 98-2xxx, 982xxxx, 99-2xxx, and 992xxxx variable
displacement pumps equipped with hydraulic displacement controls and specific option electronic
displacement control. (EE, EN, PA, PB)
Serial numbers
Danfoss Ames 75cc pump production:A-99-50-xxxxx.
Danfoss Ames 100cc pump production: A-00-25-xxxxx.
Danfoss Neumunster production: N-00-01-xxxxx.

Parts Manual
Service bulletin
Previous gasket New gasket

511608 8801241
Parts disposition
Interchangeable
Control Gasket
Cage locator pin
Retains Cage Locator Pin
New Gasket:
Previous Gasket:

Parts Manual
Service bulletin
SB-2000-022
Products affected
Series 90 75, 100, and 130 cc variable displacement pumps
Subject
Displacement limiter screw and servo piston change
Description
Danfoss has identified a product issue affecting a limited number of Series 90 100cc variable
displacement pumps built at the Ames, Iowa, USA facility in the time frame of June 2000 through August
2000 (serial date range A-00-23-xxxxx up to and including A-00-34- xxxxx). This same issue also affects a
limited number of Series 90 75cc, 100cc, and 130cc variable displacement pumps built at the
Neumunster, Germany facility in the time frame of June 2000 through September 2000 (serial date range
N-00-23-xxxxx up to and including A-00-39-xxxxx).
These pumps, equipped with displacement limiters, may have a servo piston with large center drills.
These large center drills may allow the displacement limiter screw to thread into the servo piston while
turning the screw in against the servo piston while adjusting the pump’s displacement. If this occurs, the
pump will be mechanically held in stroke by the displacement limiter screw. This situation can only
happen during adjustment; it will not occur during normal operation.
Danfoss has introduced a change to the servo piston and the displacement limiter screw to prevent the
recurrence of this issue. We have made a change to the servo piston to limit the size of the center drill. We
have also changed the design of the service displacement limiter screw from a “flat” point to a “dog nose”
point. When servicing a pump that meets the above criteria, you must verify that the displacement limiter
screw of the new “dog nose” version. If it is not, you must replace the displacement limiter screw with the
new version. If the pump is not inside the date code ranges and displacements mentioned, you do not
need to verify the version of the displacement limiter screws.
To assist in tracking this change, we have issued new part numbers for the servo pistons and
displacement limiter screws. Even though this issue did not affect the 42cc or 55cc pumps, the service
displacement limiter screw part number will change also to keep one common service part. We do this as
the same displacement limiter screw is used on 42cc, 55cc, 75cc, and 100cc pumps.
Old New
“flat point” “dog nose”
displacement limiter screw displacement limiter screw
Models affected
All 95-2xxx, 952xxxx, 96-2xxx, 962xxxx, 97-2xxx, and 972xxxx variable displacement pumps with 1, 2, 4, or
P displacement limitation option.
Serial numbers
Danfoss Ames 100cc production with serial number A-00-23-xxxxx up to and including A-00-34-xxxxx.
Danfoss Neumunster, Germany production with serial number N-00-23-xxxxx up to and including
A-00-39-xxxxx.

Parts Manual
Service bulletin
Frame size Old servo piston New servo piston Old screw New screw
42 & 55cc N/A N/A 9007712-0814 516677
75 cc 509282 516683 9007712-0814 516677
100 cc 509284 516684 9007712-0814 516677
130 cc 510496 516685 572180 516678
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-2000-041
Products affected
Series 90 55, 75, 1nd 100 cc variable displacement pumps
Subject
Common leveler spring shim
Description
The date code for the series 90 55cc should have been for a date code of A-92-06-xxxxx not A-02-06-
xxxxx.
Danfoss has standardized the leveler spring shim used on all 55, 75, and 100 cc variable displacement
pumps. Two different shims were used in the past. One size was for 55 and 75 cc pumps, and the other for
the 100 cc pumps. The new shim can be used in all three frame sizes.
Danfoss has issued a new part number for the new shim. The new shim is interchangeable for 55 cc
pumps built after A-92-06-xxxxx, 75 cc pumps built after A-96- 19-xxxxx,and 100 cc pumps. For pumps
manufactured prior to these dates, you will need to reuse the old shims, as the new shim outer diameter
is larger, and this will cause the new shim to not seat correctly in the bottom of the pocket in the end cap.
The old shim part numbers are obsolete.
Models affected
All 94-2xxx, 942xxxx, 95-2xxx, 952xxxx, 96-2xxx, and 962xxxx variable pumps.
Serial numbers
Danfoss Ames, Iowa production change was effective at serial number A-00-40-xxxxx
Danfoss Neumunster, Germany production change was effective at serial number N-01-27-xxxxx

