Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 7 views

    JXBW 8040 400FR

    Uploaded by

    hosseinidokht

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    JXBW 8040 400FR

    Uploaded by

    hosseinidokht
    7 views2 pages

    Original Title

    JXBW-8040-400FR

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    7 views2 pages

    JXBW 8040 400FR

    Uploaded by

    hosseinidokht

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    NANJING JUNXIN ENVIRONMENTAL TECHNOLOGY CO.

    , LTD

    JXBW-8040-400- FR
    FR series of fouling resistant aromatic polyamide composite membrane element is developed by JX for complex water quality. FR series
    element with special membrane preparation process, it improved the hydrophilicity, charge characteristic and roughness, can effectively
    reduce the breeding of biofouling and adsorption of pollutants in the membrane surface. The element is applied a special 3 4 mil spacer design,
    which effectively reduced fouling and pressure drop, with more durable on cleaning can extent the service life.
    FR series of fouling resistant membranes normally suitable for treatment of complex water source with TDS less than 10 0 0 0 ppm. It is
    mainly used for purification of surface water, mining waste water, municipal reclaimed water, industrial waste water, RO brackish water,
    etc.
    Module Active Membrane Area Average Permeate Stable rejection Min rejection

    ft2 (m2) GPD (m³/d) Rate (％) Rate (％)

    BW-8040-400-FR 400 (37.2) 10500 (39.7) 99.75 99.5

    Test conditions：
    Testing pressure 225 Psi (1.55Mpa)
    Testing solution temperature 25℃
    Concentration of testing solution 2000ppm
    pH value of testing solution 7.0±0.5
    Recovery rate of Single element 15%
    Feed spacer： 34 mil (0.86 mm)
    Operation limits & conditions：
    Max. Working Pressure 600psi (4. 14Mpa)
    Max. Temperature of Feed water 45℃
    Max. Volume of Feed water 75gpm (17 m3/h)
    Max. Feed water SDI 1 5 5
    Max. Feed water Turbidity 1.0NTU
    pH Range of Feed water during Continuous Operation 2~11
    pH Range of Feed water during Chemical Cleaning 1~13
    Residual Chlorine Concentration of Feed Water ＜0. 1ppm
    Max. Pressure Drop of Single Membrane Element 15psi (0. 1Mpa)
    Max. Pressure Drop of Single Pressure Vessel with Six elements 50psi (0.34Mpa)
    Size of Membrane Element：1.0 inch = 25.4 mm

    A/mm(inch) B/mm(inch) C/mm(inch)


    1016(40) 200(7.89) 29( 1. 125)

    Notice:
    1 . All data and information provided in this manual have been obtained from long- term experiment by JX. We
    confirm the effective and accuracy of the data. assumes no liability for any aftermath caused by user’ s failure in
    abiding by the conditions specified in this manual in use or maintenance of membrane products. It is strongly
    recommended that the user shall strictly abide the designed use and maintenance requirements and keep relevant
    records.
    2. The permeate value listed in the table is the average value. The permeate flow of single membrane element is
    tolerance not exceeding ± 15% of the nominal value.
    3. All wet-type membrane elements have been strictly tested before leaving the factory, and have been treated with
    1 . 0 % sodium hydrogen sulfite ( 1 0 % glycerin antifreeze required in winter) for storage purpose, then sealed with
    plastic bag in vacuum, and further packed in cartonboxes.
    4. The membrane used should remain wet after being used; In long term suspension, to prevent the breeding of
    microbes, soak the membrane elements with protective solution is highly recommended, the solution ( prepared with
    RO filtered water) containing 1.0% sodium hydrogen sulfite (foodstuff-purpose).
    5. Operate low pressure flushing for 15-25 minutes of first use, high pressure flushing for 60-90 minutes when first
    use (Permeate volume no less than 50% of designed volume). Discard all the permeate and condensed water
    produced during the first one hour after system start- up.
    NANJING JUNXIN ENVIRONMENTAL TECHNOLOGY CO. , LTD
    6. During storage time and operation period, it is strictly prohibited to added any chemical medicament that may
    be harmful to membrane elements. In case of any violation in adding chemical medicament, JX assumes no liability
    for any damages incurred.
    7. Along with technical development and product renovation, all information will be subject to modification
    without prior notification. Please keep notice the website of JX for any updates of the product.

    www.jx-purification.com info@jx-purification.com 008618061698374

    You might also like