MODEL

CMS
COMPACT MOTION SWITCH
Economy model with one signal set point

WHAT IT IS, AND WHAT IT DOES OPERATION

The Model CMS Motion Sensing Control is a compact 1. The Model CMS senses motion by means of a
unit designed to include all mechanical and electronic precision metal disc mounted on the input shaft. This
components in one housing. It will produce an output disc generates measurable light pulses as a series
signal at a predetermined speed which may be either of slots on its periphery rotate past an infra-red light
underspeed or overspeed. Rugged, heavy duty source. A photo-electric sensor monitors the series of
construction combined with solid state electronics light pulses and converts them to a digital electronic
and photo-electric technology, make this one of the signal. Solid state circuitry then analyzes the digital
most advanced detectors available. signal and activates or deactivates the output relay
at the pre-set signal speed. The Model CMS has an
The Model CMS protects all valuable rotating adjustable built-in time delay eliminating the need for
equipment including belt conveyors, bucket elevators, a separate start-up time delay relay.
rotary feeders, or screw conveyors. It operates in
either a clockwise or counterclockwise direction and 2. The Model CMS will sense underspeed or overspeed
mounts in any position. conditions. Three signal speed ranges are available
MODEL CMS MOTION SPEED CONTROL with each unit. The low signal speed range is from 0.1
to 10 RPM. The medium signal speed range is 1 to 100
MODEL DESCRIPTION SHPG. WT. LBS.
RPM, and the high speed range is 10 to 1000 RPM.
CMS-1G 120 VAC General Purpose, NEMA 4, 4X 6

CMS-1X 120 VAC Explosion proof, NEMA 7/9 6

3. Field adjustment of the signal set point is easily
accomplished by means of an adjustment screw.
CMS-2G 240 VAC General Purpose, NEMA 4, 4X 6
The signal speed ranges are selected by a three
CMS-2X 240 VAC Explosion proof, NEMA 7/9 6 position toggle switch on the printed circuit board.
CMS-3G 24V AC/DC General Purpose, NEMA 4, 4X 6 For UNDERSPEED sensing, the signal point is set
CMS-3X 24V AC/DC Explosion proof, NEMA 7/9 6 below the normal operating speed of the unit. The
Epoxy coating option: add "E" to end of model number.
output relay will then de-energize if the speed drops
Dual Setpoint & Pulse Output Models available. Add "­–DSPO" to end of model number. below the signal set point. For OVERSPEED sensing
the signal set point is set above the normal operating
speed. The output relay will energize if the speed
exceeds the signal set point. The output relay can be
wired either normally open or normally closed.

4. Zero speed sensing can be accomplished by

locking the signal set point adjustment screw at
its lowest setting of 0.1 RPM. The output relay will
then de-energize when the shaft speed of the unit
approaches zero.

2 conveyorcomponents.com Conveyor Components Company • 800-233-3233 • Fax: 810-679-4510 • info@conveyorcomponents.com

 ALUMINUM ENCLOSURE
(EPOXY COATING OPTIONAL)

WIRING
The output of the Model CMS is a
BALL BEARINGS DP/DT relay connected to the
terminal block at the rear of the
unit. There are two sets of output
5/8” DIA. contacts. Each set includes normally
INPUT SHAFT
open, normally closed, and common.
As a result, the unit can be used to
PC BOARD control two separate circuits such
as a motor starter and a signal light.
PRECISION DISC Input power is connected from the
source to contacts L1, and L2. A
MODEL CMS ground connection is also furnished.
(Cut-Away View)

