EMCS OWNERS MANUAL

A detailed guide to program switching

1 Introduction
• Performance Without Compromise................................................. 1.1
• Identifying Your Stalk Type............................................................ 1.2

2 EMCS Programs & Features

• Security Code ............................................................................ 2.1
• Program Switching...................................................................... 2.2
• Fault Code Erase (FCE) & Throttle Body Alignment (TBA) .................... 2.3
• Security Lockout.......................................................................... 2.4
• Anti Theft .................................................................................. 2.5

3 Type A
• Enabling EMCS Mode................................................................. 3.1
• Security Code Entry .................................................................... 3.2
• Program Switching ..................................................................... 3.3
• Accessing Features ..................................................................... 3.4

4 Type B
• Enabling EMCS Mode................................................................. 4.1
• Security Code Entry .................................................................... 4.2
• Program Switching ..................................................................... 4.3
• Accessing Features ..................................................................... 4.4

5 Type C
• Enabling EMCS Mode................................................................. 5.1
• Security Code Entry .................................................................... 5.2
• Program Switching ..................................................................... 5.3
• Accessing Features ..................................................................... 5.4

6 Type D
• Enabling EMCS Mode................................................................. 6.1
• Security Code Entry .................................................................... 6.2
• Program Switching ..................................................................... 6.3
• Accessing Features ..................................................................... 6.4

7 Type E
• Enabling EMCS Mode................................................................. 7.1
• Security Code Entry .................................................................... 7.2
• Program Switching ..................................................................... 7.3
• Accessing Features ..................................................................... 7.4

8 ADDITIONAL NOTES FOR ADVANCED CONFIGURATIONS

1.1

Performance Without Compromise

Welcome to the APR family. Our sole mission is to engineer only the highest quality
tuning solutions for Volkswagen, Audi and Porsche vehicles ensuring the enthusiast
the ultimate driving experience while consistently providing the enthusiast the ultimate
in customer care and support.

EMCS is APR’s revolutionary patented Enhanced Modular Chipping System. EMCS

is an industry leading technology that brings many new features to the automotive
enthusiast. This technology was developed exclusively by APR, LLC and demonstrates
APR’s continued commitment to lead the industry with the most technologically
advanced products available.

APR’s ECU Upgrade is developed to work within the OEM and Tier 1 Supplier
specifications for engine component stress tolerances and performance
specifications. APR’s ECU upgrades are available in octane specific versions to
allow you to take full advantage of the fuel quality available in your area. APR’s
patented EMCS functionality puts the control of the engine’s operation at your finger
tips and allows for additional features and options to be installed to your OEM ECU.

Please take a moment to review the following pages and learn about the product this
company was founded on. Thank you for choosing APR and enjoy your enhanced
driving experience.

— The APR Team

1.2

Identifying Your Stalk Type

All EMCS control is facilitated through the cruise control stalk. The visual guide below
will help you identify which stalk you have for quick reference and instruction.

+
OFF
Type A
S CANCEL
E SPEED ON Cruise control stalk separate from turn signal stalk.
T – RESUME

RES/+ ON CANCEL OFF Type B

Cruise control stalk integrated into turn signal stalk.
SET/-

RES +
ON OFF
Type C
Cruise control stalk integrated into turn signal stalk.
SET -

RES
ON OFF
Type D
Cruise control stalk integrated into turn signal stalk.
SET

RES ON OFF
Type E
– +
Cruise control stalk integrated into turn signal stalk.
2

EMCS Programs & Features

2.1 Unique Security Code:
The unique security code is the key to locking and unlocking your software. Enter the
security code to gain access to program switching if security lockout is enabled, or
to disable the anti-theft feature. This option becomes available when purchased.
2.2 Program Switching:
When multiple programs have been purchased, accessing each program is
coordinated by pressing, holding and releasing the designated stalk-specific button
during one of the following sequences. Note: CEL = Check Engine Light
Program 1 - 1 CEL Blink per Second
(blink, pause, blink, pause, blink, pause, blink, pause)
Program 2 - 2 CEL Blinks per Second
(blink blink, pause, blink blink, pause, blink blink, pause, blink blink, pause)
Program 3 - 3 CEL Blinks per Second
(blink blink blink, pause, blink blink blink, pause, blink blink blink, pause, blink blink blink, pause)
Program 4 - 4 CEL Blinks per Second
(blink blink blink blink, pause, blink blink blink blink, pause, blink blink blink blink, pause, blink blink blink
blink, pause)

