DC SEQUENCER FOR DEDUSTING PLANTS

PLEASE READ THE WHOLE USER MANUAL CAREFULLY BEFORE INSTALLING THE EQUIPMENT

DESCRIPTION
Sequencer for dedusting plant cleaning cycle control with
digital dP control by internal transducer. Device with
microprocessor management and zero-crossing detection
for the outputs activation to give high immunity from
external interference and low field emission.
Max 3 output relays, Max 3 digital voltfree input

DOCUMENTATION INDEX

- Introduction
- Installation rules and technical features
- Enter datas in SET MODE
- RUNNING MODE and Alarms description
- Standard features details
- Option on request
- Electrical Wiring Diagram
- Board layout
- Housing and Dimension
- Problems solution
- CE certificate

STANDARD FEATURES

A1a Out Minimum and maximum dP alarms on same relay (K2)

A2a Out Relay Voltage ON (K1)
B1b Select Number of outputs
B2x Activation time from 0.05 to 5.00 sec.
B3x Interval time from 1 to 999 sec.
B3c Interval time between ev. during post-cleaning
B8b Short-circuit protection of every single output
B10 Manual activation of every single output from keyboard
C1 Digital differential pressure control (STOP at cycle end)
C4 Cleaning cycle
C8 dP zero readout regulation
C7c1 Out Minimum dP alarm. Contact open with alarm. Automatic reset.
C7d1 Out Maximum dP alarm. Contact open with alarm. Automatic reset.
C13_10 dP full range 10kPa
D1b1 Additional post-cleaning cycles from dP readout. Activation at STOP.
D5a In Consent from external compressed air pressure switch
D6a In ON/OFF cleaning cycle from external contact
D14a Operation hours-counter
DPa 6x4 RILSAN air connections
G1 Maximum load power 25W per output
HVB Input and output voltage selection
SL Multi language display

In = Input Signal. Voltfree contact

Out = Output signal. Relay Contact
Code: DC16BU7.1
S/N:
Date: 19 / 07 / 2016 Ver. 13.0
 INSTALLATION RULES

Protect the device against the direct exposure to the sun.

Avoid arranging the device in the proximity of or in direct contact with any source of heat and electromagnetic field. Connect the
device on supply lines different from those used for motor drives or other devices that may cause some noise on the net.

Fix the device on the wall at minimum 60 cm from the floor.

For all input control signals to the Timer (D1a, D5, D6,...) use anti-flame wires with a minimum section of 0.5 mm².
Before acting on the device for any operation, check for safe conditions. For electrical operations never forget to disconnect the
power supply, wait for 30 seconds for the internal capacitors discharge before opening. At the end of the operations close the
device to restore the protection degree before powering again.

For the electrical connection of the supply voltage and filter cleaning electrovalves use anti-flame wires with a minimum section
of 0.75 mm². For output relay contacts use anti-flame wires with a minimum section of 1.5 mm2.

For the output signal 4÷20 mA use anti-flame shielded wire with minimum section of 0,5 mm².

For the electrical connections use antiflame shielded cable 3 x 0,75 mm²

ATTENTION: with output voltage 230VAC use connectors with RC filter or insert it on every supply line of any ev.
If filters are not used, an operating malfunction could happen.

TECHNICAL FEATURES

Supply Voltage 24 VAC ± 10 % - 50/60 Hz

Output voltage: 24 VDC
Fuse 250 V / 2 A F (5x20)
Power requirement: 10 VA (Stand-by) - 30 VA ev. ON
Operating temperature -10 ÷ + 50 °C
No. Outputs 16
dP Control With internal trasducer
Dimensions: / Protection degree 240x185x114 mm. / IP65
Terminals 2,5 mm² 250 VAC / 12 A

A wrong supply voltage connection might cause irreparable damages to the device.

The fuse wire protect only from any short circuit and not necessarily from wrong supply voltage.

We reserve the right to make any change without notice

Pg. 2
 ENTER DATAS IN SET MODE

When supply voltage switch On the cleaning cycle starts if all the necessary conditions for running are
present.
Press key B to enter in SET MODE.
The upper line of the display shows the code and the description of the selected function and the line
below shows the referement code and the value of the fuction indicated (See table SET DATA).
Press key B to increase the number of the selected function.
Press key D to decrease the number of the selected function.
Press key A to increase the set value.
Press key C to decrease the set value.
Press key E to store the SET UP data and to enter in RUNNING MODE.
If for 5 minutes no key is pressed the device change automatically in RUN MODE.