COMMON 1
MECHANICAL SPECIFICATIONS NORMALLY CLOSED 1
NORMALLY OPEN 1
INTERNAL VIEW
RADIAL LOAD ON INPUT SHAFT: 125 lb. max. NORMALLY OPEN 2
WITH COVER NORMALLY CLOSED 2
END THRUST ON INPUT SHAFT: 100 lb. max.
REMOVED COMMON 2
ROTATION: Either clockwise or counterclockwise L2
L1
DRIVING TORQUE: 1 inch-pound maximum
SHAFT: 5/8” diameter with 3/16” x 1” square key
ENCLOSURE: Aluminum with screw on cover. Optional
epoxy coating available.
MEETS: NEMA Type 3S, 4, 4X; or NEMA Type 7: Class
I, Groups C & D; NEMA Type 9: Class II, Groups F & G
BEARINGS: (2) Ball Bearings, permanently lubricated
and sealed for life
SPEED RANGE
SHAFT SEAL: Leather type oil seal
L H M
WEIGHT: 6 lb.
SIZE: 5” high x 5” wide x 8½” long GREEN L.E.D.
RELAY ENERGIZED
ELECTRICAL SPECIFICATIONS YELLOW L.E.D.
TIME DELAY
SPEED SET POINT
INPUT VOLTAGE: 105-135 A.C., 50/60 Hz. PULSES
210-250 volts A.C., 50/60 Hz. (Special Order)
OUTPUT: DPDT relay 3 Amp. Resistive at 120 volts A.C. DIMENSIONS SIDE VIEW
DPDT relay 3 Amp. Resistive at 240 volts A.C. 9” [228 mm]
2-1/2” 3/8” [10 mm]
DPDT relay 3 Amp. Resistive at 30 volts D.C. 4-3/4” [121 mm] 1-1/4” [64 mm]
3-3/4” [95 mm]
1/10 Horse Power at 120 volts A.C. [32 mm]
13/32” [10 mm]

1/10 Horse Power at 240 volts A.C.

AMBIENT TEMPERATURE: 14°F to 131°F (-10°C to 55°C)
4-1/2” [114 mm]

MAX. OPERATING TEMPERATURE: T6: 185°F (85°C) "X" units only

3-3/4” [95 mm]

REPEATABILITY: +2% max. at constant voltage and 4-7/8”

[124 mm]
temperature
2”
[51 mm]

POWER CONSUMPTION: 3 Watts maximum 7/16” [11 mm]

1-3/8”
FRONT VIEW 5/8” [16 mm] 3/4” NPT PIPE TAP
SPEED RANGES: 3 Signal Speed Ranges SHAFT DIA. [35 mm] (BOTH SIDES)

LOW: 0.1 to 10 RPM 3-1/4” [83 mm]

MEDIUM: 1 to 100 RPM 2-1/4”
[57 mm]
HIGH: 10 to 1000 RPM 7/8” [22 mm]

SIGNAL POINT: Speed at which relay will de-energize for 5/16”

MOUNTING [8 mm]
Underspeed, or energize for Overspeed. HOLE PLAN
1-1/4” [32 mm] DIA. HOLES
4 PLACES
Recommended to be 15-20% lower than
running speed. 1-1/4” [32 mm]
3-1/2” [89 mm]
This will eliminate nuisance shutdowns.
START UP DELAY: Adjustable up to 45 seconds 3
 MODEL CMS TECHNICAL INFORMATION
1/2” [13 mm]
GAP DRILL & TAP FOR 5/8”-11 N.C. THREAD -
1-13/16” [46 mm] RIGHT HAND - TAP 1-3/8” DEEP - USE
FLEXIBLE SHAFT COUPLING DRILL 1-3/4” [45 mm] DEEP
(PART NO. 304) 17/32” DIA. DRILL 1-3/4 DEEP (MIN.)
“A”
TAP 1-3/8” [35 mm] DEEP
SHAFT
BEARING PREFERRED
ROTATION
SEE NOTE* CL OF
SHAFT

DETAIL “X”

“B” *NOTE: When threaded stub shaft (Part 303 or equal) is to be used. It is recommended that the
location of the stub be in the end of the shaft that rotates counterclockwise. This allows the threads to
MODEL NO. MSD-1 continue being under a constant fastening torque while the shaft turns. If the rotation is clockwise or
/ MSD-1X the shaft is for reversing type service, make sure the jam nut is locked tight against the shaft.
PART NO. 310 5/8” [16mm] DIA. 3/16”
SENSOR MOUNTING STUB SHAFT NO. 303 [4.8 mm] Part No. 310 will fit parts No's. 311, 312 or 313
BRACKET WITH JAM NUT
SEE DETAIL “X” PART NO. Bearing
BEARING All Dimensions Are In Inches
311, 312, OR 313 Bracket
BEARING SUPPORT & Shim
BRACKET Plate
MOUNTING DIMENSIONS (SEE TABLE)
Shaft Diameter “A” “B” “C” “D”