2.3 Fault Code Erase (FCE) and Throttle Body Alignment (TBA):
Until now the ability to erase fault codes has been something reserved only for those
with the proper tools. By purchasing this option you have the ability to erase most
fault codes that may cause a check engine light (CEL) in your car. Be advised, if
you do not know what is causing the CEL, professional diagnosis is recommended
before clearing it.
2.4 Locking Out Your ECU:
Purchasing this feature will allow you to temporarily disable and prevent
unauthorized program switching.
2.5 Anti-Theft*:
Anti-Theft is a valuable tool when faced with areas where your automobile may
be at risk of theft. Enabling this purchasable option deactivates ignition or throttle
response until you enter your unique access code. When security is unlocked, this
feature is accessible by entering the following button combination:
SET – SET – RESUME – RESUME – SET – SET – RESUME – RESUME
*This feature is accessible while the vehicle is running. To avoid accidental activation, lock out your ECU after selecting the desired program.
3

Type A
3.1 Enabling EMCS Mode: These four steps must be performed once before
successfully entering a security code, switching programs or accessing features.

KEY OFF CRUISE OFF

OFF
S + CANCEL
E SPEED ON
T – RESUME
PUSH

1 2

OFF
PULL
S + CANCEL
E SPEED ON
T – RESUME

3 4
KEY ON (Engine OFF) CRUISE ON

3.2 Security Code Entry:

OFF EL
S + CAN
C
E + OFF
ON
T SPEED CANC S D
PEE – RES
UME
E S
EL
– ON
RESU
ME
T

1 2
Raise the cruise control stalk (SPEED +) Lower the cruise control stalk (SPEED –)
X number of times to ENTER the digit. ONCE to REGISTER the digit.
Example entry on the following page.
Example Security Code Entry (code 2, 3, 2, 3):
2: SPEED+, SPEED+, SPEED –,
3: SPEED+, SPEED+, SPEED+, SPEED –,
2: SPEED+, SPEED+, SPEED –,
3: SPEED+, SPEED+, SPEED+, SPEED –
After this sequence is properly executed the CHECK
ENGINE LIGHT and the EPC LIGHT will flash alternately.

Note: This process is also used to deactivate Anti Theft and unlock Trial Software.

3.3 Program Switching:

Hold the set button. The check engine light will begin the flashing sequence
(SEE 2.2 FOR FLASH PATTERNS). Release the set button for the desired program
during the designated flash pattern.

OFF
S + CANCEL
E SPEED ON
T – RESUME
Type A
3.4 Accessing Features:
When multiple features have been purchased, accessing each feature is very simple.
Pull the cruise control stalk. The check engine light will begin the flashing sequence
(SEE FIGURE 3.4a FOR FLASH PATTERNS). Release the stalk for the desired feature
during the designated flash pattern.

OFF
PULL
S + CANCEL
E SPEED ON
T – RESUME

3.4a
Fault Code Erase - 1 Blink per Second
(blink, pause, blink, pause, blink, pause, blink, pause)
Throttle Body Alignment - 2 Blinks per Second
(blink blink, pause, blink blink, pause, blink blink, pause, blink blink, pause)
Security Lockout - 3 Blinks per Second
(blink blink blink, pause, blink blink blink, pause, blink blink blink, pause, blink blink blink, pause)
4

Type B
4.1 Enabling EMCS Mode: These four steps must be performed once before
successfully entering a security code, switching programs or accessing features.