A / C Increase - Decrease Value

E ESC / Reset
B / D Increase - Decrease Code

DISPLAY DESCRIPTION Range Rif. Default

00 LANGUAGE SEL. Display language selection SL

SL ENGLISH

01 DIGITAL INPUTS Enable / Disable digital inputs CO

C0 ACTIVATED

02 OPERATION Operation Mode selection Manul / Automatic C4a

C4a AUTOMATIC

03 PULSE TIME Activation time from 0.05 to 5.00 sec. 0.01÷5.00 B2x 1.00 sec
B3x 1 sec.

04 INTERVAL TIME Interval time between ev. from 1 to 999 sec. 001÷999 B3x 5 sec
B3x 005 sec.

05 POSTCL INT. Interval time between ev. during post-cleaning 001÷999 B3c 5 sec
B3c 005 sec.

06 POST CYCLES Additional cycles after fan stop 00÷99 D1x 5

D1x 002 cycles

07 ELECTROVAL.N. Selection Number of outputs / solenoid valves B1a

B1a 016 ev.

08 TEST EV. Manual activation of every single output from keyboard B10
B10 001 OFF

09 HOURS COUNTER Operation hour-counter 0÷65535 D14a

D14a 00000 hour

10 REG ZERO dP dP zero readout regulation C8 0.00

C8 0.00 kPa

11 FAN THRESHOLD dP threshold for cycle activation after fan stop 0.01÷0.99 D1bx 0.10
D1bx 0.10 kPa

12 MIN dP ALARM Minimum dP alarm threshold 0.01÷9.99 C7c1 OFF

C7d1 OFF kPa

13 dP STOP CYCLE 1st dP threshold, STOP washing since dP low 0.01÷9.99 C1a 1.00
C1a 1.00 kPa

14 dP START CYCLE 2nd dP threshold, START washing since dP high 0.01÷9.99 C1b 2.00
C1b 2.00 kPa

15 MAX dP ALARM Maximum dP alarm threshold. 0.01÷9.99 C7d1 3.00

C7d1 3.00 kPa

18 EV. VOLTAGE Output voltage setup for ev. (see HVB) (Necessary for right B operating of HV
HV Vout = 24 V B8b)
Pg. 3
 INFO MODE

In run mode by pressing key D the device enter in INFO MODE. In this modality is avaliable a
description of keys function in SET UP and RUN MODE.
Press key B to go on in the informations visualization.
Press key E to exit and come back to RUN MODE.
If for 5 minutes no key is pressed the device change automatically in RUN MODE.

NOTE: When the device enter in INFO MODE the cleaning cycle stops. It restart from the beginning
when the device return in RUN MODE.

B Next
E Exit

DISPLAY DESCRIPTION

INFO B = NEXT Key use in INFO mode

E = EXIT

KEY FUNCTION
IN OPERATING

A=SCROLL ALARMS Key A = Display all active alarms in sequence

B=ENTER SET UP Key B = Enter in setup mode

C = VISUAL dP/TC Key C = Change display between dP and TC readout (OPTION)

D = INFO Key D = Enter in INFO mode

E = ALARMS RESET Key E = Reset alarms

KEYS FUNCTION
IN SETUP

A/C=INC/DEC DATA Keys A / C = Modify set up datas

B/D=INC/DEC CODE Keys B / D = Increment/decrement set up function

E = SET UP EXIT Key E = Exit Setup and store data

Pg. 4
 RUNNING MODE

When supply voltage switch On the cleaning cycle starts if all the necessary conditions for running are
present.
The upper line of the display shows the differential pressure reading or TC signal reading depend on
the selection (option) and the type of operating mode (Manual / Automatic).
The line below shows a series of informations of the run status and the alarm situations active (See
table below / alarm description).
If no one key is pressed for 30 seconds the backlight brightness decrease, to ensure upper energy
safe and longer life of the display, up to a key is pressed again.