55 cc 359042 8801225*
75 cc 359042 8801225**
100 cc 359059 8801225
* can only be used in pumps manufactured after A-92-06-xxxxx
** can only be used in pumps manufactured after A-96-19-xxxxx
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-2002-050
Products affected
Series 90 55, 75, and 100 cc pumps
Subject
Auxiliary mounting pad
Description
As a product improvement, Danfoss has changed the design of the SAE C auxiliary mounting pad to
increase strength and reduce corrosion. The old auxiliary mounting pad and new auxiliary mounting pad
are interchangeable. The new auxiliary mounting pads are frame size dependent, because they do not
have slotted mounting holes. The auxiliary mounting pad screws remain the same, but they do not
require washers.
The old auxiliary mounting pad is obsolete and no longer available as a service part. The washers will
remain available.
Old design New design
Models affected
Series 90 55, 75, and 100 cc pumps with SAE C auxiliary mounting.

The new auxiliary mounting pads are frame size dependent and do not use washers.
Frame size Old aux-pad part number New aux-pad part Old washer part number
number
55cc 723205 8000643 5000602
75cc 723205 8100848 9009625-0132
100cc 723205 8200469 9009625-0132
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-2004-012
Products affected
Series 90 55cc and 75cc pumps
Subject
Cage locator pin
Description
As a product improvement, Danfoss is standardizing the cage locator pin for all series 90 55, 75, and 100
cc pumps. All 55 and 75 cc pumps will now use the same locator pin used in 100 cc pumps. The new
locator pin extends 2 mm further into the housing than the old pin. The housings have been machined to
accept the longer pin.
The old cage locator pin must be used in pumps that have not had the housings modified. The old pin
can be used in any vintage pump and will remain available as a service part.
Cage locator pin
Models affected
Series 90 55cc and 75cc pumps
Serial numbers and part numbers affected
Frame size Old number New number Housing modification

date*
A-04-43-xxxxx
55cc 8801135 8801235 N-04-43-xxxxx
S- not determined
A-01-26-xxxxx
75cc 723205 8100848 N-00-01-xxxxx
S- not determined
100cc 8801235 8801235 No change
* A = Ames, Iowa; N = Neumunster, Germany; S = Shanghai, China
Parts disposition
Non-interchangeable

Parts Manual
Service bulletin
SB-2005-007
Products affected
Series 90 75cc pumps
Subject
Pump redesign
Description
As a global improvement, the series 90 75cc displacement pump has redesigned components as a
product improvement program. The following components are being redesigned: servo arm, swashplate
guide, pump housing, shaft seal, and cradle bearing.
All parts are non-interchangeable with the exception of the shaft seal. Model numbers and order codes
will not be changed.
Servo arm: A “one piece” servo arm is introduced. The pin that engages the servo piston is now machined
as part of the servo arm instead of pressed in. The old servo arm will remain available as a service part for
a period of time.
Swashplate Guide: The swashplate position is now guided by the fit between the servo arm and the
pump housing . A “shelf” on the servo arm fits under a boss in the housing to provide a fixed clearance
swashplate hold-down. The swashplate was previously held down with a spring and bracket, which was
riveted to the servo arm. The servo arm to housing clearance now limits lateral movement of the
swashplate. The separate swashplate guide that was bolted to the bottom of the swashplate has been
removed. The separate swashplate guide will remain available as a service part for a period of time.
Housing: The housing is modified internally to provide the servo arm pivot. Also, the cradle and side
cover radii are reduced. The housing casting is common globally. Some customers may notice cosmetic
external changes. The old housing will be obsoleted and no longer available as a service part.
Shaft seal: The new shaft seal is interchangeable with the old version. The shaft seal will be sourced from
one global supplier. The old shaft seal will be obsoleted and no longer available as a service part.
Cradle bearing: The new design is a single piece cold formed with the positioning pin now integral with
the bearing. The old cradle bearing will remain available as a service part for a period of time.
Side cover: The side cover will have a 138.58 mm pilot as the old side cover had a 140.589 mm pilot.
The current version of the housing will not be available globally long term. Current bearings will be
available under the 8700048 part number. Swashplate 8100367 will be maintained for service parts. It is
interchangeable for the 516201 swashplate in current housings. Fastener 660032 (90007276-0107),
swashplate guide 8800669, and spring 8100035 are used in other series 90 frame sizes and will remain
active. The side cover will be kept for service parts replacement.
Models affected
All 952xxxx pumps.
Serial numbers affected

