5-2. NE4040-ARM50 - 200311 - LHK - Ver 1.0

NE4040-ARM50
Acid Resistant NF Membrane
SPECIFICATIONS:
General Permeate flow rate1: 1,500 GPD (5.7 m3/day)

Features MgSO4 rejection 1 : 99.0%
CaCl2 rejection 2 : 85 - 95%
Effective membrane area: 85 ft2 (7.9 m2)
1. The stated product performance is based on data taken after 30 minutes of operation at the following
test conditions:
• 2,000 mg/L MgSO4 solution at 75 psig (0.52 MPa) applied pressure
• 15% recovery
• 77 oF (25 oC)
• pH 6.5–7.0
2. The stated product performance is based on data taken after 30 minutes of operation at the following
test conditions:
• 500 mg/L CaCl2 solution at 75 psig (0.52 MPa) applied pressure
• 15% recovery
• 77 oF (25 oC)
• pH 6.5–7.0
3. Minimum MgSO4 rejection is 98%.

4. Permeate flow rate for each element may vary +30 / -15%
5. Elements are supplied as dry-type. Dry elements are sealed in a poly bag and individually boxed.
Membrane type: Thin-Film Composite

Membrane material: Polyamide (PA)
Element configuration: Spiral-Wound, FRP Wrapping
Dimensions Part Number

and
Weight Model Name A B C D/E Inter-
Brine Seal
connector
40.0 inch 3.9 inch 0.75 inch 1.05 inch

NE4040-ARM50 SWA01050 SWA01046
(1,016 mm) (99 mm) (19 mm) (26.7 mm)
1. Each membrane element supplied with one brine seal, one interconnector (coupler) and four o-rings.
2. All NE4040 elements fit nominal 4.0 inch (101.6 mm) I.D. pressure vessels.
The information provided in this document is solely for informative purposes. It is the user’s responsibility to ensure
the appropriate usage of this product. Toray Advanced Materials Korea Inc. assumes no obligation, liability or damages
incurred for the misuse of the product or for the information provided in this document. This document does not
express or implies any warranty as to the merchantability or fitness of the product.
Toray Advanced Materials Korea Inc.

For more information on our products, company and regional contacts, please visit our website at www.csmfilter.com.
Product Specification Sheet / Model NE4040-ARM50
Page 1 of 2 Rev.1.0 March 2020
NE4040-ARM50
Acid Resistant NF Membrane
APPLICATION DATA:
Operating Limits · Max. Pressure Drop / Element 15 psi (0.1 MPa)

· Max. Pressure Drop / 240” Vessel 60 psi (0.41 Mpa)
· Max. Operating Pressure 600 psi (4.14 MPa)
· Max. Feed Flow Rate 75 gpm (17.0 m3/hr)
· Min. Concentrate Flow Rate 16 gpm (3.6 m3/hr)
· Max. Operating Temperature 113 oF (45 oC)
· Operating pH Range 3.0–10.0
· CIP pH Range 2.0–11.0
· Max. Turbidity 1.0 NTU
· Max. SDI (15 min) 5.0
· Max. Chlorine Concentration < 0.05 mg/L
Design Guidelines for Various · Wastewater Conventional (SDI < 5) 8–12 gfd
Water Sources · Wastewater Pretreated by UF/MF (SDI < 3) 10–14 gfd
· Seawater, Open Intake (SDI < 5) 7–10 gfd
· Seawater, Beach Well (SDI < 3) 8–12 gfd
· Surface Water (SDI < 5) 12–16 gfd
· Surface Water (SDI < 3) 13–17 gfd
· Well water (SDI < 3) 13–17 gfd
· RO permeate (SDI < 1) 21–30 gfd
Saturation Limits · Langlier Saturation Index (LSI) <+1.5

(Using Antiscalants)† · Stiff and Davis Saturation Index (SDSI) <+0.5
· CaSO4 230% saturation
· SrSO4 800% saturation
· BaSO4 6,000% saturation
· SiO2 100% saturation
†
The above saturation limits are typically accepted by proprietary antiscalant
manufacturers. It is the user’s responsibility to ensure proper chemical(s) and
concentration are dosed ahead of the membrane system to prevent scale
formation anywhere within the membrane system. Membrane elements fouled
or damaged due to scale formation are not covered by the limited warranty.
GENERAL HANDLING PROCEDURES

 Elements contained in the boxes must be kept dry at  Keep elements moist at all times after initial wetting.
room temperature (7–32°C; 40–95°F) and should not be
 Avoid excessive pressure and flow spikes.
stored in direct sunlight.
 Only use chemicals compatible with the membrane
 Permeate from the first hour of operation should be
elements and components. Use of such chemicals may
discarded to flush out the preservative solution. void the element limited warranty.
 Used elements should be immersed in a preservative
 Permeate pressure must always be equal or less than the
solution during storage, shipping and system shutdowns feed/concentrate pressure. Damage caused by permeate
to prevent biological growth and freezing. The standard back pressure voids the element limited warranty.
storage solution contains 1% by weight sodium bisulfite or
sodium metabisulfite (food grade). For short term storage
(i.e. one week or less) 1% by weight sodium metabisulfite
solution is adequate for preventing biological growth.
Toray Advanced Materials Korea Inc.

For more information on our products, company and regional contacts, please visit our website at www.csmfilter.com.
Product Specification Sheet / Model NE4040-ARM50
Page 2 of 2 Rev.1.0 March 2020

5-2. NE4040-ARM50 - 200311 - LHK - Ver 1.0

Uploaded by

Copyright:

Available Formats

5-2. NE4040-ARM50 - 200311 - LHK - Ver 1.0

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

5-2. NE4040-ARM50 - 200311 - LHK - Ver 1.0

Uploaded by

Copyright:

Available Formats

NE4040-ARM50

Acid Resistant NF Membrane

General Permeate flow rate1: 1,500 GPD (5.7 m3/day)

3. Minimum MgSO4 rejection is 98%.

Membrane type: Thin-Film Composite

Dimensions Part Number

40.0 inch 3.9 inch 0.75 inch 1.05 inch

Toray Advanced Materials Korea Inc.

Operating Limits · Max. Pressure Drop / Element 15 psi (0.1 MPa)

Saturation Limits · Langlier Saturation Index (LSI) <+1.5

GENERAL HANDLING PROCEDURES

Toray Advanced Materials Korea Inc.

You might also like