B Enter in SET UP
D Enter in INFO MODE
A Active alarm Scrolling
C Change visualization dP/TC (option)
E Alarm Reset

DISPLAY DESCRIPTION Rif.

dP = 9.99 kPa MAN Differential pressure readout C3

Manual running mode

TC = 010 mg/m³ AUTO TC Probe readout (Option on request) D11

Automatic running mode

START CONTACT Cycle stop since no remote start D6a

D6a OPEN

Cycle waiting for fan start or dP under set fan threshold D1x
VENTILATOR STOP

Activation output / solenoid valve 003

ACTIVAT. EV. 003

Waiting time before activation of the next ev.

WAITING=005 sec.

CYCLE STOP Cycle stop because differential pressure below 13 C1a

FOR dP LOW

Active cycles after fan stop D1x

POSTCLEANING ACT

Pg. 5
 ALARMS DESCRIPTION

In run mode the lower line of the display shows the active alarm situations.
By pressing key A it is possible to scroll all the active alarms.
By pressing key E it is possible to reset the alarms.
The table below shows all the possible alarm situations. Some of these are related to particular
options on request and they are not present in Standard version.
The alarm visualization got the priority on other visualization on the 2nd line of the display.

A Alarms scrolling
E Alarms Reset

DISPLAY DESCRIPTION Rif.

E1 OVERLOAD Overload alarm - Solenoid velves 03 B8b

ELECTROVALVE 003

E2 ACT. FAILED Solenoid valve not activated - Solenoid valves 03 B9x/B6x

ELECTROVALVE 003

E6 COMPR. AIR Cycle stop since no consent from compressed air pressure switch D5a
LACK D5a OPEN

E7 ALARM Maximum dP alarm active. C7d

MAXIMUM dP dP reading over SET 15

E8 ALARM Minimum dP alarm active C7c

MINIMUN dP dP reading under SET 12

Pg. 6
 STANDARD FEATURES

A1a MINIMUM AND MAXIMUM DP ALARMS ON SAME RELAY (K2)

Minimum and maximum dP alarms act on the same relay. The display will specify the type of alarm.
A2a RELAY VOLTAGE ON (K1)
If the timer is supplied, relay K1 is activated and the terminal board contact is closed. In case of power failure, this contact is open.
B1b SELECT NUMBER OF OUTPUTS
The selection of the number of outputs to be control led is connected by keyboard in SET MODE. If you set 0 or AUTO in this function the sequencer
will automatically select the connected loads by skipping the non connected ones. Minimum load 5W ÷ 12 W depending on the output voltage.If the
load is below 5 W, autoselection does not work, set the number of outputs in set up.
B2x ACTIVATION TIME FROM 0.05 TO 5.00 SEC.
B3x INTERVAL TIME FROM 1 TO 999 SEC.
If the pulse time is lower than 1 sec. it is possible to set any interval time value in the range indicated.
If the activation time is higher than 1 sec. the minimum settable interval time is:
Minumum interval time = 5 times pulse time (B2x)
B3c INTERVAL TIME BETWEEN EV. DURING POST-CLEANING
Interval time between two activations settable by keyboard when post-cleaning cycles are active and during the forced cycles of option C2x if
available.
The selection range is the same as the inteval time in standard operation mode (B3x).
B8b SHORT-CIRCUIT PROTECTION OF EVERY SINGLE OUTPUT
In case of short-circuit, the corresponding output is automatically skipped. Relay K2 will signal the alarm condition and display will show the alarm
situation code E1 (See the alarm description).
Press key E to reset the alarm.
B10 MANUAL ACTIVATION OF EVERY SINGLE OUTPUT FROM KEYBOARD
By keyboard, it is possible to activate manually and individually every single output for an operation test.
Press key C to select the desired output to be activated. Press key A to activate the output.
The output is holded active for all the time that key A is pressed. It allows to measure the output voltage by using a tester.
In case of anomalous operating, do this test with electrovalves disconnected.
C1 DIGITAL DIFFERENTIAL PRESSURE CONTROL (STOP AT CYCLE END)
In automatic running mode (C4a), the washing cycle is activated and deactivated according to the dP readout.
C1a Set the washing STOP threshold: if dP is below this threshold, the washing cycle stops and the display shows 'CYCLE STOP FOR LOW dP'
(letter 'P' for model DB). The washing cycle stops at the end of the cycle (Set 13).
C1b Set the washing START threshold: if dP is above this threshold, the washing cycle is activated (Set 14)
C4 CLEANING CYCLE
If all the requirements for the start-up of the cleaning cycle are fulfilled when supply is powered on (e.g. fan on, external consents C6 or D5, dP
readout above the start threshold), the sequencer will automatically activate the EV outputs sequencially according to the times set by keyboard.