This change was effective at serial number: A-05-49-xxxxx, N-05-40-xxxxx and S-05-47-xxxxx.
Description Old part number New part number

Housing 500170 (N), 724674 ( N), 8100761 (A) 11001300
Cradle bearing 676841/P (N), 8700048 (A) 518671
Servo arm 518323 (N), 8100499 (A) 519046

Parts Manual
Service bulletin

Swashplate 516201 (N), 8100367 (A) 521366 (N), 11000688 (A)
Screw 666032 (N), 9007276-0107 (A) 519150
Swashplate guide 8800669 No longer used
Spring 664367 (N), 8100035 (A) No longer used
Side cover 501572 11001286
Shaft seal assembly 510015 (N), 8100553 (A) 519671
Lip seal 664508 (N), 9008000-0115 (A) 519666
Side cover kit 8510098 8510392
Swashplate assembly 8100376 8100984
Servo/swashplate kit 8100377 8510391
Parts disposition
Non-interchangeable; interchangeable.
See Description for details.

Parts Manual
Service bulletin
SB-2005-011
Products affected
Series 90 42 through 100 cc pumps
Subject
Auxiliary flange charge pump cover
Description
Danfoss will no longer mark auxiliary flange charge pump cover with an “R” for right hand rotation or an
“L” for left hand rotation.
The pilot surface has changed on the covers. The right hand rotation charge pump cover will have 1 step
and the left hand rotation charge pump cover will have 2 steps. Refer to the drawings below for example.
The part numbers of the charge pump covers will not change.
Right hand Left hand

rotation rotation
Models affected
Series 90 42 thru 100 cc pumps with auxiliary pad options.
Serial numbers

None
Parts disposition
Interchangeable

Parts Manual
Service bulletin
SB-2007-027
Products affected
Series 90; 55, 75 , and 100 cc pumps
Subject
SAE A auxiliary mounting flange
Description
Danfoss is pleased to announce a design improvement on the SAE A auxiliary mounting flange adapter
on all its series 90 pumps. All manufacturing locations producing these pumps will be changed to this
configuration.
The improvement comes in the form of a more robust sealing geometry with a larger cross- section O-
ring. The O-ring groove in the flange will now be sized to mate with a 2.62mm [0.103] cross section O-ring
rather than the old 1.78mm [0.070] cross-section O-ring.
The Danfoss part number for the new O-ring is 9004104-1520 (2.62mm [0.103]. x 82.22mm [3.237]). The
larger cross-section sealing geometry allows for the use of a donut style A pad seal and a new flat cover
for improved assembly. This new configuration is qualified as a running cover. When installing an
auxiliary pump, the donut style A pad seal must be discarded and the part number 9004104-1520 O-ring
used.
Also, the flanges will no longer have a slotted interface with a washer for the end cap screws. The flanges
will now have round through holes for the end cap screws and will use no washers. The end cap screws
do not change. This eliminates the area where water or high pressure wash chemicals can be trapped
around the end cap screws. There now are specific part numbers for the flanges used on each of the three
displacement size pumps; 55, 75 and 100 cc.
The pumps will now be supplied with the donut style A pad seal and new flat cover, instead of the small
O-ring and cover plate (shown in the drawing below).
The overhaul seal kit will include the old O-ring, the new O-ring and the A pad seal.
Old Design New Design
Flange adapter Flange adapter

Washer
O-ring A pad seal
Cover plate Cover plate
Models affected
All series 90; 55, 75, and 100 cc pumps with SAE“A” auxiliary mounting flanges.
Serial numbers