KEY OFF CRUISE OFF

ON CANCEL OFF
RES/+

SET/-

1 2

ON CANCEL OFF
RES/+

SET/-

3 4
KEY ON (Engine OFF) CRUISE ON

4.2 Security Code Entry:

ON CANCEL OFF
RES/+
ON CANCEL OFF
RES/+

SET/-
SET/-

1 2
Press the SET button X number of times to Move cruise control rocker to CANCEL
ENTER the digit. and back to ON to REGISTER the digit.
Example entry on the following page.
Example Security Code Entry (code 2, 3, 2, 3):
2: SET, SET, CANCEL > ON,
3: SET, SET, SET, CANCEL > ON,
2: SET, SET, CANCEL > ON,
3: SET, SET, SET, CANCEL > ON
After this sequence is properly executed the CHECK
ENGINE LIGHT and the EPC LIGHT will flash alternately.

Note: This process is also used to deactivate Anti Theft and unlock Trial Software.

4.3 Program Switching:

Hold the set button. The check engine light will begin the flashing sequence
(SEE 2.2 FOR FLASH PATTERNS). Release the set button for the desired program
during the designated flash pattern.

ON CANCEL OFF
RES/+

SET/-
Type B
4.4 Accessing Features:
When multiple features have been purchased, accessing each feature is very simple.
Press and hold the RESUME button. The check engine light will begin the flashing
sequence (SEE 4.4a FOR FLASH PATTERNS). Release the button for the desired
feature during the designated flash pattern.

ON CANCEL OFF
RES/+

SET/-

4.4a
Fault Code Erase - 1 Blink per Second
(blink, pause, blink, pause, blink, pause, blink, pause)
Throttle Body Alignment - 2 Blinks per Second
(blink blink, pause, blink blink, pause, blink blink, pause, blink blink, pause)
Security Lockout - 3 Blinks per Second
(blink blink blink, pause, blink blink blink, pause, blink blink blink, pause, blink blink blink, pause)

NOTE:
Some ECU’s require the user to rock completely to the OFF position. If code entry
does not seem to work, Key off, Cruise off, Key on, Cruise on, then re-enter your
code substituting the OFF position for the cancel position.
5

Type C
5.1 Enabling EMCS Mode: These four steps must be performed once before
successfully entering a security code, switching programs or accessing features.

KEY OFF CRUISE OFF

ON OFF
RES +

SET -

1 2

ON OFF
RES +

SET -

3 4
KEY ON (Engine OFF) CRUISE ON

5.2 Security Code Entry:

ON OFF
RES + ON OFF
RES +

SET -
SET -

1 2
Press the SET button X number of times to Move cruise control rocker to OFF and
ENTER the digit. back to ON to REGISTER the digit.
Example entry on the following page.
Example Security Code Entry (code 2, 3, 2, 3):
2: SET, SET, OFF > ON,
3: SET, SET, SET, OFF > ON,
2: SET, SET, OFF > ON,
3: SET, SET, SET, OFF > ON
After this sequence is properly executed the CHECK
ENGINE LIGHT and the EPC LIGHT will flash alternately.

This process is also used to deactivate Anti Theft and unlock Trial Software.

5.3 Program Switching:

Hold the set button. The check engine light will begin the flashing sequence
(SEE 2.2 FOR FLASH PATTERNS). Release the set button for the desired program
during the designated flash pattern.

ON OFF
RES +

SET -

After releasing during the desired blink pattern, turn the KEY OFF
FOR 10 SECONDS. Turn the KEY ON and wait for the EPC and
CEL to stop flashing (if it does not flash, you’ve selected the same
program you were previously in).
Turn the KEY OFF AGAIN and then ON and GO!
Type C
5.4 Accessing Features:
When multiple features have been purchased, accessing each feature is very simple.
Press and hold the RESUME button. The check engine light will begin the flashing
sequence (SEE 5.4a FOR FLASH PATTERNS). Release the button for the desired
feature during the designated flash pattern.