C4a AUTOMATIC OPERATION MODE

You can select the operation mode by keyboard in SET MODE. In automatic mode, the controls of the fan, the dP, C6 and D5 are active and the
activation of the cleaning cycle will depend on such functions.

C4b MANUAL OPERATION MODE

You can select the operation mode by keyboard in SET MODE. In manual mode, the control of the fan, the dP, C6 and D5 are not active.
C8 DP ZERO READOUT REGULATION
In this set up code it is possible to adjust the zero reading of differential pressure. In this function the display shows the dP reading and, with plant
stops or air pipes not connected if the dP reading is not 0.00 kPa it is possible to adjust it by key A and C.
C7c1 MINIMUM DP ALARM. CONTACT OPEN WITH ALARM. AUTOMATIC RESET.
If the dP readout is below the threshold in Set up, the minimum dP alarm is activated. The display shows the alarm condition code E8 (see the alarm
description) or the dP readout and letter L alternatively, according to the model.
The corresponding alarm relay will signal its condition. The alarm is automatically reset when the dP readout is above the threshold again.
If set to 'OFF' or 'E' (according to the model), the function is excluded.
NOTE: the minimum dP alarm is delayed by 60 seconds by default after the activation of the first washing cycle.
C7d1 MAXIMUM DP ALARM. CONTACT OPEN WITH ALARM. AUTOMATIC RESET.
If the dP readout is above the threshold in Set up, the maximum dP alarm is activated. The display shows the alarm condition code E7 (see the alarm
description) or the dP readout and letter H alternatively, according to the model.
The corresponding alarm relay will signal its condition. The alarm is automatically reset when the dP readout is below the alarm threshold again.
The activation of this alarm is delayed by 20 seconds by default.
C13_10 DP FULL RANGE 10KPA
Maximum differential pressure value measurable by the device 10.00 kPa = 100.0 mbar = 1012 mmH2O.
With dP reading over 10 kPa the display shows 'E' instead of the numeric value of dP.
D1b1 ADDITIONAL POST-CLEANING CYCLES FROM DP READOUT. ACTIVATION AT STOP.
In automatic operation mode, you can add a pre-set number of cleaning cycles after the fan stop. Their number can be set from 0 to 99 by keyboard.
The sequencer will automatically recognise the fan state by comparing the dP readout with the threshold in set code 11: dP > set 11 = fan on, dP <
set 11 = fan off.
Post-cleaning cycles are activated even if dP = 0.
When the fan is off or dP < set 11, the display shows 'FAN STOP'.
The display shows 'POST-CLEANING ACT' during additional cycles and if there is no alarm.
Post-cleaning cycles are activated only if the dP readout should reach the threshold value of cycle STOP in normal operation mode.
D5a CONSENT FROM EXTERNAL COMPRESSED AIR PRESSURE SWITCH
If the operation mode is automatic and contact D5a is open, the cleaning cycle stops, relay K2 indicates the alarm situation. Close D5a to restart the
washing cycle from the point where it had stopped. If contact D5a is open, the display shows alarm code E6.
NOTE: Link D5a clamps if it is not used with inputs from external contact active (See F01).
D6a ON/OFF CLEANING CYCLE FROM EXTERNAL CONTACT
If contact D6a is open, the cleaning cycle is not enabled and the display shows 'START CONTACT D6a OPEN'.
Close D6a to start cleaning cycle from the first electrovalve.
NOTE D6a: Jump D6a if it is not used with inputs on.
Pg. 7
D14a OPERATION HOURS-COUNTER
In SET MODE it is possible to visualize an hours counter. This counter is active when the cleaning cycle in On. In case of fan stop, consent D6 not
present or with the device in SET MODE the counter stops.
DPa 6X4 RILSAN AIR CONNECTIONS
G1 MAXIMUM LOAD POWER 25W PER OUTPUT
HVB INPUT AND OUTPUT VOLTAGE SELECTION
Use the jumpers on the board to select the supply voltage and the output voltage for the electrovalves. (See the drawing of the printed circuit layout).
JP1: Select the supply voltage between 115VAC and 230VAC.
JP2: Select the output voltage between 24, 115, 230 V (Only when the power supply is 115VAC or 230VAC).
JP3: Select the output voltage between AC and DC only when JP2 is set to 24V.
ATTENTION: set the same output voltage you have selected by means of the jumpers to adjust the trip threshold of the short-circuit. Otherwise, the
sequencer might malfunction or be damaged.
SL MULTI LANGUAGE DISPLAY
In Set up it is possible to select the language of all the descriptions showed by the display.