Parts Manual
Service bulletin
Description Old p/n Used on New p/n Used on

Flange adapter 8000262 55 cc 8000641 55 cc
Flange adapter 8800172 55, 75 & 100 cc 8000641 55 cc
Washer 9009625-0132 55, 75 & 100 cc NA NA
O-ring 9004104-0420 All sizes 9004104-1520 All sizes
A Pad seal NA All sizes 4800482 All sizes
Flange cover 9802336 All sizes 4460586 All sizes
If the new auxiliary flange adapter is used, the new o-ring or A-pad seal and cover must also be used.
Parts disposition
• Interchangeable- if new o-ring or A-pad seal and cover are replaced
• Use parts in stock
• Order replacement parts
• Revise existing part orders

Parts Manual
Service bulletin
SB-2007-051
Products affected
Subject
SAE C auxiliary mounting flange
Description
Danfoss is pleased to announce a design improvement on the SAE C auxiliary mounting flange adapter
on its series 90 pumps. The frame sizes affected by this change are 55, 75, and 100cc. All manufacturing
locations producing these pumps will be changed to this configuration.
The improvement comes in the form of a more robust sealing geometry with a larger cross-section O-
rather than the old 1.78mm [0.070] cross-section O-ring. The Danfoss part number for the new O-ring is
9004104-1580 (2.62mm [0.103] x 120.32mm [4.737]). The larger cross-section sealing geometry allows for
the use of a donut style C pad seal and a new flat cover for improved assembly. This new configuration is
qualified as a running cover. When installing an auxiliary pump, the donut style C pad seal must be
discarded and part number 9004104-1580 O-ring used.
The pumps will now be supplied with the donut style seal and new flat cover, instead of the small O-ring
and cover plate (shown in the drawing below).
The overhaul seal kit will include the old O-ring, the new O-ring and the new C pad seal.
1.30 mm 1.96 mm
[0.05] [0.08]
Adapter flange
Adapter flange
C pad seal
O-ring
Flat flange cover

Piloted flange cover
Models affected
All series 90; 55, 75, and 100 cc pumps with SAE“C” auxiliary mounting flanges.
Serial numbers
This change became effective at serial number A-08-19-xxxxx and N-09-30-xxxxx

Parts Manual
Service bulletin
Description Old part number Used on New part number

SAE C flange 8200469 100cc 8200515
SAE C flange 8100848 75cc 8100897
SAE C flange 8000643 55cc 8000740
O-ring 9004100-0480 55, 75, 100cc 9004104-1580
C pad seal N/A 55, 75, 100cc 8801062
Flange cover 8800406 55, 75, 100cc 8801060
If the auxiliary flange adapter is used, the new o-ring or C pad seal and cover must also be used.
Parts disposition
• Interchangeable- if new o-ring or C pad seal and cover are replaced

Parts Manual
Service bulletin
SB-2007-055
Products affected
Subject
SAE B auxiliary mounting flange
Description
Danfoss is pleased to announce a design improvement on the SAE B auxiliary mounting flange adapter
on its series 90 pumps. The frame sizes affected by this change are 55, 75, and 100cc. All manufacturing
locations producing these pumps will be changed to this configuration.
The improvement comes in the form of a more robust sealing geometry with a larger cross-section O-
rather than the old 1.78mm [0.070] cross-section O-ring. The Danfoss part number for the new O-ring is
9004104-1540 (2.62mm [0.103] x 94.92mm [3.737]). The larger cross-section sealing geometry allows for
the use of a donut style B pad seal and a new flat cover for improved assembly. This new configuration is
qualified as a running cover. When installing an auxiliary pump, the donut style B pad seal must be
discarded and part number 9004104-1540 O-ring used.
Also, the flanges will no longer have a slotted interface with a washer for the end cap screws. The flanges
will now have round through holes for the end cap screws and will use no washers. The end cap screws
do not change. This eliminates the area where water or high pressure wash chemicals can be trapped
around the end cap screws. There now are specific part numbers for the flanges used on each of the three
displacement size pumps; 55, 75 and 100 cc.
The pumps will now be supplied with the donut style seal and new flat cover, instead of the small O-ring
and cover plate (shown in the drawing below).
The overhaul seal kit will include the old O-ring, the new O-ring and the new B pad seal.
1.30 mm 1.96 mm
[0.05] [0.08]
Adapter flange Adapter flange
Washer
O-ring
- B pad seal
Flat flange cover

Piloted flange cover
Models affected
All series 90; 55, 75, and 100 cc pumps with SAE“B” auxiliary mounting flanges.