RES +

SET -

5.4a
Fault Code Erase - 1 Blink per Second
(blink, pause, blink, pause, blink, pause, blink, pause)
Throttle Body Alignment - 2 Blinks per Second
(blink blink, pause, blink blink, pause, blink blink, pause, blink blink, pause)
Security Lockout - 3 Blinks per Second
(blink blink blink, pause, blink blink blink, pause, blink blink blink, pause, blink blink blink, pause)
6

Type D
6.1 Enabling EMCS Mode: These four steps must be performed once before
successfully entering a security code, switching programs or accessing features.

KEY OFF CRUISE OFF

ON OFF
RES

SET

1 2

ON OFF
RES

SET

3 4
KEY ON (Engine OFF) CRUISE ON

6.2 Security Code Entry:

ON OFF
RES
ON OFF
RES

SET
SET

1 2
Press the SET button X number of times to Move cruise control switch to OFF and
ENTER the digit. back to ON to REGISTER the digit.
Example entry on the following page.
Example Security Code Entry (code 2, 3, 2, 3):
2: SET, SET, OFF > ON,
3: SET, SET, SET, OFF > ON,
2: SET, SET, OFF > ON,
3: SET, SET, SET, OFF > ON
After this sequence is properly executed the CHECK
ENGINE LIGHT and the EPC LIGHT will flash alternately.

This process is also used to deactivate Anti Theft and unlock Trial Software.

6.3 Program Switching:

Hold the set button. The check engine light will begin the flashing sequence
(SEE 2.2 FOR FLASH PATTERNS). Release the set button for the desired program
during the designated flash pattern.

ON OFF
RES

SET

After releasing during the desired blink pattern, turn the KEY OFF
FOR 10 SECONDS. Turn the KEY ON and wait for the EPC and
CEL to stop flashing (if it does not flash, you’ve selected the same
program you were previously in).
Turn the KEY OFF AGAIN and then ON and GO!
Type D
6.4 Accessing Features:
When multiple features have been purchased, accessing each feature is very simple.
Press and hold the RESUME button. The check engine light will begin the flashing
sequence (SEE 6.4a FOR FLASH PATTERNS). Release the button for the desired
feature during the designated flash pattern.

ON OFF
RES

SET

6.4a
Fault Code Erase - 1 Blink per Second
(blink, pause, blink, pause, blink, pause, blink, pause)
Throttle Body Alignment - 2 Blinks per Second
(blink blink, pause, blink blink, pause, blink blink, pause, blink blink, pause)
Security Lockout - 3 Blinks per Second
(blink blink blink, pause, blink blink blink, pause, blink blink blink, pause, blink blink blink, pause)
7

Type E
7.1 Enabling EMCS Mode: These four steps must be performed once before
successfully entering a security code, switching programs or accessing features.

KEY OFF CRUISE OFF

RES ON OFF

– +

1 2

RES ON OFF

– +

3 4
KEY ON (Engine OFF) CRUISE ON

7.2 Security Code Entry:

RES ON OFF RES ON OFF

– + – +

1 2
Press the SET button X number of times to Move cruise control switch to OFF and
ENTER the digit. back to ON to REGISTER the digit.
Example entry on the following page.
Example Security Code Entry (code 2, 3, 2, 3):
2: SET, SET, OFF > ON,
3: SET, SET, SET, OFF > ON,
2: SET, SET, OFF > ON,
3: SET, SET, SET, OFF > ON
After this sequence is properly executed the CHECK
ENGINE LIGHT and the EPC LIGHT will flash alternately.

This process is also used to deactivate Anti Theft and unlock Trial Software.

7.3 Program Switching:

Hold the set button. The check engine light will begin the flashing sequence
(SEE 2.2 FOR FLASH PATTERNS). Release the set button for the desired program
during the designated flash pattern.

