Re2540-Blf 171201

RE2540-BLF
Ultra-low pressure grade RO element for low TDS water
SPECIFICATIONS:
General Permeate flow rate: 930 GPD (3.5 m3/day)

Features Nominal salt rejection: 99.2%
Effective membrane area: 27 ft2 (2.5 m2)
1. The stated product performance is based on data taken after 30 minutes of operation at the following
test conditions:
• 500 mg/L NaCl solution at 100 psig (0.69 MPa) applied pressure
• 15% recovery
• 77 oF (25 oC)
• pH 6.5–7.0
2. Minimum salt rejection is 99.0%.

3. Permeate flow rate for each element may vary +25 / -25%.
4. All elements are vacuum sealed in a polyethylene bag containing 1.0% SBS (sodium bisulfite) solution
and individually packaged in a cardboard box.
Membrane type: Thin-Film Composite

Membrane material: Polyamide (PA)
Element configuration: Spiral-Wound, FRP Wrapping
Dimensions Part Number

Model Name A B C D/E Inter-
Brine Seal
connector
40.0 inch 2.4 inch 0.75 inch 1.05 inch

RE2540-BLF SWA01050 SWA01047
(1,016 mm) (60.8 mm) (19.1 mm) (26.7 mm)
1. Each membrane element supplied with one brine seal, one interconnector (coupler) and four o-rings.
2. All RE2540 elements fit nominal 2.5 inch (63.5 mm) I.D. pressure vessels.
The information provided in this document is solely for informative purposes. It is the user’s responsibility to ensure
the appropriate usage of this product. Toray Chemical Korea Inc. assumes no obligation, liability or damages incurred
for the misuse of the product or for the information provided in this document. This document does not express or
implies any warranty as to the merchantability or fitness of the product.
For more information on our products, company and regional contacts, please visit our website at www.csmfilter.com.
Product Specification Sheet / Model RE2540-BLF
Page 1 of 2 Rev.3.1 December 2017
RE2540-BLF
Ultra-low pressure grade RO element for low TDS water
APPLICATION DATA:
Operating Limits · Max. Pressure Drop / Element 15 psi (0.1 MPa)

· Max. Pressure Drop / 240” Vessel 60 psi (0.41 Mpa)
· Max. Operating Pressure 600 psi (4.14 MPa)
· Max. Feed Flow Rate 6 gpm (1.36 m3/hr)
· Min. Concentrate Flow Rate 1 gpm (0.23 m3/hr)
· Max. Operating Temperature 113 oF (45 oC)
· Operating pH Range 2.0–11.0
· CIP pH Range 1.0–13.0
· Max. Turbidity 1.0 NTU
· Max. SDI (15 min) 5.0
· Max. Chlorine Concentration < 0.05 mg/L
Design Guidelines for Various · Wastewater Conventional (SDI < 5) 8–12 gfd
Water Sources · Wastewater Pretreated by UF/MF (SDI < 3) 10–14 gfd
· Seawater, Open Intake (SDI < 5) 7–10 gfd
· Seawater, Beach Well (SDI < 3) 8–12 gfd
· Surface Water (SDI < 5) 12–16 gfd
· Surface Water (SDI < 3) 13–17 gfd
· Well water (SDI < 3) 13–17 gfd
· RO permeate (SDI < 1) 21–30 gfd
Saturation Limits · Langlier Saturation Index (LSI) <+1.5

(Using Antiscalants)† · Stiff and Davis Saturation Index (SDSI) <+0.5
· CaSO4 230% saturation
· SrSO4 800% saturation
· BaSO4 6,000% saturation
· SiO2 100% saturation
†
The above saturation limits are typically accepted by proprietary antiscalant
manufacturers. It is the user’s responsibility to ensure proper chemical(s) and
concentration are dosed ahead of the membrane system to prevent scale
formation anywhere within the membrane system. Membrane elements fouled
or damaged due to scale formation are not covered by the limited warranty.
GENERAL HANDLING PROCEDURES

 Elements contained in the boxes must be kept dry at  Keep elements moist at all times after initial wetting.
room temperature (7–32°C; 40–95°F) and should not be  Avoid excessive pressure and flow spikes.
stored in direct sunlight. If the polyethylene bag is
damaged, a new preservative solution (sodium bisulfite)  Only use chemicals compatible with the membrane
must be added and air-tight sealed to prevent drying and elements and components. Use of such chemicals may
biological growth. void the element limited warranty.
 Permeate from the first hour of operation should be  Permeate pressure must always be equal or less than the
discarded to flush out the preservative solution. feed/concentrate pressure. Damage caused by permeate
back pressure voids the element limited warranty.
 Elements should be immersed in a preservative solution
during storage, shipping and system shutdowns to prevent
biological growth and freezing. The standard storage
solution contains 1% by weight sodium bisulfite or sodium
metabisulfite (food grade). For short term storage (i.e.
one week or less) 1% by weight sodium metabisulfite
solution is adequate for preventing biological growth.
For more information on our products, company and regional contacts, please visit our website at www.csmfilter.com.
Product Specification Sheet / Model RE2540-BLF
Page 2 of 2 Rev.3.1 December 2017

Re2540-Blf 171201

Uploaded by

Copyright:

Available Formats

Re2540-Blf 171201

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Re2540-Blf 171201

Uploaded by

Copyright:

Available Formats

RE2540-BLF

Ultra-low pressure grade RO element for low TDS water

General Permeate flow rate: 930 GPD (3.5 m3/day)

2. Minimum salt rejection is 99.0%.

Membrane type: Thin-Film Composite

Dimensions Part Number

40.0 inch 2.4 inch 0.75 inch 1.05 inch

Operating Limits · Max. Pressure Drop / Element 15 psi (0.1 MPa)

Saturation Limits · Langlier Saturation Index (LSI) <+1.5

GENERAL HANDLING PROCEDURES

You might also like