Parts Manual
Service bulletin
Serial numbers
Description Old part number Used on New part number Used on

Metric B flange 8800983 55, 75 & 100 cc 8200540 100 cc
SAE B flange 8800173 55, 75 & 100 cc 8200468 100 cc
SAE B flange 8800173 55, 75 & 100 cc 8100847 75 cc
Metric B flange 8800983 55, 75 & 100 cc 8100938 75 cc
SAE B flange 8800173 55, 75 & 100 cc 8000642 55 cc
SAE B flange 8000263 55, 75 & 100 cc 8000642 55 cc
Washer 9009625-0132 55, 75 & 100 cc N/A N/A
O-ring 9004104-0450 55, 75 & 100 cc 9004104-1540 55, 75 & 100 cc
B Pad seal N/A 55, 75 & 100 cc 8801061 55, 75 & 100 cc
Flange cover 4460370 55, 75 & 100 cc 8801059 55, 75 & 100 cc
If the new auxiliary flange adapter is used, the new o-ring or B pad seal and cover must also be used.
Parts disposition
• Interchangeable- if new o-ring or C pad seal and cover are replaced

Parts Manual
Service bulletin
SB-2009-073
Products affected
Series 90: 75 and 100 cc pumps
Subject
Supplier change for guide posts
Description
The supplier has changed, for the guide posts used in series 90: 75 and 100 cc pumps. The new guide
posts are interchangeable with the old guide posts. A new part number has been assigned to the new
guide post to better track this change. The old part number has become obsolete and not available for
service.
Guide post
Models affected
Series 90: 75 and 100cc pumps
Serial numbers
This change became effective at serial number A-09-50-xxxxx (21 December 2009)

Guide post 8000575 11056531

Parts Manual
Service bulletin

Interchangeable

Parts Manual
Service bulletin
SB-2013-011
Products affected
Series 90: 42-250cc pumps
Subject
Feedback link - control
Description
Danfoss has changed to a global supplier for the control feedback links used in Series 90 42-250cc
pumps.
Old parts and new parts are completely interchangeable. Part numbers will be changing for tracking
purposes. Old parts will become obsolete and no longer available as a service part.
Control feedback link
Models affected
Control feedback link Old part number New part number

42cc pumps 648600 11070304
55 & 75cc pumps 8000602 11070305
100cc pumps 8200413 11070306
130cc pumps 340091 11070307
180 & 250cc pumps 747451 11070308
Parts disposition
• Interchangeable

Parts Manual
Service bulletin
SB-2015-005
Products affected
Subject
Slider block supplier change
Description
The supplier has changed for Series 90 pump slider blocks. Parts are completely interchangeable.
Part numbers have been changed for tracking purposes. As a result old part numbers will become
obsolete and no longer available as service parts.
Slider block
Models affected
Series 90 42-250cc pumps
Description Old Part Number New Part Number Effective Date

Slider block 42 NMS 648303 11116314 N/A
Slider block 55-75 NMS 8800750 11116313 6-Aug-2014
Slider block 55-75 AMS 11061964 11116313 6-Sept-2014
Slider block100 AMS 11061908 11116312 10-Mar-2014
Slider block 100 NMS 756197 11116312 20-Feb-2015
Slider block 130 NMS 11000317 11116309 9-Dec-2014
Slider block 180-250 NMS 746479 11116308 24-Oct-2014
Parts disposition
• Interchangeable

Parts Manual
Service bulletin
SB-2017-033
Products affected
Series 90 pumps
Subject
Swashplate service kit revision
Description
The swashplate service kit for Series 90 75cc NFPE pumps has been revised following a design change to
the pump housing on those units. The housing change required a change to the location of the cradle
bearing cage locator link on the swashplate. The link is now located under the side cover.
Parts are not interchangeable.
Models affected
Series 90 75cc NFPE pumps
Serial numbers affected

This change became effective at serial number N1732xxxxx (August 11, 2017)
Description Old part number Description New part number

Swashplate SVC kit 11103350 Swashplate SVC kit 11192313
90PV075 w/o D65, M14 - 90P075 NFPE assembly -
Parts disposition
Non-interchangeable; use parts in stock with old style pump housings

Products we offer: Danfoss Power Solutions is a global manufacturer and supplier of high-quality hydraulic and
electric components. We specialize in providing state-of-the-art technology and solutions
• DCV directional control
that excel in the harsh operating conditions of the mobile off-highway market as well as the
valves
marine sector. Building on our extensive applications expertise, we work closely with you to
• Electric converters
ensure exceptional performance for a broad range of applications. We help you and other
• Electric machines customers around the world speed up system development, reduce costs and bring vehicles
• Electric motors and vessels to market faster.
• Gear motors Danfoss Power Solutions – your strongest partner in mobile hydraulics and mobile
• Gear pumps electrification.
• Hydrostatic motors Go to www.danfoss.com for further product information.