RES ON OFF

– +

After releasing during the desired blink pattern, turn the KEY OFF
FOR 10 SECONDS. Turn the KEY ON and wait for the EPC and
CEL to stop flashing (if it does not flash, you’ve selected the same
program you were previously in).
Turn the KEY OFF AGAIN and then ON and GO!
Type E
7.4 Accessing Features:
When multiple features have been purchased, accessing each feature is very simple.
Pull and hold the RESUME button. The check engine light will begin the flashing
sequence (SEE 7.4a FOR FLASH PATTERNS). Release the button for the desired
feature during the designated flash pattern.

RES ON OFF

– +

7.4a
Fault Code Erase - 1 Blink per Second
(blink, pause, blink, pause, blink, pause, blink, pause)
Throttle Body Alignment - 2 Blinks per Second
(blink blink, pause, blink blink, pause, blink blink, pause, blink blink, pause)
Security Lockout - 3 Blinks per Second
(blink blink blink, pause, blink blink blink, pause, blink blink blink, pause, blink blink blink, pause)
8

ADDITIONAL NOTES FOR ADVANCED CONFIGURATIONS:

As new vehicles are developed and released, there is the potential for this guide
to miss updated OEM configurations. These updates may deal not only with
cruise control stalks, but also ignition/key options. Please reference the following
instructions for your unpublished setup, or contact APR Tech Support for further
assistance. Email apr@goapr.com or call toll-free (800) 680-7921.

Dash Inserted Keys:

Some cars have keys that must be inserted into the dash of the car. On all VW/Audi
models the engine must be OFF, but the key must be ON in order to enable EMCS.
With your foot OFF the brake/clutch, begin by placing the key into its designated
slot on the dash. Press the key one time to illuminate the dashboard. Follow the
appropriate cruise control instructions found in previous sections of this manual.

Keyless Ignition:
Some vehicles do not require a key to be inserted anywhere to start the engine. As
stated before, to enable EMCS, the engine must be OFF, but the key must be ON.
With your foot OFF the brake/clutch, press the ENGINE START button one time to
illuminate the dashboard. Follow the appropriate cruise control instructions found in
previous sections of this manual.

Steering Wheel Cruise Functions:

Some vehicles have cruise control functions built into the steering wheel that do not
resemble Cruise Control Stalk Types A-E. Although there is no separate stalk, the
functions are performed the same. For this configuration please follow the instructions
for Stalk Type C.

Porsche EMCS:
The Porsche EMCS is different than any listed in this manual. Please contact APR
Tech Support to acquire digital instructions.
Email apr@goapr.com or call toll-free (800) 680-7921.
EMCS OWNER INFORMATION
Stalks, Programs & Options

CUSTOMER INFORMATION
Customer Name: crook, william
Serial Number:
582911 Date Installed: 9/25/2020
ECU Part # (“Box Code”): Factory Revision:
Audi A8 NA MY2013 4.0TFSI CEUA 4H0906014L S0005 Stage 1 V1.0 [APR
APR File Name: Mobile]

PROGRAMS (Programs designed ONLY for use with unleaded gasoline with a minimum octane rating as specified)
SLOT 1: MODE 1 - 93 Octane ((R+M)/2) Chipped Program*
SLOT 2: MODE 2 - 91 Octane ((R+M)/2) Chipped Program*
SLOT 3: MODE 3 - Stock Program
SLOT 4: MODE 4 - Valet Program

FAULT CODE ERASE / THROTTLE BODY ALIGNMENT

SECURITY CODE: V-TUNE

ANTI THEFT* TRIAL SOFTWARE
* Security Lockout is required to operate this feature.

STALK TYPE: (check one)

ON OFF RES ON OFF
ON OFF RES
OFF RES/+ ON CANCEL OFF RES +
S + CANCEL
E SPEED
T
ON – +
– RESUME SET
SET/- SET -

Type A Type B Type C Type D Type E

APR LLC, 4800 US HWY 280 WEST, Opelika, AL 36801

800.680.7921
334.502.5181
www.goapr.com