Pg. 8
Pg. 9
Pg. 10
Pg. 11
 ENCLOSURE TECHNICAL DATAS [7.1]

Material: ABS Temperature: -40°C ÷ 80°C

Protection degree: IP 65 Colour: Light grey

Pg. 12
 PROBLEMS SOLUTION

DEFECT POSSIBLE CAUSE SOLUTION

Display OFF Fuse burnt. Check the protection fuse on supply line.
Supply voltage. Check if supply voltage is present and if it agrees with
Jumper for input voltage selection supply voltage needed by the device (clamps 1 and 2).
Check jumper JP1

No output activation Output voltage. Check that sequencer output voltage and electrovalve
Connection to the electrovalves. coils have the same voltage.
Jumper for output voltage selection Check the connection between sequencer and
electrovalves and do manual test of the outputs (See
B10).
Check jumper JP2 and JP3.

Wrong differential pressure reading. Pneumatic connection not free. Disconnect the 2 pipe to the Timer and verify that dP
Pipe damaged reading is 0.00 kPa. If it is OK check the pipe for air
connection from the device to the filter.

The cleaning cycle do not run in The memory of the microprocessor could be Remove the supply voltage from the Timer. At the same
according to the set value. modified by external factor. time press key B and switch on the supply voltage. By
means of this operation the default data are loaded in
set up. Adjust the zero dP reading and the other
parameters according to the filter's needs.

WARRANTY

The warranty lasts 4 years. The company will replace any defective electronic component, exclusively at our laboratory,
unless otherwise agreed, upon the Company's prior consent.

WARRANTY EXCLUSION

The warranty is not valid in case of:

1) Tampering or unauthorized repairs.
2) Wrong use of the device, not in compliance with technical data.
3) Wrong electrical wiring.
4) Inobservance of the installation rules.
5) Use of the device, not in compliance with CE rules.
6) Atmospheric events (Lightning, electrostatic discharge), Overvoltage.

Pg. 13
 DICHIARAZIONE DI CONFORMITA' DEL COSTRUTTORE

CONFORMITY DECLARATION OF THE MANUFACTORY

Nome del costruttore: Manufactory name:

ESA Electronic Engineering ESA Electronic Engineering
Indirizzo del costruttore: Manufactory address
via J.Kennedy 28 I 20010 Mesero (Mi) Italia via J.Kennedy 28 I 20010 Mesero (Mi) Italia

Dichiara che il prodotto: Declare that the device:

Nome del Prodotto(i): Sequenziatore Device(s) name: Sequencer
Modello: DC Model: DC
Opzioni del prodotto: Tutte Device options: All

E' conforme alle seguenti direttive: Meets the following directive:

Direttiva 2004/108/CE 'compatibilità Directive 2004/108/CE

elettromagnetica' 'electromagnetic compatibility'
rispondenti alle related to the
norme Europee armonizzate European Standard
EN61000-6-2:2005 classe B della norma EN61000-6-2:2005 class B of the rule
EN61000-6-4:2001 EN61000-6-4:2001

Direttiva Bassa Tensione (DBT) 2006/95/CE Low Voltage Directive 2006/95/CE related to the
rispondente alle norme Europee armonizzate European Standard EN 60947-1:2004
EN 60947-1:2004

Informazioni supplementari: Additional informations

I prodotti sono stati sottoposti a test in the devices were tested in typical configuration
configurazione tipica e con potenza di carico with load power of 40 watt
40 watt

Mesero, 28 marzo, 2012

G. BELLINELLI
Amministratore delegato / Managing director

ESA ELECTRONIC ENGINEERING s.r.l.