• Hydrostatic pumps We offer you expert worldwide support for ensuring the best possible solutions for
outstanding performance. And with an extensive network of Global Service Partners, we also
• Orbital motors
provide you with comprehensive global service for all of our components.
• PLUS+1® controllers
• PLUS+1® displays
• PLUS+1® joysticks and
pedals
• PLUS+1® operator
interfaces
• PLUS+1® sensors
• PLUS+1® software
• PLUS+1® software services,
support and training
• Position controls and
sensors
• PVG proportional valves
• Steering components and
systems
• Telematics
Hydro-Gear
www.hydro-gear.com Local address:
Daikin-Sauer-Danfoss
www.daikin-sauer-danfoss.com
Danfoss
Power Solutions Trading
Danfoss Danfoss Danfoss (Shanghai) Co., Ltd.
Power Solutions (US) Company Power Solutions GmbH & Co. OHG Power Solutions ApS Building #22, No. 1000 Jin Hai Rd
2800 East 13th Street Krokamp 35 Nordborgvej 81 Jin Qiao, Pudong New District
Ames, IA 50010, USA D-24539 Neumünster, Germany DK-6430 Nordborg, Denmark Shanghai, China 201206
Phone: +1 515 239 6000 Phone: +49 4321 871 0 Phone: +45 7488 2222 Phone: +86 21 2080 6201
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
© Danfoss | July 2020 AX152886482206en-0501

Series 90 Axial Piston Pumps: Size 75cc

Uploaded by

Copyright:

Available Formats

Series 90 Axial Piston Pumps: Size 75cc

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Series 90 Axial Piston Pumps: Size 75cc

Uploaded by

Copyright:

Available Formats

Parts Manual

Series 90 Axial Piston Pumps

Revision history Table of revisions

Date Changed Rev

2 | © Danfoss | July 2020 AX152886482206en-0501

© Danfoss | July 2020 AX152886482206en-0501 | 3

4 | © Danfoss | July 2020 AX152886482206en-0501

Control NE...................................................................................................................................................................................... 227

© Danfoss | July 2020 AX152886482206en-0501 | 5

6 | © Danfoss | July 2020 AX152886482206en-0501

Service Parts Identification

Model No./Ident No. 9521216

© Danfoss | July 2020 AX152886482206en-0501 | 7

Example: The service part desired is item G30

About service bulletins

Procedure to identify a part

Regional part numbers

Example of a part identification (S90 75cc)

8 | © Danfoss | July 2020 AX152886482206en-0501

Adobe Acrobat 2-page viewing

© Danfoss | July 2020 AX152886482206en-0501 | 9

Auxiliary mounting pad

Special hardware features

High pressure setting port A

High pressure setting port B

Charge pressure setting

10 | © Danfoss | July 2020 AX152886482206en-0501

Common parts and special hardware

S90P 75cc common parts

B80 L60 L70

Swashplate Leveler design

* Included in base pump seal kit Q210

© Danfoss | July 2020 AX152886482206en-0501 | 11

Common parts and special hardware

Part numbers continue to the next 2 pages.

12 | © Danfoss | July 2020 AX152886482206en-0501

Common parts and special hardware

B80 L60 L70

Swashplate Leveler design

* Included in base pump seal kit Q210

© Danfoss | July 2020 AX152886482206en-0501 | 13

Common parts and special hardware

14 | © Danfoss | July 2020 AX152886482206en-0501

Common parts and special hardware

S90P 75cc special hardware EAB-EBA

(EAB, EAS, EAV & EBE)

(EAC, EBA & EBC)

Generic speed sensors shown.

* Included in base pump seal kit Q210

© Danfoss | July 2020 AX152886482206en-0501 | 15

Common parts and special hardware

Order code: EAB

Order code: EAC

Order code: EAS

Order code: EAV

Order code: EBA

16 | © Danfoss | July 2020 AX152886482206en-0501

Common parts and special hardware

S90P 75cc special hardware EBC, EBE