311 1⁷⁄₁₆ 1₁⁄₄ to 2 1⁷⁄₈ to 2₁⁄₈ 3₁⁄₈ 1₁⁄₈

“C” “D” 312 1₁⁵⁄₁₆ to 2⁷⁄₁₆ 1₁⁄₂ to 2⁹⁄₁₆ 2₁⁄₄ to 3 3₃⁄₄ 1⅝
313 2₁⁵⁄₁₆ to 3₁⁵⁄₁₆ 3 to 3₃⁄₄ 3₁⁄₈ to 4₁⁄₈ 4₁⁄₂ 2₃⁄₁₆
ACCESSORIES FOR THE MODEL CMS (CMS-DSPO & MSD) BEARING BRACKETS AND SHIM PLATES FOR CMS

MOUNTING
The control can be mounted in any position, but the
mounting surface should be flat and smooth. The bearing
303 STUB SHAFT ⅝" dia.,
threaded one end, keyed other
304 FLEXIBLE COUPLINGS Avail-
able for connection of the CMS
brackets and shim plates shown in the chart can be used
end. With jam nut and ₃⁄₁₆" key. sensor to the driven shaft. to mount the unit directly to the pillow block supporting a
shaft. Normally, only 1/4” mounting bolts and lock washers
are required. If vibration is extreme two of the mounting
holes should be doweled and bolts used in the others.
The shaft of the device should be mounted in line with or
parallel to the driving shaft. Model CMS can be driven by
305 COUPLING GUARD 310 MOUNTING BRACKET 311, 312, 313 BEARING BRACKETS
Protection cover for For mounting CMS sensor to Attaches 310 mounting bracket to a flexible coupling, V-belt drive, chain drive, or gear drive.
coupling connection. rotary machinery. pillow block bearing assembly.

CMS DSPO
MECHANICAL ELECTRICAL
MODEL SPECIFICATIONS
RADIAL LOAD ON INPUT SHAFT: 125 lb. max.
SPECIFICATIONS
INPUT VOLTAGE: 105-135 volts AC, 50/60 Hz.
COMPACT MOTION SWITCH 210-250 volts Ac, 50/60 Hz. (Special Order)
DUAL SETPOINT & PULSE OUTPUT END THRUST ON INPUT SHAFT: 100 lb. max.
24 volts AC/DC, 50/60 Hz. (Special Order)
ROTATION: Either clockwise or
OUTPUT (RELAYS):
counterclockwise
DPDT relay to 3 Amp. Resistive at 120 volts AC
DRIVING TORQUE: 1 inch-pound maximum DPDT relay to 3 Amp. Resistive at 240 volts AC
SHAFT: 5/8” diameter with 3/16” x 1” square key DPDT relay to 3 Amp. Resistive at 30 volts DC
1/10 Horsepower at 120 volts AC
ENCLOSURE: Aluminum with screw on cover 1/10 Horsepower at 240 volts AC
MEETS: CMS-1G-DSPO: NEMA Types 3S, 4 & 4X OUTPUT (PULSE):
CMS-1X-DSPO: NEMA Type 7: Class I Groups C & D 12V DC NPN; 12 pulses per rev. with standard disk
NEMA Type 9: Class II Groups F & G 50 pulses per rev. with optional low-speed disk
The model CMS-DSPO motion sensing control is a (120 VAC units cULus Certified)
Epoxy coating option: add "E" to end of AMBIENT TEMPERATURE:
compact unit designed to include all mechanical and 14°F to +131°F (-10°C to 55°C)
electronic components into a single housing. It will model number.
produce a switching output signal at each of two BEARINGS: (2) Ball Bearings, permanently MAX. OPERATING TEMP. (CMS-X-DSPO):
predetermined speeds; which may be two over-speed, lubricated and sealed for life Class T6: 185°F (85°C)
two under-speed or one each over-speed and under- SHAFT SEAL: Leather type oil seal REPEATABILITY: +2% maximum at constant
speed. It also produces a pulse rate signal for external voltage and temperature.
monitoring with a PLC or Tachometer. WEIGHT: 6 lb.
SIZE: 5” high x 5” wide x 8½” long POWER CONSUMPTION: 3 Watts
Add "­–DSPO" to end of model number.

4 conveyorcomponents.com Conveyor Components Company • 800-233-3233 • Fax: 810-679-4510 • info@conveyorcomponents.com